Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALUMINATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Effect of aluminum substitution on the reflectance spectra of hematite

Hematite and aluminous hematite were synthesized and the diffuse reflectance spectra were recorded for the region between 0.35 and 1.20 microns. Results show that the near-IR based minimum for the aluminous hematite is shifted longward by about 0.02 microns and is much more shallow. Also, the aluminous specimen is considerably more reflective shortward of approximately 0.55 microns where the ferritic specimen is strongly absorbing. This is noteworthy since the visible slope and the red shoulder are often used in the construction of false color and band ratio images.

Morris, R. V.↗
NASA NTRS1989

A slow positron beam generator for lifetime studies

A slow positron beam generator using well-annealed polycrystalline tungsten moderators and a Na-22 positron source was developed. A 250 micro c source, deposited on a 2.54 micron thick aluminized mylar, is sandwiched between two (2.54 cm x 2.54 cm x 0.0127 cm) tungsten pieces. Two (2.54 cm x 2.54 cm x t cm) test polymer films insulate the two tungsten moderator pieces from the aluminized mylar source holder (t=0.00127 to 0.0127). A potential difference of 10 to 100 volts--depending on the test polymer film thickness (t)--is applied between the tungsten pieces and the source foil. Thermalized positrons diffusing out of the moderator pieces are attracted to the source foil held at an appropriate potential below the moderator pieces. These positrons have to pass through the test polymer films before they can reach the source foil. The potential difference between the moderator pieces and the aluminized mylar is so adjusted as to force the positrons to stop in the test polymer films. Thus the new generator becomes an effective source of positrons for assaying thin polymer films for their molecular morphology.

Singh, Jag J.↗
NASA NTRS2002

Vacuum Ultraviolet Radiation and Atomic Oxygen Durability Evaluation of HST Bi-Stem Thermal Shield Materials

Bellows-type thermal shields were used on the bi-stems of replacement solar arrays installed on the Hubble Space Telescope (HST) during the first HST servicing mission (SMI) in December 1993. These thermal shields helped reduce the problem of thermal gradient- induced jitter observed with the original HST solar arrays during orbital thermal cycling and have been in use on HST for eight years. This paper describes ground testing of the candidate solar array bi-stem thermal shield materials including backside aluminized Teflon(R)FEP (fluorinated ethylene propylene) with and without atomic oxygen (AO) and ultraviolet radiation protective surface coatings for durability to AO and combined AO and vacuum ultraviolet (VOV) radiation. NASA Glenn Research Center (GRC) conducted VUV and AO exposures of samples of candidate thermal shield materials at HST operational temperatures and pre- and post-exposure analyses as part of an overall program coordinated by NASA Goddard Space Flight Center (GSFC) to determine the on-orbit durability of these materials. Coating adhesion problems were observed for samples having the AO- and combined AO/UV-protective coatings. Coating lamination occurred with rapid thermal cycling testing which simulated orbital thermal cycling. This lack of adhesion caused production of coating flakes from the material that would have posed a serious risk to HST optics if the coated materials were used for the bi-stem thermal shields. No serious degradation was observed for the uncoated aluminized Teflon(R) as evaluated by optical microscopy, although atomic force microscopy (AFM) microhardness testing revealed that an embrittled surface layer formed on the uncoated Teflon(R) surface due to vacuum ultraviolet radiation exposure. This embrittled layer was not completely removed by AO erosion, No cracks or particle flakes were produced for the embrittled uncoated material upon exposure to VUV and AO at operational temperatures to an equivalent exposure of approximately five years in the HST environment. Uncoated aluminized FEP Teflon(R) was determined to be the most appropriate thermal shield material and was used on the bi-stems of replacement solar arrays installed on HST during SMI in December 1993. The SMI -installed solar arrays air scheduled to be replaced during MST's fourth servicing mission (SM3B) in early 2002.

