Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced Combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Emissions from premixed charge compression ignition (PCCI) combustion and affect on emission control devices

A light-duty diesel engine has been operated in advanced combustion modes known generally as premixed charge compression ignition (PCCI). The emissions have been characterized for several load and speed combinations. Fewer NO{sub x} and particulate matter (PM) emissions are produced by PCCI, but higher CO and hydrocarbon (HC) emissions result. In addition, the nature of the PM differs from conventional combustion; the PM is smaller and has a much higher soluble organic fraction (SOF) content (68% vs. 30% for conventional combustion). Three catalyst technologies were studied to determine the affects of HECC on catalyst performance; the technologies were a lean NO{sub x} trap (LNT), diesel oxidation catalyst (DOC), and diesel particulate filter (DPF). The LNT benefited greatly from the reduced NO{sub x} emissions associated with PCCI. NO{sub x} capacity requirements are reduced as well as overall tailpipe NO{sub x} levels particularly at low load and temperature conditions where regeneration of the LNT is difficult. The DOC performance requirements for PCCI are more stringent due to the higher CO and HC emissions; however, the DOC was effective at controlling the higher CO and HC emissions at conditions above the light-off temperature. Below light-off, CO and HC emissions are problematic. The study of DPF technology focused on the fuel penalties associated with DPF regeneration or 'desoot' due to the different PM loading rates from PCCI vs. conventional combustion. Less frequent desoot events were required from the lower PM from PCCI and, when used in conjunction with an LNT, the lower PM from less frequent LNT regeneration. The lower desoot frequency leads a {approx}3% fuel penalty for a mixture of PCCI and conventional loads vs. {approx}4% for conventional only combustion.

33 ADVANCED PROPULSION SYSTEMS↗

Current and Future Technologies for Power Generation with Post-Combustion Carbon Capture

The objective of this study is to support DOE’s Carbon Capture and Advanced Combustion R&D Programs by completing an 'R&D Pathway” study for PC power plants that employ post-combustion carbon capture. The pathway begins with representation of today's technology and extends to include emerging carbon capture, advanced steam conditions, and advanced CO 2 compression with corresponding performance/cost estimates to illustrate routes to achieving the DOE goal of = 35% increase in cost of electricity relative to a PC plant without CO 2 capture.

20 FOSSIL-FUELED POWER PLANTS↗

Comparing the greenhouse gas emissions from three alternative waste combustion concepts

Highlights: Black-Right-Pointing-Pointer Significant GHG reductions are possible by efficient WtE technologies. Black-Right-Pointing-Pointer CHP and high power-to-heat ratio provide significant GHG savings. Black-Right-Pointing-Pointer N{sub 2}O and coal mine type are important in LCA GHG emissions of FBC co-combustion. Black-Right-Pointing-Pointer Substituting coal and fuel oil by waste is beneficial in electricity and heat production. Black-Right-Pointing-Pointer Substituting natural gas by waste may not be reasonable in CHP generation. - Abstract: Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO{sub 2}-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Powertrain Controls Optimization for HD Hybrid Line Haul Trucks - FY2014 Annual Report

This is a vehicle system level project, encompassing analytical modeling and supervisory controls development as well as experimental verification/validation testing at the component, powertrain, and full vehicle system level. This project supports the goal of petroleum consumption reduction for medium and heavy trucks through the development of advanced hybrid technologies and control systems. VSST has invested previously in R&D to support hybrid energy storage systems (Li-ion plus ultra-caps) for light duty, passenger car applications. This research will be extended to the MD and HD sector where current battery technology is not mature enough to handle the substantial regenerative braking power levels these trucks are capable of producing. With this hybrid energy storage system, substantial gains in overall vehicle efficiency are possible. In addition, advanced combustion technologies, such as RCCI, will be implemented into an advanced hybrid powertrain for a Class 8 line haul application. This powertrain, leveraged from other VSST work (Meritor, a current ORNL/VSST partner), is ideal for taking advantage of the benefits of RCCI operation due to its series hybrid mode of operation. Emissions control is also a focus of this project, especially due to the fact that RCCI creates a low temperature exhaust stream that must addressed.

