Search NASA⌕ Search

SEARCH · Search NASA

Results for “Angle Of Arrival”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

F-16E program overview and wind tunnel/flight correlation

Correlation is defined in three different ways: comparisons of wind tunnel and/or theory with flight results; detailed studies of total vehicle drag from wind tunnel and flight tests; and attempts to understand the fundamental mechanisms of fluid flows associated with aircraft components in specific areas of the flight environment. The F-16E configuration is an outgrowth of studies conducted to produce a refined fighter wing design. Several iterations required to arrive at the combination of wing planform, camber, and twist which gives near optimum lift, drag, and high-angle-of-attack stability. Theoretical analyses were backed up by extensive experimental data to validate the design and are presented

Madsen, A. P.↗
NASA NTRS1987

Summary of paper: Area navigation implementation for a microcomputer-based Loran-C receiver

The development of an area navigation program and the implementation of this software on a microcomputer-based Loran-C receiver to provide high-quality, practical area navigation information for general aviation are described. This software provides range and bearing angle to a selected waypoint, cross-track error, course deviation indication (CDI), ground speed, and estimated time of arrival at the waypoint. The range/bearing calculation, using an elliptical Earth model, provides very good accuracy; the error does not exceed more than -.012 nm (range) or 0.09 degree (bearing) for a maximum range to 530 nm. The alpha-beta filtering is applied in order to reduce the random noise on Loran-C raw data and in the ground speed calculation. Due to alpha-beta filtering, the ground speed calculation has good stability for constant or low-accelerative flight. The execution time of this software is approximately 0.2 second. Flight testing was done with a prototype Loran-C front-end receiver, with the Loran-C area navigation software demonstrating the ability to provide navigation for the pilot to any point in the Loran-C coverage area in true area navigation fashion without line-of-sight and range restriction typical of VOR area navigation.

Oguri, Fujiko↗
NASA NTRS2003

Energetic Particle Propagation in the Inner Heliosphere as Deduced from Low Frequency (less than 100 kHz) Observations of Type III Radio Bursts

Solar energetic particle (SEP) events are well-associated with solar flares. It is observed that the delay between the time of the flare and the first-arriving particles at a spacecraft increases with increasing difference between the flare longitude and the footpoint of the field line on which the spacecraft is located. This difference we call the "connection angle" and can be as large as approximately 120 deg. Recently it has been found that all SEP events are preceded by type III radio bursts. These bursts are plasma emission caused by the propagation of 2-50 keV flare electrons through the solar corona and into the solar wind. The drift of these type III radio bursts to lower and lower frequencies enables the propagation of the flare electrons to be traced from the Sun to about 1 AU. We have made an extensive analysis of the type III bursts associated with greater than 20 MeV proton events and find that, in most cases, the radio emission extends to the local plasma frequency when the energetic particles arrive within a few hours of the flare. We conclude that this emission at the lowest possible frequency is generated close to the spacecraft. We then use the time from when the burst started at the Sun to when it reached the local plasma frequency to infer the time it took the radio producing electrons to travel to the spacecraft. We find that these delay times are organized by the connection angle and correlate with the proton delay times. We also find that the differences between the radio delays at Wind and Ulysses are matched by differences in the relative arrival times of the energetic particles at the two spacecraft. The consistent timing between the relative arrival times of energetic electrons and protons and the start of the lowest frequency radio emissions suggests that the first arriving particles of both species are accelerated as part of the flare process and that they propagate to the spacecraft along trajectories similar to those of the lower energy flare electrons. To be detected by observers at locations distant from the nominal field lines originating in the flaring regions the particles must undergo lateral transport. The continuity of the radio bursts suggests that the cross-field transport may occur in the interplanetary medium.

