Search NASA⌕ Search

SEARCH · Search NASA

Results for “ATF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

ATF-2 Sensitivity M&C 2023 (Slides)

Irradiation experiments in the Idaho National Laboratory's Advanced Test Reactor are typically assumed to have little effect on one another. This assumption does not hold true for certain experiments in close proximity. To evaluate the impacts on safety and programmatic parameters of experiments in the center flux trap, the contents of the adjacent H and inner-A positions are modeled with a range of possible irradiation targets. First, neutron flux maps with experiments in those positions are compared to those of a water-filled configuration. Then, several safety and programmatic parameters for a generic accident-tolerant fuel test train are calculated. It is shown that these parameters can exhibit considerable sensitivity to the contents of the H and A experiment positions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress on ATF development of SiC for LWR

Since 2011, Toshiba has been participating in a study whose objective is the commercial utilization of SiC instead of Zircaloy as LWR fuel material. During the period (Phase-1) from 2012 to 2015, feasibility studies on material design and fabrication were performed. This paper reports the principal results of a comprehensive feasibility study on SiC involving experiments and trial fabrication in terms of material properties, core and fuel design, and analytical simulation for safety analysis. The principal results are summarized as follows. First, the fabrication trials for the reduced scales of channel box and cladding have been successfully performed. Secondly, with regard to fuel rod performance analysis, hoop stress during normal operation may be a potential issue in fuel mechanical design as it is relatively high. Thirdly, with regard to safety analysis, the hydrogen generation of SiC fuel tends to decrease significantly compared with that of Zircaloy fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Accident Tolerant Fuels’ Neutronics Scoping Study (ATF-2Pert)

This summary discusses an ongoing scoping study to better understand the neutronic characteristics surrounding the center flux trap of the advanced test reactor. This summary details the need for the study, the means by which it was carried out, the study's results, and how the results benefit the accident tolerant fuels program.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Severe Accident Scoping Simulations of Accident Tolerant Fuel Concepts for BWRs

Accident-tolerant fuels (ATFs) are fuels and/or cladding that, in comparison with the standard uranium dioxide Zircaloy system, can tolerate loss of active cooling in the core for a considerably longer time period while maintaining or improving the fuel performance during normal operations. It is important to note that the currently used uranium dioxide Zircaloy fuel system tolerates design basis accidents (and anticipated operational occurrences and normal operation) as prescribed by the US Nuclear Regulatory Commission. Previously, preliminary simulations of the plant response have been performed under a range of accident scenarios using various ATF cladding concepts and fully ceramic microencapsulated fuel. Design basis loss of coolant accidents (LOCAs) and station blackout (SBO) severe accidents were analyzed at Oak Ridge National Laboratory (ORNL) for boiling water reactors (BWRs). Researchers have investigated the effects of thermal conductivity on design basis accidents, investigated silicon carbide (SiC) cladding, as well as the effects of ATF concepts on the late stage accident progression. These preliminary analyses were performed to provide initial insight into the possible improvements that ATF concepts could provide and to identify issues with respect to modeling ATF concepts. More recently, preliminary analyses for a range of ATF concepts have been evaluated internationally for LOCA and severe accident scenarios for the Chinese CPR1000 and the South Korean OPR-1000 pressurized water reactors (PWRs). In addition to these scoping studies, a common methodology and set of performance metrics were developed to compare and support prioritizing ATF concepts. A proposed ATF concept is based on iron-chromium-aluminum alloys (FeCrAl). With respect to enhancing accident tolerance, FeCrAl alloys have substantially slower oxidation kinetics compared to the zirconium alloys typically employed. During a severe accident, FeCrAl would tend to generate heat and hydrogen from oxidation at a slower rate compared to the zirconium-based alloys in use today. The previous study, [2], of the FeCrAl ATF concept during station blackout (SBO) severe accident scenarios in BWRs was based on simulating short term SBO (STSBO), long term SBO (LTSBO), and modified SBO scenarios occurring in a BWR-4 reactor with MARK-I containment. The analysis indicated that FeCrAl had the potential to delay the onset of fuel failure by a few hours depending on the scenario, and it could delay lower head failure by several hours. The analysis demonstrated reduced in-vessel hydrogen production. However, the work was preliminary and was based on limited knowledge of material properties for FeCrAl. Limitations of the MELCOR code were identified for direct use in modeling ATF concepts. This effort used an older version of MELCOR (1.8.5). Since these analyses, the BWR model has been updated for use in MELCOR 1.8.6, and more representative material properties for FeCrAl have been modeled. Sections 2 4 present updated analyses for the FeCrAl ATF concept response during severe accidents in a BWR. The purpose of the study is to estimate the potential gains afforded by the FeCrAl ATF concept during BWR SBO scenarios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Accident Tolerant Fuel Options For Near Term Applications