33 ADVANCED PROPULSION SYSTEMS↗

Knock Mitigation Effectiveness of EGR across the Pressure-Temperature Domain

Exhaust gas recirculation (EGR) has been shown to enable efficiency improvements in SI engines through multiple different mechanisms, including decreasing the knock propensity at high load, which allows higher compression ratio. While many of the benefits of EGR are applicable to both low and high power density engines, including reductions in pumping work and improved specific heat ratio, the knock benefits and corresponding compression ratio increases have been limited to low power density naturally aspirated engines primarily intended for hybrid vehicle architectures. An earlier study [1] indicated that there may be a kinetic limitation for the ability of EGR to mitigate knock under these conditions, but that study only considered a small number of conditions. In this investigation, we expand on that study while also providing data for model validation for the new light-duty combustion consortium from the U.S. Department of Energy: Partnership for Advancing Combustion Engines (PACE). In this investigation, the effectiveness of EGR to mitigate knock is studied with regards to the effect of engine speed (1,500 and 3,000 rpm), changing trajectory in the pressure-temperature domain by varying the intake manifold temperature (35, 60, and 90 deg C), and by considering the effect of minor species by studying the effect of untreated EGR vs. EGR that has been treated by an automotive three-way catalyst. Additionally, to increase the relevance of these data for future modeling studies, the performance of the full boiling range gasoline was compared relative to a surrogate formulation. The study found that the fuel surrogate performs well, confirmed the kinetic limitations of EGR to mitigate knock under boost, and showed improvements in EGR performance with catalyzed EGR.

42 ENGINEERING↗

Fuels research: Combustion effects overview

The effects of broadened property fuels on gas turbine combustors were assessed. Those physical and chemical properties of fuels that affect aviation gas turbine combustion were isolated and identified. Combustion sensitivity to variations in particular fuel properties were determined. Advanced combustion concepts and subcomponents that could lessen the effect of using broadened property fuels were also identified.

Haggard, J. B., Jr.↗

Reactivity-controlled compression ignition drive cycle emissions and fuel economy estimations using vehicle system simulations

In-cylinder blending of gasoline and diesel to achieve reactivity-controlled compression ignition has been shown to reduce NO X and soot emissions while maintaining or improving brake thermal efficiency as compared with conventional diesel combustion. The reactivity-controlled compression ignition concept has an advantage over many advanced combustion strategies in that the fuel reactivity can be tailored to the engine speed and load, allowing stable low-temperature combustion to be extended over more of the light-duty drive cycle load range. In this paper, a multi-mode reactivity-controlled compression ignition strategy is employed where the engine switches from reactivity-controlled compression ignition to conventional diesel combustion when speed and load demand are outside of the experimentally determined reactivity-controlled compression ignition range. The potential for reactivity-controlled compression ignition to reduce drive cycle fuel economy and emissions is not clearly understood and is explored here by simulating the fuel economy and emissions for a multi-mode reactivity-controlled compression ignition–enabled vehicle operating over a variety of US drive cycles using experimental engine maps for multi-mode reactivity-controlled compression ignition, conventional diesel combustion, and a 2009 port-fuel injected gasoline engine. Drive cycle simulations are completed assuming a conventional mid-size passenger vehicle with an automatic transmission. Multi-mode reactivity-controlled compression ignition fuel economy simulation results are compared with the same vehicle powered by a representative 2009 port-fuel injected gasoline engine over multiple drive cycles. Finally, engine-out drive cycle emissions are compared with conventional diesel combustion, and observations regarding relative gasoline and diesel tank sizes needed for the various drive cycles are also summarized.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Hydrogen shift isomerizations in the kinetics of the second oxidation mechanism of alkane combustion. Reactions of the hydroperoxypentylperoxy OOQOOH radical

