Search NASA⌕ Search

SEARCH · Search NASA

Results for “AM Powder Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Lithium Ion Cathode Materials Prepared Using Glycerol as Solvent and Reactant

Two different types of cathode materials were prepared using glycerol as a solvent and reactant. The LiMn1/3Ni1/3Co1/3O2 layered oxide cathode material was successfully synthesized with a shorter time of heat treatment of 8hr at 900°C. An appreciated capacity retention of 83.7% after 100 cycles with an initial discharge capacity of 177.1 mAh/g at 0.1C (discharge rate) has been achieved. Another cathode material with the formula of Li1.2 Mn0.51Ni0.145+xCo0.145-xO2 (x=0 (LR2), 0.0725 (LR1)), as a Li-rich cathode material, has been also successfully synthesized using glycerol. It was shown that LR1 discharge capacity was increased from 185 to 213 mAh/g after 20 cycles and ended up with 194.9 mAh/g after 60 cycles at 0.1C (discharge rate). This material shows an exceptional discharge capacity retention, lower toxic cobalt component, and lower production cost comparing with other Li-rich cathode materials. Detailed results of powder material synthesis, characterization, and battery testing will be presented to demonstrate that glycerol as a green solvent in the synthesis of battery materials.

25 ENERGY STORAGE↗
NASA NTRS1989

Improved silicon carbide for advanced heat engines

The development of high strength, high reliability silicon carbide parts with complex shapes suitable for use in advanced heat engines is studied. Injection molding was the forming method selected for the program because it is capable of forming complex parts adaptable for mass production on an economically sound basis. The goals were to reach a Weibull characteristic strength of 550 MPa (80 ksi) and a Weibull modulus of 16 for bars tested in four-point loading. Statistically designed experiments were performed throughout the program and a fluid mixing process employing an attritor mixer was developed. Compositional improvements in the amounts and sources of boron and carbon used and a pressureless sintering cycle were developed which provided samples of about 99 percent of theoretical density. Strengths were found to improve significantly by annealing in air. Strengths in excess of 550 MPa (80 ksi) with Weibull modulus of about 9 were obtained. Further improvements in Weibull modulus to about 16 were realized by proof testing. This is an increase of 86 percent in strength and 100 percent in Weibull modulus over the baseline data generated at the beginning of the program. Molding yields were improved and flaw distributions were observed to follow a Poisson process. Magic angle spinning nuclear magnetic resonance spectra were found to be useful in characterizing the SiC powder and the sintered samples. Turbocharger rotors were molded and examined as an indication of the moldability of the mixes which were developed in this program.

Whalen, Thomas J.↗
NASA NTRS2003

Development of Ceramic Systems for High temperature Coatings

Professor Eslamloo-Grami will synthesize ceramic powders of various compositions based on pyrochlore, perovskite, and magnetoplumbite structures by doping with various oxides. Sol-gel and combustion synthesis routes will be used for powder syntheses. The powders will be characterized for particle size, surface area, microstructure, sintering etc. Thermal conductivity of the hot pressed specimens will also be measured at various temperatures. At the end, a project report will be prepared describing in details the experimental methods, results, discussion, and future research.

Eslamloo-Grami, Maryame↗
DOE OSTI2020

Grain size and structure distortion characterization of α-MgAgSb thermoelectric material by powder diffraction

Nanostructuring, structure distortion and/or disorder are the main manipulation techniques to reduce the lattice thermal conductivity and improve the figure of merit of thermoelectric materials. A single-phase α-MgAgSb sample, MgAg 0.97 Sb 0.99 , with high thermoelectric performance in near room temperature region was synthesized through a high-energy ball milling with a hot-pressing method. In this work, we report the average grain size of 24-28 nm and the accurate structure distortion, which are characterized by high-resolution neutron diffraction and synchrotron X-ray diffraction with Rietveld refinement data analysis. Both the small grain size and the structure distortion have a contribution to the low lattice thermal conductivity in MgAg 0.97 Sb 0.99 .

