Search NASA⌕ Search

SEARCH · Search NASA

Results for “texturization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

Characterization of Recrystallized Grains During Static Recrystallization of Hot-Compressed Mg–Zn–Ca Alloys Using In Situ Far-Field High-Energy Diffraction Microscopy

In this study, we explored the effect of Zn content on the static recrystallization of three 80 pct hot-compressed alloys, Mg–0.5Zn–0.1Ca wt pct (ZX050), Mg–1Zn–0.1Ca wt pct (ZX10), and Mg–3.2Zn–0.1Ca wt pct (ZX30), using far-field high-energy microscopy (ff-HEDM). Individual recrystallized grains were tracked and their 3D centroid, relative volume, and grain-averaged crystallographic orientation were measured during annealing. These measurements were used to compare the recrystallization kinetics and texture evolution of recrystallized grains in ZX alloys as a function of the Zn content. Fully recrystallized microstructures were observed for the ZX30 and the ZX10 alloys after annealing at 230 °C and 330 °C, respectively. In contrast, only a partially recrystallized microstructure for the ZX050 alloy was observed after > 1 hour of annealing at 430 °C. The resistance to recrystallization with decreasing Zn content was also confirmed by detecting faster growth rates of recrystallized grains in the ZX10 and ZX30 alloys, and slower growth rates in the ZX050 alloy. The significant recrystallization texture weakening of the ZX10 and ZX30 alloys and the development of a basal texture in the ZX05 alloy were described based on the orientation dependency of nucleation and growth of recrystallized grains. The analysis demonstrated that texture weakening was associated with increasing Zn content in Mg–Zn–Ca alloys.

Roumina, Reza [Univ. of Michigan, Ann Arbor, MI (U↗

Orientation Relationships of Pure Tin on Single Crystal Germanium Substrates

The limited number of independent β-Sn grain orientations resulting from the difficulty in nucleating β-Sn during solidification of Sn-based solders has a large effect on the resulting β-Sn grain size and, hence, on overall solder joint performance and reliability. This study analyzes the efficacy of Ge as a heterogeneous nucleation agent for β-Sn by observing the morphologies and orientation relationships of as-deposited, solid-state annealed, and liquid-state annealed pure Sn films on single crystal Ge (100), (110), and (111) substrates. Here, the results from scanning electron microscopy and electron backscatter diffraction showed that the as-deposited Sn films all deposited with a Sn (001)|| z-axis texture, regardless of the underlying Ge substrate orientation. Solid-state annealing at 150 °C for 5 min did not result in significant dewetting of the Sn films, and the films maintained their as-deposited texture of Sn (001)|| z-axis, regardless of the underlying Ge substrate orientation. Liquid-state annealing at 235 °C for 1 min resulted is large-scale dewetting of the Sn films and re-orientation of the Sn films on the various Ge substrates. After solidification, the Ge (100) and (110) single crystal substrates produced patches of dewetted grains of the same orientation but there were no consistent Sn grain textures after liquid-state annealing, suggesting no single orientation relationship. In contrast, solidification on Ge (111) single crystal substrates resulted in isolated grains with a single Sn film texture and an orientation relationship of (100) Sn ∥(111) Ge and [100] Sn ∥[110] Ge . Density Functional Theory simulations of the experimentally observed Ge (111) sample orientation relationship and the Ge/Sn cube-on-cube orientation relationship suggest favorable relative interfacial binding energies for both interface orientations.

