Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

The computation of the post-stall behavior of a circulation controlled airfoil

The physics of the circulation controlled airfoil is complex and poorly understood, particularly with regards to jet stall, which is the eventual breakdown of lift augmentation by the jet at some sufficiently high blowing rate. The present paper describes the numerical simulation of stalled and unstalled flows over a two-dimensional circulation controlled airfoil using a fully implicit Navier-Stokes code, and the comparison with experimental results. Mach numbers of 0.3 and 0.5 and jet total to freestream pressure ratios of 1.4 and 1.8 are investigated. The Baldwin-Lomax and k-epsilon turbulence models are used, each modified to include the effect of strong streamline curvature. The numerical solutions of the post-stall circulation controlled airfoil show a highly regular unsteady periodic flowfield. This is the result of an alternation between adverse pressure gradient and shock induced separation of the boundary layer on the airfoil trailing edge.

Linton, Samuel W.↗

An experimental study of wall adaptation and interference assessment using Cauchy integral formula

This paper summarizes the results of an experimental study of combined wall adaptation and residual interference assessment using the Cauchy integral formula. The experiments were conducted on a supercritical airfoil model in the Langley 0.3-m Transonic Cryogenic Tunnel solid flexible wall test section. The ratio of model chord to test section height was about 0.7. The method worked satisfactorily in reducing the blockage interference and demonstrated the primary requirement for correcting for the blockage effects at high model incidences to correctly determine high lift characteristics. The studies show that the method has potential for reducing the residual interference to considerably low levels. However, corrections to blockage and upwash velocities gradients may still be required for the final adapted wall shapes.

Murthy, A. V.↗

Analysis of the surface load and radiated sound of a vibrating airfoil with application to the experiment of Brooks

A method is developed for calculating the surface load and radiated sound from a vibrating surface in a compressible viscous fluid. The method is applied to a thin two-dimensional elliptic cross-section. For large values of the viscous diffusion parameter, the surface load tends to an elliptic distribution in agreement with the results of inviscid theory when edge pressure continuity is enforced. For thin surfaces, the surface load is insensitive to variations in the thickness ratio. A three-dimensional spectral technique is developed to calculate the inviscid surface load and radiated sound from a thin vibrating airfoil. The inviscid theory predicts the correct form of the far field sound pressure and its phase. The actual levels are somewhat sensitive to the choice of theoretical spanwise surface pressure mode but are in better agreement with the experiment than the surface pressure. The comparison of theoretical and experimental surface pressure indicates that the viscous theory, used to validate the inviscid theory, is either inadequate or there is a source of experimental error.

Yates, J. E.↗

An analytical evaluation of airfoil sections for helicopter rotor applications

An analytical technique was used to evaluate airfoils for helicopter rotor application. This technique permits assessment of the influences of airfoil geometric variations on drag divergence Mach number at lift coefficients from near zero to near maximum lift. Analytical results presented in this paper indicate the compromises in drag divergence Mach number which result from changes in (1) thickness ratio, (2) location of maximum thickness, (3) leading-edge radius, (4) camber addition, and (5) location of maximum camber of NACA four- and five-digit-series airfoils and some 6-series airfoils of potential interest for helicopters. Examples of airfoil sections which combine several of the geometric changes favorable to both advancing and retreating section performance have been presented.

Bingham, G. J.↗

PROFILE: Airfoil Geometry Manipulation and Display

This report provides user information for program PROFILE, an aerodynamics design utility for plotting, tabulating, and manipulating airfoil profiles. A dozen main functions are available. The theory and implementation details for two of the more complex options are also presented. These are the REFINE option, for smoothing curvature in selected regions while retaining or seeking some specified thickness ratio, and the OPTIMIZE option, which seeks a specified curvature distribution. Use of programs QPLOT and BPLOT is also described, since all of the plots provided by PROFILE (airfoil coordinates, curvature distributions, pressure distributions)) are achieved via the general-purpose QPLOT utility. BPLOT illustrates (again, via QPLOT) the shape functions used by two of PROFILE's options. These three utilities should be distributed as one package. They were designed and implemented for the Applied Aerodynamics Branch at NASA Ames Research Center, Moffett Field, California. They are all written in FORTRAN 77 and run on DEC and SGI systems under OpenVMS and IRIX.

