Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aircraft Wing Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

T-Cap Pull-Off and Bending Behavior for Stitched Structure

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in largescale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Lovejoy, Andrew E.↗
NASA NTRS2016

Tension and Bending Testing of an Integral T-Cap for Stitched Composite Airframe Joints

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in large-scale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Lovejoy, Andrew E.↗
NASA NTRS2015

Experiment Design for Complex VTOL Aircraft with Distributed Propulsion and Tilt Wing

Selected experimental results from a wind tunnel study of a subscale VTOL concept with distributed propulsion and tilt lifting surfaces are presented. The vehicle complexity and automated test facility were ideal for use with a randomized designed experiment. Design of Experiments and Response Surface Methods were invoked to produce run efficient, statistically rigorous regression models with minimized prediction error. Static tests were conducted at the NASA Langley 12-Foot Low-Speed Tunnel to model all six aerodynamic coefficients over a large flight envelope. This work supports investigations at NASA Langley in developing advanced configurations, simulations, and advanced control systems.

Murphy, Patrick C.↗
NASA NTRS2011

Lateral-Directional Parameter Estimation on the X-48B Aircraft Using an Abstracted, Multi-Objective Effector Model

The problem of parameter estimation on hybrid-wing-body aircraft is complicated by the fact that many design candidates for such aircraft involve a large number of aerodynamic control effectors that act in coplanar motion. This adds to the complexity already present in the parameter estimation problem for any aircraft with a closed-loop control system. Decorrelation of flight and simulation data must be performed in order to ascertain individual surface derivatives with any sort of mathematical confidence. Non-standard control surface configurations, such as clamshell surfaces and drag-rudder modes, further complicate the modeling task. In this paper, time-decorrelation techniques are applied to a model structure selected through stepwise regression for simulated and flight-generated lateral-directional parameter estimation data. A virtual effector model that uses mathematical abstractions to describe the multi-axis effects of clamshell surfaces is developed and applied. Comparisons are made between time history reconstructions and observed data in order to assess the accuracy of the regression model. The Cram r-Rao lower bounds of the estimated parameters are used to assess the uncertainty of the regression model relative to alternative models. Stepwise regression was found to be a useful technique for lateral-directional model design for hybrid-wing-body aircraft, as suggested by available flight data. Based on the results of this study, linear regression parameter estimation methods using abstracted effectors are expected to perform well for hybrid-wing-body aircraft properly equipped for the task.

Ratnayake, Nalin A.↗
NASA NTRSDate not supplied

Design of an Acoustic Shielding Flap Concept with Prediction and Validation

As part of a NATO task group, NASA has designed a noise reduction technology called a Shielding Flap for application to a hybrid wing body aircraft concept. The design drivers and objectives for this technology are outlined in this paper. Design parameters are defined, and recently-developed NASA software for prediction of acoustic scattering is used to investigate the expected performance of the technology for a range of parameter values. Detailed scattering computational results are presented for several simulated noise sources and for many variations of the shielding flap concept. A selection of computational results is compared with experimental data collected in the NASA Langley Quiet Flow Facility. Overall, the results indicate that the Shielding Flap has strong potential to reduce aft-radiated noise, which was a primary design objective, by shielding sound from the simulated sources while also shielding sound that is scattered from the main airframe.

Propulsion Airframe Aeroacoustics↗
NASA NTRS1976

Integration of a code for aeroelastic design of conventional and composite wings into ACSYNT, an aircraft synthesis program

A comparison of program estimates of wing weight, material distribution. structural loads and elastic deformations with actual Northrop F-5A/B data is presented. Correlation coefficients obtained using data from a number of existing aircraft were computed for use in vehicle synthesis to estimate wing weights. The modifications necessary to adapt the WADES code for use in the ACSYNT program are described. Basic program flow and overlay structure is outlined. An example of the convergence of the procedure in estimating wing weights during the synthesis of a vehicle to satisfy F-5 mission requirements is given. A description of inputs required for use of the WADES program is included.

Mullen, J., Jr.↗
NASA NTRS2007

Innovative Concept for a Heavy-Load Aircraft Utilizing a Two-Dimensional Wing

Heavy-load aircraft of conventional wing-body-tail design have become very large. Excessive size of such aircraft may present problems in the manufacturing process. In addition, large wing spans may cause some difficulties in ground handling. Increasing lift loads on large span cantilever wings will also increase the strength of the wing tip vortex. The concept presented herein proposes a means for substantially increasing the lift load capability of an aircraft without increasing the overall length and span of the configuration. The concept has a rectangular wing with a relatively low span and a large chord to provide the area required for high lift. Large fuselages are attached at each wing tip to provide the volume required for heavy loading. The fuselages serve as endplates for the wing and should preclude tip flow so that two-dimensional flow might be established on the wing. Elimination of the wing tip flow should prevent the formation of a tip vortex and eliminate the tip vortex hazard to trailing aircraft. Exploratory wind tunnel tests of such an aircraft concept have been conducted. Lessons learned from these tests are discussed herein in an effort to determine the validity of the concept.