Hydroperoxyalkylperoxy species are important intermediates that are generated during the autoignition of transport fuels. In combustion, the fate of hydroperoxyalkylperoxy is important for the performance of advanced combustion engines, especially for autoignition. A key fate of the hydroperoxyalkylperoxy is a 1,5 H-shift, for which kinetics data are experimentally unavailable. In the present work, we study 1-hydroperoxypentan-3-yl)dioxidanyl (CH 3 CH 2 CH(OO)CH 2 CH 2 OOH) as a model compound to clarify the kinetics of 1,5 H-shift of hydroperoxyalkylperoxy species, in particular α-H isomerization and alternative competitive pathways. With a combination of electronic structure calculations, we determine previously missing thermochemical data, and with multipath variational transition state theory (MP-VTST), a multidimensional tunneling (MT) approximation, multiple-structure anharmonicity, and torsional potential anharmonicity, we obtained much more accurate rate constants than the ones that can computed by conventional single-structure harmonic transition state theory (TST) and than the empirically estimated rate constants that are currently used in combustion modeling. The roles of various factors in determining the rates are elucidated. The pressure-dependent rate constants for these competitive reactions are computed using system-specific quantum RRK theory. The calculated temperature range is 298–1500 K, and the pressure range is 0.01–100 atm. The accurate thermodynamic and kinetics data determined in this work are indispensable in the detailed understanding and prediction of ignition properties of hydrocarbons and alternative fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combustion Synthesis of Advanced Porous Materials in Microgravity Environment

Combustion synthesis, otherwise known as self-propagating high temperature synthesis (SHS), can be used to produce engineered advanced porous material implants which offer the possibility for bone ingrowth as well as a permanent structure framework for the long-term replacement of bone defects. The primary advantage of SHS is based on its rapid kinetics and favorable energetics. The structure and properties of materials produced by SHS are strongly dependent on the combustion reaction conditions. Combustion reaction conditions such as reaction stoichiometry, particle size, green density, the presence and use of diluents or inert reactants, and pre-heating of the reactants, will affect the exothermicity of the reaction. A number of conditions must be satisfied in order to obtain high porosity materials: an optimal amount of liquid, gas and solid phases must be present in the combustion front. Therefore, a balance among these phases at the combustion front must be created by the SHS reaction to successfully engineer a bone replacement material system. Microgravity testing has extended the ability to form porous products. The convective heat transfer mechanisms which operate in normal gravity, 1 g, constrain the combustion synthesis reactions. Gravity also acts to limit the porosity which may be formed as the force of gravity serves to restrict the gas expansion and the liquid movement during reaction. Infiltration of the porous product with other phases can modify both the extent of porosity and the mechanical properties.

