Search NASA⌕ Search

SEARCH · Search NASA

Results for “BACKGROUND NOISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Signal-to-noise ratios of multiplexing spectrometers in high backgrounds

Signal-to-noise ratios and the amount of multiplexing gain achieved with a Michelson spectrometer during detector and background noise are studied. Noise caused by the warm background is found in 10 and 20-micron atmospheric windows in high resolution Fourier spectroscopy. An equation is derived for the signal-to-noise ratio based on the number of channels, total time to obtain the complete spectrum, the signal power in one spectral element, and the detector noise equivalent power in the presence of negligible background. Similar expressions are derived for backgrounds yielding a noise equivalent power to a spectral element, and backgrounds having flat spectra in the frequency range under investigation.

Knacke, R. F.↗

Effect of detector dead time on the performance of optical direct-detection communication links

Avalanche photodiodes (APDs) operating in the Geiger mode can provide a significantly improved single-photon detection sensitivity over conventional photodiodes. However, the quenching circuit required to remove the excess charge carriers after each photon event can introduce an undesirable dead time into the detection process. The effect of this detector dead time on the performance of a binary pulse-position-modulated (PPM) channel is studied by analyzing the error probability. It is shown that, when background noise is negligible, the performance of the detector with dead time is similar to that of a quantum-limited receiver. For systems with increasing background intensities, the error rate of the receiver starts to degrade rapidly with increasing dead time. The power penalty due to detector dead time is also evaluated and shown to depend critically on badkground intensity as well as dead time. Given the expected background strength in an optical channel, therefore, a constraint must be placed on the bandwidth of the receiver to limit the amount of power penalty due to detector dead time.

Chen, C.-C.↗

High-directivity acoustic antenna

Acoustic antenna with unique electronic steering control is used to identify and define aerodynamic noise sources in free field, particularly in wind tunnel which is quite reverberant. Provision is made for high directivity as well as improved discrimination against unwanted background noise such as reverberation or echoes.

El-Sum, H. M. A.↗

Test results and in-orbit operation of the Infrared Astronomical Satellite circumvention circuit

The IRAS circumvention circuit (CC) eliminates the unwanted charged-particle pulses from the IR signal. The operation of the CC along with preflight and in-orbit testing is described. Ground testing of the brassboard circuit using a simulated preamplifier output showed that the CC would perform the circumvention function as designed. When all flight detectors and preamplifiers became available, the CC was tested using a gamma source to simulate charged-particle sources; with the low energy deposited in the detectors (20 keV average) the noise was reduced by up to 5 times with the CC turned on. In-orbit results show that the CC decreases the unwanted charged-particle background noise by up to two orders of magnitude. The difference in the results with the CC on and off is so great that the science team has recommended that no data be taken with the CC off.

Long, E. C.↗

Measurements of V/STOL aircraft noise mechanisms using pressure cross-correlation techniques in a reverberant wind tunnel

A 3.8 cm. model jet was operated in a wind tunnel with cross-flow in order to determine the effect on jet noise radiated characteristics. A method was developed for the determination of noise radiating characteristics of sources within reverberant wind tunnels; cross-correlation measurements were used. The averaging time in the cross-correlation is determined by the amount of background noise within the wind tunnel. It was found that cross-flow increases the radiated noise by 10 db. There was some indication of downstream radiation exceeding the sideline radiation.

Meecham, W. C.↗

Evaluation of the Langley 4- by 7-meter tunnel for propeller noise measurements

An experimental and theoretical evaluation of the Langley 4- by 7- Meter Tunnel was conducted to determine its suitability for obtaining propeller noise data. The tunnel circuit and open test section are described. An experimental evaluation is performed using microphones placed in and on the tunnel floor. The reflection characteristics and background noise are determined. The predicted source (propeller) near-field/far-field boundary is given using a first-principles method. The effect of the tunnel-floor boundry layer on the noise from the propeller is also predicted. A propeller test stand used for part of his evaluation is also described. The measured propeller performance characteristics are compared with those obtained at a larger scale, and the effect of the test-section configuration on the propeller performance is examined. Finally, propeller noise measurements were obtained on an eight-bladed SR-2 propeller operating at angles of attack -8 deg, 0 deg, and 4.6 deg to give an indication of attainable signal-to-noise ratios.