Spearman, M. Leroy↗
NASA NTRS1976

A fuselage/tank structure study for actively cooled hypersonic cruise vehicles, summary

A detailed analytical study was made to investigate the effects of fuselage cross section (circular and elliptical) and the structural arrangement (integral and nonintegral tanks) on aircraft performance. The vehicle was a 200 passenger, liquid hydrogen fueled Mach 6 transport designed to meet a range goal of 9.26 Mn (5000 NM). A variety of trade studies were conducted in the area of configuration arrangement, structural design, and active cooling design in order to maximize the performance of each of three point design aircraft: (1) circular wing-body with nonintegral tanks, (2) circular wing-body with integral tanks and (3) elliptical blended wing-body with integral tanks. Aircraft range and weight were used as the basis for comparison. The resulting design and performance characteristics show that the blended body integral tank aircraft weights the least and has the greatest range capability, however, producibility and maintainability factors favor nonintegral tank concepts.

Pirrello, C. J.↗
NASA NTRS1981

Aluminum blade development for the Mod-OA 200-kilowatt wind turbine

The rotor blade configuration, fabrication methods, analyses, operating experience, design modifications, and cost are described. Each 60-ft.-(18.3-m-) long aluminum blade used current aircraft fixed wing and rotary wing design and fabrication technologies. Structural damage, repairs, and modifications that occurred during 6500 hours of operation are summarized.

Linscott, B. S.↗
NASA NTRS2014

Wing Configuration Impact on Design Optimums for a Subsonic Passenger Transport

This study sought to compare four aircraft wing configurations at a conceptual level using a multi-disciplinary optimization (MDO) process. The MDO framework used was created by Georgia Institute of Technology and Virginia Polytechnic Institute and State University. They created a multi-disciplinary design and optimization environment that could capture the unique features of the truss-braced wing (TBW) configuration. The four wing configurations selected for the study were a low wing cantilever installation, a high wing cantilever, a strut-braced wing, and a single jury TBW. The mission that was used for this study was a 160 passenger transport aircraft with a design range of 2,875 nautical miles at the design payload, flown at a cruise Mach number of 0.78. This paper includes discussion and optimization results for multiple design objectives. Five design objectives were chosen to illustrate the impact of selected objective on the optimization result: minimum takeoff gross weight (TOGW), minimum operating empty weight, minimum block fuel weight, maximum start of cruise lift-to-drag ratio, and minimum start of cruise drag coefficient. The results show that the design objective selected will impact the characteristics of the optimized aircraft. Although minimum life cycle cost was not one of the objectives, TOGW is often used as a proxy for life cycle cost. The low wing cantilever had the lowest TOGW followed by the strut-braced wing.

Wells, Douglas P.↗
NASA NTRS2018

Multidisciplinary Design Optimization and Cruise Mach Number Study of Truss-Braced Wing Aircraft

The Subsonic Ultra Green Aircraft Research (SUGAR) Phase III was led by Dr. Rakesh K. Kapania and Dr. Joseph A. Schetz at the Multidisciplinary Analysis and Design Center for Advanced Vehicles, Department of Aerospace and Ocean Engineering, Virginia Tech, Blacksburg VA. The research was performed from December 2014 to December 2015. Three major areas were investigated: Multidisciplinary Design Optimization (MDO) studies of truss braced wing (TBW) and strut braced wing (SBW) vehicles at cruise Mach numbers of 0.7 and 0.8 for a flight mission similar to current market single aisle configurations. The performance and the characteristics of the optimized vehicles were compared to the SUGAR Phase II TBW vehicle. These results were obtained without applying any of the extended transonic aerodynamic and aeroelastic tools that will be discussed later. It was found that the cruise Mach number has a large effect on the best “truss” configuration. At Mach 0.7, an SBW has a better fuel consumption and better take-off gross weight (TOGW). However, at Mach 0.8, the TBW is superior because the jury strut aids in satisfying the flutter constraint; Two-dimensional, steady, transonic aerodynamic analysis of the Boeing Airfoil J (BACJ) airfoil was performed for a range of thickness ratios, Mach numbers and lift coefficients. Reynolds-averaged Navier-Stokes (RANS) equations were solved to obtain the lift-curve slope, wave drag coefficient, the location of the center of pressure and to predict the separation at the trailing edge, which may lead to buffeting. One of the goals was to develop a database of lift-curve slope and the location of center of pressure, which could be used in a transonic aeroelastic analysis. Another goal was to compare the wave drag coefficients to those predicted by Lock’s fourth-power law and also to compare the transonic effects obtained from RANS simulations to those predicted by the Korn equations. A third goal was to develop a buffet boundary, which can be integrated into the MDO framework to prevent the optimized designs from probable buffeting; A state-space transonic aeroelastic analysis tool was developed, which can incorporate the nonlinear transonic effects in the unsteady aerodynamics but is yet computationally cheap when used within the VT MDO framework. The aeroelastic analysis uses Leishman- Beddoes (LB) indicial functions, which generated a state-space representation of the aeroelastic system. The indicial functions allow the incorporation of data for steady lift-curve slope and location of the center of pressure. Thus, the steady transonic effects are included, and the unsteady aerodynamic responses are a linearization about the steady results. The aeroelastic approach discretizes the wing into numerous strips, which results in a large eigenvalue problem as each strip has eight augmented aerodynamic states as per the LB theory. Thus, to reduce the computation expense, a reduced order model (ROM) was developed. The approach was validated using a few examples.