36 MATERIALS SCIENCE↗

Electron Backscattered Diffraction Study of Pulse Electrodeposited Cu-Y{sub 2}O{sub 3} Composite Coating

The current investigation is an effort of correlating the grain growth, crystallographic orientation and second-phase Y{sub 2}O{sub 3} particles to the mechanical properties of the electrodeposited pure copper (Cu) and Cu-Y{sub 2}O{sub 3} coatings. Energy-dispersive spectrum and elemental mapping confirm the codeposition of Y{sub 2}O{sub 3} in the composite coating matrix, which indeed justifies the composite (Cu-Y{sub 2}O{sub 3}) coating. Both pure Cu and Cu-Y{sub 2}O{sub 3} coatings have (101) preferred orientation; however, the volume fraction is found comparatively lower in composite coating. Both microstructural and textural characterization through electron backscattered diffraction technique show significant grain refinement in case of Cu-Y{sub 2}O{sub 3} composite coating compared to pure Cu coating, and prominent 〈011〉 fiber texture is observed in case of pure Cu coating compared to composite coating. By the addition of second-phase Y{sub 2}O{sub 3} in the matrix, the 〈011〉 fiber texture is disintegrated and concentrated at ϕ{sub 1} = 37°, ϕ = 45°, ϕ{sub 2} = 0°. Despite lower volume fraction of 〈011〉 fiber texture, better mechanical properties (hardness and wear resistance) of the composite coating compared to pure Cu coating can be attributed to finer grain size, higher misorientation angle and incorporation of second-phase Y{sub 2}O{sub 3} particles.

36 MATERIALS SCIENCE↗

Shear Assisted Processing and Extrusion (ShAPE™) of AZ91E Flake: A Study of Tooling Features and Processing Effects

Charges of melt-spun AZ91E flake were indirectly extruded into tubes using Shear Assisted Processing and Extrusion (ShAPE™). The effect of instrument parameters and tool features on densification and microstructural evolution was studied. At a constant extrusion ratio, the tool rotational velocity varied from 75 to 300 rpm and was demonstrated to reduce the forge force by a factor of four. Modification of the extrusion die face with successively more aggressive scrolled features was found to enhance material flow into the extrusion orifice which led to a 30% reduction in spindle torque. Microstructure, texture and hardness are reported for the range of rpm and scroll geometries investigated. It was observed that the ShAPE™ process is able to retain the average grain size of the as-spun flake (2.5-4 μm) while simultaneously imparting strong textural alignment in the resultant tube.

36 MATERIALS SCIENCE↗

Quantitative characterization of gradient microstructures: A study on friction stir spot processing of pure cobalt

Heterogeneous microstructures in polycrystalline metals can enhance the strength and ductility, outperforming homogeneous structures of similar composition. This study investigates deformed cobalt via friction stir spot processing with varying dwell times to uncover the effects of plastic deformation and heat generation on the formation of morphological, phase, and grain boundary character gradients. A new approach to quantify the morphological gradients in materials, which describes grain morphology in terms of density followed by parametric regression, enables direct quantification of processing depth and gradient sharpness. Results show that longer processing times increase the steepness of morphological gradients and reduce the deformation depth for friction stir spot processing with low plunge depths and high tool rotational speeds. The amount of retained FCC is increased in the shorter processing conditions, primarily due to refined grain size, increased defect content, and reduced heat generation. Crystallographic texture analysis of the HCP phase indicated a dominant B-fiber described by (0001) ∥ shear plane normal in the extreme processing conditions and the formation of a P-fiber, shear direction ∥ ⟨11$\bar2$0⟩ for intermediate dwell times. The texture of the FCC phase for low processing times was a C texture {100}⟨011⟩ where longer processing times were dominated by a [001] fiber texture with a main {110}⟨100⟩ orientation and emergence of a slight [111] fiber in the longest processing condition. The approaches outlined in this work give insight into quantifying gradients and improve the understanding of highly deformed cobalt.