Collins, Leslie↗

An analytical and experimental evaluation of airfoil sections for helicopter rotor application

The influence of the more independent airfoil parameters such as thickness, thickness distribution, leading-edge radius, camber, and camber distribution on lift-Mach number characteristics is investigated at lift coefficients up to near-maximum lift. The analysis is based on the drag divergence Mach number (Md) prediction techniques, where Md is the free-stream Mach number at which the rate of increase of drag coefficient with Mach number equals 0.1. The analytical results obtained indicate the compromises in Md which result from changes in thickness ratio, location of maximum thickness, leading edge radius, camber addition, and location of maximum camber for four- and five-digit airfoils and some six-series airfoils of potential interest for helicopters. An example of airfoil sections which combines several of the favorable geometric changes is evaluated analytically and experimentally. A comparison of results shows that the relative effect of the geometric changes on the lift coefficient-Md relation is realistic, and that the methods of analysis employed can be effectively used during preliminary vehicle design and airfoil selection.

Bingham, G. J.↗

Experience with some repeat tests on the 9 inch chord CAST-10-2/DOA 2 airfoil model in the Langley 0.3-m TCT adaptive wall test section

A co-operative testing program is in progress between the Langley Research Center (NASA) and the National Aeronautical Establishment (NAE, Canada) to validate two different techniques of airfoil testing at transonic speeds. The procedure employed is to test the same airfoil model in the NAE two-dimensional tunnel and the Langley 0.3-m Transonic Cryogenic Tunnel (0.3-m TCT). The airfoil model used in testing was CAST-10-2/DOA-2 super-critical airfoil. The Langley 0.3-m TCT has a relatively small cross section of 13 in x 13 in, giving a (h/c) ratio of 1.44 for the same 9 in chord model. The approach employed in the 0.3-m TCT aims towards eliminating the wall effects by using active walls. The top and bottom walls are flexible. By changing the wall shapes during a test in an iterative manner, the wall interference effects are reduced. The method employed to change the wall shapes is the adaptive wall technique. The current test program provided an opportunity to validate the adaptive wall technique in the 0.3-m TCT. The relatively long chord airfoil represents a severe test case to test the efficacy of the adaptive wall technique under cryogenic conditions. The program also involved removal of side wall boundary-layer thus increasing the complexity of the wall adaptation technique. This paper deals with some salient results obtained regarding repeatability of test data and possible residual interference effects.

Murthy, A. V.↗

Comparison of supercritical and conventional wing flutter characteristics

A wind-tunnel study was undertaken to directly compare the measured flutter boundaries of two dynamically similar aeroelastic models which had the same planform, maximum thickness-to-chord ratio, and as nearly identical stiffness and mass distributions as possible, with one wing having a supercritical airfoil and the other a conventional airfoil. The considerations and problems associated with flutter testing supercritical wing models at or near design lift coefficients are discussed, and the measured transonic boundaries of the two wings are compared with boundaries calculated with a subsonic lifting surface theory.

Farmer, M. G.↗

Computer modeling of fan-exit-splitter spacing effects on F100 response to distortion

The distortion response of the F100(3) engine was effected by the fan exit splitter configuration. The sensitivity for a proximate splitter fan is calculated to be slightly greater than a remote splitter configuration with identical airfoils. Predicted response was based upon a multiple segment parallel compressor Model modified to include a bypass ratio representation that effects the performance characteristics of the last rotor and intermediate case struts. The predicted distortion response required an accurate definition of row pre- and post-stall undistorted operation.

Shaw, M.↗

Scale–Resolving Simulations of a Fundamental Trailing–Edge Cooling Slot Using a Discontinuous–Galerkin Spectral–Element Method

The accurate prediction of turbulent mixing in high-pressure turbines that incorporate various airfoil surface-cooling strategies is becoming increasing critical to the design of modern gas turbine engines where the quest for improved efficiency is driving compressor overall pressure ratios and turbine inlet temperatures to much higher levels than ever before. In the present paper, a recently developed computational capability for accurate and efficient scale–resolving simulations of turbomachinery is extended to study the turbulent mixing mechanism of a simplified abstraction of an airfoil trailing-edge cooling slot - a plane wall jet with finite lip thickness discharging into an ambient flow. The computational capability is based on an entropy– stable, discontinuous–Galerkin approach that extends to arbitrarily high orders of spatial and temporal accuracy. The numerical results show that the present simulations capture the trends observed in the experiments. Discrepancies between the simulations and experiments are believed to be due to differences in the inflow profiles and tunnel side–wall effects. The thick lip configuration leads to a thicker wake and higher unsteadiness in the wall jet compared to the thin lip. A detailed comparison of the turbulent flowfields is presented to highlight differences arising due to lip thickness variations.