Kapania, Rakesh K.↗
NASA NTRS2016

Conceptual Design and Structural Optimization of NASA Environmentally Responsible Aviation (ERA) Hybrid Wing Body Aircraft

Simultaneously achieving the fuel consumption and noise reduction goals set forth by NASA's Environmentally Responsible Aviation (ERA) project requires innovative and unconventional aircraft concepts. In response, advanced hybrid wing body (HWB) aircraft concepts have been proposed and analyzed as a means of meeting these objectives. For the current study, several HWB concepts were analyzed using the Hybrid wing body Conceptual Design and structural optimization (HCDstruct) analysis code. HCDstruct is a medium-fidelity finite element based conceptual design and structural optimization tool developed to fill the critical analysis gap existing between lower order structural sizing approaches and detailed, often finite element based sizing methods for HWB aircraft concepts. Whereas prior versions of the tool used a half-model approach in building the representative finite element model, a full wing-tip-to-wing-tip modeling capability was recently added to HCDstruct, which alleviated the symmetry constraints at the model centerline in place of a free-flying model and allowed for more realistic center body, aft body, and wing loading and trim response. The latest version of HCDstruct was applied to two ERA reference cases, including the Boeing Open Rotor Engine Integration On an HWB (OREIO) concept and the Boeing ERA-0009H1 concept, and results agreed favorably with detailed Boeing design data and related Flight Optimization System (FLOPS) analyses. Following these benchmark cases, HCDstruct was used to size NASA's ERA HWB concepts and to perform a related scaling study.

Quinlan, Jesse R.↗
NASA NTRSDate not supplied

Pilot Controls for a Hybrid Turbine-Electric 17 Engine Aircraft

NASA is exploring the development of a 180-passenger subsonic single engine aft turbine aircraft where the aft turbine provides electric power in a hybrid design to wing mounted electric engines. A pilot-in-the-loop study was conducted at Langley Research Center in Hampton, Virginia to explore the design of a flight deck for the hybrid electric aircraft with 16 wing fans and an aft mounted turbine engine. Current flight deck designs provide control inceptors for each propulsion engine and display of all engine parameters for all primary aircraft engines. Automation trends and increasing automation in flight controls and throttle controls indicate less controls instead of more. The design team researched state-of-the-art and recommended study of three, two, and one throttle levers. Engine displays were researched and two were recommended for initial evaluation. 16 airline pilots evaluated the three throttle configurations and two engine display options. Engine failures for known probable indications were evaluated against all throttle and display configurations. This included one, four symmetric, eight non-symmetric, and sixteen momentary electric engine failures with the loss of the aft turbine. The turbine engine was evaluated for complete and partial failure during critical phases of takeoff as well as enroute. This paper details the pilot study including pilot comments supporting the potential for increased automation and a single throttle control. Detailed recommendations are provided for a novel single throttle control and additional pilot controls to support selection of engines during start, shutdown, and engine troubleshooting procedures. This design deviates significantly from current practice of providing throttles for each propulsion engine. Engine display recommendations are provided based on pilot feedback during a guided post-evaluation interview. Recommendations for future study are documented with supporting research and current observations about upcoming flight deck certifications.

