Search NASA⌕ Search

SEARCH · Search NASA

Results for “ASME Code Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Simulation of Internal Combustion Engines with High-Performance Computing Tools

Traditional Lagrangian spray modeling approaches for internal combustion engines are highly griddependent due to insufficient resolution in the near nozzle region. This is primarily because of inherent restrictions of volume fraction with the Lagrangian assumption together with high computational costs associated with small grid sizes. A state-of-the-art grid-convergent spray modeling approach was developed and implemented by Senecal et al. (ASME-ICEF2012-92043) in the CONVERGE software. The key features of the methodology include Adaptive Mesh Refinement (AMR), advanced liquid-gas momentum coupling, and improved distribution of the liquid phase, which enables use of cell sizes smaller than the nozzle diameter. This modeling approach was rigorously validated against nonevaporating, evaporating, and reacting data from the literature. The current numerical study focusses on further demonstration of the grid-convergent modeling approach for simulating a single-cylinder Cat® compression ignition engine. The simulated injector is characterized with a nominal nozzle exit diameter of 259 μm. Simulations using various minimum grid sizes (ranging from 125 μm to 1000 μm) are compared for engine performance and emissions parameters of interest such as pressure, heat release rate, ignition delay, NOx, HC, and soot emissions. The peak cell-count for the highest resolution simulation was on the order of 34 million. These computationally expensive simulations were facilitated at a high-performance computing facility at Argonne National Laboratory. METIS load-balancing algorithm was developed and implemented in Converge code for the simulations. Scaling studies were also performed. The validity of previously recommended grid settings (ASME-ICEF2012-92043) for accuracy/runtime trade-off is further assessed. Efficacy of a simplified combustion model is also compared against a detailed chemical kinetics based combustion model.

33 ADVANCED PROPULSION SYSTEMS↗

Design and Integrate Improved Systems for Nuclear Facility Ventilation and Exhaust Operations

Objective: The objective of this R&D project would complete the development of three new systems and integrate them into a single experimental effort. However, each of the three systems has stand-alone applicability across the DOE complex. At US DOE nuclear facilities, indoor air is filtered and ventilated for human occupancy, and exhaust air to the outdoor environment must be regulated and monitored. At least three technical standards address these functions, and the Los Alamos National Laboratory would complete an experimental facility to answer at least three questions: (1) Can the drag coefficient of a new Los Alamos air mixer be reduced for better operation in nuclear facility exhaust stacks? (2) Is it possible to verify the accuracy of a new dilution method for HEPA filter test facilities? (3) Is there a performance-based air flow metric (volumetric flow or mass flow) for operating HEPA filters? In summary, the three new systems are: a mixer, a diluter and a performance-based metric, respectively. The results of this project would be applicable to at least four technical standards: ANSI N13.1 Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stacks and Ducts of Nuclear Facilities; ASTM F1471 Standard Test Method for Air Cleaning Performance of a High-Efficiency Particulate Air Filter System, ASME N511: In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems, and ASME AG-1: Code On Nuclear Air And Gas Treatment. All of the three proposed new systems must be combined into a single experimental device (i.e. to develop a new function of the Los Alamos aerosol wind tunnel). Technical Approach: The Radiation Protection RP-SVS group at Los Alamos has an aerosol wind tunnel that was originally (2006) designed to evaluate small air samplers (cf. US EPA 40 CFR 53.42). In 2009, the tunnel was modified for exhaust stack verifications per the ANSI N13.1 standard. In 2010, modifications were started on the wind tunnel for testing HEPA filters (cf. ASTM F1471 and ASME N511). This project involves three systems that were developed for testing the 24*24*11 (inch) HEPA filters (i.e. the already mentioned mixer, diluter and metric). Prototypes of the mixer and the diluter have been built and individually tested on a preliminary basis. However, the third system (the HEPA metric method) has not been tested, since that requires complete operability of the aerosol wind tunnel device. (The experimental wind tunnel has test aerosol injection, control and measurement capabilities, and can be heated for temperature dependent measurements.) Benefits: US DOE facilities that use HEPA filters and/or require exhaust stacks from their nuclear facility buildings will benefit from access to the new hardware (mixer and diluter) and performance-based metric (for HEPA filter air flow).

