Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS - CASCADES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

162 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 7 - Raw Data

Sequence 7: Shroud Operating (P) This test sequence used a downwind, rigid turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Turntable angles from 0° to 30° were achieved, but the yaw error angle was maintained at 0° by adjusting the nacelle yaw. The blade tip pitch was 3°. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. An airfoil-shaped aluminum shroud was placed on the tower below the 34% span five-hole probe. It extended below the 91% span five-hole probe. The turntable angle was adjusted to position the shroud at various angles relative to the flow, but the turbine yaw error angle was maintained at 0°. Two additional points were collected where the turntable angle was 0°, and the turbine yaw angle was 20° (71000200) or -20° (710M0200).

17 WIND ENERGY↗
DOE OSTI2023

HLPW-4/GMGW-3: High-Order Discretization Technology Focus Group Workshop Summary

This paper summarizes the High-Order Technical Focus Group (HO-TFG) submissions for the joint 4th AIAA High Lift Prediction (HLPW-4) and 3rd Geometry and Mesh Generation Workshop (GMGW-3). The goal of the workshop was to assess the state-of-the-art in mesh generation and computational fluid dynamics software. The Common Research Model High-Lift (CRM-HL) variant served as the primary focus of the workshop, and a two-dimensional airfoil section from the CRM-HL was used as a verification test case. Here, the HO-TFG was tasked with generating high-order curved meshes for both geometries, and computing high-order solutions using both Reynolds-averaged Navier–Stokes and scale-resolving formulations. While limited by computational resources, the final results demonstrate the potential of higher-order methods to increase solution accuracy with a lower degree-of-freedom count relative to second-order discretizations.

42 ENGINEERING↗
DOE OSTI2020

Koopman-Based Approach to Nonintrusive Reduced Order Modeling: Application to Aerodynamic Shape Optimization and Uncertainty Propagation

A methodology for nonintrusive projection-based nonlinear model reduction originally presented by Renganathan et al. is further extended here toward parametric systems with a focus on application to aerospace design. Specifically, the method is extended to address static systems with parametric geometry (that deforms the mesh) in addition to parametric freestream boundary conditions. The main idea is to first perform a transformation on the governing equations such that it is lifted to a higher-dimensional but linear underdetermined system. This enables one to extract the system matrices easily as compared to that of the original nonlinear system. The underdetermined system is closed with a set of model-dependent nonlinear constraints upon which the model reduction is finally performed. The methodology is validated on the subsonic and transonic inviscid flows past the NACA0012 and the RAE2822 airfoils with parametrized shapes. The utility of the approach is further demonstrated by applying it to two common problems in aerospace design, namely, derivative-free global optimization and parametric uncertainty quantification with Monte Carlo sampling. Overall, the methodology is shown to achieve accuracy up to 5% and computational speedup of two to three orders of magnitude relative to the full order model. Comparison against another nonintrusive model reduction method revealed that the proposed approach is more robust, accurate, and retains the consistency between the state variables.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

HLPW-4/GMGW-3: High Order Discretization Technology Focus Group Workshop Summary

This paper summarizes the High-Order Technical Focus Group (HO-TFG) submissions for the joint 4th AIAA High Lift Prediction and 3rd Geometry and Mesh Generation Workshop. The goal of the workshop was to assess the state-of-the-art in mesh generation and computational fluid dynamics software. The Common Research Model High-Lift (CRM-HL) variant served as the primary focus of the workshop, and a 2D airfoil section from the CRM-HL was used as a verification test case. The HO-TFG was tasked with generating high-order curved meshes for both geometries, and computing high-order solutions using both Reynolds Averaged Navier-Stokes and scale resolving formulations. While limited by computational resources, the final results demonstrate the potential of higher-order methods to increase solution accuracy with a lower degree of freedom count relative to second-order discretizations.

Galbraith, Marshall C.↗
DOE OSTI2024

Comparison of Full-Field and Integrated CFD Convergence Based on Richardson Extrapolation

This work investigated the usefulness of Richardson extrapolation--based discretization error estimates across all points in a solution field to produce a spatial convergence field for a computational fluid dynamics (CFD) simulation. The presented work used previously developed methods for Richardson extrapolation to compute the convergence orders of a CFD simulation at all points of the base (coarsest) mesh solution. Three test cases of increasing complexity were considered: Poiseuille flow, incompressible flow around a sharp corner, and transonic flow over an RAE 2822 airfoil. These test cases highlighted the potential of the proposed method to identify error sources and their relation to the model system-response-quantity convergence orders. However, these test cases also revealed the immaturity of the proposed method stemming from the unreliability of computing observed convergence orders at single points. Nonetheless, the test cases highlighted that the observed convergence orders allow for a more accurate diagnosis of constructive and destructive error transport than mesh pair error estimates. In the long run, the proposed method can be a tool for developing efficient and advanced error management strategies like adaptive mesh refinement.