autothrottle↗
NASA NTRSDate not supplied

Pilot Controls for a Hybrid Turbine-Electric 17-Engine Aircraft

NASA is exploring the development of a 180-passenger subsonic single engine aft turbine aircraft where the aft turbine provides electric power in a hybrid design to wing mounted electric engines. A pilot-in-the-loop study was conducted at Langley Research Center in Hampton, Virginia to explore the design of a flight deck for the hybrid electric aircraft with 16 wing fans and an aft mounted turbine engine. Current flight deck designs provide control inceptors for each propulsion engine and display of all engine parameters for all primary aircraft engines. Automation trends and increasing automation in flight controls and throttle controls indicate less controls instead of more. The design team researched state-of-the-art and recommended study of three, two, and one throttle levers. Engine displays were researched and two were recommended for initial evaluation. 16 airline pilots evaluated the three throttle configurations and two engine display options. Engine failures for known probable indications were evaluated against all throttle and display configurations. This included one, four symmetric, eight non-symmetric, and sixteen momentary electric engine failures with the loss of the aft turbine. The turbine engine was evaluated for complete and partial failure during critical phases of takeoff as well as enroute. This presentation details the pilot study including pilot comments supporting the potential for increased automation and a single throttle control. Detailed recommendations are provided for a novel single throttle control and additional pilot controls to support selection of engines during start, shutdown, and engine troubleshooting procedures. This design deviates significantly from current practice of providing throttles for each propulsion engine. Engine display recommendations are provided based on pilot feedback during a guided post-evaluation interview. Recommendations for future study are documented with supporting research and current observations about upcoming flight deck certifications.

autothrottle↗
NASA NTRS1989

Evaluation of a strain-gage load calibration on a low-aspect-ratio wing structure at elevated temperature

The environmental aspect of elevated temperature and its relationship to the science of strain gage calibrations of aircraft structures are addressed. A section of a wing designed for a high-speed aircraft structure was used to study this problem. This structure was instrumented with strain gages calibrated at both elevated and room temperatures. Load equations derived from a high-temperature load calibration were compared with equations derived from an identical load calibration at room temperature. The implications of the high temperature load calibration were studied from the viewpoint of applicability and necessity. Load equations derived from the room temperature load calibration resulted in generally lower equation standard errors than equations derived from the elevated temperature load calibration. A distributed load was applied to the structure at elevated temperature and strain gage outputs were measured. This applied load was then calculated using equations derived from both the room temperature and elevated temperature calibration data. It was found that no significant differences between the two equation systems existed in terms of computing this applied distributed load, as long as the thermal shifts resulting from thermal stresses could be identified. This identification requires a heating of the structure. Therefore, it is concluded that for this structure, a high temperature load calibration is not required. However, a heating of the structure is required to determine thermal shifts.

Reardon, Lawrence F.↗
NASA NTRS1988

Large scale prop-fan structural design study. Volume 1: Initial concepts

In recent years, considerable attention has been directed toward improving aircraft fuel consumption. Studies have shown that the inherent efficiency advantage that turboprop propulsion systems have demonstrated at lower cruise speeds may now be extended to the higher speeds of today's turbofan and turbojet-powered aircraft. To achieve this goal, new propeller designs will require features such as thin, high speed airfoils and aerodynamic sweep, features currently found only in wing designs for high speed aircraft. This is Volume 1 of a 2 volume study to establish structural concepts for such advanced propeller blades, to define their structural properties, to identify any new design, analysis, or fabrication techniques which were required, and to determine the structural tradeoffs involved with several blade shapes selected primarily on the basis of aero/acoustic design considerations. The feasibility of fabricating and testing dynamically scaled models of these blades for aeroelastic testing was also established. The preliminary design of a blade suitable for flight use in a testbed advanced turboprop was conducted and is described in Volume 2.

Billman, L. C.↗
NASA NTRS1988

Large scale prop-fan structural design study. Volume 2: Preliminary design of SR-7

In recent years, considerable attention has been directed toward improving aircraft fuel consumption. Studies have shown that the inherent efficiency advantage that turboprop propulsion systems have demonstrated at lower cruise speeds may now be extended to the higher speeds of today's turbofan and turbojet-powered aircraft. To achieve this goal, new propeller designs will require features such as thin, high speed airfoils and aerodynamic sweep, features currently found only in wing designs for high speed aircraft. This is Volume 2 of a 2 volume study to establish structural concepts for such advanced propeller blades, to define their structural properties, to identify any new design, analysis, or fabrication techniques which were required, and to determine the structural tradeoffs involved with several blade shapes selected primarily on the basis of aero/acoustic design considerations. The feasibility of fabricating and testing dynamically scaled models of these blades for aeroelastic testing was also established. The preliminary design of a blade suitable for flight use in a testbed advanced turboprop was conducted and is described.

Billman, L. C.↗
NASA NTRS1991

An assessment of tailoring of lightning protection design requirements for a composite wing structure on a metallic aircraft

The Navy A-6E aircraft is presently being modified with a new wing which uses graphite/epoxy structures and substructures around a titanium load-bearing structure. The ability of composites to conduct electricity is less than that of aluminum. This is cause for concern when the wing may be required to conduct large lightning currents. The manufacturer attempted to solve lightning protection issues by performing a risk assessment based on a statistical approach which allows relaxation of the wing lightning protection design levels over certain locations of the composite wing. A sensitivity study is presented designed to define the total risk of relaxation of the design levels.

Harwood, T. L.↗