36 MATERIALS SCIENCE↗
DOE OSTI2024

Trends in electrocatalytic activity and stability of transition-metal nitrides

Transition metal nitrides (TMNs) are a class of electrocatalyst support materials similar to transition metal carbides (TMCs) with the advantage of avoiding the issues arising from graphitic carbon surface deposits during synthesis. Inspired by previous studies suggesting that TMCs could be used to reduce Pt loading for the hydrogen evolution reaction (HER), this work explored the feasibility of TMN-supported Pt and Au as HER electrocatalysts. Here this study established a volcano-like trend between electrochemical HER activity and hydrogen-binding energy (HBE) calculated from density functional theory. The Pt/TiN and Au/TiN materials were used to extend knowledge from well-characterized thin films to powder catalysts. In situ X-ray absorption spectroscopy (XAS) measurements provided additional characterization of the Pt/TiN and Au/TiN catalysts under HER conditions. Trends in the electrochemical stability of TMNs were also investigated over a wide range of potentials and pH values, which can be used to guide future studies for TMN-supported electrocatalysts.

58 GEOSCIENCES↗
DOE OSTI2024

Hypereutectic Al-Ce-X (X=Mn, Cr, V, Mo, W) alloys fabricated by laser powder-bed fusion

Here, we characterize the microstructures and high-temperature mechanical properties of Al-2Ce and ternary Al-2Ce-1X (at.%) alloys fabricated by laser powder-bed fusion (LPBF), where X = Mn, Cr, V, Mo, and W are slow-diffusing transition metals. All ternary alloys show a hypereutectic microstructure in the as-LPBF state, containing an interconnected network of eutectic Al 11 Ce 3 phases (~10 vol.%) and an additional population of submicron, equiaxed Al 20 CeX 2 primary precipitates (~10 vol.%) which are isomorphous among these five alloys. Similar microstructures are present in arc-melted rods and atomized powders but are coarser due to the slower cooling rates in these processes. The hardness of the as-LPBF ternary Al-Ce-X alloys (1300–1400 MPa) is higher than that of the binary Al-Ce alloy (~1100 MPa) due to the higher volume fraction of strengthening phases. Furthermore, during exposure at 400 °C for up to three months, greater hardness retention is achieved in the ternary Al-Ce-X alloys (65–75%) than in the binary Al-Ce alloy (~55%), which is attributed to the extreme coarsening resistance of the Al 20 CeX 2 precipitates imparted by the very slow-diffusing ternary solute. These coarsening-resistant Al 20 CeX 2 precipitates also substantially improve alloy creep resistance, increasing the threshold stress for dislocation creep at 300°C from ~32 MPa for the binary Al-Ce alloy to ~77–100 MPa for the ternary Al-Ce-X alloys, and at 400°C from <10 MPa for the binary Al-Ce alloy to >40 MPa for the ternary Al-Ce-V alloy.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Understanding the Feasibility of MAB Phase Structures for Lunar Applications

During the ten-week internship, my work focused on synthesis, characterization, and tailoring the flowability of the MAB phase powders for improving the surface finish and decreasing porosity of 3D-printed MAB phase structures. My mentor for the project was Dr. Samuel Hocker from NASA Langley and my faculty advisor was Dr. Surojit Gupta from the University of North Dakota. I also collaborated with Daniel Trieff from the University of North Dakota in developing characterization paradigm of 3D printed samples. The microencapsulation was performed via novel solvent casting-based microencapsulation process pioneered in UND, wherein a polymer (PLA, PHA) was dissolved into dichloromethane and precipitated onto the surface of the MoAlB particles. Two 100mL samples of microencapsulated powder was outsourced to Particle Technology Labs for flowability testing along with a 100mL control sample to determine if microencapsulation is a valid method for improving the flowability. The microencapsulated powders were characterized using SEM, Differential Scanning Calorimetry, and optical microscopy. The SEM images showed no change between the pure and microencapsulated powders. The optical microscopy analysis indicated a reduction in reflectivity for the PLA microencapsulated powders as well as hydrophobic properties. Both results suggest that microencapsulation was successful as PLA is a hydrophobic polymer and the change in reflectivity could be a result of the light being dispersed through the polymer coating. A reflectivity analysis will be done to bring more perspective to these observations. If powder flowability is improved, then the project will move forward with testing the printability of the microencapsulated powders and characterizing the structures using the designed characterization protocol. We are waiting for the DSC results. The characterization protocol for the 3D-printed MAB structures included a visual inspection of the plates to rule out any samples that had spalled or delaminated, optical microscopy to document surface features, porosity, and decomposition, and cleaning of the plates using an ultrasonic bath in preparation for SEM, EDS, and profilometry analyses.