In this section, the basis for the proposal followed by description of the work scope and methodologies are discussed. Following the Fukushima disaster in 2011, US congress mandated the department of energy to start a R&D program on accident tolerant fuel (ATF) concepts for the existing light water reactor fleet. By 2015, the start date of this IRP, several ATF concepts were being pursued by various entities. In general, the ATF concepts were divided into two categories: near term and long term. The near term concepts included: Coated Zircaloy clad, fuels with additives and dopants and FeCrAl/steel based claddings. The long term concepts included: SiC composite cladding, high density fuels (U 3 Si 2 , UN) and TRISO type fuel forms (e.g. FCM). It is of particular importance for any DOE funded effort to give background information and original Funding Opportunity Announcement (FOA) goals in its final report to evaluate whether the FOA goals and the proposed work were actually addressed. The FOA for this IRP sought for modeling and simulation capability to predict various ATF performances during normal operation, design basis accident and severe accident conditions. Particularly, the FOA was concern with the state of the core performance during a severe accident. It was postulated that if an ATF retains its structural integrity, the performance of non-fuel structures in the core needs to be addressed. The IRP team focused the proposal on Pressurized Water Reactor (PWR) performance for near term ATF concepts: Coated cladding, Fuel with additives and dopants to accelerate adoption of such concepts and address the unanswered questions regarding their performance. The project also gave limited focus on another near term concept, FeCrAl cladding, by restricting its scope to time-to-failure prediction since substantial effort supported by other programs including ORNL ATF program, GEH ATF program and NEAMS High Impact Problem were already made or underway during the IRP tenure. Despite two previous IRPs funded in 2012 with focus on experimental study of metallic and ceramic Zircaloy coated claddings, this IRP still included a coating program. This was a testament to the project leadership’s belief that the coated clad concept will be the primarily initial pathway for near term industrialization of ATF technology due to presence of enrichment penalty and licensing hurdles of the alternative clad concepts. In doing so, the IRP was positioned to provide key findings on coated Zircaloy as a uniquely funded external program to DOE’s industrial ATF campaign. Currently, in 2019, the coated clad concept is being pursued by all three vendors for licensed application and Lead Test Rods and Lead Test Assemblies (LTRs/LTAs) have already been inserted or planned to be inserted in the existing fleet. At the start of the IRP project, based on the meeting with the projects technical and federal point of contacts, it was also agreed upon if the contractual obligations are met, then the scope of the simulation work will be extended to Boiling Water Reactors as included in Section 2.10.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Westinghouse Accident Tolerant Fuel Phase 2B with Higher Enriched and Higher Burnup Add-On Project Final Technical Report Deliverable Volume 1