Weinmeister, Justin↗
DOE OSTI2026

High-Fidelity, Low-Dissipation/Symmetry-Preserving Numerical Scheme for Solving the Euler Equations with Unstructured, Metric-Based Mesh Adaptation

This work presents an overview of a high-fidelity compressible Euler solver that utilizes the continuous Galerkin (CG) method with added artificial numerical diffusion for stabilization to solve a variety of unsteady and steady benchmark inviscid flow problems. This work shows that discretizing the Euler equations with this CG approach and first order basis functions produces a cost-effective stencil as well as simple well-posed boundary conditions. We show through convergence testing with manufactured solutions that the reduced stencil of CG, combined with the low amount of artificial diffusion required when using the stabilization method outlined in this work, leads to stable and highly accurate results for a variety of unsteady and steady applications. When combined with the adaptive mesh refinement approach used for many of the cases in this work, our results show that the flow solver achieves even more accurate results. A variety of inviscid flow cases are presented in this work, including transient 2D cases with complex shock structures and several steady 3D airfoils sections with a constant span.

Doetsch, Kevin [ORNL] (ORCID:0000000267051705)↗
DOE OSTI2023

OC6 project Phase III: validation of the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure

Abstract. This paper provides a summary of the work done within Phase III of the Offshore Code Comparison Collaboration, Continued, with Correlation and unCertainty (OC6) project, under the International Energy Agency Wind Technology Collaboration Programme Task 30. This phase focused on validating the aerodynamic loading on a wind turbine rotor undergoing large motion caused by a floating support structure. Numerical models of the Technical University of Denmark 10 MW reference wind turbine were validated using measurement data from a 1:75 scale test performed during the UNsteady Aerodynamics for FLOating Wind (UNAFLOW) project and a follow-on experimental campaign, both performed at the Politecnico di Milano wind tunnel. Validation of the models was performed by comparing the loads for steady (fixed platform) and unsteady (harmonic motion of the platform) wind conditions. For the unsteady wind conditions, the platform was forced to oscillate in the surge and pitch directions under several frequencies and amplitudes. These oscillations result in a wind variation that impacts the rotor loads (e.g., thrust and torque). For the conditions studied in these tests, the system aerodynamic response was almost steady. Only a small hysteresis in airfoil performance undergoing angle of attack variations in attached flow was observed. During the experiments, the rotor speed and blade pitch angle were held constant. However, in real wind turbine operating conditions, the surge and pitch variations would result in rotor speed variations and/or blade pitch actuations, depending on the wind turbine controller region that the system is operating. Additional simulations with these control parameters were conducted to verify the fidelity of different models. Participant results showed, in general, a good agreement with the experimental measurements and the need to account for dynamic inflow when there are changes in the flow conditions due to the rotor speed variations or blade pitch actuations in response to surge and pitch motion. Numerical models not accounting for dynamic inflow effects predicted rotor loads that were 9 % lower in amplitude during rotor speed variations and 18 % higher in amplitude during blade pitch actuations.

17 WIND ENERGY↗
DOE OSTI2020

Numerical study of heat transfer enhancement in laminar and turbulent flow in enhanced tubes with uniform and non-uniform thermal boundary conditions

Various types of tube enhancements have been proposed in order to increase heat transfer while minimizing any associated increases in pressure drop. This paper presents a numerical study of two different types of enhanced tubes: the relatively common twisted tape insert tube, and a novel tube with airfoil shaped pins on the inner surface. Each tube is studied in both the laminar and turbulent flow regime. In addition to the typical constant temperature and constant flux boundary conditions, a non-constant heat flux boundary condition is applied on one half of the tube, a situation which may be encountered when absorbing solar radiation. In general, each type of enhanced tube offers a thermal performance factor greater than unity at certain Re. In addition, the non-uniform heat flux boundary condition appears to function similarly as the uniform heat flux boundary condition.

Sandlin, Matthew J.↗
DOE OSTI2022

Damping coating with a constraint layer

A coating is applied to a base material. The coating comprises a viscoelastic layer having a surface in which cavities are formed; and a constraint layer. The viscoelastic layer is disposed on the base material, and the constraint layer is disposed on, and partially bonded, at an interface, to the viscoelastic layer over the surface in which the cavities are formed. The cavities are filled with particles configured for vibration and frictional interaction at the partially bonded interface between the partially bonded viscoelastic layer and the constraint layer. A turbine blade having an airfoil with the subject coating is also provided.

Zhang, James↗
DOE OSTI2024

Numerical study of heat transfer enhancement in laminar and turbulent flow in enhanced tubes with uniform and non-uniform thermal boundary conditions

Various types of tube enhancements have been proposed in order to increase heat transfer while minimizing any associated increases in pressure drop. This paper presents a numerical study of two different types of enhanced tubes: the relatively common twisted tape insert tube, and a novel tube with airfoil shaped pins on the inner surface. Each tube is studied in both the laminar and turbulent flow regime. In addition to the typical constant temperature and constant flux boundary conditions, a non-constant heat flux boundary condition is applied on one half of the tube, a situation which may be encountered when absorbing solar radiation. In general, each type of enhanced tube offers a thermal performance factor greater than unity at certain Re. In addition, the non-uniform heat flux boundary condition appears to function similarly as the uniform heat flux boundary condition.