Scale Resolving↗

Dynamic Stall Measurements and Computations for a VR-12 Airfoil with a Variable Droop Leading Edge

High density-altitude operations of helicopters with advanced performance and maneuver capabilities have lead to fundamental research on active high-lift system concepts for rotor blades. The requirement for this type of system was to improve the sectional lift-to-drag ratio by alleviating dynamic stall on the retreating blade while simultaneously reducing the transonic drag rise of the advancing blade. Both measured and computational results showed that a Variable Droop Leading Edge (VDLE) airfoil is a viable concept for application to a rotor high-lift system. Results are presented for a series of 2D compressible dynamic stall wind tunnel tests with supporting CFD results for selected test cases. These measurements and computations show a dramatic decrease in the drag and pitching moment associated with severe dynamic stall when the VDLE concept is applied to the Boeing VR-12 airfoil. Test results also show an elimination of the negative pitch damping observed in the baseline moment hysteresis curves.

Martin, P. B.↗

Wind Tunnel Evaluation of a Model Helicopter Main-Rotor Blade With Slotted Airfoils at the Tip

Data for rotors using unconventional airfoils are of interest to permit an evaluation of this technology's capability to meet the U.S. Army's need for increased helicopter mission effectiveness and improved safety and survivability. Thus, an experimental investigation was conducted in the Langley Transonic Dynamics Tunnel (TDT) to evaluate the effect of using slotted airfoils in the rotor blade tip region (85 to 100 percent radius) on rotor aerodynamic performance and loads. Four rotor configurations were tested in forward flight at advance ratios from 0.15 to 0.45 and in hover in-ground effect. The hover tip Mach number was 0.627, which is representative of a design point of 4000-ft geometric altitude and a temperature of 95 F. The baseline rotor configuration had a conventional single-element airfoil in the tip region. A second rotor configuration had a forward-slotted airfoil with a -6 deg slat, a third configuration had a forward-slotted airfoil with a -10 slat, and a fourth configuration had an aft-slotted airfoil with a 3 deg flap (trailing edge down). The results of this investigation indicate that the -6 deg slat configuration offers some performance and loads benefits over the other three configurations.

Noonan, Kevin W.↗

Aerodynamic characteristics of three helicopter rotor airfoil sections at Reynolds number from model scale to full scale at Mach numbers from 0.35 to 0.90

An investigation was conducted in the Langely 6 by 28 inch transonic tunnel to determine the two dimensional aerodynamic characteristics of three helicopter rotor airfoils at Reynolds numbers from typical model scale to full scale at Mach numbers from about 0.35 to 0.90. The model scale Reynolds numbers ranged from about 700,00 to 1,500,000 and the full scale Reynolds numbers ranged from about 3,000,000 to 6,600,000. The airfoils tested were the NACA 0012 (0 deg Tab), the SC 1095 R8, and the SC 1095. Both the SC 1095 and the SC 1095 R8 airfoils had trailing edge tabs. The results of this investigation indicate that Reynolds number effects can be significant on the maximum normal force coefficient and all drag related parameters; namely, drag at zero normal force, maximum normal force drag ratio, and drag divergence Mach number. The increments in these parameters at a given Mach number owing to the model scale to full scale Reynolds number change are different for each of the airfoils.

Noonan, K. W.↗

Comparison of supercritical and conventional wing flutter characteristics

A wind-tunnel study is described in which it was attempted to compare the measured flutter boundaries of two dynamically similar aeroelastic models with identical planform, maximum thickness-to-chord ratio, and as nearly identical stiffness and mass distributions as possible, but with one wing having a supercritical airfoil and the other a conventional one. At subsonic Mach numbers, the flutter boundary for the supercritical wing was above that of the conventional wing, as predicted by flutter calculations using subsonic lifting theory. In the transonic region, however, the supercritical wing boundary decreases more rapidly and the minimum flutter point occurs at a dynamic pressure below the conventional wing boundary. Airfoil shape effects may account for some of the difference in the flutter boundaries of the two airfoils.

Farmer, M. G.↗

Suppression of dynamic stall with a leading-edge slat on a VR-7 airfoil

The VR-7 airfoil was experimentally studied with and without a leading-edge slat at fixed angles of attack from 0 deg to 30 deg at Re = 200,000 and for unsteady pitching motions described by alpha equals alpha(sub m) + 10 deg(sin(wt)). The models were two dimensional, and the test was performed in a water tunnel at Ames Research Center. The unsteady conditions ranged over Re equals 100,000 to 250,000, k equals 0.001 to 0.2, and alpha(sub m) = 10 deg to 20 deg. Unsteady lift, drag, and pitching-moment measurements were obtained along with fluorescent-dye flow visualizations. The addition of the slat was found to delay the static-drag and static-moment stall by about 5 degrees and to eliminate completely the development of a dynamic-stall vortex during unsteady motions that reached angles as high as 25 degrees. In all of the unsteady cases studied, the slat caused a significant reduction in the force and moment hysteresis amplitudes. The reduced frequency was found to have the greatest effect on the results, whereas the Reynolds number had little effect on the behavior of either the basic or the slatted airfoil. The slat caused a slight drag penalty at low angles of attack, but generally increased the lift/drag ratio when averaged over the full cycle of oscillation.