61 RADIATION PROTECTION AND DOSIMETRY↗

EVALUATION OF ULTRASONIC PHASED-ARRAY FOR DETECTION OF PLANAR FLAWS IN HIGH-DENSITY POLYETHYLENE (HDPE) BUTT-FUSION JOINTS

The desire to use high-density polyethylene (HDPE) piping in buried Class 3 service and cooling water systems in nuclear power plants is primarily motivated by the material’s high resistance to corrosion relative to that of steel and metal alloys. The rules for construction of Class 3 HDPE pressure piping systems were originally published in Code Case N-755 and were recently incorporated into the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME BPVC) Section III as Mandatory Appendix XXVI (2015 Edition). The requirements for HDPE examination are guided by criteria developed for metal pipe and are based on industry-led HDPE research or conservative calculations.

HDPE↗

Structural Design and Modeling of MARVEL Primary Coolant System Using the ASME Section III, Division 5, Code

This paper presents the structural design and supporting analysis for the Microreactor Applications Research Validation and Evaluation (MARVEL) primary coolant system (PCS) using the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section III, Division 5, rules. MARVEL is a liquid metal–cooled microreactor intended to provide experimental capabilities for the rapid testing and development of microreactor technologies. The PCS utilizes high-temperature sodium-potassium liquid metal as the primary coolant and operates at a design temperature of 570°C, necessitating the consideration of creep-related failure mechanisms. The base metal for the PCS is 316H stainless steel, and the weldments are made with a 16-8-2 filler. The design approach incorporates the current base code rules along with ASME code cases N-924, N-861, and N-862 to address primary load, ratcheting, and creep-fatigue evaluations, respectively. The reactor’s operation involves complex thermal and mechanical interactions due to natural convective flow and differential thermal expansion between components. In conclusion, this paper discusses the structural engineering challenges encountered, such as managing thermal stresses in the distribution plenum and guard vessel, and outlines the strategies implemented to meet the code requirements, including design modifications and operational constraints.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

Implementation of algebraic stress models in a general 3-D Navier-Stokes method (PAB3D)

A three-dimensional multiblock Navier-Stokes code, PAB3D, which was developed for propulsion integration and general aerodynamic analysis, has been used extensively by NASA Langley and other organizations to perform both internal (exhaust) and external flow analysis of complex aircraft configurations. This code was designed to solve the simplified Reynolds Averaged Navier-Stokes equations. A two-equation k-epsilon turbulence model has been used with considerable success, especially for attached flows. Accurate predicting of transonic shock wave location and pressure recovery in separated flow regions has been more difficult. Two algebraic Reynolds stress models (ASM) have been recently implemented in the code that greatly improved the code's ability to predict these difficult flow conditions. Good agreement with Direct Numerical Simulation (DNS) for a subsonic flat plate was achieved with ASM's developed by Shih, Zhu, and Lumley and Gatski and Speziale. Good predictions were also achieved at subsonic and transonic Mach numbers for shock location and trailing edge boattail pressure recovery on a single-engine afterbody/nozzle model.

Abdol-Hamid, Khaled S.↗

Experimental Results on SS 304H and 2.25Cr-1Mo in Support of Developing Inelastic Constitutive Models

To address critical data gaps necessary for updating viscoplastic constitutive material models for Class A materials used in inelastic design analysis under the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors, Oak Ridge National Laboratory (ORNL) conducted experimental studies on stainless steel 304H (SS 304H) and 2¼Cr-1Mo steel (F22), to probe their temperature dependent deformation behaviors. These studies covered a range of temperatures up to the maximum limits specified in Division 5 and are intended to support the development of material models by collaborators at Argonne National Laboratory (ANL).