36 MATERIALS SCIENCE↗

Parametrically designed surface topography on CAD models of additively manufactured lattice structures for improved design validation

Additively Manufactured (AM) lattice structures of the laser powder bed fusion (LPBF) process generally have different surface geometries depending on the overhang angle and location. This means that the design validation stage is often challenging, considering it is based on an ideal Computer Aided Design (CAD) model that is not truly representative, since the AM part will be different in terms of dimensional accuracy and surface finish. Previous studies have relied on the design of surface textures that are independent of the overhang angle, or techniques based on directly using X-ray Computed Tomography (XCT) data. In this paper, a new technique for designing surface texture on the CAD of lattices has been investigated and correlated with areal surface roughness parameters. After extracting areal surface parameters from the XCT data of the lattice, the method allowed for the design of this surface texture on the part CAD taking in consideration if its up skin or down skin, without using XCT data as the main input. By applying this method, it is possible to obtain a lattice CAD model with a designed surface texture and geometry that is more representative of the actual AM lattice. The mean deviation between the CAD model with the designed surface and the XCT was a third of the one between the XCT and the initial CAD. The proposed method allows for designing and replicating LPBF AM surfaces on the CAD of a lattice, taking into consideration the dimensional deviation caused by AM surfaces, especially on overhangs. Assuming that an LPBF AM process is stable and produces approximately the same AM surface, this method can be used to predict the geometry of a lattice, providing a cost-effective and efficient methodology that minimizes the time needed for design validation.

42 ENGINEERING↗

Classification scheme for sedimentary and igneous rocks in Gale crater, Mars

Rocks analyzed by the Curiosity rover in Gale crater include a variety of clastic sedimentary rocks and igneous float rocks transported by fluvial and impact processes. Here, to facilitate the discussion of the range of lithologies, we present in this article a petrological classification framework adapting terrestrial classification schemes to Mars compositions (such as Fe abundances typically higher than for comparable lithologies on Earth), to specific Curiosity observations (such as common alkali-rich rocks), and to the capabilities of the rover instruments. Mineralogy was acquired only locally for a few drilled rocks, and so it does not suffice as a systematic classification tool, in contrast to classical terrestrial rock classification. The core of this classification involves (1) the characterization of rock texture as sedimentary, igneous or undefined according to grain/crystal sizes and shapes using imaging from the ChemCam Remote Micro-Imager (RMI), Mars Hand Lens Imager (MAHLI) and Mastcam instruments, and (2) the assignment of geochemical modifiers based on the abundances of Fe, Si, alkali, and S determined by the Alpha Particle X-ray Spectrometer (APXS) and ChemCam instruments. The aims are to help understand Gale crater geology by highlighting the various categories of rocks analyzed by the rover. Several implications are proposed from the cross-comparisons of rocks of various texture and composition, for instance between in place outcrops and float rocks. All outcrops analyzed by the rover are sedimentary; no igneous outcrops have been observed. However, some igneous rocks are clasts in conglomerates, suggesting that part of them are derived from the crater rim. The compositions of in-place sedimentary rocks contrast significantly with the compositions of igneous float rocks. While some of the differences between sedimentary rocks and igneous floats may be related to physical sorting and diagenesis of the sediments, some of the sedimentary rocks (e.g., potassic rocks) cannot be paired with any igneous rocks analyzed so far. Finally, in contrast, many float rocks, which cannot be classified from their poorly defined texture, plot on chemistry diagrams close to float rocks defined as igneous from their textures, potentially constraining their nature.

58 GEOSCIENCES↗

Experimental verification of a crystal plasticity-based simulation framework for predicting microstructure and geometric shape changes: Application to bending and Taylor impact testing of Zr

This paper is concerned with experimental verification of a recently developed multi-scale simulation framework for plastic deformation of metallic materials from quasi-static to impact deformation conditions. The framework is a visco-plastic self-consistent (VPSC) polycrystalline model embedded in an implicit finite element method (FE-VPSC) to provide a microstructure-sensitive constitutive response at each material point. Each material point of the FEM model is a polycrystalline aggregate with crystallographic deformation mechanisms operating at the single crystal scale with their evolving activity based on a dislocation density-based hardening law and texture. Four beams and three cylinders machined in different orientations from a textured plate of high-purity zirconium are tested quasi-statically in 4-point bending and at speeds of 100 m/s, 170 m/s and 243 m/s during Taylor impact tests, respectively. The variation in dimensional changes resulting from different sample orientations in the plate with respect to loading directions is measured for each sample. Moreover, texture and twinning characterization is performed using electron backscattered diffraction (EBSD). The deformation processes and underlying evolution of microstructure are successfully simulated using the FE-VPSC framework. In doing so, the model parameters are optimized and validated across a broad range of strain rates and temperatures. Simulation results in terms of geometrical changes and microstructural evolution are compared with the experimental measurements. The model predicts anisotropic material flow resulting from the hard-to-deform crystallographic directions, the development of gradients in texture and twinning through the geometries, tension–compression asymmetry, as well as the extent of plasticity under impact.