Zhang, X.↗

Oxy-Combustion System Process Optimization

The overall objective of this work is to develop a new chemical absorbent-based, high pressure, CO 2 purification system to remove the residual oxygen that currently contaminates the recovered CO 2 , and to optimize the Pressurized Oxy-Combustion (POxC) process to minimize the Cost of Electricity (COE) generated in this advanced combustion process. TDA developed and validated the performance of the oxygen removal system for CO 2 purification. In collaboration with the Advanced Power & Energy Program (APEP) of University of California, Irvine (UCI), we optimized the POxC process, including thermal management, heat integration, and power cycle optimization using process design and modeling supported with Aspen Plus® process simulations. The techno-economic analysis results indicate that the pressurized oxycombustion coal power plant with Ion-transport membrane (ITM) air separation unit (ASU) (Case 2 – 30.55%) does not show an advantage over a cryogenic ASU (Case 1 – 31.24%) while TDA’s sorption-based ASU (Case 4 - 32.61%) shows a significant advantage over the cryogenic ASU (Case 1 – 331.24%). The specific plant costs show a wide range with a low of $2544/kW for Case 11C (TDA ASU, co-sequestering the SO x , and ultra-supercritical steam cycle) to a high of $2975/kW for Case 12A (cryogenic ASU and sCO 2 cycle). In general, the ITM ASU based cases have lower specific plant costs than the corresponding cryogenic ASU based cases while the TDA ASU based cases show the lowest specific plant costs. The main reason for lowering these costs is the higher overall plant thermal efficiency which decreases the plant cost on a $ per kW basis. Next comparing the cases with different power cycle working fluid conditions in terms of temperature and pressure while all utilizing steam, similar trends as the plant costs may be observed. However, with the supercritical CO 2 (sCO 2 ) cycle, the increase in thermal efficiency of the sCO 2 cycle was not able to offset its increase in plant cost making the plant costs higher than those of the corresponding steam cycle cases. The Cost of Electricity (COE) again shows similar trends as the specific plant costs. The COE for Case 11C at $110.1/MWh is also the lowest, but among all cases that do not co-sequester the SO x , Case 12C (TDA ASU and sCO 2 cycle) has the lowest COE at $\$$117.5/MWh while the highest is for Case 8A (cryogenic ASU and supercritical steam cycle) at $130.4/MWh.

20 FOSSIL-FUELED POWER PLANTS↗

Low-Temperature Combustion of High Octane Fuels in a Gasoline Compression Ignition Engine

Gasoline Compression Ignition (GCI) has been shown as one of the advanced combustion concepts that could potentially provide a pathway to achieve cleaner and more efficient combustion engines. Fuel and air in GCI are not fully premixed as compared to homogeneous charge compression ignition (HCCI) which is a completely kinetic-controlled combustion system. Therefore, the combustion phasing can be controlled by the time of injection, usually post injection in a multiple-injection scheme, to mitigate combustion noise. Gasoline fuels ignite more difficult than Diesel. The autoignition quality of gasoline can be indicated by research octane number (RON). Fuels with high octane tend to have more resistance to auto-ignition, hence more time for fuel-air mixing. In this study, three fuels, namely, Aromatic, Alkylate, and E30, with similar RON value of 98 but different hydrocarbon compositions were tested in a multi-cylinder engine under GCI combustion mode. Considerations of EGR, start of injection (SOI), and boost were investigated to study the sensitivity of dilution, local stratification, and reactivity of the charge, respectively, for each fuel. Combustion phasing was kept constant during the experiments to the changes in ignition and combustion process before and after 50% of the fuel mass is burned. Emission characteristics at different levels of EGR and lambda were revealed for all fuels with E30 having the lowest filter smoke number (FSN) and was also most sensitive to the change in dilution. Reasonably low combustion noise (< 90 dB) and stable combustion (COVIMEP < 3%) were maintained during the experiments. The second part of this paper contains visualization of the combustion process obtained from endoscope imaging for each fuel at selected conditions. Soot radiation signal from GCI combustion were strong during late injection, and also more intense at low EGR conditions. Furthermore, soot/temperature profiles indicated only the high-temperature combustion period, while cylinder pressure-based heat release rate (HRR) showed a two-stage combustion phenomenon.

