Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

A Report from the Thermal Science Research Center (TSRC)

A vertical flow loop was designed and assembled to determine the local (circumferential and axial) and mean wall temperature distributions for single-phase and two-phase (subcooled and saturated) downward flow in both uniformly-heated and single-side heated vertical channels. Freon-11 was used as the working fluid in order to directly relate and compare the results with a previous experimental campaign which employed this same working fluid. For a given steady-state experiment, the following parameters were held constant: (1) exit pressure, (2) inlet temperature, and (3) mass velocity. For a given configuration of the 2.2 m long cylindrical channel test section, which had a 1.2 m long heated section, the applied heat rate was varied from zero through successive quasi-steady states to a level which corresponded to localized film boiling in the test section. The measurements showed that the boiling curve changes significantly at higher mass velocities with respect to both the circumferential and axial directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential direction. The measurements point to the existence of a dry-out phenomenon occurring at multiple levels of the applied heat for the single-side heated channel. In comparing the heat transfer for horizontal channel flow with a vertically downward flow, the results show that significantly lower heat transfer occurs in the horizontal flow. However, this trend reverses as both the Reynolds number and the applied heat rate increase. Both the Liu-Winterton and Shah correlations were compared with the experimental data. The Shah correlation predicted the uniformly heated tube data better. When a thermal hydraulic diameter approach was used for the single-side heated case, the data at upstream locations for Z/L less than 0.5 was bounded above by the Liu-Winterton correlation and below by the Shah correlation. At Z/L = 0.5, the Shah correlation bounded the data; and for Z/L greater than 0.5, both correlations overpredicted the data with the Shah correlation being closest to the data. The present results indicate that additional correlational development is needed. In addressing some of the advanced space thermal management objectives concerning accommodating high heat fluxes in non-uniformly heated systems, a large battery of experiments 88 have been completed where local two-dimensional wall temperature variations were measured for both single-phase and two-phase flow in a single-side heated circular tube. As noted above, the results show significant axial and circumferential variations. Accurately accounting for such variations can result in optimized future advanced space, enhanced (high heat flux) thermal management systems.

Boyd, Ronald D.↗
DOE OSTI2026

Electronic Band Structures of a Germanium Halide Perovskite Semiconductor

CsGeX 3 , a class of halide perovskites, is an emergent semiconductor with ferroelectricity and potential optoelectronic properties that can be harnessed for device applications. However, measurements of the electronic structure for this class of material are still lacking. Here, in this work, we report, for the first time, the experimental band structures of CsGeI 3 , a ferroelectric halide perovskite semiconductor, through angle-resolved photoemission spectroscopy (ARPES). The crystals were cleaved along both the (110) and (111) surfaces, facilitating the observation of clear valence band dispersions in several high-symmetry momentum directions. The observed valence band is characterized by a small hole effective mass of ∼0.1m 0 at the valence band maximum, without notable spectral signatures associated with the Rashba effect. Our experimental measurements are supported by electronic structure calculations in the DFT + G0W0 framework, enabling assessment of the band orbital characteristics, dispersion, and spin-splitting. This work unveils the intrinsic electronic and transport properties of CsGeX 3 , thereby advancing the optimization of the optoelectronic properties of this class of materials.

angle-resolved photoemission spectroscopy↗
DOE OSTI2026

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗
NASA NTRS2017

Biosensor Integration Development ExMC/Canadian Space Agency Collaboration

In support of the NASA Human Research Program Exploration Medical Capability (ExMC) Element, NASA Ames Research Center (ARC) established a collaborative effort with the Canadian Space Agency (CSA). The collaboration focuses on leveraging CSA capability in the areas of biosensors and decision support that will augment future development of such components for Exploration Missions. The CSA advancement of biosensors enables NASA to focus on the integration and data management associated with these types of components through the system currently under development by the Medical Data Architecture (MDA) project. This approach has enabled the establishment of a successful collaborative working relationship between ExMC and CSA.Applying lessons learned from the fiscal year 2016 (FY16) Human Exploration Research Analog (HERA) campaign, CSA and NASA ARC developed a solution to provide real-time feedback to researchers who monitor the collection of vital signs data from a wearable Astroskin garment. The advances in the interfaces included the development of an iPad application (by CSA) to wirelessly forward the vital signs data to the MDA system, which collected the vital signs data through a receiver developed by NASA ARC. The development of these interfaces aims to provide communications between the Astroskin and the MDA system such that data may be seamlessly collected, stored and retrieved by the MDA. The first steps towards this goal were demonstrated in FY16. In FY17, ExMC will complete the first in a series of test beds that establishes a system to automate collection and management of vital sign data from the Astroskin, and other sources of data, to provide information for a crewmember to make medical decisions. In addition, the MDA Test Bed 1 will enable CSA to evaluate and optimize biosensor advancement and facilitate decision support algorithm development.