36 MATERIALS SCIENCE↗

Development of Grade 91 inelastic model for incorporation in ASME Division 5

This report describes a unified viscoplastic model for Grade 91 suitable for use with the Section III, Division 5 design by inelastic analysis procedures in the ASME Boiler and Pressure Vessel Code. The report identifies several key features a successful design inelastic model must capture along with critical aspects of the response of Grade 91 for elevated temperature loading conditions typical of expected reactor operating conditions. An inelastic model for Code design must capture the average response of a material including heat-to-heat and product form variations. This work develops a method for calibrating such a model to a large experimental database using genetic algorithm optimization. Finally, the report compares the final model to several specialized experimental tests to validate that it will be suitable for use in high temperature structural design. The techniques developed here can be applied to the remaining Section III, Division 5, Class A materials to develop a nonmandatory appendix to the Code describing inelastic material models suitable for use with the design by inelastic analysis procedures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

AGC-1 Pre-Irradiation Data Report Status

The Next Generation Nuclear Plant (NGNP) Graphite R&D program is currently measuring irradiated material property changes in several grades of nuclear graphite for predicting their behavior and operating performance within the core of new Very High Temperature Reactor (VHTR) designs. The Advanced Graphite Creep (AGC) experiment consisting of six irradiation capsules will generate this irradiated graphite performance data for NGNP reactor operating conditions. All samples in the experiment will be fully characterized before irradiation, irradiated in the Advanced Test Reactor (ATR), and then re-examined to determine the irradiation induced changes to key materials properties in the different graphite grades. The information generated during the AGC experiment will be utilized for NRC licensing of NGNP reactor designs, shared with international collaborators in the Generation IV Information Forum (GIF), and eventually utilized in ASME design code for graphite nuclear applications. This status report will describe the process the NGNP Graphite R&D program has developed to record the AGC1 pre-irradiation examination data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Stress concentration factors for circular, reinforced penetrations in pressurized cylindrical shells

The effect on stresses in a cylindrical shell with a circular penetration subject to internal pressure was investigated in thin, shallow linearly, elastic cylindrical shells. Results provide numerical predictions of peak stress concentration factors around nonreinforced and reinforced penetrations in pressurized cylindrical shells. Analytical results were correlated with published formulas, as well as theoretical and experimental results. An accuracy study was made of the finite element program for each of the configurations considered important in pressure vessel technology. A formula is developed to predict the peak stress concentration factor for analysis and/or design in conjunction with the ASME Boiler and Pressure Vessel Code.

Ramsey, J. W., Jr.↗

Application of the ASME Boiler and Pressure Vessel Code in the Design of SRF Cavities at Fermilab

Jacketed Superconducting Radio Frequency (SRF) cavities structurally comprise of an inner niobium vessel surrounded by a liquid helium containment vessels. The pressure of the helium bath and/or its volume might be such that a jacketed SRF cavity shall be considered a system of pressure vessels. Thus, methods described in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) should be used to analyze the structural soundness of jacketed SRF cavities. This paper will report the use of the set of rules developed at Fermilab for the design of SRF cavities, such as jacketed 1.3 GHz cavities for LCLS-II HE and jacketed Single Spoke Resonator type~2 (SSR2) for PIP-II, to ensure a similar level of safety as prescribed by the ASME BPVC.