Cane, H. V.↗
NASA NTRS2003

Aerocapture navigation at Neptune

A proposed Neptune orbiter Aerocapture mission will use solar electric propulsion to send an orbiter to Neptune. Navigation feasibility of direct-entry aerocapture for orbit insertion at Neptune is shown. The navigation strategy baselines optical imaging and (delta)VLBI measurement in order to satisfy the flight system's atmosphere entry flight path angle, which is targeted to enter Neptune with an entry flight path angle of -11.6 . Error bars on the entry flight path angle of plus/minus0.55 (3(sigma)) are proposed. This requirement can be satisfied with a data cutoff 3.2 days prior to arrival. There is some margin in the arrival template to tighten (i.e. reduce) the entry corridor either by scheduling a data cutoff closer to Neptune or alternatively, reducing uncertainties by increasing the fidelity of the optical navigation camera.

interplanetary navigation↗
DOE OSTI2020

Stress effects on flow and transport in three-dimensional fracture networks

We investigate the effects of various external stress regimes on fracture apertures, fluid flow, and solute transport in three-dimensional fracture networks. We use well-established geomechanics equations coupled with discrete fracture network modeling to characterize changes in primary flow paths within a complex network as a function of stress magnitude and orientation. These changes manifest in the alterations of the fluid flow field and are measured in terms of Eulerian and Lagrangian flow observables including solute transport, which is a key problem in many hydrologic applications. Changes in primary flow paths affect the solute transport in the network by promoting anomalously early arrival or long tailing behavior. However, early time arrival is not ubiquitous in anisotropically stressed networks and in most cases there is a delayed arrival of solute, which is attributed to (i) the presence of low-velocity zones normal to the flow direction, (ii) the angle between flow direction and major compressive principal stress directions, and (iii) changes in the primary flow paths (i.e., increases in tortuosity and active network structure). Overall, flows become more channelized in anisotropically stressed fracture networks than in unstressed and isotropically stressed networks.

58 GEOSCIENCES↗
NASA NTRS1978

Effect of aerosols on the estimation of total ozone in an atmospheric column from the measurements of its ultraviolet radiance

The problem of estimating the total ozone amount of an atmospheric column in the presence of stratospheric and tropospheric aerosols is studied by means of simulated spectral measurements for the five-wavelength Nimbus 4 BUV configuration and the six-wavelength Nimbus G TOMS configuration, and by analyzing such measurements with appropriate total ozone estimation procedures. The simulated spectral measurements were generated for forty different atmospheric models arrived at by varying the total ozone content and various aerosol parameters. A total of ten different values of the solar zenith angle and eight different values of the Lambert reflectivity of the underlying surface were used. It was found that the values of total ozone in an atmospheric column estimated by the five-wavelength procedure can be in error by about + or -2% as a result of particulate contamination encountered in the terrestrial atmosphere under average conditions. Errors due to tropospheric particulate contamination can be reduced significantly by taking appropriate advantage of the additional spectral measurement offered by the Nimbus G TOMS instrument.

Dave, J. V.↗
NASA NTRS1990

A conflict analysis of 4D descent strategies in a metered, multiple-arrival route environment

A conflict analysis was performed on multiple arrival traffic at a typical metered airport. The Flow Management Evaluation Model (FMEM) was used to simulate arrival operations using Denver Stapleton's arrival route structure. Sensitivities of conflict performance to three different 4-D descent strategies (clear-idle Mach/Constant AirSpeed (CAS), constant descent angle Mach/CAS and energy optimal) were examined for three traffic mixes represented by those found at Denver Stapleton, John F. Kennedy and typical en route metering (ERM) airports. The Monte Carlo technique was used to generate simulation entry point times. Analysis results indicate that the clean-idle descent strategy offers the best compromise in overall performance. Performance measures primarily include susceptibility to conflict and conflict severity. Fuel usage performance is extrapolated from previous descent strategy studies.