Block, P. J. W.↗

Spontaneous generation of athermal phonon bursts within bulk silicon causing excess noise, low energy background events, and quasiparticle poisoning in superconducting sensors

Solid state phonon detectors used in the search for dark matter and coherent neutrino nucleus interactions (CE $v$ NS) require excellent energy resolution (eV-scale or below) and low backgrounds. An unknown source of phonon bursts, the low energy excess (LEE), dominates other above-threshold backgrounds and generates excess shot noise from subthreshold bursts. Here, in this paper, we measure these phonon bursts for 12 days after cooldown in two nearly identical 1 cm 2 silicon detectors that differ only in the thickness of their substrate (1 vs 4 mm thick). We find that both the channel-correlated shot noise and near-threshold shared LEE relax with time since cooldown. Additionally, both the correlated shot noise and LEE rates scale linearly with substrate thickness. When combined with previous measurements of other silicon phonon detectors with different substrate geometries and mechanical support strategies, these measurements strongly suggest that the dominant source of both above and below threshold LEE is the bulk substrate. By monitoring the relation between bias power and excess phonon shot noise, we estimate that the energy scale for subthreshold noise events is 0.68 ± 0.38 meV. In our final dataset, we report a world-leading energy resolution of 258.5 ± 0.4 meV in the 1 mm thick detector. Simple calculations suggest that these silicon substrate phonon bursts are likely a significant source of quasiparticle poisoning in superconducting qubits operated in well shielded and vibration free environments.

Chang, C. L. [Argonne National Laboratory 1 , 9700↗

Detectability of auditory signals presented without defined observation intervals

Ability to detect tones in noise was measured without defined observation intervals. Latency density functions were estimated for the first response following a signal and, separately, for the first response following randomly distributed instances of background noise. Detection performance was measured by the maximum separation between the cumulative latency density functions for signal-plus-noise and for noise alone. Values of the index of detectability, estimated by this procedure, were approximately those obtained with a 2-dB weaker signal and defined observation intervals. Simulation of defined- and non-defined-interval tasks with an energy detector showed that this device performs very similarly to the human listener in both cases.

Watson, C. S.↗

Noise measurements from an ejector suppressor nozzle in the NASA Lewis 9- by 15-foot low speed wind tunnel

Acoustic results are presented of a cooperative nozzle test program between NASA and Pratt and Whitney, conducted in the NASA-Lewis 9 x 15 ft Anechoic Wind Tunnel. The nozzle tested was the P and W Hypermix Nozzle concept, a 2-D lobed mixer nozzle followed by a short ejector section made to promote rapid mixing of the induced ejector nozzle flow. Acoustic and aerodynamic measurements were made to determine the amount of ejector pumping, degree of mixing, and noise reduction achieved. A series of tests were run to verify the acoustic quality of this tunnel. The results indicated that the tunnel test section is reasonably anechoic but that background noise can limit the amount of suppression observed from suppressor nozzles. Also, a possible internal noise was observed in the air supply system. The P and W ejector suppressor nozzle demonstrated the potential of this concept to significantly reduce jet noise. Significant reduction in low frequency noise was achieved by increasing the peak jet noise frequency. This was accomplished by breaking the jet into segments with smaller dimensions than those of the baseline nozzle. Variations in ejector parameters had little effect on the noise for the geometries and the range of temperatures and pressure ratios tested.

Krejsa, Eugene A.↗

Coded aperture imaging - Predicted performance of uniformly redundant arrays

It is noted that uniformly redundant arrays (URAs) have autocorrelation functions with perfectly flat sidelobes. A generalized signal-to-noise equation has been developed to predict URA performance. The signal-to-noise value is formulated as a function of aperture transmission or density, the ratio of the intensity of a resolution element to the integrated source intensity, and the ratio of detector background noise to the integrated intensity. It is shown that the only two-dimensional URAs known have a transmission of one half. This is not a great limitation because a nonoptimum transmission of one half never reduces the signal-to-noise ratio more than 30%. The reconstructed URA image contains practically uniform noise, regardless of the object structure. URA's improvement over the single-pinhole camera is much larger for high-intensity points than for low-intensity points.