Dever, Joyce↗
NASA NTRS1978

Wall Covering

The attractive wall covering shown below is one of 132 styles in the Mirror Magic II line offered by The General Tire & Rubber Company, Akron, Ohio. The material is metallized plastic fabric, a spinoff from space programs. Wall coverings are one of many consumer applications of aluminized plastic film technology developed for NASA by a firm later bought by King-Seeley Thermos Company, Winchester, Massachusetts, which now produces the material. The original NASA use was in the Echo 1 passive communications satellite, a "space baloon" made of aluminized mylar; the high reflectivity of the metallized coating enabled relay of communications signals from one Earth station to another by "bouncing" them off the satellite. The reflectivity feature also made the material an extremely efficient insulator and it was subsequently widely used in the Apollo program for such purposes as temperature control of spacecraft components and insulation of tanks for fuels that must be maintained at very low temperatures. I Used as a wall covering, the aluminized material offers extra insulation, reflects light and I resists cracking. In addition to General Tire, King-Seeley also supplies wall covering material to Columbus Coated Fabrics Division of Borden, Incorporated, Columbus, Ohio, among others.

Source record↗
NASA NTRS2003

High-Energy-Density Capacitors

Capacitors capable of storing energy at high densities are being developed for use in pulse-power circuits in such diverse systems as defibrillators, particle- beam accelerators, microwave sources, and weapons. Like typical previously developed energy-storage capacitors, these capacitors are made from pairs of metal/solid-dielectric laminated sheets that are wound and pressed into compact shapes to fit into cans, which are then filled with dielectric fluids. Indeed, these capacitors can be fabricated largely by conventional fabrication techniques. The main features that distinguish these capacitors from previously developed ones are improvements in (1) the selection of laminate materials, (2) the fabrication of the laminated sheets from these materials, and (3) the selection of dielectric fluids. In simplest terms, a high-performance laminated sheet of the type used in these capacitors is made by casting a dielectric polymer onto a sheet of aluminized kraft paper. The dielectric polymer is a siloxane polymer that has been modified with polar pendant groups to increase its permittivity and dielectric strength. Potentially, this polymer is capable of withstanding an energy density of 7.5 J/cm3, which is four times that of the previous state-of-the-art-capacitor dielectric film material. However, the full potential of this polymer cannot be realized at present because (1) at thicknesses needed for optimum performance (.8.0 m), the mechanical strength of a film of this polymer is insufficient for incorporation into a wound capacitor and (2) at greater thickness, the achievable energy density decreases because of a logarithmic decrease in dielectric strength with increasing thickness. The aluminized kraft paper provides the mechanical strength needed for processing of the laminate and fabrication of the capacitor, and the aluminum film serves as an electrode layer. Because part of the thickness of the dielectric is not occupied by the modified siloxane polymer, the achievable energy density must be somewhat less than the maximum value. The laminate is produced by a continuous film-casting process, using the machinery depicted schematically in the figure. The designs of the process and machinery are dictated partly by the fact that during the processing step prior to casting the polymer, the aluminized kraft paper becomes wet with water. Because the polymer resin to be cast is hydrophobic, the paper must be dried to make it possible to coat the paper uniformly, leaving no pinholes. Accordingly, an infrared heater is placed next to the paper feed roll to dry the paper prior to casting.

