Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aero”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Transition Aero-Propulsive Analysis of a Tilt-Wing eVTOL Aircraft Using a Surface-Vorticity Solver

This work uses FlightStream, a surface-vorticity solver, to perform an aero-propulsive analysis on the NASA LA-8 aircraft through the transition flight regime. Aerodynamic force and moment coefficient predictions for forward and transition flight of the airframe without propulsors are compared with wind tunnel data. Powered transition cases are simulated using Conway actuator disks to model the propellers and results are compared with response surface equations derived from wind tunnel data. The approach described in the paper provides mid-fidelity solutions at a reduced computational cost compared to volumetric CFD, which allows for rapid transition flight analyses and optimization in the early design stages. The best prediction results were observed in forward flight and high-speed transition. Mid-transition results were not as close in magnitude but the trends exhibited reasonable agreement with experimental data.

Advanced Air Mobility↗
NASA NTRS2015

Atmospheric Turbulence Modeling for Aero Vehicles: Fractional Order Fits

Atmospheric turbulence models are necessary for the design of both inlet/engine and flight controls, as well as for studying coupling between the propulsion and the vehicle structural dynamics for supersonic vehicles. Models based on the Kolmogorov spectrum have been previously utilized to model atmospheric turbulence. In this paper, a more accurate model is developed in its representative fractional order form, typical of atmospheric disturbances. This is accomplished by first scaling the Kolmogorov spectral to convert them into finite energy von Karman forms and then by deriving an explicit fractional circuit-filter type analog for this model. This circuit model is utilized to develop a generalized formulation in frequency domain to approximate the fractional order with the products of first order transfer functions, which enables accurate time domain simulations. The objective of this work is as follows. Given the parameters describing the conditions of atmospheric disturbances, and utilizing the derived formulations, directly compute the transfer function poles and zeros describing these disturbances for acoustic velocity, temperature, pressure, and density. Time domain simulations of representative atmospheric turbulence can then be developed by utilizing these computed transfer functions together with the disturbance frequencies of interest.

Atmospheric Turbulence Modeling↗
NASA NTRSDate not supplied

Aero Fair Presentation

Diversity and Inclusion Outreach event to promote STEM, NASA, and Aeronautics to underrepresented middle school students in the Bay Area. Connect with the community. Engage with students to showcase NASA Ames Aeronautics and spark interest in a STEM education.

Aero Fair↗
NASA NTRSDate not supplied

Aero Fair 2022

Diversity and Inclusion Outreach event to promote STEM, NASA, and Aeronautics to underrepresented middle school students in the Bay Area. Connect with the community. Engage with students to showcase NASA Ames Aeronautics and spark interest in a STEM education.

Aero Fair 2022↗
NASA NTRSDate not supplied

Aero Fair 2022

Diversity and Inclusion Outreach event to promote STEM, NASA, and Aeronautics to underrepresented middle school students in the Bay Area. Connect with the community. Engage with students to showcase NASA Ames Aeronautics and spark interest in a STEM education.

Aero Fair 2022↗
NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Testbed Results with Energy Storage

Electrified aircraft propulsion (EAP) research is a priority of the National Aeronautics and Space Administration (NASA) for its potential to increase propulsion system efficiency, performance, and operability at the subsystem and vehicle levels while decreasing emissions. These EAP systems demand more advanced control algorithms due to increased complexity. NASA has developed a reconfigurable, hardware-in-the-loop rig to verify control algorithm performance using a sub-scale electro-mechanical system. A novel capability of this rig is the ability to test full scale EAP control algorithms on a sub-scale representation of the electro-mechanical system without turbomachinery/rotors. A novel feature is the use of a physical energy storage device within the electro-mechanical system. A dual spool, parallel hybrid-electric turbofan architecture and energy management control system is tested with the goal of verifying the ability to obtain turbomachinery model operability benefits while controlling sub-scale electro-mechanical hardware. Pre-test predictions of the turbofan model, control, and rig performance were obtained through simulation using a software model of the rig. Theoretical results showing the true performance of the turbofan model were obtained through a software simulation using full-scale mechanical shaft models. The paper compares theoretical, predicted, and actual test results from the turbofan model, energy management control and rig perspectives. The results show that the presence of sub-scale electro-mechanical hardware did not inhibit the energy management algorithm from achieving turbomachinery operability benefits.

