Search NASA⌕ Search

SEARCH · Search NASA

Results for “Axial Force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Analytical and experimental investigations of human spine flexure.

The authors report on experiments to measure the resistance of fresh human spines to flexion in the upper lumbar and lower thoracic regions and evaluate results by using a combination of strength of materials theory and effects of shear and comparing with data reported by other authors. The test results indicate that the thoraco-lumbar spine behaves approximately as a linear elastic beam, without relaxation effects. The authors formulate a simple continuum dynamic model of the spine simulating aircraft ejection and solve the resulting boundary value problem to illustrate the importance of the flexural mode. A constant cross-section, the selected model is a sinusoidally curved elastic beam with an end mass subjected to a Heaviside axial acceleration at the other end. The paper presents transient response results for the spinal model axial and bending displacements and axial force.-

Moffatt, C. A.↗
NASA NTRS1973

Design, fabrication, testing and delivery of a prototype self-locking actuator

The design, fabrication, and testing of a prototype self-locking actuator capable of producing an axial force of 44.5 kN are reported. The actuator passed the initial proof test successfully, however, when the no-load rate test was attempted, the actuator would not extend from the fully contracted position.

Dever, J. E.↗
NASA NTRS1973

Effect of nozzle lateral spacing, engine interfairing shape, and angle of attack on the performance of a twin-jet afterbody model with cone plug nozzles

Twin-jet afterbody models were investigated by using two balances to measure separately the thrust minus total axial force and the afterbody drag at Mach numbers from 0 to 1.3. Angle of attack was varied from minus 2 deg to 8.5 deg. Translating shroud cone plug nozzles were tested at dry-power and maximum-afterburning-power settings with a high-pressure air system used to provide jet total-pressure ratios up to 9.0. Two nozzle lateral spacings were studied by using afterbodies with several interfairing shapes. The close- and wide-spaced afterbodies had identical cross-sectional area distributions when similar interfairings were installed on each. The results show that the highest overall performance was obtained with the close-spaced afterbody and basic interfairings. Increasing angle of attack decreased performance for all configurations and conditions investigated.

Berrier, B. L.↗
NASA NTRS1973

Performance comparison of a lobed-daisy mixer nozzle with a convergent nozzle at subsonic speeds

An investigation to determine the performance, in terms of thrust minus nozzle axial force, of a lobed-daisy mixer nozzle has been conducted in a 16-foot transonic tunnel at static conditions and at Mach numbers from 0.40 to 0.90 at angles of attack from 4 minus to 8. Jet-total-pressure ratio was varied from about 1.2 to 2.0. The performance of a reference convergent nozzle with a similar nozzle throat area and length was used as a base line to evaluate the performance of the lobed-daisy mixer nozzle. The results of this investigation indicate that with no external airflow (Mach number M of 0), and at values of jet-total-pressure ratio between 1.2 and 2.0, the static thrust exerted by the lobed-daisy mixer nozzle is less than that of the convergent nozzle by about 10 percent of ideal gross thrust. About 3.4 percent of the thrust loss was attributed to an unintentional internal area expansion in the fan passage.

Maiden, D. L.↗
NASA NTRS1973

Effect of gaseous and solid simulated jet plumes on a 040A space shuttle launch configuration at Mach numbers from 1.6 to 2.2

An experimental investigation was conducted in a 9- by 7-foot supersonic wind tunnel to determine the effect of plume-induced flow separation and aspiration effects due to operation of both the orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the space shuttle vehicle. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold gas jet supplied by an auxiliary 200 atmosphere air supply system, and by solid body plume simulators. Comparisons of the aerodynamic effects produced by these two simulation procedures are presented. The data indicate that the parameters most significantly affected by the jet plumes are the pitching moment, the elevon control effectiveness, the axial force, and the orbiter wing loads.

Lanfranco, M. J.↗
NASA NTRS1974

Wind Tunnel Test Results of Fairings on A.004 Scale Model Rockwell Space Shuttle Integrated Vehicle Aerodynamic Characteristics at Mach Numbers from 0.6 to 4.96 (IA62F)

Experimental aerodynamic investigations were conducted on a .004 scale model (34-OTS) orbiter, external tank, and solid rocket booster combined as an integrated vehicle in the NASA/MSFC 14 x 14 inch trisonic wind tunnel. The primary test objective was to determine the effect of a full length orbiter/external tank fairing on axial force. Secondary objectives were to define the static stability characteristics of the mated vehicle configuration with fairings over a Mach number range of 0.6 thru 4.96. Six component aerodynamic force and moment data were recorded over an angle of attack range from -10 deg to 10 deg at 0 deg sideslip angle and from -10 deg to 10 deg sideslip range at 0 deg and 5 deg angle of attack. Plotted and tabular results are presented herein.