Slenes, Kirk↗
DOE OSTI2021

Towards ternary binders involving limestone additions — A review

The review summarises literature to examine the transition from portland limestone cement system to composite ternary binder systems involving limestone. Interest in limestone addition as an ideal component in multicomponent binder systems has surged as evident from the large volume of literature published in the recent past. A ternary blended system, with co-substitution of limestone, has the potential to complement the reaction of the supplementary cementitious materials (SCMs). The direct addition of limestone powder helps to attain higher substitution levels of portland cement clinker, improve early age properties, and supplement SCM's reactivity. However, the dilution of hydrates could hamper the long-term benefits. In this review, the interaction of fine limestone is classified and elaborated under two broad umbrellas: physical and chemical interactions. The physical interactions can manifest in three ways, namely, filler action, shearing action and improved packing, which alters reaction rate and extent at early ages. The chemical interactions also modify the reaction kinetics and phase assemblage due to nucleation of C-S-H on calcite surfaces, preservation of the ettringite phase and formation of carboaluminates. Two different forms of carboaluminate hydrates — hemicarboaluminate and mono-carboaluminate can be present in the hydrate matrix depending on the balance between carbonate ions and aluminates in the pore solution. Several factors such as replacement level, particle size, choice of SCM, its reactivity and reactive aluminates content, sulphate levels, curing temperature, and duration of curing can control the carboaluminate formation, reaction degree of SCMs and chemical interaction from limestone additions. A combination of physical and chemical effects makes fine limestone a potential material for co-substitution with aluminosilicate based SCMs, mainly fly ash, slag, and calcined clay. In this review, the factors affecting limestone-SCM composites are summarised based on a detailed literature survey. The effects of SCM-limestone cement composites on hydration kinetics, reaction chemistry, the reactivity of SCMs, the stability of hydrated phases, and contribution to the physical structure development and macroscopic properties by evaluating hydration and mechanical properties are discussed. The importance of AFm (Al{sub 2}O{sub 3}–Fe{sub 2}O{sub 3}-mono) phases in various deterioration mechanisms in concrete and their influence on performance characteristics in different exposure environment is critically appraised.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Properties and reaction mechanism of phosphoric acid activated metakaolin geopolymer at varied curing temperatures

Reaction mechanism of phosphoric activated metakaolin is studied by techniques of calorimetry, ICP-OES, FTIR and NMR taking curing temperature and [H{sub 3}PO{sub 4}] as variables. A two-stage curing method including pre-curing at 40 °C for 24 h and second curing at 60/80 °C for another 24 h effectively mitigates thermal-cracking of the obtained silico-aluminate phosphate (SAP) samples, whose maximum compressive strength reaches 120 MPa. Dealumination of metakaolin in H{sub 3}PO{sub 4} solution produces low aluminate-containing silicate units and subsequently condensation of silicate tetrahedrons occurs. Higher temperature and H{sub 3}PO{sub 4} concentration accelerate the two processes. After complete reaction, A{sub VI} structure from metakaolin disappears and the dissolved Al preferably forms Al{sub VI}-O-P units. During reaction, metastable P-O-P intermediate appears in SAPs with higher P/Al ratio and finally transforms into Al-O-P structure upon PO{sub 4}{sup 3−} consumption. Phosphate units as P(OAl){sub x}(H{sub 2}O){sub 4-x} are connected with Si or Al structure units. Major structural units of the SAPs include Al-O-P, Si-O-P, Si-O-Si, and Si-O-Al.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strategies for control and mitigation of efflorescence in metakaolin-based geopolymers

Efflorescence can be harmful to material performance as a consequence of microstructural changes due to leaching and carbonation of alkalis. This article identifies mechanisms of efflorescence in metakaolin-based geopolymers, and approaches to reduce free/mobile alkali cations and pore network connectivity, and hence reduce efflorescence. Mechanical, mass transport and microstructural properties are assessed in metakaolin-based geopolymer cements produced using different alkali concentrations in the alkali activator and substitution/addition of blast furnace slag, silica fume, calcium aluminate cement, silicone oil and a dispersive admixture. The most effective strategy to reduce efflorescence results from increasing Si/Al in the geopolymer gel by addition of soluble silicate, silica fume or silicone oil. Addition of calcium aluminate cement or a dispersive admixture also reduce efflorescence, but are less effective. These results confirm that efflorescence may be reduced by controlling the amount of soluble silicates and reducing free alkali cations in geopolymers, providing enhanced performance and durability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength-promoting mechanism of alkanolamines on limestone-calcined clay cement and the role of sulfate

