Aero-astrodynamics Research Review No. 3, January 1 - June 30, 1965
Aerodynamics, spacecraft instrumentation, guidance and control, aerothermodynamics, base heating, and structural dynamics
BASE HEATING↗
SEARCH · Search NASA
Results for “Base heating”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A Warm Garage for a Lunar Rover
Approach: One approach to heating a rover during the lunar night is the so-called thermal wadis concept [1]. This involves heating the regolith with solar concentrators and placing the rover on the heated surface for the night. Since the regolith is heated by a relatively weak heat flux, a high thermal conductivity is required for heating a sufficiently large mass of regolith. However, lunar regolith has a low thermal conductivity. Therefore, the concept involves increasing the conductivity by sintering the regolith, which requires a significant energy input and complex procedures. Here we propose an alternative approach where the low thermal conductivity of regolith is an advantage. Specifically, we propose to use a highly exothermic combustible mixture for heat generation. The mixture pellets are placed in the surface layer of regolith and ignited. The combustion forms condensed products and releases heat, which then slowly spreads to the surrounding regolith. Heat can also be transferred, for example, by heat pipes, into radiant heating surfaces installed on the ground. A greenhouse that transmits sunlight during the day and decreases the radiative heat losses during the night can also be installed. Selection of the Heat-generating Mixture: The reactive mixture should have a high specific energy and generate only condensed products since gases could disturb the regolith layer, carry enthalpy out of the system, and lead to an explosion. There are mixtures, (sometimes called pyrolants) that possess very high specific energies. One example is magnesium-Teflon-Viton mixtures used in flares. However, they produce gases and may cause explosions. Other mixtures that include magnesium cannot be used either because of the high vapor pressure of Mg at temperatures well below the combustion temperature. Recently, mixtures that involve lithium peroxide (Li2O2) have been proposedfor using in space power systems [2]. However, they produce lithium oxide (Li2O), which boils at 2800 K at 1 atm and hence at a lower temperature in vacuum. Fortunately, there exist many mixtures that release a lot of heat and form only condensed products during the combustion. Many such mixtures have been used for self-propagating high-temperature synthesis (SHS) of various materials [3, 4]. For the application discussed here, t itanium/boron (1:2 mole ratio) mixture appears to be particularly promising. The specific energy is 4.0 MJ/kg (1.1 kWh/kg), the adiabatic flame temperature is about 3200 K, and the reaction forms solid titanium diboride (TiB2, melting point: 3500 K). The mixture can be ignited easily with a heated tungsten wire, and it has been used widely as a booster to ignite the main mixture in the SHS process.Estimates: Assuming that specific heat of regolith is 500 J/(kg∙K) [5] and all generated heat is transferred to regolith, 12.5 kg of the Ti/B mixture would increase the temperature of 1000 kg of regolith by 100 K. To evaluate the rate of heat transfer in the regolith, a spherical model was analyzed where the heat released by a 12.5 kg Ti/B core propagates by thermal conduction through a 1000 kg regolith shell with no heat loss from its outer surface. At a bulk density of 1500 kg/m3 [5], the radius of the shell was 54 cm, while the radius of the core was about 11 cm. The calculations were conducted using Thermal Desktop SINDA/FLUINT (Cullimore and Ring Technologies) software at two constant values of bulk thermal conductivityk of the regolith: 0.001 and 0.01 W/(m∙K). The results show that after 14.5 days the core lost 31% of the released heat at the lower k and 77% at the higher k. At a distance of 20 cm from the core surface, the temperature of the regolith increased by only 1 K at the lower k and by 132 K at the higher k. In reality, the regolith near the heat source will be melted, so its thermal conductivity will increase significantly. Nevertheless, the conducted estimates indicate that combustion-based heat generators, placed directly in the regolith, could provide heat during a rather long period such as the lunar night.Conclusion: Heat generators based on gasless combustion of highly energetic reactive mixtures could be installed directly in the surface layer of lunar regolith. Because of the low thermal conductivity of the regolith, such generators would keep thermal energy for days and gradually supply heat to a rover/lander.Acknowledgment: The material presented in this work is based upon the work supported by National Aeronautics and Space Administration (NASA) under Grant #80NSSC20K0293.References: [1] Balasubramaniam R. et al. (2011) J. Thermophys. Heat Trans., 25,130−139. [2] Blair R.G. and Vasu S.S. (2022) Conf. Advanced Power Systems for Deep Space Exploration. [3] Varma A. et al. (1998) Adv. Chem. Eng., 24,79−226. [4] Levashov E.A. et al. (2017) Int. Mater. Rev., 62,203−239. [5] Wood-Robinson R. et al. (2019) J. Geophys. Res. Planets, 124, 1989−2011.