33 ADVANCED PROPULSION SYSTEMS↗

Negative Valve Overlap Reforming Chemistry in Low-Oxygen Environments

Fuel injection into the negative valve overlap (NVO) period is a common method for controlling combustion phasing in homogeneous charge compression ignition (HCCI) and other forms of advanced combustion. When fuel is injected into O2-deficient NVO conditions, a portion of the fuel can be converted to products containing significant levels of H2 and CO. Additionally, other short chain hydrocarbons are produced by means of thermal cracking, water-gas shift, and partial oxidation reactions. The present study experimentally investigates the fuel reforming chemistry that occurs during NVO. To this end, two very different experimental facilities are utilized and their results are compared. One facility is located at Oak Ridge National Laboratory, which uses a custom research engine cycle developed to isolate the NVO event from main combustion, allowing a steady stream of NVO reformate to be exhausted from the engine and chemically analyzed. The other experimental facility, located at Sandia National Laboratories, uses a dump valve to capture the exhaust from a single NVO event for analysis. Results from the two experiments are in excellent trend-wise agreement and indicate that the reforming process under low-O2 conditions produces substantial concentrations of H2, CO, methane, and other short-chain hydrocarbon species. The concentration of these species is found to be strongly dependent on fuel injection timing and injected fuel type, with weaker dependencies on NVO duration and initial temperature, indicating that NVO reforming is kinetically slow. Further, NVO reforming does not require a large energy input from the engine, meaning that it is not thermodynamically expensive. The implications of these results on HCCI and other forms of combustion are discussed in detail.

HCCI↗

Investigation of Bio-Diesel Fueled Engines under Low-Temperature Combustion Strategies

In accordance with meeting DOE technical targets this research was aimed at developing and optimizing new fuel injection technologies and strategies for the combustion of clean burning renewable fuels in diesel engines. In addition a simultaneous minimum 20% improvement in fuel economy was targeted with the aid of this novel advanced combustion system. Biodiesel and other renewable fuels have unique properties that can be leveraged to reduce emissions and increase engine efficiency. This research is an investigation into the combustion characteristics of biodiesel and its impacts on the performance of a Low Temperature Combustion (LTC) engine, which is a novel engine configuration that incorporates technologies and strategies for simultaneously reducing NOx and particulate emissions while increasing engine efficiency. Generating fundamental knowledge about the properties of biodiesel and blends with petroleum-derived diesel and their impact on in-cylinder fuel atomization and combustion processes was an important initial step to being able to optimize fuel injection strategies as well as introduce new technologies. With the benefit of this knowledge experiments were performed on both optical and metal LTC engines in which combustion and emissions could be observed and measured under realistic conditions. With the aid these experiments and detailed combustion models strategies were identified and applied in order to improve fuel economy and simultaneously reduce emissions.

33 ADVANCED PROPULSION SYSTEMS↗

An experimental investigation of low octane gasoline in diesel engines.

Conventional combustion techniques struggle to meet the current emissions norms. In particular, oxides of nitrogen (NO{sub x}) and particulate matter (PM) emissions have limited the utilization of diesel fuel in compression ignition engines. Advance combustion concepts have proved the potential to combine fuel efficiency and improved emission performance. Low-temperature combustion (LTC) offers reduced NO{sub x} and PM emissions with comparable modern diesel engine efficiencies. The ability of premixed, low-temperature compression ignition to deliver low PM and NO{sub x} emissions is dependent on achieving optimal combustion phasing. Diesel operated LTC is limited by early knocking combustion, whereas conventional gasoline operated LTC is limited by misfiring. So the concept of using an unconventional fuel with the properties in between those two boundary fuels has been experimented in this paper. Low-octane (84 RON) gasoline has shown comparable diesel efficiencies with the lowest NO{sub x} emissions at reasonable high power densities (NO{sub x} emission was 1 g/kW h at 12 bar BMEP and 2750 rpm).

02 PETROLEUM↗

A predictive 0-D HCCI combustion model for ethanol, natural gas, gasoline, and primary reference fuel blends

Homogeneous Charge Compression Ignition (HCCI) is a promising advanced combustion concept with high thermal efficiency and low exhaust emissions. This work purposes a computationally-efficient, zero-dimensional (0-D) HCCI combustion model that does not need to solve any differential equations. To develop the burn rate correlations, experimental HCCI data of ethanol, natural gas, E10-gasoline, and Primary Reference Fuel (PRF) blends was collected on a CFR engine. The burn rate model is built based on the individual cycle mass fraction burned (MFB) curves calculated from the experimental data. CA0 can be predicted from an ignition delay correlation. Once CA0 is known, CA50 and CA90 can be predicted based on CA0 and the charge-mass equivalence ratio Φ'. Then, with CA0, 50 and 90 known, a Wiebe function can be constructed to represent the MFB curve and burn rate. For PRF blends, low-temperature and high-temperature heat releases (LTHR and HTHR) are modeled by two Wiebe functions with Φ' and PRF number dependence. The fitted model has high accuracy compared to the experimental data with R 2 values generally greater than 0.97. Finally, various ignition delay correlations from the literature are also tested against the experimentally collected data and some modifications to the correlations are suggested.