This paper reports the strength-promoting mechanism of alkanolamines on limestone-calcined clay cement (LC{sup 3}). The hydration kinetics, phase formation and microstructure of LC{sup 3} with triethanolamine (TEA) or triisopropanolamine (TIPA) were investigated. TEA enhanced the strength of LC{sup 3}, while TIPA was effective at 28 days, and a correct sulfate addition promoted their effects. Alkanolamines accelerated the aluminate reaction of LC{sup 3} during early hydration, increased sulfate slowed this reaction by producing more ettringite. TIPA favoured the hydration of ferrite in clinker, not only accelerated the silicate reaction of metakaolin, but also resulted in a rapid limestone reaction. Alkanolamines altered the morphology and chemical composition of the aluminate hydrates and C-A-S-H. Alkanolamines enabled the reduction of porosity of hardened pastes and the increased sulfate further refined them. It was the large pores being induced by TIPA at early ages that were considered to have an adverse impact on the early strength of LC{sup 3}.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nitrate and Nitrite Incompatibility with Hydroxide Ions in Concentrated NaOH Solutions: Implications for Hydroxide and Gibbsite Reactivity in Alkaline Nuclear Waste

Electrolyte solutions in alkaline nuclear waste contain aluminate, hydroxide, nitrate and nitrite with sodium as the predominant counterion. The salts of these ions are highly soluble, so the liquids are highly concentrated. This study found that there is a substantial incompatibility between the hydroxide and nitrate and/or nitrate ions. This was determined by the observations that adding just one molal of NaNO2 or NaNO3 to saturated NaOH solution precipitation of 12 moles of NaOH·H2O salt, whereas the common ion effect would have expected only about 1 mole to precipitate. Further analysis indicates that the presence of nitrate and nitrite drastically increases the reactivity of sodium hydroxide ions in solution, which likely influences the reactivity of other hydroxide-mediated reactions. This enhanced reactivity is likely because it disrupts large Na+-OH- ion networks because nitrate and nitrite do not fit in those ion networks similarly to how some ions cannot substitute into a foreign crystal lattice. In contrast, the aluminate ion did not have the same large incompatibility with hydroxide.

Nitrite, Nitrate, Aluminate, NaOH*H2O, Ion-aggrega↗
DOE OSTI2021

Development of CuFeMnAlO 4+δ oxygen carrier with high attrition resistance and 50-kWth methane/air chemical looping combustion tests

A Copper-Ferri-Manganese-Aluminate spinel (CuFeMnAlO 4+δ ) oxygen carrier, developed at the US Department of Energy’s (DOE) National Energy Technology Laboratory (NETL), shows promising results for chemical looping combustion with methane. Attrition resistance of the spinel oxygen carrier (160–600 µm) produced by a wet agglomeration method was significantly higher than that observed previously with a Copper-Ferri-Aluminate (CuFeAlO 4 ) oxygen carrier. Improved attrition resistance of the novel carrier can be attributed to minimal alumina phase segregation and minimal carbon formation. Heats of reaction measured by differential scanning calorimetry indicated exothermicity during reduction with methane. The total oxygen transfer capacity of the material was about 10.5 wt% at 850 °C. The attrition resistance and the oxygen transfer capacity of the carrier prepared at a commercial manufacturing facility (180 kg) were very similar to observed values during the development phase with the lab scale preparations. The material displays satisfactory methane conversion and significantly high particle durability during a 54 h test campaign conducted in NETL’s 50-kWth chemical looping dual fluid bed reactor unit at temperatures ranging from 700 to 900 °C. Low oxygen carrier make-up cost, due to the use of natural ore and pigment grade raw materials during synthesis and very low attrition rates, exceeded the performance goals determined by systems studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Condensation and growth of amorphous aluminosilicate nanoparticles via an aggregation process