lunar↗
Base Flow and Heat Transfer Characteristics of a Four-Nozzle Clustered Rocket Engine: Effect of Nozzle Pressure Ratio
The base pressure and heating characteristics of a four-nozzle clustered rocket configuration is studied numerically with the aid of OVERFLOW Navier-Stokes code. A pressure ratio (chamber pressure to freestream static pressure) range of 990 to 5,920 and a freestream Mach number range of 2.5 to 3.5 are studied. The qualitative trends of decreasing base pressure with increasing pressure ratio and increasing base heat flux with increasing pressure ratio are correctly predicted. However, the predictions for base pressure and base heat flux show deviations from the wind tunnel data. The differences in absolute values between the computation and the data are attributed to factors such as perfect gas (thermally and calorically perfect) assumption, turbulence model inaccuracies in the simulation, and lack of grid adaptation.
Nallasamy, R.↗
Continuous carbon absorption studies
Absorption coefficient of carbon from rocket exhaust and large booster base heating
CARBON↗
The Saturn S-IV stage base thermal environment flight and scale model data comparison.
Base heating in Saturn S-IV stage from exhaust reversal, comparing flight and scale model data
BASE HEATING↗
Combining Satellite Microwave Radiometer and Radar Observations to Estimate Atmospheric Latent Heating Profiles
In this study, satellite passive microwave sensor observations from the TRMM Microwave Imager (TMI) are utilized to make estimates of latent + eddy sensible heating rates (Q1-QR) in regions of precipitation. The TMI heating algorithm (TRAIN) is calibrated, or "trained" using relatively accurate estimates of heating based upon spaceborne Precipitation Radar (PR) observations collocated with the TMI observations over a one-month period. The heating estimation technique is based upon a previously described Bayesian methodology, but with improvements in supporting cloud-resolving model simulations, an adjustment of precipitation echo tops to compensate for model biases, and a separate scaling of convective and stratiform heating components that leads to an approximate balance between estimated vertically-integrated condensation and surface precipitation. Estimates of Q1-QR from TMI compare favorably with the PR training estimates and show only modest sensitivity to the cloud-resolving model simulations of heating used to construct the training data. Moreover, the net condensation in the corresponding annual mean satellite latent heating profile is within a few percent of the annual mean surface precipitation rate over the tropical and subtropical oceans where the algorithm is applied. Comparisons of Q1 produced by combining TMI Q1-QR with independently derived estimates of QR show reasonable agreement with rawinsonde-based analyses of Q1 from two field campaigns, although the satellite estimates exhibit heating profile structure with sharper and more intense heating peaks than the rawinsonde estimates. 2
Grecu, Mircea↗
Space vehicle engine and heat shield environment review. Volume 1: Engineering analysis
Methods for predicting the base heating characteristics of a multiple rocket engine installation are discussed. The environmental data is applied to the design of adequate protection system for the engine components. The methods for predicting the base region thermal environment are categorized as: (1) scale model testing, (2) extrapolation of previous and related flight test results, and (3) semiempirical analytical techniques.
Mcanelly, W. B.↗
Thermoelectric Air/Soil Energy-Harvesting Device
A proposed thermoelectric device would exploit natural temperature differences between air and soil to harvest small amounts of electric energy. Because the air/soil temperature difference fluctuates between nighttime and daytime, it is almost never zero, and so there is almost always some energy available for harvesting. Unlike photovoltaic cells, the proposed device could operate in the absence of sunlight. Unlike a Stirling engine, which could be designed to extract energy from the air/soil temperature difference, the proposed device would contain no moving parts. The main attractive feature of the proposed device would be high reliability. In a typical application, this device would be used for low-power charging of a battery that would, in turn, supply high power at brief, infrequent intervals for operating an instrumentation package containing sensors and communication circuits. The device (see figure) would include a heat exchanger buried in soil and connected to a heat pipe extending up to a short distance above the ground surface. A thermoelectric microgenerator (TEMG) would be mounted on top of the heat pipe. The TEMG could be of an advanced type, now under development, that could maintain high (relative to prior thermoelectric generators) power densities at small temperature differentials. A heat exchanger exposed to the air would be mounted on top of the TEMG. It would not matter whether the air was warmer than the soil or the soil warmer than the air: as long as there was a nonzero temperature difference, heat would flow through the device and electricity would be generated. A study of factors that could affect the design and operation of the device has been performed. These factors include the thermal conductances of the soil, the components of the device, the contacts between the components of the device, and the interfaces between the heat exchangers and their environments. The study included experiments that were performed on a model of the device to demonstrate feasibility. Because a TEMG suitable for this device was not available, a brass dummy component having a known thermal conductance of 1.68 W/K was substituted for the TEMG in the models to enable measurement of heat flows. The model included a water-based heat pipe 30 in. (76.2 cm) long and 1 in. (2.54 cm) in diameter, wrapped with polyethylene insulation to reduce radial heat flow. Several different side heat exchangers were tested. On the basis of the measurements, it was predicted that if a prototype of the device were equipped with a TEMG, daily temperature fluctuations would cause its output power to fluctuate between 0 and about 0.1 mW, peaking to 0.35 mW during early afternoon.