43 PARTICLE ACCELERATORS↗

Optimization of Helium Vessel Design for ILC Cavities

The ILC (International Linear Collider) is a proposed new major particle accelerator. It consists of two 20 km long linear accelerators colliding electrons and positrons at an energy exceeding 500 GeV, Achieving this collision energy while keeping reasonable accelerator dimensions requires the use of high electric field superconducting cavities as the main acceleration element. These cavities are operated at l.3 GHz inside an appropriate container (He vessel) at temperatures as low as 1.4 K using superfluid Helium as the refrigerating medium. The purpose of this thesis, in the context of the ILC R&D activities currently in progress at Fermilab (Fermi National Accelerator Laboratory), is the mechanical study of an ILC superconducting cavity and Helium vessel prototype. The main goals of these studies are the determination of the limiting working conditions of the whole He vessel assembly, the simulation of the manufacturing process of the cavity end-caps and the assessment of the Helium vessel's efficiency. In addition this thesis studies the requirements to certify the compliance with the ASME Code of the whole cavity/vessel assembly. Several Finite Elements Analyses were performed by the candidate himself in order to perform the studies listed above and described in detail in Chapters 4 through 8. ln particular the candidate has developed an improved procedure to obtain more accurate results with lower computational times. These procedures will be accurately described in the following chapters. After an introduction that briefly describes the Fennilab and in particular the Technical Division (where all the activities concerning with this thesis were developed), the first part of this thesis (Chapters 2 and 3) explains some of the main aspects of modem particle accelerators. Moreover it describes the most important particle accelerators working at the moment and the basic features of the ILC project. Chapter 4 describes all the activities that were done to certify the compliance of the Helium vessel and the cavity to the ASME code standard. After briefly recalling to the main contents of the the ASME Code (Sections II and Vlll - Division ll), the procedure used for finding all relevant stresses and comparing the obtained results with the maximum values allowed are explained. This part also includes the buckling verification of the cavity. In Chapter 5 the manufacturing process of the cavity end-caps, whose function is to link the Helium vessel with the cavity, is studied. The present configuration of the dies is described and the manufacturing process is simulated in order to explain the origin of some defects fol.llld on real parts. Finally a new design of the dies is proposed and the resulting deformed piece is compared with the design requirements. Chapter 6 describes a finite elements analysis to assess the efficiency and the stiffness of the Helium vessel. Furthermore the results of the optimization of the Helium vessel (in order to increase the value of the efficiency) are reported. The same stiffness analysis is used in Chapter 7 for the Blade-Tuner study. After a description of this tuner and of its function, the preliminary analyses done to confirm the results provided by the vendor are described and then its limiting load conditions are found. Chapter 8 shows a study of the resistance of all the welds present in between the cavity and the end-cap and between the end-caps and the He vessel for a smaller superconducting cavity operating at 3.9 GHz. Finally Chapter 9 briefly describes some R&D activities in progress at INFN (Section of Pisa) and Fermilab that could produce significant cost reductions of the Helium vessel design. All the finite elements analyses contained and described in this thesis made possible the certification of the whole superconducting cavity-Helium vessel assembly at Fermilab. Furthermore they gave several useful indications to the Fermilab staff to improve the performance of the Helium vessel by modifying some design parameters or refining the manufacturing processes.

43 PARTICLE ACCELERATORS↗

Class B Materials Code Case

Class B Materials Code Case to include: FY25 - High temperature design methodology, overview of ASME Section III (Division 5), Design for elevated temperature service, Goal to address current gaps, evaluation of proposed rules, allowable stress development, Class A materials (existing ASME approach), variable confidence index, data extrapolation, bounding value for SEE, and next steps.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a mechanistic thermal aging model for Grade 91

This report provides a summary on understanding and predicting the effects of long-term thermal aging on microstructure and tensile properties of G91 to corroborate the ASME Code rules in strength reduction due to elevated temperature service. The research is to support the design and long-term operation of G91 structural components in sodium-cooled fast reactors (SFRs). The report is a Level 2 deliverable in FY18 (M2NT-18AN050502061), under the Work Package NT-18AN05050206, “G91 Code Extension Testing” performed by the Argonne National Laboratory (ANL), as part of the Advanced Materials Development Program for Fast Reactors. The thermal aging study of G91 involves three types of thermally-aged specimens: (1) specimens machined from two heats of G91, G91-H1 and H30176 that have been tested for the Advanced Materials Development Programs in the past years. These specimens were aged at 550, 600, and 650°C for times up to ~64,000 h; (2) specimens fabricated from the heads of the archived crept specimens (13 in total) of six heats of G91, H5349, H30394, H30383, H10148, H30176. These specimens were aged at 427 - 538°C and for times up to 132,647 h; (3) specimens made from a tube removed from the Kingston coal-fired power plant after exposure for 155,000 h at 550°C. These three sets of specimens provide a comprehensive data set for understanding and predicting the effect of long-term thermal aging on microstructure and tensile properties of G91. Microstructural analysis of the thermally-aged G91 revealed that thermal aging causes significant microstructural changes: (1) the tempered martensite formed during tempering is unstable, and suffers significant recovery during aging, manifested by an increase in subgrain width, a decrease in subgrain length, and a decrease in subgrain aspect ratio (i.e. subgrains become more equiaxed) as the aging temperature and time increase. The subgrain recovery is facilitated by the reduction of dislocation density within subgrains; (2) M23C6 carbides in the as-received G91 are distributed along grain and subgrain boundaries and play an important role as pinning obstacles against subgrain coarsening. M23C6 carbides coarsen during aging, and the coarsening of M23C6 carbides reduces the pinning force on the boundaries; (3) MX carbonitrides in the as-received G91 are distributed uniformly within subgrains, providing the precipitation hardening effect. They coarsen with increasing aging temperature and time, but the coarsening rate is low; (3) a new phase, the Laves phase intermetallic forms during aging. The formation of the Laves phase removes the Mo solutes from the matrix, reducing the solid solution strengthening effect. The Laves phase particles grow rapidly once they are nucleated, and they precipitate primarily along boundaries. They may have a pinning effect on boundaries, but should provide little to the alloy strength. The evolution of each microstructural constituent during thermal aging can be well described by individual microstructural models. The estimated activation energy for MX coarsening was 175 kJ/mol, equivalent to the activation energy for boundary and core diffusion in a-Fe, while the estimated activation energy for subgrain coarsening was significantly lower, ~96 kJ/mol. Thermal aging of G91 results in the reduction in the yield stress and the ultimate tensile strength but has an insignificant effect on the uniform and total elongations. The reduction in tensile strength is more pronounced as the aging temperature and time increases. The in situ tensile tests with high-energy X-rays revealed that sub-boundary strengthening plays a dominant role, and the strengthening role of M23C6 particles may be accounted for by subgrian boundary hardening, and three strengthening mechanisms can be superimposed to describe the tensile strength of G91: subgrain boundary hardening, MX precipitation hardening, and Mo solid solution strengthening. A microstructure – strength model was establ