hybrid↗
NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Testbed Results with Energy Storage

Electrified aircraft propulsion (EAP) research is a priority of the National Aeronautics and Space Administration (NASA) for its potential to increase propulsion system efficiency, performance, and operability at the subsystem and vehicle levels while decreasing emissions. These EAP systems demand more advanced control algorithms due to increased complexity. NASA has developed a reconfigurable, hardware-in-the-loop rig to verify control algorithm performance using a sub-scale electro-mechanical system. A novel capability of this rig is the ability to test full scale EAP control algorithms on a sub-scale representation of the electro-mechanical system without turbomachinery/rotors. A novel feature is the use of a physical energy storage device within the electro-mechanical system. A dual spool, parallel hybrid-electric turbofan architecture and energy management control system is tested with the goal of verifying the ability to obtain turbomachinery model operability benefits while controlling sub-scale electro-mechanical hardware. Pre-test predictions of the turbofan model, control, and rig performance were obtained through simulation using a software model of the rig. Theoretical results showing the true performance of the turbofan model were obtained through a software simulation using full-scale mechanical shaft models. The paper compares theoretical, predicted, and actual test results from the turbofan model, energy management control and rig perspectives. The results show that the presence of sub-scale electro-mechanical hardware did not inhibit the energy management algorithm from achieving turbomachinery operability benefits.

hybrid↗
DOE OSTI2024

Coupled aero-hydro-geotech real-time hybrid simulation of offshore wind turbine monopile structures

Real-time hybrid simulation (RTHS) divides a structural system into an analytical and experimental substructure. The former is based on a well-established analytical model while the latter consists of a physical model in the laboratory, for which there is not a well-established analytical model. This paper extends real-time hybrid simulation to monopile-type Offshore Wind Turbines (OWTs) to enable the investigation of their behavior considering the response of pile foundations under operational and more severe conditions. The embedded foundation and surrounding soil of the OWT are modeled physically in a soil box in the laboratory while the remaining parts of the system and loading are modeled analytically. The program OpenFAST, developed by the National Renewable Energy Laboratory (NREL), is linked to the RTHS coordinator to determine the hydrodynamic and aerodynamic loads acting on the OWT, along with modeling the dynamics of the electric power generation equipment and associated controller for the OWT. The RTHS framework along with its initial implementation and validation are described in this paper. RTHSs of a 5 MW OWT subjected to operational and more severe conditions are performed to experimentally validate the framework. The framework offers a realistic approach to investigate the behavior of OWT structures supported on monopiles. Furthermore, this approach accounts for the coupled response of the OWT structure with its foundation, while experimentally capturing the nonlinearities of the soil-foundation interaction in real-time.

17 WIND ENERGY↗
DOE OSTI2022

Aero-thermal numerical characterization of blunt fin-induced shock wave–boundary layer interaction and its control through leading-edge cooling injection

This study represents a novel evaluation of active flow control to alleviate the aerothermal penalties created by the blunt fin-induced shock wave–boundary layer interaction. The manuscript analyzes the effect of flow injection on a blunt fin-induced shock wave–boundary layer interaction via computational fluid dynamics simulations with various degrees of resolution. The impact on the mean flow topology and wall variables was investigated utilizing Reynolds-averaged Navier–Stokes simulations. Detached-eddy simulations revealed the low-frequency shock motion, shock wave–boundary layer, and horseshoe vortex interaction. The test article was exposed to two different incoming boundary layer thicknesses; the thicker boundary layer led to the appearance of larger turbulent scales. The Detached-eddy simulations revealed the time history of the shock wave–boundary layer interaction, focusing on the inception and development of the recirculated flow regions. Ultimately, spectral proper orthogonal decomposition was employed to identify the structures associated with the low-frequency shock motion caused by the shock wave–boundary layer interaction.