42 ENGINEERING↗

Investigation of the shear response and geometrically necessary dislocation densities in shear localization in high-purity titanium

The influence of microstructural anisotropy on shear response of high-purity titanium was studied using the compact forced-simple-shear specimen (CFSS) loaded under quasi-static loading conditions. Post-mortem characterization reveals significant difference in shear response of different directions in the same material due to material crystallographic texture anisotropy. Shear bands are narrower in specimens in which the shear zone is aligned along the direction with a strong {0001} basal texture. Twinning was identified as an active mechanism to accommodate strains in the shear region in both orientations. This paper confirms the applicability of the CFSS design for the investigation of differences in the shear response of materials as a function of process-induced crystallographic texture. A detailed, systematic approach to quantifying shear band evolution by evaluating geometrically necessary dislocations (GND) associated with crystallographic anisotropy is presented. Finally, the results show that: i) line average GND density profiles, for Ti samples that possess a uniform equiaxed-grain structure, but with strong crystallographic anisotropy, exhibit significant differences in GND density close to the shear band center; ii) GND profiles decrease steadily away from the shear band as the plastic strain diminishes, in agreement with Ashby's theory of work hardening, where the higher GND density in the through-thickness (TT) orientation is a result of restricted < a > type slip in the shear band compared with in-plane (IP) samples; iii) the anisotropy in deformation response is derived from initial crystallographic texture of the materials, where GND density of < a > GNDs are higher adjacent to the shear band in the through-thickness sample oriented away from easy slip, but the density of < c+a > type GNDs are very similar in these two samples; and iv) the increase in grain average GND density was determined to have strong correlation to an increase in the Euler Φ angle of the grain average orientation, indicating an increased misorientation angle evolution.

36 MATERIALS SCIENCE↗

In-situ neutron diffraction of a quasicrystal-containing Mg alloy interpreted using a new polycrystal plasticity model of hardening due to {10.2} tensile twinning

Due to the excellent balance of strength and ductility exhibited by some Mg-Zn-RE (Y subgroup rare earth element) alloys, which contain icosahedral quasicrystalline precipitates, it is of interest to examine their deformation mechanisms. Furthermore, the internal strain evolution Mg-3at%Zn-0.5 at%Y with 4 vol% i-phase was measured using in-situ neutron diffraction. The extruded samples exhibit an initially weak <10.0> || extrusion direction “rod texture,” distinct from the normally strong texture of extruded Mg alloys, but the grain size is unexceptional (16.7 ± 2.1 μm). The initially weak texture contributes to a nearly symmetric yielding response between tension and compression. The hardening responses are asymmetric, however, since {10.2} extension twinning is significantly more active during compressive straining, despite the initially weak texture. In-situ neutron diffraction tension and compression experiments parallel to the extrusion direction, together with elasto-plastic self-consistent (EPSC) crystal plasticity modeling, reveal the strength and hardening behavior of individual slip and twinning modes. A model that was previously published about twinning-detwinning (TDT) is implemented within the EPSC framework, and it is proven effective for describing the observed, mild tension-compression asymmetry. This is not possible with previous EPSC-based models of twinning. Finally, the description of hardening within the TDT model is modified, in order to accurately describe the evolution of internal strains within the twins.

