Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analog computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1969

The Fraunhofer line discriminator: An airborne fluorometer

An experimental Fraunhofer Line Discriminator (FLD) can differentiate and measure solar-stimulated luminescence when viewed against a background of reflected light. Key elements are two extremely sensitive photomultipliers, two glass-spaced Fabry-Perot filters having a bandwidth less than 1 A, and an analog computer. As in conventional fluorometers, concentration of a fluorescent substance is measured by comparison with standards. Quantitative use is probably accurate only at low altitudes but detection of luminescent substances should be possible from any altitude. Applications of the present FLD include remote sensing of fluorescent dyes used in studies of current dynamics. The basic technique is applicable to detection of oil spills, monitoring of pollutants, and sensing over land areas.

Stoertz, G. E.↗
NASA NTRS1972

Hypersonic and transonic buzz measurements on the lower pitch flap of the M2-F2 lifting entry configuration

Free-oscillation damping measurements at hypersonic and transonic Mach numbers are presented for the lower pitch flap of the M2-F2 reentry vehicle. For the flow and model conditions tested, the damping measurements indicate the absence of hypersonic buzz instability for flap rotation frequencies of 47.3 Hz, 153 Hz, and 360 Hz, the presence of transonic buzz for 47.3 Hz flap, and the absence of transonic buzz for a 115 Hz flap. There are not enough flap damping data for an error estimate based on repeatability, but a partial damping calibration is presented in which an analog computer simulation of random flap response for a known flap damping is fed into the autocorrelation computer and filter combination used for most of the damping measurements.

Warner, R. W.↗
NASA NTRS1972

Gas-injection-start and shutdown characteristics of a 2-kilowatt to 15-kilowatt Brayton power system

Two methods of starting the Brayton power system have been considered: (1) using the alternator as a motor to spin the Brayton rotating unit (BRU), and (2) spinning the BRU by forced gas injection. The first method requires the use of an auxiliary electrical power source. An alternating voltage is applied to the terminals of the alternator to drive it as an induction motor. Only gas-injection starts are discussed in this report. The gas-injection starting method requires high-pressure gas storage and valves to route the gas flow to provide correct BRU rotation. An analog computer simulation was used to size hardware and to determine safe start and shutdown procedures. The simulation was also used to define the range of conditions for successful startups. Experimental data were also obtained under various test conditions. These data verify the validity of the start and shutdown procedures.

Cantoni, D. A.↗
NASA NTRS1971

Parameter region for proper operation of a multifilter phase-lock loop.

Parameter regions for proper operation of multifilter phase-lock loops used for demodulation are determined utilizing digital and analog computers. Experimental models are used to study these regions of proper operation. Generalized state models are developed for the multifilter phase-lock loop.

Carden, F.↗
NASA NTRS1972

A ten-stage electrostatic depressed collector for improving klystron efficiency.

A ten-stage electrostatic depressed collector, designed with the aid of an analog computer, was tested on a 1-kW CW 750-MHz klystron. Excellent correlation was achieved between computed and measured performance under varying conditions of RF drive. At full RF power output approximately 60 per cent of the spent beam energy was recovered by use of the depressed collector. The net power conversion efficiency of the tube was raised from its undepressed value of 54.3 per cent to approximately 70.9 per cent. At one-half full power output, a collector efficiency of 70 per cent was measured. At zero RF power output collector efficiency was 80 per cent. To achieve these results it was necessary to install a small focusing coil between the final drift tube and the collector. No spurious oscillations or instabilities were detected when collector depression was employed, nor was electron backstreaming increased significantly. Intentional short circuiting of adjacent collector electrode pairs was shown to cause only minor degradation in collector performance.

Neugebauer, W.↗
NASA NTRS1972

Analog analysis of a tracked air-cushion vehicle.

The dynamics of tracked air-cushion vehicles considered for high-speed ground transportation systems are examined using a vehicle model represented by a one-degree-of-freedom system. The respective equations of motion are derived, and the control system is discussed. The equations obtained for the cushion are solved using an analog computer. The computer showed the effect of the control technique on the relative motion between vehicle and guideway.

Leatherwood, J. D.↗
NASA NTRS1973

Video enhancement of X-ray and neutron radiographs

System was devised for displaying radiographs on television screen and enhancing fine detail in picture. System uses analog-computer circuits to process television signal from low-noise television camera. Enhanced images are displayed in black and white and can be controlled to vary degree of enhancement and magnification of details in either radiographic transparencies or opaque photographs.

Vary, A.↗
NASA NTRS1972

Advanced study of video signal processing in low signal to noise environments

A nonlinear analysis of a multifilter phase-lockloop (MPLL) by using the method of harmonic balance is presented. The particular MPLL considered has a low-pass filter and a band-pass filter in parallel. An analytic expression for the relationship between the input signal phase deviation and the phase error is determined for sinusoidal FM in the absence of noise. The expression is used to determine bounds on the proper operating region for the MPLL and to investigate the jump phenomenon previously observed. From these results the proper modulation index, modulating frequency, etc. used for the design of a MPLL are determined. Data for the loop unlock boundary obtained from the theoretical expression are compared to data obtained from analog computer simulations of the MPLL.

Carden, F.↗
NASA NTRS1972

Model reference adaptive systems some examples.

A direct design method is derived for several single-input single-output model reference adaptive systems (M.R.A.S.). The approach used helps to clarify the various steps involved in a design, which utilizes the hyperstability concept. An example of a multiinput, multioutput M.R.A.S. is also discussed. Attention is given to the problem of a series compensator. It is pointed out that a series compensator which contains derivative terms must generally be introduced in the adaptation mechanism in order to assure asymptotic hyperstability. Results obtained by the simulation of a M.R.A.S. on an analog computer are also presented.