Fenimore, E. E.↗

Toward Relating Open- and Closed-Test Section Microphone Phased Array Aeroacoustic Measurements

Aeroacoustic measurements utilizing microphone phased arrays are becoming more commonplace in large-scale wind tunnels. However, for such costly tests it is difficult to assess the influence of a given facility's configuration on the acquired data. One such opportunity has recently arisen in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel, where the High-Lift configuration of the Common Research Model was tested in both open-jet and closed wall configurations. Acoustic data were acquired on the same model with the same specific hardware at the same Mach number; and for similar model angles of attack, array apertures, and array angles relative to the model location. Initial deconvolution comparisons using DAMAS appear poor. The closed test section results show contamination likely due to background noise and reflections. The open-jet results show severe blurring due to the decorrelation of acoustic waves passing through a turbulent free shear layer. However, accounting for image sources in the DAMAS grid reduces visual artifacts in the closed test section results, and a preliminary coherence correction technique mitigates the blurring in the open-jet results. Qualitatively, both tests identify similar source behavior. Quantitatively, summed spectra of the slat noise agree in some frequency bands but differ in others. Proposals that may mitigate the difference are given for each configuration, such as correcting for the array protective cover and applying background subtraction in the closed wall configuration, and further developing the coherence loss correction for deconvolution methods in the open-jet setup.

microphone array↗

A Psychoacoustic Test on the Effect of Masking on Annoyance to Urban Air Mobility Vehicle Noise

Urban Air Mobility (UAM) vehicles have a large range of designs and configurations that lead to new noise characteristics and potentially different perceptual responses when compared to traditional aircraft. In addition, UAM vehicles are expected to operate around and within densely populated regions where the presence of ambient background noise is often present. Strategically, this can be leveraged to inform vehicle design and operations to partially or completely mask UAM noise, allowing for mitigation of negative responses and an increased number of allowed operations. A psychoacoustic test was conducted to investigate how masking effects can influence the annoyance response to a low frequency harmonic tone complex (80-320 Hz). To do this, five test subjects compared their annoyance response to the low frequency tonal noise with a higher frequency broadband noise (10dB down bandwidth between 300-2000 Hz), with and without a masking noise present. Detection thresholds were also measured for both sounds to help fit a model to the data. Although the effect of masking on annoyance is complex, results indicate that for some individuals, masking leads to a lower annoyance than the sound level alone would predict.

Matthew Boucher↗

Comparison of options for reduction of noise in the test section of the NASA Langley 4x7m wind tunnel, including reduction of nozzle area

The acoustically significant features of the NASA 4X7m wind tunnel and the Dutch-German DNW low speed tunnel are compared to illustrate the reasons for large differences in background noise in the open jet test sections of the two tunnels. Also introduced is the concept of reducing test section noise levels through fan and turning vane source reductions which can be brought about by reducing the nozzle cross sectional area, and thus the circuit mass flow for a particular exit velocity. The costs and benefits of treating sources, paths, and changing nozzle geometry are reviewed.

Hayden, R. E.↗

Statistical Validation of Multiple Related Data Sets—Case Study Using Interstellar Boundary Explorer Satellite Data

Abstract Space scientists often face the question of whether data collected by different instruments are measurements of the same source population. This paper proposes a statistical validation method for evaluating the agreement between such related data sets. It offers a detailed case study focused on validating a new data set from the Interstellar Boundary Explorer (IBEX) mission, which serves as a practical how-to guide for similar analyses. Since 2008, the IBEX satellite has been gathering data on heliospheric energetic neutral atoms (ENAs) while being exposed to various sources of background noise, such as cosmic rays and solar energetic particles. The IBEX mission initially released only a qualified triple-coincidence (qABC) data product, which was designed to provide observations of ENAs free of background contamination. Further measurements revealed that the qABC data were in fact susceptible to contamination, having relatively low ENA counts and high background rates. To mitigate this issue, the mission team recently considered releasing a certain qualified double-coincidence (qBC) data product, which has roughly twice the detection rate of the qABC data product. This paper presents a simulation-based validation of the new qBC data product against the already-released qABC data product. The results show that the qBCs can plausibly be said to be measuring the same source population as the qABCs up to an average absolute deviation of 3.6%. Visual diagnostics provide additional confirmation of source rate coherence across data products. The framework introduced here is general and can be applied to other validation problems both within and outside the field of space physics.