36 MATERIALS SCIENCE↗

Effects of build orientation and heat treatment on the evolution of microstructure and mechanical properties of alloy Mar-M-509 fabricated via laser powder bed fusion

We present the main results from an experimental investigation into the consequences of various microstructural features, created by laser powder bed fusion (LPBF) and subsequent heat treatments (HTs), in alloy Mar-M-509 on several aspects of plastic deformation including mechanical anisotropy and elongation-to-fracture (ETF). To ensure successful manufacturing of the alloy, porosity fraction and distribution are first characterized using micro X-ray computed tomography. Next, grain structure, crystallographic texture, and regions of recrystallization in the studied microstructures are measured using electron backscattered diffraction (EBSD). Lastly, chemistry, distribution, and morphological features of carbide phases are extracted using electron microscopy and X-ray diffraction. Strength in tension and compression are measured at room temperature for different initial microstructures created by variations in manufacturing conditions and sample orientations with respect to sample processing frame. While the strength of the alloy varies with sample orientation by approximately 30% in the as-built condition, the alloy is softer, more ductile, and approximately isotropic after HT. These results are discussed and critically compared with the data reported for the as-cast material. The alloy manufactured via LPBF is found to be significantly stronger and more ductile than the same alloy produced by casting. The interesting deformation behavior characteristics of the samples in different conditions are explained in terms of their microstructures. EBSD measurements reveal evolution from columnar grains along the build direction favoring a moderately strong <001> fiber texture in the as-built material to equiaxed grains favoring the {110}<001> Goss texture component after subsequent HTs. The major change in grain structure and texture is a result of recrystallization. While carbide phases precipitate primarily at dendrite and cellular interfaces in the as-built material, these phases are both intra-and inter-granular within the HT materials and coarsen with HT duration. These microstructural observations formed bases to rationalize the observed mechanical behavior of the alloy. With this being said, tailoring the alloy performance characteristics with HTs is reported on.

36 MATERIALS SCIENCE↗

A new micromechanics based full field numerical framework to simulate the effects of dynamic recrystallization on the formability of HCP metals

This work presents a new full-field, efficient and mesh-free numerical framework to model microstructure evolution, dynamic recrystallization (DRX) and formability in hexagonal closed-packed (HCP) metals such as magnesium alloys at warm temperatures. A rate tangent-fast Fourier transform-based elasto-viscoplastic crystal plasticity constitutive model for HCP metals (RTCP-FFT-HCP) is coupled with a probabilistic cellular automata (CA) approach to model DRX (CA-DRX). Furthermore, this new model is coupled with the Marciniak-Kuczynski (M-K) approach to model formability of magnesium alloys at elevated temperatures. The RTCP-FFT-HCP model computes macro stress-strain, twinning volume fraction, micromechanical fields, texture evolution and local dislocation density. Nucleation of new grains and their subsequent growth is modeled using the cellular automata approach with probabilistic state switching rule. First, the proposed RTCP-FFT-HCP model is validated by comparing the predicted stress-strain responses and texture evolution under uniaxial tension and compression with experimental measurements for AZ31 sheet alloy at room temperature. The coupled CA-RTCPFFT-HCP model is further validated by comparing the predicted stress-strain responses and texture evolution in uniaxial compression with experimental measurements at 100 °C, 200 °C and 300 °C for the AZ31 sheet alloy. Next, the forming limit diagrams (FLDs) with and without including the effects of DRX are simulated at 100 °C, 200 °C and 300 °C for AZ31 sheet alloy. The predicted FLDs with DRX show very good agreement with the experimental measurements and clearly demonstrate the need for an accurate DRX model. The study reveals that the DRX strongly affects the deformed grain structure, grain size and texture evolution and also highlights the importance accounting for DRX during FLD simulations at high temperatures.