The Westinghouse Electric Company LLC (Westinghouse) accident tolerant fuel (ATF) program funded by Westinghouse and the US Department of Energy (DOE) utilized chromium (Cr) coated zirconium alloy cladding with doped UO 2 (ADOPT(TM)) and uranium silicide (U 3 Si 2 ) high density/high thermal conductivity fuel for its lead test rod (LTR) program with irradiation beginning in 2019. ADOPT is a Cr 2 O 3 +Al 2 O 3 doped UO 2 pellet with increased oxidation resistance and density, and increased resistance to fission gas release. Due to the issues with U 3 Si 2 fuel reaction in pressurized water reactor (PWR) environments, uranium nitride (U 15 N) has been substituted for U 3 Si 2 as a long-term fuel option. Cr coated cladding with ADOPT fuel is the near-term Westinghouse EnCore fuel product. The long-term EnCore ® fuel product is SiGA ® SiC/SiC composite cladding with high density/high thermal conductivity UN fuel. In 2020, the higher burnup and higher enriched and (HBHE) program was integrated into the ATF program. The objective of this expanded program is to extend ATF burnups to at least 75 MWd/kgU to economically facilitate 24-month cycles in PWRs. The ATF program now includes ADOPT fuel with enrichments >5% 235 U. Over the past several years, Westinghouse has tested the Cr coated zirconium (Zr) and silicon carbide (SiC) claddings in Westinghouse Churchill autoclaves and the Massachusetts Institute of Technology (MIT) reactor. Additionally, the Cr coated cladding has been tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and in LTR programs at the Doel 4 and Bryon 2 commercial reactors. High temperature tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried out to determine the time and temperature limits for the Cr coated zirconium claddings. These tests indicate that Cr coated Zr cladding can take temperatures up to about 1500°C for short periods of time without becoming totally oxidized. The main issue is the formation of the Cr-Zr eutectic at 1333°C resulting in the migration of this eutectic inward with the formation of ZrCr 2 which rapidly oxidizes to ZrO 2 on the outside of the tube. The Cr coated Zr cladding also delays the bursting of the tube, reduces the burst area, and reduces hydriding and embrittlement of the Zr which is a major benefit for reducing fuel fragmentation, redistribution, and dispersal (FFRD), the major licensing issue faced by HBHE. The manufacturing parameters for the SiC have been found to have a significant effect on the corrosion rate of the SiC in light water reactor (LWR) conditions and significant improvements have been made in the yield, quality, and oxidation resistance of the SiC cladding by identifying and tightening manufacturing process parameters. Current autoclave results for SiC composite claddings indicate that a corrosion rate of fewer than 2 micrometers per year can be achieved which meets corrosion requirements under normal operating conditions. High temperature steam oxidation tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried and determined that SiC cladding can withstand temperatures up to about 1800°C to 1900°C before excessive corrosion reactions begin, and that the SiC will not balloon and burst. ADOPT fuel pellets were incorporated into the Westinghouse ATF program because of their increased density and oxidation resistance. A topical report supporting the use of ADOPT pellets has been submitted to the NRC and will be approved shortly. ADOPT pellets have been a product in Europe for over 15 years. The additives work to make larger grain sizes which appear to reduce fission gas release during transients as well as increase the density of the pellet. Fuel rod and assembly design in preparation for the lead test rod (LTR) and lead test assembly (LTA) programs is underway as well as licensing efforts with the Nuclear Regulatory Commission (NRC). Finally, accident analyses coupled with economic evaluations for both operating savings as well as fuel savings have been initiated. Modular Accident Analysis Program 5 (MAAP5) calculations indicate that both Cr coated cladding and SiC composite cladding can increase the time to fuel rod loss of geometry for up to two hours longer than current Zr based cladding in a station blackout scenario. This additional time is due to the much higher oxidation resistance of the SiC and Cr coated cladding. These two hours can be used to implement additional response options instituted through the Diverse and Flexible Mitigation Capability (FLEX) program by reactor operators. Both ATF cladding options also reduce hydrogen production which dramatically reduces primary system and containment pressure and the risk of fission product release beyond containment in the unlikely event of an accident. The lower pressure in the system allows more time to feed cooling water to the core, resulting in the avoidance of fuel melting. The coping time is extended indefinitely if the modest water flow provided by FLEX continues. Experimental work on methods to rapidly fabricate SiC composite structures with high density and reduce the fabrication price of SiC fibers while maintaining a high level of performance is needed. Methods for mitigating or stopping the Cr-Zr eutectic are also needed to further improve the oxidation resistance of Cr coated Zr. Minimal (<1%) swelling of U 3 Si 2 and subsequent fission gas release has been demonstrated up to 20 MWd/kgU. Irradiation experiments with U 3 Si 2 fuel in ATR to determine these properties at 40 MWd/kgU were completed but post irradiation examinations were not done since U 3 Si 2 has been replaced by UN. UN has three issues that are being addressed. The first is increasing the oxidation resistance so that there is not excessive reaction up to ~1500°C. While UN increases the pellet density and additives to the UN postponed the temperature at which rapid oxidation occurred by ~100°C to 200°C, this is not enough, and pellet coating options are now being pursued. The second is developing a method to manufacture that does not require the multi-step process of UF 6 to UO 2 to UC to UN. Efforts are underway looking at UF 6 to UN 2 to UN and UF 6 to UF 4 to UN 2 to UN reactions. Finally, an economically acceptable process for potentially enriching the 15 N content of the nitrogen used to make UN to >95% 15N was identified though not experimentally validated. In addition to the work supported by the DOE, research and testing activities are being carried on in a world-wide effort funded by many countries such as Sweden, United Kingdom, Belgium, Netherlands, Spain, Germany, Japan, and France. This work is being facilitated through the Westinghouse led Collaboration for Advanced Research on Accident Tolerant Fuel (CARAT) program. Annual meetings were organized in 2018 and 2019 by Westinghouse as a venue for presentation of this work and to provide for the cross-fertilization of ideas among the many outstanding researchers in the ATF area. No meetings were held in 2020 and 2021 due to the COVID-19 related restrictions on traveling and gatherings. Since SiC, coated cladding, and high-density fuel options are not currently used in the nuclear industry; support from the government and industry members is needed to further the significant effort of setting new standards. The same is true for the Nuclear Regulatory Commission (NRC) which must review and approve the commercial use of these new fuels since all current regulations are oriented toward Zr/UO 2 fuel. Several meetings have been held with the NRC to generate a fast-track approach to licensing ATF using a combination of atomic modeling, in-rod sensors, and in-reactor testing. This approach was memorialized in an “Accelerated Fuel Qualification White Paper” prepared by the Accelerated Fuel Qualification Working Group lead by General Atomics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Westinghouse Accident Tolerant Fuel Phase 2B with Higher Enriched and Higher Burnup Add-On Project Final Technical Report Deliverable Volume 2