42 ENGINEERING↗

In-Cylinder Reaction Chemistry and Kinetics During Negative Valve Overlap Fuel Injection Under Low-Oxygen Conditions

Fuel injection into the negative valve overlap (NVO) period is a common method for controlling combustion phasing in homogeneous charge compression ignition (HCCI) as well as other forms of advanced combustion. During this event, at least a portion of the fuel hydrocarbons can be converted to products containing significant levels of H2 and CO, as well as other short chain hydrocarbons by means of thermal cracking, water-gas shift, and partial oxidation reactions, depending on the availability of oxygen and the time-temperature-pressure history. The resulting products alter the autoignition properties of the combined fuel mixture for HCCI. Fuel-rich chemistry in a partial oxidation environment is also relevant to other high efficiency engine concepts (e.g., the dedicated EGR (D-EGR) concept from SWRI). In this study, we used a unique 6-stroke engine cycle to experimentally investigate the chemistry of a range of fuels injected during NVO under low oxygen conditions. Fuels investigated included iso-octane, iso-butanol, ethanol, and methanol. Products from NVO chemistry were highly dependent on fuel type and injection timing, with iso-octane producing less than 1.5% hydrogen and methanol producing more than 8%. We compare the experimental trends with CHEMKIN (single zone, 0-D model) predictions using multiple kinetic mechanisms available in the current literature. Our primary conclusion is that the kinetic mechanisms investigated are unable to accurately predict the magnitude and trends of major species we observed.

6-stroke cycle↗

Limitations of cetane number to predict transient combustion phenomena in high-pressure fuel sprays

Fundamental understanding of in-cylinder processes in diesel engines is important to screen emerging biofuels and advanced combustion modes that can reduce greenhouse gas emissions and regulated pollutants including soot. In this study, the role of fuel properties on spray development and combustion is investigated by systematically isolating chemical and thermophysical effects. Three different fuels are considered, two with similar chemical properties and two with similar thermophysical properties with one fuel common to both groups. Experiments are performed in a constant-pressure flow chamber de-signed to provide stable test conditions and facilitate acquisition of at least 150 injections in quick succession for each fuel under reacting conditions at high-pressure, high-temperature ambient conditions using a modified conventional diesel engine injector. Further, high speed optical diagnostics including rainbow schlieren deflectometry, OH* chemiluminescence, and a two-color pyrometry system are employed to simultaneously image the transient spray and reacting jets. Image analysis is performed to determine liquid length, vapor penetration length, timing and location of first stage and main ignition events, lift-off location, total soot mass, and more. Results show that fuels with similar chemical properties or cetane number (CN) exhibit similar delay times for first stage and main ignition events as may be expected, but very different liquid length, first stage and main ignition locations, lift-off length, apparent turbulent flame speed, and soot formation. As such, the ability to characterize candidate biofuels with CN or other parameters derived from simple flame configurations is called into question. In this study, thermo-physical properties controlling the liquid length are identified as the main contributing factor for the observed differences.

33 ADVANCED PROPULSION SYSTEMS↗

Rotating Detonation Combustion for Gas Turbines – Modeling and System Synthesis to Exceed 65% Efficiency Goal

Program description to date for the program. Objective: To advance combustion turbine technologies for combined cycle applications ... by integrating a Rotating Detonation Engine (RDE), pressure gain combustion system with an air-breathing power-generating turbine system to achieve a combined cycle efficiency equal to or greater than 65%.

rotating detonation, pressure gain combustion, rot↗