Mcalister, K. W.↗

Sensitivity of lag-damping correlations to structural and aerodynamic approximations of isolated experimental rotors in forward flight

The predictions of regressive lag-mode damping levels are correlated with the database of an isolated, soft-inplane, three-blade rotor operated untrimmed. The database was generated at the Army Aeroflightdynamics Directorate at Ames. The correlation covers a broad range of data, from near-zero thrust conditions in hover to high-thrust and highly stalled conditions in forward flight with advance ratio as high as 0.55 and shaft angle as high as 20 degrees. In the experimental rotor, the airfoil or blade portion has essentially uniform mass and stiffness distributions, but the root flexure has highly nonuniform mass and stiffness distributions. Accordingly, the structural approximations refer to four models of root-flexure-blade assembly. They range from a rigid flap-lag model to three elastic flap-lag-torsion models, which differ in modeling the root flexure. The three models of root-flexure are: three root springs in which the bending-torsion couplings are fully accounted for; a finite-length beam element with some average mass and stiffness distributions such that the fundamental frequencies match those of the experimental model; and accurate modal representation in which the actual mass and stiffness distributions of the experimental root-flexure-blade assembly are used in calculating the nonrotating mode shapes. The four models of root-flexure-blade assembly are referred to as the rigid flap-lag model, spring model, modified model and modal model. For each of these four models of the root-flexure-blade assembly, the predictions are based on the following five aerodynamic theories: ear theory, which accounts for large angle-of-attack and reverse-flow effects on lift, and has constant drag and pitching moment; quasisteady stall theory, which includes quasisteady stall lift, drag and pitching moment characteristics of the airfoil section, dynamics stall theory, which uses the ONERA dynamic stall models of lift, drag and pitching moment; dynamic wake theory, which is based on a finite-state three-dimensional wake model and includes all wake effects including both shed and trailing vorticity; and dynamics and wake theory, which combines both dynamic stall theory and dynamic wake theory and is a relatively complete aerodynamic representation.

Gaonkar, G. H.↗

Two stage turbine for rockets

The aerodynamic design and rig test evaluation of a small counter-rotating turbine system is described. The advanced turbine airfoils were designed and tested by Pratt & Whitney. The technology represented by this turbine is being developed for a turbopump to be used in an advanced upper stage rocket engine. The advanced engine will use a hydrogen expander cycle and achieve high performance through efficient combustion of hydrogen/oxygen propellants, high combustion pressure, and high area ratio exhaust nozzle expansion. Engine performance goals require that the turbopump drive turbines achieve high efficiency at low gas flow rates. The low mass flow rates and high operating pressures result in very small airfoil heights and diameters. The high efficiency and small size requirements present a challenging turbine design problem. The shrouded axial turbine blades are 50 percent reaction with a maximum thickness to chord ratio near 1. At 6 deg from the tangential direction, the nozzle and blade exit flow angles are well below the traditional design minimum limits. The blade turning angle of 160 deg also exceeds the maximum limits used in traditional turbine designs.

Veres, Joseph P.↗

Computerized three-dimensional aerodynamic design of a lifting rotor blade

A three-dimensional, inviscid, full-potential lifting rotor code was used to demonstrate that pressure distributions on both advancing and retreating blades could be significantly improved by perturbing local airfoil sections. The perturbations were described by simple geometric shape functions. To illustrate the procedure, an example calculation was made at a forward flight speed of 85 m/sec (165 knots) and an advance ratio of 0.385. It was found that a minimum of three shape functions was required to improve the pressures without producing undesirable secondary effects in high-speed forward flight on a hypothetical modern rotor blade initially having an NLR-1 supercritical airfoil. Reductions in the shock strength on the advancing blade could be achieved, while simultaneously lessening leading-edge pressure gradients on the retreating blade. The major blade section modifications required were blunting of the upper surface leading edge and some reshaping of the blade's upper surface resulting in moderately thicker airfoils.

Tauber, M. E.↗