MAB Phase↗
NASA NTRS1986

Colloidal characterization of ultrafine silicon carbide and silicon nitride powders

The effects of various powder treatment strategies on the colloid chemistry of aqueous dispersions of silicon carbide and silicon nitride are examined using a surface titration methodology. Pretreatments are used to differentiate between the true surface chemistry of the powders and artifacts resulting from exposure history. Silicon nitride powders require more extensive pretreatment to reveal consistent surface chemistry than do silicon carbide powders. As measured by titration, the degree of proton adsorption from the suspending fluid by pretreated silicon nitride and silicon carbide powders can both be made similar to that of silica.

Whitman, Pamela K.↗
DOE OSTI2024

Isotropic negative thermal expansion in ZrW 2 O 8 and HfW 2 O 8 from 1100 to 1275°C

Abstract ZrW 2 O 8 (ZrO 2 •2WO 3 ) and HfW 2 O 8 (HfO 2 •2WO 3 ) have been the focus of thermal expansion studies due to their isotropic negative thermal expansion (NTE) measured previously at temperatures below 775°C. This work presents measurements of these materials at their thermodynamically stable temperature ranges of 1105 and 1257°C for ZrW 2 O 8 and 1105–1276°C for HfW 2 O 8 , where they were characterized with in situ, powder X‐ray diffraction. The linear coefficients of thermal expansion were measured to be −5.52 × 10 −6 and −4.87 × 10 −6 °C −1 for ZrW 2 O 8 and HfW 2 O 8 , respectively. The mechanism leading to this NTE is discussed. Powder samples were synthesized by a solution‐based process called the organic–inorganic steric entrapment method. In situ characterization in air was carried out at the National Synchrotron Light Source II using a hexapole lamp, optical furnace and the Advanced Photon Source using a quadrupole lamp, optical furnace to achieve elevated temperatures.

Materials Science↗
DOE OSTI2019

Ball Milling Modified SAPO‐11 Based Catalysts for n ‐Decane Hydroisomerization

Abstract Bifunctional Pt/SAPO‐11 catalysts were prepared using as acid matrix the microporous silico‐aluminophosphate, SAPO‐11, synthesized under microwave radiation. After synthesis, the material was physically modified using a ball mill, changing the grinding time but keeping frequency constant. The metal function (0.5 wt.% Pt) was introduced through mechanical mixture with commercial Pt loaded alumina. The catalysts were characterized by several techniques: powder X‐Ray Diffraction, pyridine adsorption followed by infrared spectroscopy, low temperature N 2 adsorption, Hg intrusion porosimetry and electronic microscopy (SEM). The characterization data show modifications of structural and textural properties of the samples as the milling time increases. The catalytic behaviour of Pt/SAPO‐11 materials was studied for hydroisomerization of long chain n ‐alkanes, using n ‐decane as model molecule, aiming to increase the production of mono‐branched isomers. The catalytic results show that, under optimized milling conditions (60 min; 50 Hz) the selectivity into mono‐branched isomers increased when compared with parent catalyst.

Ferreira, Luisa↗
DOE OSTI2023

Rare Earth Nitrate Hybrid Double Perovskites [Me 4 N] 2 [MLn(NO 3 ) 6 ] (M = Na–Cs; Ln = La–Gd, ex. Pm)

An exploration of the synthetic and structural phase space of rare earth hybrid double perovskites A 2 B'BX 6 (A = organocation, B' = M + , B = M 3+ , X = molecular bridging anion) that include X = NO 3 – and B' = alkali metal is reported, complementing earlier studies of the [Me 4 N] 2 [KB(NO 3 ) 6 ] (B = Am, Cm, La–Nd, Sm–Lu, Y) (Me 4 N = (CH 3 ) 4 N + ) compounds. In the present efforts, the synthetic phase space of these systems is explored by varying the identity of the alkali metal ion at the B'-site. Herein, we report three new series of the form [Me 4 N] 2 [B'B(NO 3 ) 6 ] (B = La–Nd, Sm–Gd; B' = Na, Rb, Cs). The early members of the Na-series crystallize in the trigonal space group R3̅ from La to Nd where a phase transition occurs in the phase between 273 and 300 K, going from R3̅ to the high-symmetry, cubic space group Fm3̅m. The preceding trigonal members of the Na-series also undergo phase transitions to cubic symmetry at temperatures above 300 K, establishing a decreasing trend in the phase-transition temperature. The remainder of the Na-series, as well as the Rb- and Cs-series, all crystallize in Fm3̅m at 300 K. The temperature-dependent phase behavior of the synthesized phases is studied via variable-temperature spectroscopic methods and high-resolution powder X-ray diffractometry. All phases were characterized via single-crystal and powder X-ray diffraction and Fourier transform infrared (FT-IR) and Raman spectroscopic methods. These results demonstrate the versatility of the perovskite structure type to include rare earth ions, nitrate ions, and a suite of alkali metal ions and serve as a foundation for the design of functional rare earth hybrid double perovskite materials such as those possessing useful multiferroic, optical, and magnetic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