Izumi, K. H.↗
NASA NTRS1972

Terminal-area flight procedures and route design for supersonic transport New York-transatlantic operations

The results of an analytical investigation of two departure and arrival transition procedures between John F. Kennedy International Airport and projected North Atlantic track systems for supersonic transport (SST) operations are presented. The procedures studied were: (1) separated departure and arrival transition routes with departures made at supersonic speeds, and (2) superimposed departure and arrival routes with departures restricted to subsonic speed until the airplane is on the track system. For both procedures, transition routes with intercept angles of 30 deg to 90 deg to both six-and four-track systems were investigated. Track spacings of 30 and 60 nautical miles were studied.

Sawyer, R. H.↗
NASA NTRS2014

Trajectory Prediction Accuracy and Error Sources for Regional Jet Descents: Results of a 2010 Flight Trial at Denver International Airport using SkyWest Revenue Flights - Part II

The Efficient Descent Advisor (EDA) controller automation tool generates trajectory-based speed, path, and altitude-profile advisories to facilitate efficient, continuous descents into congested terminal airspace. While prior field trials have assessed the trajectory prediction accuracy for large jet (i.e., Boeing and Airbus) types, smaller (i.e., regional and business) jet types present unique challenges involving different descent procedures and Flight Management System (FMS) capabilities. This paper quantifies the trajectory prediction accuracy for small jet revenue flight descents based on SkyWest Canadair Regional Jet 200, 700, and 900 aircraft arrivals to Denver in the fall of 2010. Post flight test data analysis and SkyWest pilot interviews uncovered unexpected variation between flight crews due to different interpretations of (1) which fixed flight path angle (FPA) to fly based on the flight trial procedure and (2) how to fly the descent to achieve the target FPA. Pilot reports were used to select a subset of flights where pilots indicated an FPA according to the flight trial procedure to remove the unexpected variation due to (1) to focus on (2). Results for the subset for en-route descents, from prior to top of descent to the meter fix 30 to 130 nmi downstream, indicate that aircraft arrived to the meter fix six seconds early with about a twelve second standard deviation. Large FPA errors up to one degree relative to the EDA flight trial procedure were detected after the flight trial as a characteristic of the unexpected variation. It is recommended that quantitative validation be performed during future flight trials so that experimental procedures can be adjusted if unexpected results are detected.

Field Test Results↗
NASA NTRS2020

Design and Analysis of V-Groove Passive Cryogenic Radiators for Space-borne Telescopes & Instruments

V-groove passive radiators are extremely efficient passive designs to thermally isolate a cryogenic telescope or instrument from warm environments in space, like the Sun, Earth, Moon or Spacecrafts. Compared to traditional multi-layer insulation blankets employed for thermal isolation, the V-Groove radiators provide as much as an order of magnitude improvement. The V-Groove design typically constitutes three low emissivity, lightweight and thin aluminized Mylar/Kapton sheets angled from each other by just few degrees. These successively reflect heat from warmer shields to space via their angular openings, thus minimizing heat flow into the cryogenic system. Thermal analysis of these V-Groove radiators is typically performed by sophisticated thermal software that uses hundreds of thousands of rays to simulate radiative heat flow between successive shields via reflections, which can be very time & resource intensive. We have arrived at very simple closed form equations to predict the thermal behavior of these radiators, that includes their radiative heat transfer factors and temperatures as a function of their basic thermo-optical properties and inter-shield angles. These predictions can be done by hand calculators or in spreadsheet tools like MS-Excel. They compare very well to those from sophisticated computer programs. The ease in the use of these simple equations allow for instantaneous predictions of cryogenic temperatures and their trends for design options and trade studies. A case study of this was utilized for the telescope project that is currently being designed for an all sky spectral survey of the universe. This paper will describe the derivations of these equations, their comparison with computer software results and their applicability for current and future cryogenic space telescope and instrument missions