The Westinghouse Electric Company LLC (Westinghouse) accident tolerant fuel (ATF) program funded by Westinghouse and the US Department of Energy (DOE) utilized chromium (Cr) coated zirconium alloy cladding with doped UO 2 (ADOPT(TM)) and uranium silicide (U 3 Si 2 ) high density/high thermal conductivity fuel for its lead test rod (LTR) program with irradiation beginning in 2019. ADOPT is a Cr 2 O 3 +Al 2 O 3 doped UO 2 pellet with increased oxidation resistance and density, and increased resistance to fission gas release. Due to the issues with U 3 Si 2 fuel reaction in pressurized water reactor (PWR) environments, uranium nitride (U 15 N) has been substituted for U 3 Si 2 as a long-term fuel option. Cr coated cladding with ADOPT fuel is the near-term Westinghouse EnCore ® fuel product. The long-term EnCore fuel product is SiGA ® SiC/SiC composite cladding with high density/high thermal conductivity UN fuel. In 2020, the higher burnup and higher enriched and (HBHE) program was integrated into the ATF program. The objective of this expanded program is to extend ATF burnups to at least 75 MWd/kgU to economically facilitate 24-month cycles in PWRs. The ATF program now includes ADOPT fuel with enrichments >5% 235 U. Over the past several years, Westinghouse has tested the Cr coated zirconium (Zr) and silicon carbide (SiC) claddings in Westinghouse Churchill autoclaves and the Massachusetts Institute of Technology (MIT) reactor. Additionally, the Cr coated cladding has been tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and in LTR programs at the Doel 4 and Bryon 2 commercial reactors. High temperature tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried out to determine the time and temperature limits for the Cr coated zirconium claddings. These tests indicate that Cr coated Zr cladding can take temperatures up to about 1500°C for short periods of time without becoming totally oxidized. The main issue is the formation of the Cr-Zr eutectic at 1333°C resulting in the migration of this eutectic inward with the formation of ZrCr 2 which rapidly oxidizes to ZrO 2 on the outside of the tube. The Cr coated Zr cladding also delays the bursting of the tube, reduces the burst area, and reduces hydriding and embrittlement of the Zr which is a major benefit for reducing fuel fragmentation, redistribution, and dispersal (FFRD), the major licensing issue faced by HBHE. The manufacturing parameters for the SiC have been found to have a significant effect on the corrosion rate of the SiC in light water reactor (LWR) conditions and significant improvements have been made in the yield, quality, and oxidation resistance of the SiC cladding by identifying and tightening manufacturing process parameters. Current autoclave results for SiC composite claddings indicate that a corrosion rate of fewer than 2 micrometers per year can be achieved which meets corrosion requirements under normal operating conditions. High temperature steam oxidation tests at the state-of-the-art Westinghouse facilities in Churchill, PA and at Karlsruhe Institute of Technology (KIT) have been carried and determined that SiC cladding can withstand temperatures up to about 1800°C to 1900°C before excessive corrosion reactions begin, and that the SiC will not balloon and burst. ADOPT fuel pellets were incorporated into the Westinghouse ATF program because of their increased density and oxidation resistance. A topical report supporting the use of ADOPT pellets has been submitted to the NRC and will be approved shortly. ADOPT pellets have been a product in Europe for over 15 years. The additives work to make larger grain sizes which appear to reduce fission gas release during transients as well as increase the density of the pellet. Fuel rod and assembly design in preparation for the lead test rod (LTR) and lead test assembly (LTA) programs is underway as well as licensing efforts with the Nuclear Regulatory Commission (NRC). Finally, accident analyses coupled with economic evaluations for both operating savings as well as fuel savings have been initiated. Modular Accident Analysis Program 5 (MAAP5) calculations indicate that both Cr coated cladding and SiC composite cladding can increase the time to fuel rod loss of geometry for up to two hours longer than current Zr based cladding in a station blackout scenario. This additional time is due to the much higher oxidation resistance of the SiC and Cr coated cladding. These two hours can be used to implement additional response options instituted through the Diverse and Flexible Mitigation Capability (FLEX) program by reactor operators. Both ATF cladding options also reduce hydrogen production which dramatically reduces primary system and containment pressure and the risk of fission product release beyond containment in the unlikely event of an accident. The lower pressure in the system allows more time to feed cooling water to the core, resulting in the avoidance of fuel melting. The coping time is extended indefinitely if the modest water flow provided by FLEX continues. Experimental work on methods to rapidly fabricate SiC composite structures with high density and reduce the fabrication price of SiC fibers while maintaining a high level of performance is needed. Methods for mitigating or stopping the Cr-Zr eutectic are also needed to further improve the oxidation resistance of Cr coated Zr. Minimal (<1%) swelling of U 3 Si 2 and subsequent fission gas release has been demonstrated up to 20 MWd/kgU. Irradiation experiments with U 3 Si 2 fuel in ATR to determine these properties at 40 MWd/kgU were completed but post irradiation examinations were not done since U 3 Si 2 has been replaced by UN. UN has three issues that are being addressed. The first is increasing the oxidation resistance so that there is not excessive reaction up to ~1500°C. While UN increases the pellet density and additives to the UN postponed the temperature at which rapid oxidation occurred by ~100°C to 200°C, this is not enough, and pellet coating options are now being pursued. The second is developing a method to manufacture that does not require the multi-step process of UF 6 to UO 2 to UC to UN. Efforts are underway looking at UF 6 to UN 2 to UN and UF 6 to UF 4 to UN 2 to UN reactions. Finally, an economically acceptable process for potentially enriching the 15 N content of the nitrogen used to make UN to >95% 15 N was identified though not experimentally validated. In addition to the work supported by the DOE, research and testing activities are being carried on in a world-wide effort funded by many countries such as Sweden, United Kingdom, Belgium, Netherlands, Spain, Germany, Japan, and France. This work is being facilitated through the Westinghouse led Collaboration for Advanced Research on Accident Tolerant Fuel (CARAT) program. Annual meetings were organized in 2018 and 2019 by Westinghouse as a venue for presentation of this work and to provide for the cross-fertilization of ideas among the many outstanding researchers in the ATF area. No meetings were held in 2020 and 2021 due to the COVID-19 related restrictions on traveling and gatherings. Since SiC, coated cladding, and high-density fuel options are not currently used in the nuclear industry; support from the government and industry members is needed to further the significant effort of setting new standards. The same is true for the Nuclear Regulatory Commission (NRC) which must review and approve the commercial use of these new fuels since all current regulations are oriented toward Zr/UO 2 fuel. Several meetings have been held with the NRC to generate a fast-track approach to licensing ATF using a combination of atomic modeling, in-rod sensors, and in-reactor testing. This approach was memorialized in an “Accelerated Fuel Qualification White Paper” prepared by the Accelerated Fuel Qualification Working Group lead by General Atomics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Source term analysis of FeCrAl accident tolerant fuel using MELCOR