36 MATERIALS SCIENCE↗

Development of rare-earth-free bulk magnets with energy product up to 12 MGOe in field annealed Mn–Bi–Mg–In–Sb alloys

A treatment consisting of annealing in a moderately strong, ≤30 kOe, magnetic field was applied to arc-melted ingots and compacted melt-spun alloys with composition Mn 50 Bi 50-x-y-z Mg x In y Sb z . The high degree of texture of the magnetic α phase induced with annealing of the ingot samples (except the Mn–Bi–Sb one) allowed for accurate determination of the phase anisotropy field. Alloying was found to increase the anisotropy field from 45 kOe in the Mn 50 Bi 50 alloy to 65 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 alloy. In the compacted melt-spun alloys subjected to field annealing, a higher degree of texture could be achieved after compaction which had involved less heating, when a smaller fraction of the metastable β' phase had been converted into the α phase; compaction at room temperature allowed for the highest degree of texture in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The addition of indium was found to decrease the solidus temperatures of the alloys, facilitating the development of the α phase during the field annealing and modifying the properties of the resulting magnets. Introduction of indium resulted in a higher coercivity H c of the Mn–Bi–Mg–In magnets and in a better texture of the Mn–Bi–Mg–Sn–In magnets. The former effect allowed, in particular, for a viable maximum energy product ( BH ) max of 10 MGOe to be developed in the Mn 50 Bi 46.5 Mg 3 In 0.5 magnet through annealing in a relatively low field of 15 kOe, whereas the latter effect allowed for an excellent combination of ( BH ) max = 11.6 MGOe and H c = 8.5 kOe in the Mn 50 Bi 45 Mg 3 In 0.5 Sb 1.5 magnet. The highest ( BH ) max of 12 MGOe was realized in the Mn 50 Bi 46 Mg 3 In 0.5 Sb 0.5 magnet.

36 MATERIALS SCIENCE↗

Thin La{sub 2}Zr{sub 2}O{sub 7} films made from a water-based solution

Thin films of La{sub 2}Zr{sub 2}O{sub 7} (LZO) are highly regarded as possible buffer layers in the coated conductor configuration. This report describes a new synthesis for thin crystalline LZO films, based on a largely water-based solution, mainly containing metal acetates, acetic acid and an organic amine-base: triethanolamine. Initially, a thin layer of amorphous material is deposited on the textured Ni-5 at%W substrate by means of dip-coating. Only by careful control of the thermal treatment can the layer be transformed into a crystalline layer. Important parameters in this respect are the heating rate and the dwell time. The amorphous gel is analysed by HR-TGA/DTA and HR-TEM. The textured layers are analysed by XRD, pole figures, RHEED, AFM and SEM. - Grapical Abstract: Thin films of La2Zr2O7 (LZO) are produced via a water-based solution, containing metal acetates, acetic acid and triethanolamine. The thin layer is deposited on the textured Ni-5 at%W substrate by dip-coating. The amorphous gel is analysed by HR-TGA/DTA and HR-TEM. The textured layers are analysed by XRD, pole figures, RHEED analysis, AFM and SEM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron backscattering diffraction analysis of an ancient wootz steel blade from central India

The electron backscattering diffraction technique was used to analyse the nature of carbides present in an ancient wootz steel blade. Bulky carbides, pro-eutectoid carbide along the prior austenite grain boundaries and fine spheroidized carbides were detected. Electron backscattering diffraction was employed to understand the texture of these carbides. The orientations of the cementite frequently occur in clusters, which points to a common origin of the members of the cluster. For the bands of coarse cementite, the origin is probably large coarse particles formed during the original cooling of the wootz cake. Pearlite formed earlier in the forging process has led to groups of similarly oriented fine cementite particles. The crystallographic texture of the cementite is sharp whereas that of the ferrite is weak. The sharp cementite textures point to the longevity of the coarse cementite throughout the repeated forging steps and to the influence of existing textured cementite on the nucleation of new cementite during cooling.