The precipitation of zeolite nanoparticles involves the initial formation of metastable precursors, such as amorphous entities, that crystallize through non-classical pathways. Here, using reactive force field-based simulations, we reveal how aluminosilicate oligomers grow concomitantly to the decondensation of silicate entities during the initial step of the reaction. Aluminate clusters first form in the solution, thus violating the Loewenstein rule in the first instant of the reaction, which is then followed by their connection with silicate oligomers at the terminal silanol groups before reorganization to finally diffuse within the silicate oligomers to form stable amorphous aluminosilicate nanoparticles that do obey the Loewenstein rule. Our results clearly indicate that aluminate does not serve as the nucleation center for the growth of aluminosilicates in a nucleation-like process but rather proceeds via an aggregation process. Furthermore, the coexistence of aluminosilicate oligomers and small silicate entities induces a phase separation that promotes the precipitation of zeolites with aging.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effect of rare earth size on network structure and glass forming ability in binary aluminum garnets

Rare earth aluminate glasses are potentially useful for optical, luminescence, and laser applications. As reluctant glass formers, these materials exhibit unconventional atomic structures. To better understand how their structures correlate with glass formation, we investigate two rare earth aluminum garnet melts, La 3 Al 5 O 12 (LAG) and Yb 3 Al 5 O 12 (YbAG), which represent the relative extremes of good and poor glass forming ability in rare earth aluminates. Structural models have been refined to high-energy X-ray diffraction data over 1340–2740 K. Both melts contain mixtures of AlO 4 , AlO 5 , and AlO 6 polyhedra, with larger fractions of [5] Al and [6] Al in YbAG. Extrapolation of the Al–O coordination distributions to the glass transition match closely with 27 Al nuclear magnetic resonance measurements of (La 1−z Y z ) 3 Al 5 O 12 glasses, z = 0 to 1. During cooling, the mean coordination numbers increase for La–O in LAG from 6.45(8) to 6.98(8) and for Yb–O in YbAG from 6.02(8) to 6.21(8). Linkedness among Al–O polyhedra at ∼2450 K is mostly corner-sharing, with 9% edge-sharing in LAG and 19% in YbAG. Among [4] Al units, both melts have 6% edge-sharing that convert to all corner-sharing upon cooling. Network connectivity is compared using a newly defined metric, K n , that is similar to the Q n distribution but that accounts for the edge-sharing and triply bonded oxygen present in these melts. The lower glass forming ability in YbAG as compared to LAG correlates with more edge-sharing, associated with the larger fractions of [5] Al and [6] Al, and lower connectivity among [4] Al units.

Wilke, Stephen K. [Materials Development, Inc., Ar↗
DOE OSTI2020

Pascal conductance series in ballistic one-dimensional LaAlO 3 /SrTiO 3 channels

One-dimensional electronic systems can support exotic collective phases because of the enhanced role of electron correlations. We describe the experimental observation of a series of quantized conductance steps within strongly interacting electron waveguides formed at the lanthanum aluminate–strontium titanate (LaAlO 3 /SrTiO 3 ) interface. The waveguide conductance follows a characteristic sequence within Pascal’s triangle: (1, 3, 6, 10, 15, …) e 2 /h , where e is the electron charge and h is the Planck constant. This behavior is consistent with the existence of a family of degenerate quantum liquids formed from bound states of n = 2, 3, 4, … electrons. Our experimental setup could provide a setting for solid-state analogs of a wide range of composite fermionic phases.