It has been established that incremental improvements in beyond design basis accident performance can be achieved through accident tolerant fuel (ATF). However, they have the potential to recover margin with respect to conventional fuel and therefore enhance plant economics through uprate or cycle length increase. To realize this potential, it is necessary to quantify the reduction in source term due to use of ATF, and correspondingly how this is affected by increasing the cycle length and/or burnup. This requires development of a risk informed analysis methodology for ATF under high burnup conditions, which is being developed within LWRS. To this end, a MELCOR simulation of FeCrAl ATF in a recovered Large Break LOCA (LBLOCA) scenario has been developed, using a model based on the Zion Pressurized Water Reactor (PWR). The new user defined material capability, along with the inclusion of detailed neutronics- and depletion-derived parameters such as core power distribution, decay heat behavior, and fission product inventories, allows a more detailed simulation of FeCrAl clad material properties and behavior than has previously been possible using MELCOR. These detailed FeCrAl results were compared with a zircaloy clad model to investigate the differences between the two clad types and quantify the benefits of FeCrAl ATF with an 18-month cycle. Next, the fuel cycle with ATF was extended to 24 months, to determine whether any additional safety margin provided by FeCrAl ATF could be leveraged to implement high burnup FeCrAl-clad fuel while retaining the same operating and safety limits as current zircaloy-clad fuel. For the particular scenario analyzed, the delay to fuel failure from using ATF was of the same order as the LOCA recovery time, and hence significant in reducing fission product release, with the 24-month FeCrAl core performing better than the 18-month zircaloy core. It is noted that for other transients, the reduction in release due to using FeCrAl may be less significant. Furthermore, the material model developed here can be used in such further studies in support of determining the overall source term.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A magnetic isolation and pointing system for the astrometric telescope facility