Bhandari, Pradeep↗
NASA NTRS1990

A polar orbit for the Mars Global Network Mission

The purpose of the Global Network Mission (GNM) is to deploy simple landers on the Martian surface in late 1998. The objective is to create a globally distributed network of ground stations which will collect environmental data, perhaps for as long as several years. The GNM presents unique mission design challenges, which are addressed by the following essay. The GNM mission concept calls for two carrier spacecraft, each equipped with a number of simple landers. Some of the landers may be deployed from approach, either to reduce carrier mass prior to orbit insertion, or to reach latitudes not available from the carrier orbit. The remaining landers are deployed from orbit. One configuration for the Global Network Mission was proposed in a report from the Exploration Precursors Task Team to the Office of Space Science and Applications. This formed the basis of a previous orbit design for the GNM. This mission scenario is used as a point of reference, but results from the current study are generally applicable to a wide range of GNM mission variants. The analysis concluded that a 1/5 sol, polar orbit with a periapse altitude of 275 km offers the best circumstances for orbital deployment of the Global Network Mission landers. It allows easy polar access at nominal entry angles, and global dispersal of landing sites at lighting angles suitable for descent imaging. The polar orbit allows the option of deploying all the landers from orbit. A wait interval of 160 days after arrival is required before deployment can commence.

Knocke, Philip↗
NASA NTRS1972

Feasibility study of a 110 watt per kilogram lightweight solar array system

An investigation of the feasibility of a solar array panel subsystem which will produce 10,000 watts of electrical output at 1 A.U. with an overall beginning-of-life power-to-weight ratio of at least 110 watt/kg is reported. A description of the current baseline configuration which meets these requirements is presented. A parametric analysis of the single boom, two blanket planar solar array system was performed to arrive at the optimum system aspect ratio. A novel concept for the stiffening of a lightweight solar array by canting the solar cell blankets at a small angle to take advantage of the inherent in-plane stiffness to increase the symmetric out-of-plane frequency is introduced along with a preliminary analysis of the stiffening effect. A comparison of welded and soldered solar cell interconnections leads to the conclusion that welding is required on this ultralightweight solar array. The use of a boron/aluminum composite material in a BI-STEM type deployable boom is investigated as a possible advancement in the state-of-the-art.

Shepard, N. F.↗
DOE OSTI2023

Neutron Calibration Studies for the SuperCDMS SNOLAB Experiment

My time at Fermilab has been dedicated to advancing the field of dark matter detection through my contributions to the SuperCDMS collaboration. The first project involved the development and testing of a delivery system for a Cf-252 neutron source to calibrate the SuperCDMS silicon and germanium detectors. Subsequently, I focused on parametrizing the detectors' instrumental response by optimizing a plastic scintillator backing array to measure the scattering angle of a collimated neutron beam. The Monte Carlo simulation I designed provided insights into the detection efficiency of the array, and the best-fit design I arrived at for the scattering counters will be implemented into the final array. Additionally, I assembled a muon detector with legacy hardware to enhance the ability of the calibration experiment to reduce dark current and false signals. As my work nears completion, I am confident that these contributions will significantly enhance the precision and reliability of the SuperCDMS experiment, pushing the boundaries of our understanding of dark matter and contributing to the broader scientific community's quest to unravel the mysteries of the universe.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Localization of infrasonic sources via Bayesian back projection

SUMMARY A Bayesian framework is investigated for event-specific localization of infrasonic sources using back projection ray tracing. Direction-of-arrival information from array-based detection analysis is used to initialize a back projection ray path originating from the detecting array location and quantifying propagation characteristics from hypothetical source locations. The Fisher statistic, computed from the array’s beam coherence, is mapped into uncertainty in the launch angles of the ray path. Auxiliary parameters previously introduced for solving the Transport equation to compute geometric spreading along ray paths are used to map uncertainty in the ray launch angles into spatial and temporal uncertainties in the ray path. An atmospheric ensemble approach is applied to account for atmospheric uncertainty, and the relation between uncertainties in the atmospheric state and confidence in estimated localization are evaluated using several ensembles with specified variances. The method is evaluated using a synthetic event in the western United States constructed via forward propagation simulations as well as a single-station, multi-arrival detection from a surface explosion in the western United States. Localization results using this event-specific approach are more accurate and exhibit improved precision than existing Bayesian localization methods that leverage generalized, pre-computed propagation statistics.