Landau, I. D.↗
NASA NTRS1973

Prior-to-failure extension of flaws under monotonic and pulsating loadings.

An equation governing the prior-to-failure crack propagation is proposed. For a rate-sensitive solid containing a two-dimensional crack and subject to the tensile mode of fracture the differential equations are integrated numerically for loads increasing monotonically in time. The resulting integral curves of load vs crack length and length vs time indicate that the growth of cracks in the subcritical range is strongly rate-dependent. The fatigue growth, viewed as a sequence of slow growth periods, is simulated on an EAI 380 analog computer. The fourth-power law proposed by Paris is confirmed only within certain range of high-cycle fatigue propagation and for a rate-insensitive solid. Otherwise, i.e., for a more pronounced rate dependence induced by viscosity of a solid and/or in the proximity of the final instability point, the growth is markedly enhanced.

Wnuk, M. P.↗
NASA NTRS1973

Precise attitude control of the Stanford relativity satellite.

A satellite being designed by the Stanford University to measure (with extremely high precision) the effect of General Relativity is described. Specifically, the satellite will measure two relativistic precessions predicted by the theory: the geodetic effect (6.9 arcsec/yr), due solely to motion about the earth, and the motional effect (0.05 arcsec/yr), due to rotation of the earth. The gyro design requirements, including the requirement for precise attitude control and a dynamic model for attitude control synthesis, are discussed. Closed loop simulation of the satellite's natural dynamics on an analog computer is described.

Bull, J. S.↗
NASA NTRS1975

Optical communication channel simulator system

Optical transmission link is simulated by positioning linear optical modulator between optical carrier source and receiver for carrier. Optical modulator is driven by analog signal, derived from analog computer circuit, having random variations indicative of characteristics of transmission link.

Fitzmaurice, M. W.↗
NASA NTRS1973

Design for pressure regulating components

The design development for Pressure Regulating Components included a regulator component trade-off study with analog computer performance verification to arrive at a final optimized regulator configuration for the Space Storable Propulsion Module, under development for a Jupiter Orbiter mission. This application requires the pressure regulator to be capable of long-term fluorine exposure. In addition, individual but basically identical (for purposes of commonality) units are required for separate oxidizer and fuel pressurization. The need for dual units requires improvement in the regulation accuracy over present designs. An advanced regulator concept was prepared featuring redundant bellows, all metallic/ceramic construction, friction-free guidance of moving parts, gas damping, and the elimination of coil springs normally used for reference forces. The activities included testing of actual size seat/poppet components to determine actual discharge coefficients and flow forces. The resulting data was inserted into the computer model of the regulator. Computer simulation of the propulsion module performance over two mission profiles indicated satisfactory minimization of propellant residual requirements imposed by regulator performance uncertainties.

Wichmann, H.↗
NASA NTRS1974

Force sharing in high-power parallel servo-actuators

The various existing force sharing schemes were examined by conducting a literature survey. A list of potentially applicable concepts was compiled from this survey, and a brief analysis was then made of each concept, which resulted in two competing schemes being selected for in-depth evaluation. A functional design of the equalization logic for the two schemes was undertaken and specific space shuttle application was chosen for experimental evaluation. The application was scaled down so that existing hardware could be utilized. Next, an analog computer study was conducted to evaluate the more important characteristics of the two competing force sharing schemes. On the basis of the computers study, a final configuration was selected. A load simulator was then designed to evaluate this configuration on actual hardware.

Neal, T. P.↗
NASA NTRS1974

Analysis of self-oscillating dc-to-dc converters

The basic operational characteristics of dc-to-dc converters are analyzed along with the basic physical characteristics of power converters. A simple class of dc-to-dc power converters are chosen which could satisfy any set of operating requirements, and three different controlling methods in this class are described in detail. Necessary conditions for the stability of these converters are measured through analog computer simulation whose curves are related to other operational characteristics, such as ripple and regulation. Further research is suggested for the solution of absolute stability and efficient physical design of this class of power converters.

Burger, P.↗
NASA NTRS1975

Redundant actuator development program

Two concepts of redundant secondary actuator mechanization, applicable to future advanced flight control systems, were studied to quantitatively assess their design applicability to an AST. The two actuator concepts, a four-channel, force summed system and a three-channel, active/standby system have been developed and evaluated through analysis, analog computer simulation, and piloted motion simulation. The quantitative comparison of the two concepts indicates that the force summed concept better meet performance requirements, although the active/standby is superior in other respects. Both concepts are viable candidates for advanced control application dependent on the specific performance requirements.

Chenoweth, C. C.↗
NASA NTRS1975

Analysis of a stability valve system for extending the dynamic range of a supersonic inlet

A stability valve system designed for a full-scale, flight, supersonic, mixed-compression inlet was modeled dynamically by using analog computer techniques. The system uses poppet valves mounted in the inlet cowl to bypass airflow and augments the inlet shock position control system by preventing unstarts caused by high-frequency perturbations. The model was used as a design aid to investigate the effects of varying both the physical configurations of the valve and the flight and wind tunnel conditions. Results of the analysis indicate that the stability valve will provide a bandpass operation of 1 hertz to 17 hertz.

Webb, J. A., Jr.↗
NASA NTRS1975

Analysis of a class of pulse modulated dc-to-dc power converters

The basic operational characteristics of dc-to-dc converters are analyzed. The basic physical characteristics of power converters are identified. A simple class of dc-to-dc power converters is chosen which could satisfy any set of operating requirements. Three different controlling methods in this class are described in detail. Necessary conditions for the stability of these converters are measured through analog computer simulation. These curves are related to other operational characteristics, such as ripple and regulation. Finally, further research is suggested for the solution of the physical design of absolutely stable, reliable, and efficient power converters of this class.

Burger, P.↗