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

APPLICATION OF THE FAVOR-OCI FRACTURE MECHANICS COMPUTER PROGRAM TO ASME CODE SECTION XI, IWB-3610 FLAW ACCEPTANCE CRITERIA EVALUATIONS

This paper presents an overview of added features in a new version of the FAVOR (Fracture Analysis of Vessels Oak Ridge) computer code called FAVOR-OCI. The original FAVOR code was developed at the US Department of Energy’s Oak Ridge National Laboratory (ORNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC). FAVOR is applied by US and international nuclear power industries to perform deterministic and probabilistic fracture mechanics analyses of commercial nuclear reactor pressure vessels (RPVs). Appli-cations of FAVOR are focused on insuring that the structural integrity of aging, and increasingly embrittled, RPVs is main-tained throughout their licensed service life. Based on the final ORNL release of FAVOR, v16.1, FAVOR-OCI extends existing deterministic features of FAVOR while preserving all prev-iously-existing probabilistic capabilities of FAVOR.The objective of this paper is to describe new deterministic features in FAVOR-OCI that can be applied to analytical evaluations of planar flaws. These evaluations are consistent with the acceptance criteria of ASME Code, Section XI, Article IWB-3610, including Subarticles IWB-3611 (acceptance based on flaw size) and IWB-3612 (acceptance based on applied stress intensity factor). The linear elastic fracture mechanics (LEFM) capabilities of FAVOR-OCI also incorporate the analytical procedures presented in the Nonmandatory Appendix A, Analysis of Flaws, Article A-3000, Method of KI Determination, for both surface and subsurface (embedded) flaws.The paper describes a computational methodology for determining critical values of fracture-related parameters that satisfy ASME Code Section XI acceptance criteria for flaws exposed to multiple thermal-hydraulic transients. These com-pute-intensive analyses can be carried out with a single execution of FAVOR-OCI. The new methodology determines critical values by solving for either the point of tangency or point of intersection between applied KI versus time histories and a user-selected fracture toughness material property (e.g., ASME KIc, FAVOR Weibull KIc, or Master Curve Weibull KJc) for surface or subsurface flaws. Situations where warm prestress conditions apply can also be addressed. The paper highlights a need for this new capability via applications to a recent independent review of safety cases for RPVs in two Belgian nuclear power plants (NPPs). That review required ASME Section XI assessments of several thousand embedded, quasi-laminar flaws in the wall of each RPV. Analysis results provided by the new capability contributed to the technical bases compiled from several sources by the Belgian nuclear regulatory agency (FANC) and eventually used by FANC to justify the restart of these NPPs.