58 GEOSCIENCES↗
NASA NTRS1987

Whistler mode emissions in the Uranian radiation belts

Voyager 2 detected intense whistler mode emissions and fluxes of energetic electrons during the outbound pass through the region of auroral L shells. The observed energetic (E greater than 22 keV) electron distribution, a model warm (E less than 27.5 keV) electron distribution, and the cold plasma density profile deduced by Kurth et al. (1987) are used to calculate the ray path-integrated spatial amplification of whistlers which arrive at Voyager 2 from the magnetic equator. By matching the calculated amplification and the relative gains at different frequencies deduced from the observed whistler power spectrum, the pitch angle anisotropy parameters of the electron distributions are determined to within a fairly narrow range of values. The estimated bounce average pitch angle diffusion coefficient indicates that electrons are on strong diffusion over a wide range in energies. The electron precipitation energy flux is sufficient to produce the observed auroral light emissions.

Coroniti, F. V.↗
NASA NTRS2005

Analysis of Quantum Information Test-Bed by Parametric Down-Converted Photons Interference Measurement

Quantum optical experiments require all the components involved to be extremely stable relative to each other. The stability can be "measured" by using an interferometric experiment. A pair of coherent photons produced by parametric down-conversion could be chosen to be orthogonally polarized initially. By rotating the polarization of one of the wave packets, they can be recombined at a beam splitter such that interference will occur. Theoretically, the interference will create four terms in the wave function. Two terms with both photons going to the same detector, and two terms will have the photons each going to different detectors. However, the latter will cancel each other out, thus no photons will arrive at the two detectors simultaneously under ideal conditions. The stability Of the test-bed can then be inferred by the dependence of coincidence count on the rotation angle.

To, Wing H.↗
NASA NTRS2004

Mars Exploration Rover Cruise Orbit Determination

The Mars Exploration Rover project consisted of two missions (MER-A: spirit rover and MER-B: opportunity rover) that launched spacecraft on June 10, 2003, and July 8, 2003, respectively. The spacecraft arrived at Mars approximately seven months later on January 4, 2004, and January 24, 2004. These spacecraft needed to be precisely navigated to a Mars atmospheric entry flight path angle of -11.5 deg +/-0.12 deg (3(sigma)) for MER-A and +/-0.14 deg (3(sigma)) for MER-B in order to satisfy the landing site delivery requirements. The orbit determination task of the navigation team needed to accurately determine the trajectory of the spacecraft, predict the trajectory to Mars atmospheric entry, and account for all possible errors sources so that the each spacecraft could be correctly targeted using five trajectory corrections along the way. This paper describes the orbit determination analysis which allowed MER-A to be targeted using only four trajectory correction maneuvers to an entry flight path angle of -11.49 deg +/-O.010 deg (3(sigma)) and MER-B to be targeted using only three trajectory correction maneuvers to an entry flight path angle of -11.47 +/-0.021 deg(3(sigma)).

navigation↗
NASA NTRS1991

Optical Receiver Based On Luminescent Light Trapping

Experiment demonstrates feasibility of optical-communication receiver based on luminescent light trapping. Light-gathering element plate of transparent material impregnated with laser dye. Light from distant laser transmitter falls on plate and absorbed by dye molecules, which become excited and reradiate. Reradiated light confined within plate by total internal reflection as it propagates toward edge of plate. Light arriving at edge escapes from plate and detected by small, high-speed, high-gain photomultiplier tubes or other photosensitive devices. Simple, inexpensive, and accepts light from almost any angle. Receiver of this configuration supports reception of data at rate of 13 MHz and higher.

Perry, Joseph W.↗