Lozano, Francisco (ORCID:0000000277871125)↗
DOE OSTI2021

Design, Flow Field, and Heat Transfer Characterization of the Conjugate Aero-Thermal Test Facility at NETL

A new aerothermal test facility was constructed for the purpose of studying film cooling performance in an environment that accurately simulates conjugate heat transfer characteristics that exist in engine operation. Here, this paper details the design of the facility and the plan for conducting steady state film cooling experiments to improve the understanding of conjugate heat transfer scaling from laboratory to engine conditions. The test facility consists of two separate low channels (hot gas/coolant) and each gas path has a flow conditioning section, a convergent nozzle and a test section/channel with viewports. Numerical simulations were conducted to predict flow field characteristics supporting the design of the flow loop facility. Preliminary experiments were conducted to characterize the flow field using velocity and temperature profile measurements. In addition, infrared (IR) thermography methods were developed to measure surface temperatures on the hot side of the test plate. The IR measurement methods including calibration of the IR camera is explained in detail. It was concluded that appropriate hot gas path flow conditioning could be achieved using a strainer-like tube, a perforated plate, and a honeycomb-mesh screen system upstream of the test section. Flow field measurements from preliminary experiments showed that the boundary layer profile follows the law of the wall.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Turbine Aero-Thermal Technologies for 65% Combined Cycle Efficiency (Phase I Final Report)

GE Power (GEP), a division of General Electric Company, performed a gas turbine technology development program that integrated Aerodynamic and Heat Transfer advances as an important and innovative step towards the DOE goal of 65% combined cycle efficiency. Improved efficiency will also contribute towards the reduction in the cost of electricity identified by the DOE for the US through reduced fuel consumption, and through lowering the capital cost of the generating equipment. It is currently predicted that the result of this project will enable 0.40~0.65 pt in combined cycle efficiency improvement. This technology will be directly applicable to gas turbines utilizing coal gasification processes where hydrogen-rich coal-derived synthesis gas is produced with natural gas being the developmental fuel.

03 NATURAL GAS↗
DOE OSTI2021

Low-Cost Aero Technology Demonstrations

The main focus of this work was to demonstrate the use of polymeric additive manufacturing (AM) to create tooling for both preforming and consolidation. Polymeric tooling was utilized where both modest and higher pressures are used for part consolidation. The key focus for the AM tooling development was for fabrication of complex structures such as ducting, C-channel stiffened skins, and airfoils where conventional male tooling would typically be trapped in the cured part. The AM tooling was evaluated for use as a tool master used to fabricate and re-shape deformable/re-formable mandrels based on SpinTech’s shape memory composite technology known as Smart Tooling. The AM tooling was also evaluated for use as a mold for composite infusion and consolidation. Key performance parameters were tracked for project schedule completion with each step comprising of “art to part” cycle time, cost, and model fidelity for dimensions, performance, and cost. The primary focus of this demonstration was to determine if a 50% cost reduction was achievable, for each AM tooling-set, as compared to conventional processes. UDRI leveraged project partner SpinTech, who manufactures tools and parts in these categories and thus provided a baseline regarding current best practices and provided valuable feedback during the entirety of this demonstration. This demonstration primarily focused on the use of AM tooling for fabrication of three composite component structures which are typically utilized in aircraft and comprise salient geometric features of broad interest. These components are often tooling intensive and have features requiring extraction of male tools which are usually trapped by the geometry. The three structures selected by the team included: 1) A one-piece airfoil shell comprised of compound contours where male tooling would be trapped unless the part were manufactured in two halves as is typically the case. 2) A one-piece duct used for air handling, comprised of compound contours where male tooling would be trapped unless the part were manufactured in two halves, or a washout mandrel were to be used. 3) A co-cured C-channel stiffened skin where typically C-channels would be individually manufactured and then bonded to a cured skin. The demonstration was comprised of three main tasks: • Task 1: AM Tool Feasibility Study – ensure the AM tooling meets the performance requirements as specified by SpinTech to match baseline performance. • Task 2: Complex Tool Demonstration – Fabricate tooling, preforms, and parts representative of an airfoil and duct. • Task 3: Large Aerostructure Fabrication Demonstration – Fabricate tooling, preforms, and part representative of a C-channel stiffened skin. With the conclusion of this project, a decision tree was developed to determine the key considerations necessary to determine if use of AM tooling for the three selected structures was able to attain the same quality as historically achieved on metallic tooling, while providing a significant cost reduction.

36 MATERIALS SCIENCE↗