Sandlin, M↗
DOE OSTI2024

The Experimental and Numerical Investigation of Internal Heat Transfer for Supercritical Carbon Dioxide Cooling in a Staggered Pin Fin Array and Single-Jet Impingement

Over the past decade, the drive to reduce greenhouse gas emissions and to increase thermal efficiency for turbomachinery has invigorated the application of supercritical carbon dioxide (sCO2) power cycles for energy generation. Compared to the industry standard air cycles, sCO2 applications hold the potential for several advantages, including higher efficiencies, smaller footprints, and zero greenhouse gas emissions. However, like any turbomachinery application, the turbine inlet temperature must increase to increase thermal efficiency. This introduces the need for internal cooling features to avoid material failure as operating conditions rise. Two standard features include pin fin turbulators in the trailing edge and jet impingement in the airfoil's leading edge. Over the past several decades, these features have been the subject of extensive research. However, the move to the sCO2 operating environment creates the need to re-visit these features to quantify the heat transfer capabilities within this supercritical cooling environment. The first objective of this paper is to discuss the development of the experimental demonstration for internal heat transfer testing at 200 bar and 400 Celsius, which sits well within the CO2 supercritical region. Next, the heat transfer for pin fin turbulators and single-jet impingement in the sCO2 environment is compared to existing air data-derived correlations to quantify any deviations from literature correlations. Finally, the experimental process aims to validate internal cooling conjugate heat transfer numerical simulations for sCO2 turbines.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Design and Cooling Performance of Additively Manufactured Ceramic Turbine Vanes

Ceramic materials are of significant interest in aviation and power generation gas turbine engines due to their low density and ability to withstand high temperatures. Increased cycle thermal efficiency and higher specific power output is possible by incorporating ceramic components that enable high turbine inlet temperatures and lower required cooling airflow levels. However, ceramics can be difficult and costly to form into the complex shapes used in gas turbine components, often requiring specialized multi-step processes. Furthermore, ceramic components in the hottest areas of a gas turbine, such as vanes or blade shroud seals, will still likely require cooling which is challenging to implement in conventional ceramic manufacturing approaches. Therefore, this study presents a multidisciplinary approach that investigates the design, fabrication, and overall cooling effectiveness evaluation of additively manufactured (AM), polymer derived ceramic (PDC) turbine vanes. A thermo-mechanically optimized vane design was generated, ceramic additive manufacturing of the complex cooling configuration was developed, and quantification of the increase in overall cooling effectiveness was performed in a 1X scale, high-speed facility using infrared thermography. This study produced a PDC AM process, capable of printing complex internal cooling schemes in 1X scale turbine vanes. Furthermore, it was found that the optimized vane more than doubled the overall cooling effectiveness observed in the baseline design, which reasonably agreed with thermomechanical optimization model predictions. Additionally, the optimized ceramic vane outperformed an identical metal vane, in terms of area averaged cooling effectiveness, suggesting that the ceramic vane could operate at reduced coolant flowrates to achieve comparable levels of cooling performance.

Reynolds number↗
DOE OSTI2021

Design of high-deflection foils MHK applications - CFD models - RivGen turbine

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. CFD Models OpenFOAM V1912 RivGen turbine

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Design of high-deflection foils MHK applications - FEA models - RivGen Turbines

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. FEA models - NASTRAN Baseline RivGen turbine Proposed new design

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Design of high-deflection foils MHK applications - CFD models - Helical turbines

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. CFD models of helical model scale turbines tested at UNH OpenFOAM v1912 Tip Speed Ratio (TSR) = 3.00 Different strut configurations

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Design of high-deflection foils MHK applications - FEA models - Helical turbines

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. FEA models - NASTRAN Helical foil turbines tested at UNH tow tank Glass and carbon composite material properties Loads derived from CFD models

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Design of High-Deflection Foils MHK Applications - FEA models

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. Finite element models - NASTRAN files Model scale turbines tested in UNH tow tank Model loads from CFD models

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Design of high deflection foils for MHK applications - CFD files

The Ocean Renewable Power Company's (ORPC's) goal is to design, develop, and test hydrofoils with large deflections. The effects of the deflections on cross-flow turbine performance would be evaluated in order to inform design considerations for full-scale water turbines and other marine hydrokinetic devices. OpenFOAM V1912 files for straight foil model scale turbines in the University of New Hampshire tow tank. Strut Locations = (0.13, 0.225, 0.450, 0.675, 0.900) [m] Tip speed ratio = 2.40

16 TIDAL AND WAVE POWER↗