79 ASTRONOMY AND ASTROPHYSICS↗

Preliminary measurement of the airframe noise from an F-106B delta wing aircraft at low flyover speeds

To establish a realistic lower limit for the noise level of advanced supersonic transport aircraft will require knowledge concerning the amount of noise generated by the airframe itself as it moves through the air. The airframe noise level of an F-106B aircraft was determined and was compared to that predicted from an existing empirical relationship. The data were obtained from flyover and static tests conducted to determine the background noise level of the F-106B aircraft. Preliminary results indicate that the spectrum associated with airframe noise was broadband and peaked at a frequency of about 570 hertz. An existing empirical method successfully predicted the frequency where the spectrum peaked. However, the predicted OASPL value of 105 db was considerably greater than the measures value of 83 db.

Burley, R. R.↗

Appendix: Limits on the use of heterodyning and amplification in optical interferometry

The development of optical fibers, lasers, and mixers at optical frequencies has offered the hope that active methods can contribute to optical interferometry. Heterodyning, in particular, looks attractive, even though bandwidths are narrower than one would like at present; one might expect this limitation to lessen as technology develops. That expectation, unfortunately, is not likely to benefit interferometry at optical wavelengths because of the intervention of quantum mechanics and the second law of thermodynamics, as Burke (1985a) pointed out. So much 'second quantization' noise is generated that only at infrared frequencies, somewhere in the 10-100 micron range, can one look forward to heterodyning in any realistic sense. The reason is easily understood. Every amplifier, in the quantum limit, works by stimulated emission, even though this basic truth is not obvious at radio frequencies. This means that there must be spontaneous emission occurring within every amplifier, and Strandberg (1957) showed that this implied a limiting noise temperature, T sub N = h nu/k, for any amplifier. Burke (1969) used this result to demonstrate that, if it were not for this quantum noise, the VLBI method would allow one to tell which slit a photon went through before forming an interference pattern, thus violating basic tenants of quantum mechanics. In essence, the second quantization condition Delta N Delta phi greater than or = 1 saves one from paradox. One can state the conclusion simply: any amplifier produces approximately one photon per Hertz of bandwidth. In optical interferometry, one will certainly want bandwidth in the 10(exp 12) to 10(exp 14) Hz range, and that implies an intolerable cacophony of noise photons. Only at infrared frequencies can one tolerate the quantum noise, where the natural noise background may be high and the mixers are not as efficient as one would hope for. The crossover at present is about 10 or 20 microns, but the boundary will shift to longer wavelengths as noise performance improves. One might guess that ultimately a wavelength of about 100 microns will mark the limit of useful amplification and heterodyning in astronomical aperture synthesis interferometry.

Burke, Bernard F.↗

Statistical optical link budget analysis

In this paper, we describe work on extending statistical analysis methods to optical communications links, with a primary focus on intensity modulated, direct detected photon-counting channel utilizing pulse-position-modulation (PPM). We performed analysis on the relationship between bit error rate (BER) requirement, statistical characteristics of the received signal power and noise power, and the coded performance curves. We presented link analysis results with preliminary uncertainty quantifications of signal power and noise power. We used the Consultative Committee for Space Data Systems (CCSDS) Serially Concatenated convolutionally coded Pulse Position Modulation (SCPPM) prototype software [1] to obtain coded performance curves under different operating conditions with varying signal power, background noise power, code rates,and PPM modulation orders. Comparison with traditional, deterministic analysis shows that extra margin needs to be reserved to compensate for the performance losses caused by uncertainties of the link parameters.

Cheung, Kar-Ming↗

Aspects of large-scale, subsonic, wind-tunnel design for propulsion noise research

The case for full-scale acoustic testing of propulsion systems at flight conditions and the use of wind tunnels for this work are discussed. The problems associated with measuring noise in wind tunnels are discussed, and wind-tunnel design requirements to provide a useful facility for noise research are established. Full-scale subsonic wind-tunnel designs that meet the requirements are described, and it is shown that state-of-art acoustics technology must be used in the drive-fan design to minimize background noise. If this is successfully done, acoustic treatment in the drive system area may be avoided.

Hickey, D. H.↗