Vital signs↗
NASA NTRS2017

Biosensor Integration Development ExMC/Canadian Space Agency Collaboration

In support of the NASA Human Research Program Exploration Medical Capability (ExMC) Element, NASA Ames Research Center (ARC) established a collaborative effort with the Canadian Space Agency (CSA). The collaboration focuses on leveraging CSA capability in the areas of biosensors and decision support that will augment future development of such components for Exploration Missions. The CSA advancement of biosensors enables NASA to focus on the integration and data management associated with these types of components through the system currently under development by the Medical Data Architecture (MDA) project. This approach has enabled the establishment of a successful collaborative working relationship between ExMC and CSA.Applying lessons learned from the fiscal year 2016 (FY16) Human Exploration Research Analog (HERA) campaign, CSA and NASA ARC developed a solution to provide real-time feedback to researchers who monitor the collection of vital signs data from a wearable Astroskin garment. The advances in the interfaces included the development of an iPad application (by CSA) to wirelessly forward the vital signs data to the MDA system, which collected the vital signs data through a receiver developed by NASA ARC. The development of these interfaces aims to provide communications between the Astroskin and the MDA system such that data may be seamlessly collected, stored and retrieved by the MDA. The first steps towards this goal were demonstrated in FY16. In FY17, ExMC will complete the first in a series of test beds that establishes a system to automate collection and management of vital sign data from the Astroskin, and other sources of data, to provide information for a crewmember to make medical decisions. In addition, the MDA Test Bed 1 will enable CSA to evaluate and optimize biosensor advancement and facilitate decision support algorithm development.

Astroskin↗
DOE OSTI2025

Assessing hydrogen supply chains: An integrated review of leakage and energy efficiency studies

This paper examines hydrogen leakage and efficiency across the supply chain for liquid, gaseous, and mixed hydrogen systems. These factors are crucial for assessing hydrogen's role in mitigating emissions and facilitating a clean energy transition. Drawing on a comprehensive review of existing literature and model-based analysis, the study compiles leakage rates and efficiency metrics at each stage of the supply chain: production, storage, transmission, distribution, and end-use. These data inform system scenarios that estimate the impact of leakage on overall performance and climate benefits. The analysis also identifies persistent data gaps, particularly for liquid and mixed system configurations, and outlines priorities for future research. A comparison of hydrogen system types shows that gaseous pathways generally achieve the highest efficiencies (28 %–39 %) and the lowest leakage rates (∼4.5 %) across the supply chain. Liquid hydrogen systems, while favorable for long-distance and high-volume transport due to their higher energy density, exhibit lower efficiency (∼28 %) and a greater leakage potential (∼12 %). Mixed systems, which combine gaseous and liquid elements (e.g., pipeline transmission followed by liquefaction and truck distribution), show compounded energy losses and moderate-to-high leakage rates (6.8 %–9.4 %), highlighting trade-offs associated with added system complexity. The study highlights opportunities for technological advancements, including optimizing liquefaction, enhancing insulation for storage and transportation, and refining refueling equipment. These improvements are crucial for maximizing the climate benefits of hydrogen. The results offer actionable insights for researchers, industry, and policymakers working to develop low-leakage, high-efficiency hydrogen infrastructure.