The astrometric telescope facility (ATF), a 20-meter telescope designed for long-term detection and observation of planetary systems outside of the solar system, is scheduled to be a major user of the Space Station's payload pointing system (PPS) capabilities. However, because the ATF has such a stringent pointing stability specification (as low as 0.01 arcsec error over the frequency range from 5 to 200 hertz) and requires +/- 180-degree roll rotation around the telescope's line of sight, the ATF's utilization of the PPS requires the addition of a mechanism or mechanisms to enhance the basic PPS capabilities. The results of a study conducted to investigate the ATF pointing performance achievable by the addition of a magnetic isolation and pointing (MIPS) system between the PPS upper gimbal and the ATF, and separately, by the addition of a passive isolation system between the Space Station and the PPS base are presented. In addition, the study produced requirements on magnetic force and gap motion as a function of the level of Space Station disturbance. These results were used to support the definition of a candidate MIPS. Pointing performance results from the study indicate that a MIPS can meet the ATF pointing requirements in the presence of a PPS base transitional acceleration of up to 0.018g, with reasonable restrictions placed on the isolation and pointing bandwidths. By contrast, the passive base isolator system must have an unrealistically low isolation bandwidth on all axes (less than 0.1 hertz) to meet ATF pointing requirements. The candidate MIPS is based on an assumed base translational disturbance of 0.01g. The system fits within the available annular region between the PPS and ATF while meeting power and weight limitations and providing the required payload roll motion. Payload data and power services are provided by noncontacting transfer devices.

Smith, Marcie↗

Investigations on the Thermal-hydraulic Behavior of Accident Tolerant Fuel Cladding Materials

Since the 2011 Fukushima accident, significant research has been devoted to developing accident-tolerant fuel (ATF) cladding materials. These investigations have mostly focused on the ability to resist runaway steam oxidation and retain mechanical strength and structural integrity under thermal shocks. However, much remains unknown about the materials’ thermal-hydraulic behavior, particularly under light-water reactor (LWR) operating conditions. Two phenomena that determine safety margins in both normal and off-normal operating conditions - i.e., the critical heat flux (CHF) and Leidenfrost point (LFP) temperature - have not been investigated thoroughly for ATF materials. Surface properties, such as wettability and roughness, are known to influence pool and flow boiling CHF, as well as the LFP temperature. However, little is known about the surface wettability of ATF materials, particularly at LWR pressure and temperature. Little has been done on flow-boiling CHF and quenching heat transfer, especially for droplet quenching. Nonetheless, it is known that CHF in transient conditions, e.g., an exponentially escalating power transient, can be significantly different from that expected in steady-state operation. Very few studies have investigated transient CHF, either on ATF materials or under LWR pressure and temperature. The thorough understanding of transient CHF under prototypical reactor conditions will benefit not only the deployment of ATF but also the upcoming national efforts to study transient ATF behavior in the Transient Reactor Test Facility (TREAT) at Idaho National Laboratory. In summary, as a part of ATF development efforts, there is an urgent need to understand how and how much these materials may affect two-phase heat transfer phenomena in nuclear reactor conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Dynamic Probabilistic Risk Assessment Based Response Surface Approach for FLEX and Accident Tolerant Fuels for Medium Break LOCA Spectrum

After the Fukushima Daiichi Accident, the safety features such as accident tolerant fuel (ATF) and diverse and flexible coping strategies (FLEX) for existing nuclear fleets are being investigated by the US Department of Energy under the Light Water Reactor Sustainability Program. This research is being conducted to quantify the risk-benefit of these safety features. Dynamic probabilistic risk assessment (DPRA)-based response-surface approach has been presented to quantify the FLEX and ATF benefits by estimating the risk associated with each option. ATFs with multilayered silicon carbide (SiC), iron-chromium-aluminum, and chromium-coated zirconium cladding were considered in this study. While these ATF candidates perform better than the current zirconium cladding (Zr), they may introduce additional failure modes in some operating conditions. The fuel failure analysis modules (FAMs) were developed to investigate ATF performance. The dynamic risk assessments were performed using RAVEN, a DPRA tool, coupled with RELAP5 and FAMs. A cumulative distribution function-based index provided a mean of comparing the benefits of safety enhancements. For medium break loss of coolant accidents, FLEX operational timing window for each fuel type was estimated. Among these ATF candidates, SiC-type ATF was the most beneficial candidate for an increased safety margin than Zr-based fuel and was found to complement FLEX strategies in terms of risk and coping time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

R&D Roadmap for Enhanced Resilient Plant Systems, Metrics, Scenarios, Risk Analysis, and Modeling and Simulation