Allen, E. C.↗
NASA NTRS1974

Effect of gaseous and solid simulated jet plumes on an 040A space shuttle launch configuration at m=1.6 to 2.2

The effect of plume-induced flow separation and aspiration effects due to operation of both orbiter and the solid rocket motors on a 0.019-scale model of the launch configuration of the Space Shuttle Vehicle is determined. Longitudinal and lateral-directional stability data were obtained at Mach numbers of 1.6, 2.0, and 2.2 with and without the engines operating. The plumes exiting from the engines were simulated by a cold-gas jet supplied by an auxiliary 200-atm air supply system and solid-body plume simulators. The aerodynamic effects produced by these two simulation procedures are compared. The parameters most significantly affected by the jet plumes are pitching moment, elevon control effectiveness, axial force, and orbiter wing loads. The solid rocket motor (SRM) plumes have the largest effect on the aerodynamic characteristics. The effect of the orbiter plumes in combination with the SRM plumes is also significant. Variations in the nozzle design parameters and configuration changes can reduce the jet plume-induced aerodynamic effects.

Dods, J. B., Jr.↗
NASA NTRS1975

Results from investigations in the NASA/MSFC TWT on a .004 scale model space shuttle launch vehicle (model 13P-OTS) to determine gas supply strut effects on model pressure environment (IA53)

The Rockwell Space Shuttle Launch Vehicle components were tested in a Trisonic Wind Tunnel. Pressure measurements were made on the aft portion, in the base regions, and on the wing surfaces. Axial force determination were made from the pressure data. Data were recorded with the model at zero degrees angle of attack and sideslip through a Mach number from 0.9 to 3.0. The only configuration changes investigated were strut mounting techniques and gas line fairing location between the external tank and the orbiter.

Garton, W. P.↗
NASA NTRS1975

Integration of aft-fuselage-mounted flow through engine nacelles on an advanced transport configuration at Mach numbers from 0.6 to 1.0

An approximately 1/30th-scale model of a CTOL aircraft designed for efficient cruise between Mach 0.9 and 0.98 was tested in the Lewis Research Center's 8- by 6-Foot Supersonic Wind Tunnel. Aft-fuselage axial force and pressure were measured for a series of locally area-ruled engine installations. Two flow-through nacelles with different exit diameters which simulated inlet mass flow ratios of 0.46 and 0.6 (based on maximum nacelle cross-sectional) area were investigated. Both an NACA-1 cowl and a blunter supercritical cowl were tested with these nacelles. Variations in the amount of local area ruling were investigated and an aft fuselage without nacelles was tested for reference. Results observed with flow-through nacelles indicate that efficient cruise may be obtained on this type of aircraft with aft-fuselage-mounted engine nacelles.

Blaha, B. J.↗
NASA NTRS1976

Optimization of continuous one-dimensional structures under steady harmonic excitation

The paper examines some questions relating to the optimal design of continuous one-dimensional structures driven by harmonically oscillating loads. Optimal-control methods are applied to a cantilever bar driven sinusoidally by an axial force at its tip to illustrate the minimum-weight design of one-dimensional structures under dynamic excitation. Realistic constraints are imposed during the optimizations, including a maximum allowable stress amplitude at any point along the bar and a minimum cross-sectional area. It is shown that in the absence of damping, the design space may contain many disjoint feasible regions, and multiple optima can exist. Detailed solutions are obtained for continuous bars with an excitation frequency less than, and then greater than, the fundamental free-vibration frequency. It is found that above a certain excitation frequency, two or more arcs with different constraints characterize the optimal designs. It is concluded that when more than two different constrained arcs characterize the optimal solution, the continuum approach may be impractical, and finite-element approximations may offer the only alternative.

Johnson, E. H.↗
NASA NTRS1976

Transonic wind-tunnel tests of a lifting parachute model

Wind-tunnel tests have been made in the Langley transonic dynamics tunnel on a 0.25-scale model of Sandia Laboratories' 3.96-meter (13-foot), slanted ribbon design, lifting parachute. The lifting parachute is the first stage of a proposed two-stage payload delivery system. The lifting parachute model was attached to a forebody representing the payload. The forebody was designed and installed in the test section in a manner which allowed rotational freedom about the pitch and yaw axes. Values of parachute axial force coefficient, rolling moment coefficient, and payload trim angles in pitch and yaw are presented through the transonic speed range. Data are presented for the parachute in both the reefed and full open conditions. Time history records of lifting parachute deployment and disreefing tests are included.

Foughner, J. T., Jr.↗
NASA NTRS1977

Validation of a Flexible Aircraft TakeOff and Landing Analysis /FATOLA/ computer program using flight landing data

A multiple-degree-of-freedom takeoff and landing analysis, Flexible Aircraft TakeOff and Landing Analysis computer program (FATOLA), was used to predict the landing behavior of a rigid-body X-24B reentry research vehicle and of a flexible-body modified-delta-wing supersonic YF-12 research aircraft. The analytical predictions were compared with flight test data for both research vehicles. Predicted time histories of vehicle motion and attitude, landing-gear strut stroke, and axial force transmitted from the landing gear to the airframe during the landing impact and rollout compared well with the actual time histories. Based on the comparisons presented, the versatility and validity of the FATOLA program for predicting landing dynamics of aircraft has been demonstrated.