08 HYDROGEN↗
DOE OSTI2025

Kinetics of amorphous defect phases measured through ultrafast nanocalorimetry

Recognition of the role of extended defects on local phase transitions has led to the conceptualization of the defect phase, localized thermodynamically stable interfacial states that have since been applied in a myriad of material systems to realize significant enhancements in material properties. Here, we explore the kinetics of grain boundary confined amorphous defect phases, utilizing the high temperature and scanning rates afforded by ultrafast differential scanning calorimetry to apply targeted annealing/quenching treatments at high rates capable of capturing the kinetic behavior. Four Al-based nanocrystalline alloys, including two binary systems, Al–Ni and Al–Y, and two ternary systems, Al–Mg–Y and Al–Ni–Y, are selected to probe the materials design space (enthalpy of mixing, enthalpy of segregation, chemical complexity) for amorphous defect phase formation and stability, with correlative transmission electron microscopy applied to link phase evolution and grain stability to nanocalorimetry signatures. A series of targeted isothermal annealing heat treatments is utilized to construct a Time–Temperature-Transformation curve for the Al–Ni system, from which a critical cooling rate of 2400 °C/s was determined for the grain boundary confined disordered-to-ordered transition. Finally, a thermal profile consisting of 1000 repeated annealing sequences was created to quantify the recovery of the amorphous defect phase following sequential annealing treatments, with results indicating remarkable microstructural stability after annealing at temperatures above 90% of the melting temperature. This work contributes to a deeper understanding of grain boundary localized thermodynamics and kinetics, with potential implications for the design and optimization of advanced materials with enhanced stability and performance.

Amorphous defect phases↗
DOE OSTI2025

Process intensification approach to enhancing heat and mass transfer during drying: Ultrasonic (US) assisted drying of paper and board

Drying of paper and board is conventionally achieved through alternating conduction (steam-heated cylinders) and pocket convection (heated air over the paper web surface). These conventional drying systems rely heavily on steam from fossil fuels, resulting in inefficiencies, high energy usage, and thermal losses due to surface-driven mechanisms. Here, to address these challenges, an experimental system, with in-situ drying characteristics measurements, was developed to investigate process intensification using ultrasonic-based dewatering—a volumetric, pressure-driven acoustic energy system—integrated with conventional drying. The objectives of this study are to assess the impact of ultrasonics (US) on dewatering; compare performances to conventional drying systems; identify improvements in drying rate and energy use as a function of moisture content; and gain potential insights on heat and mass transfer mechanisms during US-assisted drying. US performance was evaluated across frequencies, power levels, pulp types, and basis weights. Results show that improvements to ultrasonic applications in conjunction with convection were 30-43% in drying rate and 20-35% in drying time over continuous and intermittent applications. When combined with conduction and convection, ultrasonics yielded up to 20% improvement in both rate and time and up to 20% reduction in energy consumption. Observations support a hypothesis of extension of the constant rate period due to improved capillary flow at higher moisture content and enhancing vapor diffusion and boundary layer disruption at lower moisture contents during falling rate period. These findings will inform future modeling, simulation, design and optimization of advanced drying systems.

42 ENGINEERING↗
DOE OSTI2025

Chromium enhances the mechanical performance of 3d transition metal high entropy alloys

A comprehensive examination of the compositional effects on the deformation behavior of high entropy alloys (HEAs) was conducted through nanoindentation, indentation creep, and stress relaxation experiments at ambient temperature. The alloys investigated included NiCoFe, NiCoCr, NiCoCrFe, and NiCoCrFeMn, all of which underwent identical thermomechanical processing. From the experimental results, NiCoCr exhibited the highest maximum shear stress for dislocation nucleation (13 GPa) and nanoindentation hardness (3.8 GPa) among the alloys tested. It also showed the lowest stress sensitivity (0.02) and activation volume (3–4 b 3 ) under creep and stress relaxation conditions, indicative of its superior plastic flow properties. Density functional theory (DFT) calculations further revealed an uneven charge density and larger bonding-length variation in NiCoCr due to the presence of Cr, which increased lattice distortion, impeding dislocation movement. Furthermore, in this study, post-deformation microscopy using transmission electron microscopy (TEM) revealed a high density of stacking faults and twins in NiCoCr that effectively enhanced its creep strength. The results highlight the significance of specific elemental effects, particularly from Cr in this study, over configurational entropy effect (i.e., compositional complexity) in governing the deformation microstructure and mechanical properties of HEAs. Finally, these insights will be instrumental for the design and optimization of advanced alloys for load-bearing applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Dynamic Modeling and Simulation of a Subcritical Coal-Fired Power Plant under Load-Following Conditions