The nuclear industry and the U.S. Department of Energy are jointly developing accident tolerant fuel (ATF) which has the potential to greatly improve the safety and economic performance of the current fleet of NPPs. The combination of ATF with the optimal use of FLEX equipment (deployed as an industry response to the Fukushima Daiichi Nuclear Power Plant (NPP) accident in 2012), enhancements on plant components and systems, incorporation of augmented cooling systems or new passive cooling systems, and improvements in fuel cycle efficiency, have the potential to render the NPPs more efficient and resilient to events (both internally and externally initiated) that have the potential to challenge the integrity of the fuel or plant containment. In this report, combinations of these plant improvements are called Enhanced Resilient Plant Systems. In order to accelerate the development and deployment of the components that comprise Enhanced Resilient Plant Systems, a well-integrated toolkit that is fuel/clad-, fuel cycle-, systems-, and scenario-centric is required to provide a ready platform for the analysis of the advanced ATF fuel and cladding materials that are being developed, as well as plant systems modifications to achieve enhanced resiliency. Since the deployment of these enhancements will comprise a risk/benefit tradeoff of their impacts on plant safety and economics, the envisioned toolkit will need to be capable to characterizing the multidimensional aspects associated with these evaluations and provide decision-makers with information that can optimize the technological, economic, and safety benefits that are to be obtained. The Risk-Informed Systems Analysis (RISA) Pathway of the DOE Light Water Reactor Sustainability (LWRS) Program initiated several research tasks to develop analytical capabilities to support the industry in the transition to the ATF and Enhanced Resilient Plant Systems. The general idea behind the initiative is the development of an integrated evaluation approach which combines the plant probabilistic risk assessment (PRA) models with Multi-Physics Best Estimate Plus Uncertainty (MP-BEPU) analyses in a seamless fashion. The integrated evaluation framework aims at enabling plant system configuration variations to be studied with speed and precision, including detailed risk and benefit assessments of introducing ATF and Enhanced Resilient Plant Systems into current LWR plants to achieve both safety and operational performance enhancements. The focus of this report is to present an integrated research and development (R&D) roadmap to identify and perform high value evaluations of proposed ATF and Enhanced Resilient Plant Systems concepts to identify both the technical (e.g. benefits to risk, safety, and operational margins) and the economic (i.e. business and cost) elements associated with industry adoption of the technology. The integrated evaluation approach will be developed to support the development, testing, qualification, licensing, and deployment of ATF and Enhanced Resilient Plant Systems technology that is capable of achieving substantial safety and economic improvements as well as timely widespread adoption by the US nuclear industry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Enhanced Accident-Tolerant Fuel Performance and Reliability for Aggressive iPWR/SMR Operation

This project will develop a process that evaluates the whole-core operational and safety performance of a reactor-and-fuel combination by integrating core-wide three-dimensional neutronics with Moose/Bison and Peregrine multi-physics fuel performance assessments using explicit time and space dependent fuel rod operational power histories generated in the whole-core analysis. Demonstration of the process will target large contemporary PWRs with traditional UO2 fuel and Zircaloy cladding to establish a baseline analysis, while the innovative application of this project will extend the developed process to evaluate operational and safety performance, via reactor physics and fuel performance analyses, of key emerging/leading concepts of enhanced Accident Tolerant Fuels (ATFs) within increasingly aggressive operational scenarios such as loadfollow maneuvers in PWRs and long-cycle rodded and unborated operation in small modular reactors (SMRs). The ATFs to be considered include standard UO2 fuel pellets cladded with advanced iron-based alloys (FeCrAl) as well as particle-based Fully Ceramic Microencapsulated (FCM) fuels with FeCrAl or Zircaloy cladding, but the process being developed and demonstrated could ultimately be applied to any candidate ATF concept in a light water reactor. In fact, given that ATF R&D priorities are in a dynamic state, the scope related to ATFs will be targeted for the second half of this three-year project so to provide some opportunity to strengthen the programmatic alignment of this project with the DOE Fuels Campaign, by identifying the most promising and relevant ATFs at that time for further evaluation, while the early part of the project will focus upon fine-tuning the process herein developed and upon generating the baseline analyses against which a larger scope of ATF concepts can be compared.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SCALE Lattice Physics Code Assessments of Accident Tolerant Fuel

This report highlights accident-tolerant fuel (ATF) code assessment activities performed under Project NRCHQ- 60-17-T-0017, Lattice Physics Enhancements and Assessment. ATF covers a broad range of advanced fuel and clad designs for light water reactors (LWRs) to enhance performance under several accident conditions. Several ATF concepts are anticipated to be deployed as lead test rods (LTRs) or lead test assemblies (LTAs) within the next five years. The purpose of this work is to assess the predictive capabilities of NRC neutronics codes that underpin various licensing calculations. ATF designs use different fuel and clad materials compared to standard UO 2 fuel and zirconium-alloy claddings (hereafter UO 2 -Zry). These new materials and geometrical designs need to be assessed to quantify the impact of nuclear data uncertainties on quantities of interest (QOIs) in licensing calculations and the impact of modeling approximations which may be valid for UO 2 -Zry but not for ATF. This report outlines a systematic approach for ATF neutronics code assessment which includes sensitivity and uncertainty (S/U) analysis of nuclear data, identification of experimental benchmark and gaps for code validation, investigation of modeling approximations, and code-to-code comparisons of calculated QOIs against high-fidelity reference continuous energy (CE) Monte Carlo (MC) calculations. This report focuses on the assessment of the SCALE/Polaris lattice physics code for reactor safety analysis. Polaris lattice physics calculations generate few group (FG) cross sections for PARCS full-core calculations. (Full-core analysis, spent fuel analysis, and severe accident analysis will be performed in future work.) The selected ATF concepts for this report include Cr 2 O 3 and Al 2 O 3 -Cr 2 O 3 -doped UO 2 fuel, U 3 Si 2 fuel, FeCrAl cladding, SiC cladding, and Cr-coated cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Laser Wakefield Acceleration Driven by a CO2 Laser (STELLA-LW) - Final Report