36 MATERIALS SCIENCE↗

Relationship between laser energy input, microstructures and magnetic properties of selective laser melted Fe-6.9%wt Si soft magnets

Highlights: • Effect of laser energy input on magnetic properties of SLM Fe-6.9%wt.Si is described; • Magnetic properties can be described as function of as-built microstructure after stress-relief post-treatment; • Samples with density >99% and strong crystallographic texture along BD have the best magnetic properties; • At very high laser energy, a strong cube texture forms that deteriorates the magnetic properties. - Abstract: Selective Laser Melting (SLM), a powder-bed Additive Manufacturing technology, can be used in combination with high temperature post-annealing to produce high-silicon steel parts characterised by quasi-static magnetic properties comparable to those of commercial electrical steel. However, the role of the as-built microstructure on the magnetic properties is still unexplored. Therefore, in this study the effect of the energy input of the processing laser on the magnetic properties of the material is investigated. The magnetic properties are determined for 4 mm-high rings obtained using three laser energy input values that provide a good compromise in terms of porosity and crack formation. The best magnetic properties are obtained for the rings built using a value of energy input that produces a strong fibrous crystallographic texture, in which one of the crystallographic <001> axes is preferentially aligned along the build direction. Whether the magnetic properties change with sample direction as a result of the crystallographic texture will be the subject of future research.

36 MATERIALS SCIENCE↗

Simultaneously improving mechanical properties and corrosion resistance of pure Ti by continuous ECAP plus short-duration annealing

Highlights: • Additional short-time annealing led to enhanced strength of UFG Ti due to texture strengthening. • UFG Ti showed improved corrosion resistance in artificial seawater compared with initial CG Ti. • Short-duration annealing enhanced corrosion resistance of UFG Ti due to stronger basal texture. - Abstract: This work investigated the effect of short-duration annealing on mechanical properties and corrosion behavior of bulk ultrafine-grained (UFG) pure Ti (grade 2) produced by high-efficiency equal-channel angular pressing (ECAP), serving the fast developing of marine industries. The initial coarse-grained (CG) Ti achieved higher strength after continuous ECAP at 420 °C for 4 passes, while additional short-duration annealing at 300 °C for 15 min of UFG Ti further led to extraordinary improvement of strength, which was associated with texture strengthening. The yield strength was increased from 362 MPa in as-received state to 561 MPa in post-ECAP annealed condition, and ultimate tensile strength from 450 MPa to 663 MPa. The ECAP-processed UFG Ti had better corrosion resistance in artificial seawater than the initial CG Ti. Short-duration annealing further improved the corrosion resistance of UFG Ti, which was related to stronger basal texture. The corrosion current density decreased from 68.37 nA cm{sup −2} for CG Ti in as-received condition to 41.77 nA cm{sup −2} for UFG Ti processed by ECAP plus short-duration annealing. The fraction of TiO{sub 2} within the surface oxide film for the post-ECAP annealed sample was increased. The bulk UFG Ti after post-ECAP short-duration annealing revealed an excellent combination of high strength, good ductility and superior corrosion resistance for marine applications.

36 MATERIALS SCIENCE↗

In situ monitoring of dislocation, twinning, and detwinning modes in an extruded magnesium alloy under cyclic loading conditions

This work investigates the microscopic deformation mechanisms of an extruded, precipitation-strengthened AZ80 magnesium (Mg) alloy subjected to strain-controlled low-cycle fatigue using in situ neutron diffraction measurements. Results demonstrate that the plastic deformation during cyclic loading is dominated by the alternating {10.2} extension twinning and detwinning mechanisms. The observed deformation mode is strongly texture and precipitate dependent. For the initial texture, the tested material has two major texture components which result in the occurrence of extension twinning during both compression and reverse tension in the first two cycles. The prolonged detwinning process in the following cycles is proposed to relieve the shear stress field of {00.2} grains, leading to the disappearance of twinning. The precipitation strengthening results in an increase of the critical resolved shear stress (CRSS) by similar to 33 MPa for the extension twinning in this AZ80 alloy. Here, the synergistic effects of the initial texture, precipitation strengthening, and load sharing of various grain families and phases contribute to the complicated evolution of dominant deformation mechanisms, among which elevated dislocation activities are believed to be responsible for the relatively poor low-cycle-fatigue lifetime when compared to other Mg alloys.

36 MATERIALS SCIENCE↗