Science & Technology - Other Topics↗
DOE OSTI2021

Updated Estimate of Tritium Permeation from TPBAR Disposal Containers in ILV (U)

A tritium source term analysis was performed for TPBAR disposal in the E-Area Intermediate Level Vaults for the E-Area Low-Level Waste Facility Performance Assessment (PA). This analysis is based on an earlier source term analysis which treated the bulk oft he tritium residual as tightly bound by the TPBAR getter material, with only a small fraction existing as tritiated moisture in the lithium aluminate ceramic pellets. Together with atmospheric moisture trapped in the free volume, the tritiated water vapor is assumed to corrode steel surfaces inside the disposal container, covering them with a magnetite film while generating hydrogen. The carbon steel walls of the disposal container are permeable to hydrogen, providing a path way for tritium to escape containment. The rate of hydrogen generation is assumed to be limited by the rate of corrosion, which is assumed to be governed by parabolic reaction kinetics obtained from the literature. This relies on the further assumption that the water vapor consumed by the corrosion reaction is continually replaced by moisture from the lithium aluminate pellets until all of that moisture is gone. In addition to tritium permeation, the analysis also includes a slow leak through the disposal container walls at the maximum allowable leak rate, 1 x 1CH standard cm3/s. Results were obtained for four different combinations of internal and container wall temperatures, established in an earlier thermal analysis that considered two different vault loadings and two different TPBAR activity levels. Instantaneous release rates for these four cases are plotted in Figure ES-1 below

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Development and Advanced Testing of DPC Cement Fillers

The fillers research and development (R&D) program, mostly experimental, is part of a broader R&D program that includes new process modeling and performance assessment of criticality effects and the overall importance of criticality to repository performance (consequence screening). A literature research and consultation effort with experts by Hardin and Brady (2018) identified several potentially effective and workable filler materials including cements (primarily phosphate based), moltenmetal alloys, and low-temperature glasses. Filler attributes were defined, and the preliminary lists were compared qualitatively. Further comparative analysis will be done (e.g., cost estimates) after experimental screening has narrowed the list of alternatives. The research presented here is focused Sandia’s efforts for the development of phosphate-based cement fillers. Molten metal filler research is an ongoing activity at Oak Ridge National Laboratories and is not discussed herein. After the completion of the FY20 research effort the following cement filler compositions were selected for further experimental development work and advanced testing in FY21: 1. Aluminum phosphate cements (APCs); more specifically aluminum oxide / aluminum phosphate (Al 2 O 3 / AlPO 4 ) cements in which Al 2 O 3 serves as the filler material bound by an AlPO 4 binder formed by the reaction of Al 2 O 3 with various phosphate sources; 2. Wollastonite phosphate cements (WPCs), specifically wollastonite and aluminum or calcium aluminum phosphates in which CaSiO 3 serves as the filler material bound by a calcium phosphate that serves as the binder; and 3. Calcium aluminate phosphate cements (CAPCs) specifically grossite (CaAl 4 O 7 ) and hibonite (CaAl 11 O 18 ) fillers bound by an aluminum phosphate that serves as the binder. This effort focused on the optimization and subsequent processing of these three cements to achieve dense and well-consolidated monolithic samples. Upon completion of the FY21 effort the aluminum phosphate cements (APCs) and the calcium aluminate phosphate cements (CAPCs) show the most promise for advanced testing and scale up. We will begin the work in FY22 focused on testing the performance of these two cements in small scale DPCs as well as advanced materials testing to evaluate cement performance under expected radiation doses and representative post-closure geochemical environments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Final Design for Thermal/Epithermal eXperiments (TEX) with Lithium Absorbers to Provide Validation Benchmarks for Y-12 Electrorefining Facility