The original goals of the Staged Electron Laser Acceleration – Laser Wakefield (STELLA-LW) program were to investigate two new methods for laser wakefield acceleration (LWFA). In pseudo-resonant LWFA (PR-LWFA), a laser pulse experiences nonlinear pulse steepening while traveling through the plasma. This steepening allows the laser pulse to generate wakefields even though the laser pulse length is too long for resonant LWFA to occur. For the conditions of this program, PR-LWFA requires a minimum laser peak power of 3 TW and a low plasma density (10^16 cm^-3). Seeded self-modulated LWFA (seeded SM-LWFA) combines LWFA with plasma wakefield acceleration (PWFA). An ultrashort (~100 fs) electron beam bunch acts as a seed in a plasma to form a wakefield via PWFA. This wakefield is subsequently amplified by the laser pulse through a self-modulated LWFA process. At least 1 TW laser power and, for a ~100-fs bunch, a plasma density ~10^17 cm^-3 are required. STELLA-LW was located on Beamline #1 at the Brookhaven National Laboratory (BNL) Accelerator Test Facility (ATF). The ATF TW CO2 laser served as the driving laser beam for both methods. For PR-LWFA, a single bunch was to probe the wakefield produced by the laser beam. For seeded SM-LWFA, the ATF linac would produce two bunches, where the first would be the seed and the second would be the witness. A chicane would compress the first bunch to enable it to generate wakefields via PWFA. The plasma source was a short-length, gas-filled capillary discharge with the laser beam tightly focused in the center of the capillary, i.e., no laser guiding was used, in order to obtain the needed laser intensity. During the course of the program, several major changes had to be made. First, the ATF could not complete the upgrade of the CO2 laser to the 3 TW peak power needed for the PR-LWFA experiment. Therefore, the PR-LWFA experiment had to be abandoned leaving only the seeded SM-LWFA experiment. Second, the ATF discovered that the chicane bifurcated the incoming bunch into two compressed bunches separated in time and energy. With the available equipment it was not possible to stop the bifurcation. In an attempt to still deliver a single compressed bunch to the experiment, a slit was used to block one of the bunches, but this also blocked any witness bunch. Third, the loss of the witness bunch meant a different method for detecting the effect of the laser beam on the wakefield had to be implemented. Hence, a coherent Thomson scattering (CTS) diagnostic was designed and assembled. Unfortunately, further tests with blocking one of the double-bunches showed that wakefield generation was too unstable and difficult to control for the seeded SM-LWFA experiment. Luckily, it was found that a fast-rising (~50 fs) bunch could be created along Beamline #2 that was capable of generating wakefields, did not use the chicane, and was more stable. Thus, as the fourth major change, the entire STELLA-LW apparatus, including the CTS diagnostic, was moved from Beamline #1 to Beamline #2. Because this move occurred near the end of the program, only a single 2-week run could be performed. During the run it was found the laser beam transmission through the capillary discharge was severely degraded when the plasma was on. This loss of transmission appeared to be due to defocusing of the laser beam probably caused by laser-induced ionization creating a lens effect inside the capillary. Defocusing could also cause laser light to strike the capillary wall, thereby producing ablation and localized changes in the plasma density. Any changes in the plasma density would disrupt the plasma resonance condition for the wakefield. It was also discovered after the run that the ATF laser was producing multiple output pulses. The leading pulse could have caused ionization that interfered with transmission of the following pulses. Worse yet, the peak power in each of the pulses was several times smaller than if all the pulse energy was in a single pulse. This meant each pulse had less than 1 TW power. Wakefield formation with no laser beam present was confirmed by observing energy loss of the fast-raising seed bunch passing through the capillary discharge. When the laser beam was sent into the plasma, no CTS signal was detected, probably due to defocusing of the laser light, changes in the plasma density due to laser-induced ionization, and insufficient peak power in the individual pulses. It is for these reasons we were not able to validate the seeded SM-LWFA predictions. In summary, the STELLA-LW experiment was not able to demonstrate seeded SM-LWFA or PR-LWFA primarily because of limitations of the ATF CO2 laser, both in its deliverable peak power and its ability to provide a single laser pulse.

43 PARTICLE ACCELERATORS↗