Characterization and development of materials for advanced textile composites

Work ongoing under the NASA Langley - Advanced Composite Technology (ACT) program is discussed. The primary emphasis of the work centers around the development and characterization of graphite fiber that has been impregnated with an epoxy powder. Four epoxies have been characterized in towpreg form as to their weaveability and braidability. Initial mechanical properties have been generated on each resin system. These include unidirectional as well as 8-harness satin cloth. Initial 2D and 3D weaving and braiding trials will be reported on as well as initial efforts to develop towpreg suitable for advanced tow placement.

Hartness, J. Timothy↗
DOE OSTI2026

The effect of varying powder feedstock chemistry and printing atmosphere on the microstructure of additively manufactured nickel-based ODS alloys: Role on stabilization of cellular structures vs. oxide dispersion formation

Nickel-based alloys have a wide variety of structural applications due to their high corrosion resistance and mechanical strength which depend on solid solution strengthening, or the formation of oxides and/or intermetallic precipitation for their properties. In this study, the microstructure of six Ni–Cr–Y–Ti–Al powder batches designed for the production of oxide dispersion strengthened nickel were compared. These batches varied in chemistry and atomization technique used which included Gas Atomization Reactive Synthesis (GARS). The batches of powder were then consolidated via Additive Manufacturing (AM) Powder Bed Fusion using Laser Beam (PBF-LB) and characterized via transmission electron microscopy to elucidate the influence of powder feedstock (i.e. synthesis methodology and chemistry) on the PBF-LB microstructure. The study investigates (i) how the amount of yttrium and titanium additions in the powder feedstock and the addition of oxygen during the processing (through GARS) affect the microstructure of the powder itself and the AM printed microstructure, and (ii) how the control of oxygen addition in the printing atmosphere during the PBF-LB printing process itself is another important parameter for achieving the formation of the wanted oxide dispersion versus the stabilization of the cellular structure (often observed in AM processed alloys). Microstructural characterization of both powder particles and additively manufactured nickel alloys in this study provide important insights into the movement of yttrium within the material upon solidification, particularly along cell boundaries, and how yttrium behaves depending on alloy chemistry. When a threshold of yttrium content is reached within the system, yttrium consistently reacts to form an intermetallic along cell boundaries instead of forming oxide nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of Magnesium Dopant on the Grain Boundary Stability of Nanocrystalline Aluminum Powders during Cryomilling

In this investigation, pure aluminum (Al) powders were cryomilled with and without magnesium dopants to study (a) the effect of cryomilling time on the crystallite size and (b) the effect of magnesium dopant on Al to achieve grain boundary stability. The cryomilling process was carried out using liquid nitrogen for different durations. The characterization of the cryomilled powders was carried out using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD) to understand the particle morphology, crystallite size, and elemental composition. The results demonstrated that the size of the crystallites in both Al and Mg-doped Al powders reduces as the cryomilling duration increases. The results also indicated that the preferential segregation of Mg dopant at the grain boundaries of Al provides stability to the cryomilled powders at elevated temperatures. This article discusses the mechanism for the changes in crystallite size and the effect of the Mg dopant on the grain boundary stability in Al powders.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-Situ Characterization of Pore Formation Dynamics in Pulsed Wave Laser Powder Bed Fusion

Laser powder bed fusion (LPBF) is an additive manufacturing technology with the capability of printing complex metal parts directly from digital models. Between two available emission modes employed in LPBF printing systems, pulsed wave (PW) emission provides more control over the heat input compared to continuous wave (CW) emission, which is highly beneficial for printing parts with intricate features. However, parts printed with pulsed wave LPBF (PW-LPBF) commonly contain pores, which degrade their mechanical properties. In this study, we reveal pore formation mechanisms during PW-LPBF in real time by using an in-situ high-speed synchrotron x-ray imaging technique. We found that vapor depression collapse proceeds when the laser irradiation stops within one pulse, resulting in occasional pore formation during PW-LPBF. We also revealed that the melt ejection and rapid melt pool solidification during pulsed-wave laser melting resulted in cavity formation and subsequent formation of a pore pattern in the melted track. The pore formation dynamics revealed here may provide guidance on developing pore elimination approaches.

36 MATERIALS SCIENCE↗