Carden, H. D.↗
NASA NTRS1978

Wind-tunnel investigation at Mach numbers from 1.90 to 2.86 of a canard-controlled missile with ram-air-jet spoiler roll control

The efficacy of using a ram-air-jet spoiler roll control device on a typical canard-controlled missile configuration was investigated. For roll control comparisons, conventional aileron controls on the tail fins were also tested. The results indicate that the roll control of the ram-air-jet spoiler tail fins at the highest free-stream Mach number compared favorably with that of the conventional 11-70 area-ratio tail fin ailerons, each deflected 10 deg. The roll control of the tail fin ailerons decreased while that of the ram-air-jet spoiler increased with free-stream Mach number. The addition of the ram-air-jet spoiler tail fins or flow-through tip chord nacelles on the tail fins resulted in only small changes in basic missile longitudinal stability. The axial force coefficient of the operating ram-air-jet spoiler is significantly larger than that of conventional ailerons and results primarily from the total pressure behind a normal shock in front of the nacelle inlets.

Blair, A. B., Jr.↗
NASA NTRS1977

Hydrodynamic effects in a misaligned radial face seal

Hydrodynamic effects in a flat seal having an angular misalignment are analyzed, taking into account the radial variation in seal clearance. An analytical solution for axial force, restoring moment, and transverse moment is presented that covers the whole range from zero to full angular misalignment. Both low pressure seals with cavitating flow and high pressure seals with full fluid film are considered. Strong coupling is demonstrated between angular misalignment and transverse moment which leads the misalignment vector by 90 degrees. This transverse moment, which is entirely due to hydrodynamic effects, is a significant factor in the seal operating mechanism.

Etsion, I.↗
NASA NTRS1979

Stability and control characteristics of a monoplanar elliptic missile model at Mach numbers from 1.60 to 2.86

An investigation was conducted of a monoplanar maneuverable missile concept having a nose forebody with a circular cross section and a centerbody and afterbody with elliptical cross sections. The tests involved several component changes and were conducted in the low Mach number test section of the Langley Unitary Plan wind tunnel at Mach numbers of 1.60, 2.16, and 2.86, at angles of attack ranging from -4 degs to 28 degs and at sideslip angles ranging from -4 degs to 8 degs. The most significant result was that at the highest Mach number (2.86), the configuration with the infrared nose produced nearly twice the axial force as the same configuration with the radar nose. The cranked wing had a destabilizing effect on the longitudinal stability and had no effect on the lateral-directional stability. The nose strakes had no effect longitudinally and were detrimental to the lateral-directional stability.

Sawyer, W. C.↗
NASA NTRS1978

An experimental wind-tunnel investigation of a ram-air-spoiler roll-control device on a forward-control missile at supersonic speeds

A parametric experimental wind-tunnel investigation was made at supersonic Mach numbers to provide design data on a ram-air-spoiler roll-control device that is to be used on forward-control cruciform missile configurations. The results indicate that the ram-air-spoiler tail fin is an effective roll-control device and that roll control is generally constant with vehicle attitude and Mach number unless direct canard and/or forebody shock impingement occurs. The addition of the ram-air-spoiler tail fins resulted in only small changes in aerodynamic-center location. For the ram-air-spoiler configuration tested, there are large axial force coefficient effects associated with the increased fin thickness and ram-air momentum loss.

Blair, A. B., Jr.↗
NASA NTRS1978

Hydrodynamic effects in a misaligned radial face seal

Hydrodynamic effects in a flat seal having an angular misalignment are analyzed, taking into account the radial variation in seal clearance. An analytical solution for axial force, restoring moment, and transverse moment is presented that covers the whole range from zero to full angular misalignment. Both low pressure seals with cavitating flow and high pressure seals with full fluid film are considered. Strong coupling is demonstrated between angular misalignment and transverse moment which leads the misalignment vector by 90 degrees. This transverse moment, which is entirely due to hydrodynamic effects, may be a significant factor in seal operating mechanism.

Etsion, I.↗
NASA NTRS1981

The effect of lamination-induced stresses on fatigue damage development at internal flaws

The effects of stresses induced by the lamination of off-axis plies to O-deg lamina on the development of damage during the fatigue loading of the O-deg plies are discussed. The transverse normal stresses in the plane of the laminae and the laminate created by the laminating constraints when an axial force is applied to the laminate are calculated in terms of a differential Poisson ratio between the ply in question in the unconstrained and constrained states, and significant differences in the constraint environments of an unnotched specimen joined to plies of 45 and 90 deg inclination are noted which correspond to an increase in longitudinal splitting in the 90 deg case and a marked decrease in longitudinal splitting in the 45 deg case. If a notch is present, shear and crack-opening damage is found to be very effectively suppressed in 45-deg laminates, and less so in the 90-deg case. It is pointed out that whereas the 45-deg laminate represents the least damage situation, it does not have the greatest notched strength. It is concluded that an understanding and prediction of damage development in laminates requires knowledge of the stress fields caused by the lamination constraints.

Reifsnider, K. L.↗