One of the main goals of the Thermal/Epithermal eXperiments (TEX) project is to use existing Nuclear Criticality Safety Program (NCSP) assets to create critical experiment plutonium and uranium test beds for materials important to criticality safety that have insufficient benchmark evaluations. The plutonium test bed experiments were completed in 2018 and are published in the 2020 edition of the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The uranium test bed assemblies were completed in 2023 and accepted in the 2024 edition of the ICSBEP Handbook. The Nuclear Criticality Safety (NCS) group at Y-12 National Security Complex has identified programmatic need for validation cases for uranium electrorefining operations at Y-12. The electrorefining operation credits lithium enriched in 6 Li in addition to 35 Cl as absorbers in the design criticality safety evaluation for precluding criticality under upset conditions in the large and geometrically unfavorable electro-refiner. There is, however, inadequate experimental validation for the 6 Li absorbers. As an extension of the TEX uranium test bed, TEX-Cl critical experiments were performed with sodium chloride salt to address the 35 Cl thermal absorption as well as other validation needs at Los Alamos National Laboratory (LANL). These experiments were completed in 2024 and accepted into the 2025 ICSBEP Handbook. To continue the methodology used in TEX-Cl, TEX-Li aims to accomplish the same. The overall design of both experiments was to use commercially available, high purity, salts with polyethylene moderator and HEU plates to configure a critical assembly. Three experiments are planned for TEX-Li using encapsulated lithium carbonate (Li 2 CO 3 ), with natural 6 Li abundance. For all experiments, the highly enriched uranium (HEU) Jemima plates will be used as fissile material. Multiple layers will be stacked together with encapsulated Li 2 CO 3 alternated with polyethylene in standard configurations. Standard stacking was found to be optimal in matching the different sensitivity profiles provided by the Y-12 models. Three configurations are proposed with varying polyethylene moderation and a constant 1/4” absorber thickness. The first uses 11 layers of 5/4” polyethylene, the second uses 9 layers of 3/4” polyethylene, and the third uses 10 layers of 1/2” polyethylene. Calculations showed that some alternative forms of lithium-based materials provided slightly less-optimal sensitivity profiles when compared to lithium carbonate but come with other drawbacks. These alternatives included lithium aluminate (LiAlO 2 ), Aluminum-2050 alloy, Aluminum-8090, Aluminum-2095, lithium hydride (LiH), and lithium fluoride (LiF). Lithium aluminate and aluminum-2050 provided comparable sensitivity profiles when compared to lithium carbonate and can be used instead if lithium carbonate cannot be readily procured. After a broad material study, lithium carbonate outperformed any alternative material with a balance in affordability and workability. The assessment of experimental uncertainties of the non-absorber and absorber components was predicted to be 0.00089 and 0.00093 Δk eff , respectively. The largest uncertainties may be reduced with precision dimensional inspection of the components. Many of the parts and equipment for IER 575 have already been fabricated or procured for previous projects and therefore do not contribute significantly to the overall cost of this experiment. This includes the Jemima plates and Comet critical assembly machine, which are existing NCSP assets, as well as the aluminum platen and polyethylene reflector rings, which were fabricated and authorized for the TEX experiment involving HEU with polyethylene. Lithium carbonate containers will be procured by LANL and will be filled by LLNL. The total material costs for TEX-Li experiments are estimated to be on the order of $\$$47,400. Precision inspection, including dimensional, mass, density, and impurity, is recommended for all components for an estimated cost of $\$$12,000.

35Cl↗
NASA NTRS1972

Diffusion of chromium and aluminum in Ni-20Cr and TDNiCr /Ni-20Cr-2ThO2/.

Diffusion coefficients have been measured for Cr51 in fine- and coarse-grained TDNiCr (Ni-20Cr-2ThO2) and in fine-grained Ni-20Cr in the temperature range from 1038 to 1200 C. Selective diffusivities have also been determined for specimens of these alloys which were aluminized to give an initial surface concentration of 5.8 wt % Al. Finally, diffusion coefficients for interdiffusion of aluminum in TDNiCr and Ni-20Cr have been obtained from electron probe microanalysis of the aluminized specimens. For a given grain size and temperature there is no difference in diffusivities for chromium diffusion in TDNiCr or Ni-20Cr. Diffusion coefficients increase with decreasing grain size for both alloys. Comparison of aluminum diffusion data obtained from electron microprobe profiles with radiotracer chromium diffusivities suggests that aluminum diffuses approximately three times faster than chromium in TDNiCr and Ni-20Cr.

Seltzer, M. S.↗