Dickson, Terry L.↗

Simplified inelastic constitutive models for ASME Section III, Division 5 design by inelastic analysis

This report describes the development of simplified, universal constitutive model that captures the high temperature monotonic and cyclic behavior of a range of commonly-used high temperature materials. The goal of the work is to provide a simple, universal constitutive model to replace the current bespoke models for Grade 91, 316H, and Alloy 617 included in Nonmandatory Appendix HBB-Z of the ASME Boiler & Pressure Vessel Code, and to extend this model to cover Alloy 800H. We initiated this work in response to feedback from reactor vendors and other Code users requesting simplified models, compared to the current models, that are easier to implement and use in commercial finite element analysis software. This report describes the completion of this effort by developing a model to correct the defects in standard model forms presently used for high temperature material modeling, described in past work, developing and implementing new numerical methods to train this model against test data, and then actually training the model for the four materials. The report provides a complete mathematical description of the model along with the tabulated material coefficients for the four materials. The final step will be to formulate an ASME Code change to introduce the new models into the Code.

36 MATERIALS SCIENCE↗

Quarter 2 Research Performance Progress Report (RPPR) - DOE Solar Program

Creep-fatigue deformation is an important consideration for a thermal receiver of a gas phase (GP) Concentrating Solar Power (CSP) system due to the constant static stress or pressure, diurnal cycling, and elevated service temperatures required for efficient operation. An accurate description of the creep-fatigue behavior, not available for five of the six candidate materials, is important for assessment of preliminary designs. This project will provide a detailed analysis of the creep-fatigue behavior and damage accumulation of a candidate structural material for a CSP solar thermal receiver to address a critical knowledge barrier for receiver design in the GP pathway concept identified in the CSP Gen3 Demonstration Roadmap. This effort includes the development of rules for the design of solar receiver components against high temperature creep-fatigue and ratcheting failure modes. The ASME Code rules for high temperature nuclear components will form the basis of the method but adjustments will be made to reflect the generally shorter, diurnal operating cycles of thermal receivers and the relative consequences of failure, comparing nuclear to solar components. This is report covers the second quarter's work, which addressed outstanding questions on alloy selection for Quarter 1, and began laying the ground work for mechanical testing.

14 SOLAR ENERGY↗

Creep-Fatigue Behavior and Damage Accumulation of a Candidate Structural Material for Concentrating Solar Power Thermal Receiver Quarter 6 Report

Creep-fatigue deformation is an important consideration for a thermal receiver in Concentrating Solar Power (CSP) systems due to the constant static stress or pressure, diurnal cycling, and elevated service temperatures required for efficient operation. An accurate description of the creep-fatigue behavior, not available for five of the six candidate materials, is important for assessment of preliminary designs. This project will provide a detailed analysis of the creep-fatigue behavior and damage accumulation of a candidate structural material for a CSP solar thermal receiver to address a critical knowledge barrier for receiver designs identified in the CSP Gen3 Demonstration Roadmap. This effort includes the development of rules for the design of solar receiver components against high temperature creep-fatigue and ratcheting failure modes. The ASME Code rules for high temperature nuclear components will form the basis of the method but adjustments will be made to reflect the generally shorter, diurnal operating cycles of thermal receivers and the relative consequences of failure, comparing nuclear to solar components.

14 SOLAR ENERGY↗

Initial development of a high temperature life prediction method directly accounting for variability in material properties

This report presents the initial development of a life prediction method that accounts for the variability of the material properties in Grade 91 steel. We account for material variability by both fitting a variable 3-parameter Weibull distribution to the rupture data of the material and by quantifying the effect that the creep deformation properties have on stresses via a Monte Carlo approach. To ensure a reasonable time frame when applying Monte Carlo to the creep stress, we propose a methodology that models the material as an extremely viscous Stokes flow with a non-Newtonian viscosity, therefore solving the problem in a single step. We use the final probabilistic model for structural failure developed in this document to evaluate a Flat Head Vessel designed with the Section III, Division 5 ASME Boiler Pressure and Vessel Code rules with a 100,000h design life and assess its probability of premature failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