Dynamic models for power plants that capture realistic general process trends and effects of manipulated variables are needed to improve load-following, while minimizing carbon footprint. In this work, a dynamic modeling approach and simulation results for subcritical coal-fired power plant components are presented. These encompass simulation of the dynamics in the fireside, including the effects of fuel, air combustion, and the dynamics of the entire waterside and power generation sections. This model development enables the simulation and analysis of the important short and long-time scale dynamics of components such as heaters, evaporative loop, and power generation units. Furthermore, additional variables in the power generation section are introduced to improve model accuracy, extending the prediction capability of subcritical power plant models and opening new opportunities for research in operator training, optimization, and advanced model-based controller design that are based on these models. The change in process gain for different ramp rates associated with disturbance signals that affect process variables is also explored and a correlation developed. This provides opportunities to study disturbance rejection control implementation and adaptation for scenarios with such variations in ramp rates. The prediction capabilities of selected components are compared to data available in literature, with the obtained root mean squared error ranges that reflect the model performance and quality of predictions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ni-Rich Li[Ni x MnyCo 1– x – y ]O 2 Single Crystals as Superior Fast Charge Cathodes for Lithium-Ion Batteries

The utilization of single-crystal (SC) Li[Ni x MnyCo 1-x-y ]O 2 (NMC) cathodes has facilitated unparalleled performance in commercial high-energy lithium-ion batteries (LIBs). In the current study, we evaluate the application of SC cathodes in fast charge (FC)-LIBs where particle cracking is a predominant failure mechanism. Ni-rich SC-NMC samples with various compositions, sizes, and shapes are synthesized and investigated for their influence on FC performance. We reveal the necessity of utilizing smaller SCs (<1 μm) as larger sizes (>2 μm) experience significant particle-level lithium concentration gradients under FC conditions. To improve lithium transport and minimize side reactivities, we strategically expose the (104) crystal facets on the surface. Exceptional performance was observed on an optimized SC-LiNi 0.80 Mn 0.05 Co 0.15 O 2 , delivering a discharge capacity of 165 mAh/g even after 150 cycles at 6C charge. Our study not only demonstrates the promise of SC-NMC but also provides the key insights for the design and optimization of advanced cathodes for FC-LIBs.

25 ENERGY STORAGE↗
DOE OSTI2026

Ultra-thick three-dimensional interpenetrating graphene electrode architectures for high volumetric density energy storage

For electrochemical energy storage, increasing the electrode thickness is an effective approach to achieving higher energy density from a given material. However, this often compromises ion transport, leading to diminished performance. Here, in this study, we present a novel platform for fabricating complex 3D interpenetrating electrode structures via photo-polymerization 3D printing, integrated with computational structural optimization for energy storage. The platform employs an acrylate resin system infused with graphene oxide (GO), enabling high-fidelity printing of optimized porous structures and facilitating efficient electron and ion transport in ultra-thick electrodes. The optimized 3D layouts substantially enhance energy and power densities compared to conventional configurations, ensuring superior material utilization and minimal ohmic losses. Supercapacitors fabricated using this approach achieved an exceptional energy density of 4.7 Wh L−1 at a power density of 1689.0 W L−1, surpassing traditional designs. This work underscores the transformative role of structural optimization in advancing electrochemical performance and establishes a versatile pathway for developing next-generation energy storage systems with exceptional efficiency and functionality.

Wang, Zhen [University of California, Berkeley, CA↗
DOE OSTI2025

Measurement of Photons Emitted by High-Energy Charged Particles as Background in Single-Photon Resolving Image Sensors

This work introduces an advanced technique optimized for detecting photons generated by charged particles, leveraging Skipper charge coupled device (Skipper-CCD) image sensors. By analyzing background sources and detection efficiencies, the technique achieves strong agreement between experimental results and Cherenkov-based simulations. It also provides a robust framework for investigating secondary photon production in environments with high fluxes of ionizing particles, such as those anticipated in space-based astronomical instruments. These secondary photons present a critical challenge as background noise for next-generation single-photon resolving imagers used to study faint celestial objects. Furthermore, the method exhibits significant potential for broader applications, including exploring photon generation in various substrate materials and examining their transport through multiple interfaces.

Fernandez Moroni, Guillermo [Fermilab; Chicago U.,↗
DOE OSTI2025

Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films

High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.

AFM↗
DOE OSTI2024

Advanced Computational Techniques for Improving Resilience of Critical Energy Infrastructure under Cyber-Physical Attacks

In this chapter, we present recent advances in improving the resilience of cyber-physical systems, especially with regards to energy systems. We provide discussions around various types of cyber-physical events that can cause disruptions and new advances in optimization, control, and reinforcement learning (RL) to deal with the challenges posed by such cyber-physical events. The presented methods range from distributed robust optimization, autonomous and coordinated control, reinforcement learning based resilient control and topology reconfiguration in Inter-System resilient control.

Nazir, Mohammad Nawaf [BATTELLE (PACIFIC NW LAB)]↗