Snyder, Jeffrey↗
Study Of Heating Of The Base Region Of A Rocket
Report describes theoretical study of heating in base region of proposed rocket called "NLS 1.5 stage reference vehicle." Study employed approach based on computational fluid dynamics (CFD). Involved numerical simulations of flow field in base region and in main exhaust plume of cluster of six engines with heat shields.
Ascoli, Edward P.↗
Microsphere Plutonium-238 Oxide Fuel to Revolutionize New Radioisotope Power Systems and Heat Sources for Planetary Exploration
Microsphere 238PuO2 fuels have potential to provide performance and safety enhancements for future radioisotope heat and power systems (RPS) as well as enable more flexible and compact RPS designs. Improvements in RPS specific power and more flexible geometries were recently investigated by JPL and PNNL as part of a study on cryobot devices for exploring Ocean Worlds. Missions to penetrate ice and explore oceans, such as on Europa, will require RPS with high specific power within the vehicle to provide both heat and power. Such missions will be mass-constrained, and the energy required to penetrate the ice is highly dependent on cryobot size. Therefore, compact RPS geometries are needed to maximize heat and power while minimizing 238Pu inventory. Microsphere-based heat sources are an attractive way to obtain flexible geometries and high volumetric power loadings because they can fill a region of any size and shape provided fuel temperatures are kept below a threshold and launch/re-entry safety are not compromised. The sol-gel technique to produce 238PuO2 microsphere particles for heat sources has the benefit of preventing dust generation, as opposed to the current 238PuO2 powder/pellet processing method, reducing hazards in the fuel fabrication line. Microspheres can also be individually coated to enhance thermal conductivity, and/or reduce the likelihood of 238PuO2 fuel dispersal in an accident. Although PNNL has produced 238PuO2 microspheres using the sol-gel method, the application of coatings and their integrity over time has yet to be investigated. Continued R&D could demonstrate the feasibility of advanced, microspherebased heat sources and provide baseline data for planning future missions requiring new RPS with different heat source configurations.
Fleurial, Jean-Pierre↗
Heat-transfer telemetry for models using thermocouple sensors.
Telemetry technique utilizing thermocouple sensors for base heating determinations on free flight blunt cone in shock tunnels, noting electrical noise reduction
Harrison, D. R.↗
Analysis of a membrane-based condesate recovery heat exchanger (CRX)
The development of a temperature and humidity control system that can remove heat and recover water vapor is key to the development of an Environmental Control and Life Support System (ECLSS). Large quantities of water vapor must be removed from air, and this operation has proven difficult in the absense of gravity. This paper presents the modeling results from a program to develop a novel membrane-based heat exchanger known as the condensate recovery heat exchanger (CRX). This device cools and dehumidifies humid air and simultaneously recovers water-vapor condensate. In this paper, the CRX is described and the results of an analysis of the heat- and mass-transfer characteristics of the device are given.
Newbold, D.D.↗
Features of Afterbody Radiative Heating for Jupiter Entry
In this extended abstract, a preliminary analysis of a trajectory-based heating and ablation study in the afterbody of a Jovian entry probe is presented. The radiative flux in the afterbody impinging on the backshell of the probe is investigated with and without the presence of ablation product gas. The heritage tangent-slab approximation for radiative heating is shown to underpredict the radiative heating by as much as 50% in the afterbody making the highfidelity, yet computationally expensive, ray-tracing approach necessary to accurately predict the radiative heating predictions. An investigation into the merits of employing the ray-tracing approach for the prediction of the divergence of radiative flux in the afterbody flow field will be presented in the final manuscript. Nonequilibrium effects in the afterbody region will be investigated in the final manuscript including the impact of electron-ion recombination rates. To bound the problem based on the best available knowledge, an uncertainty analysis will be performed. Sources of uncertainty are identified in the ablation modeling, radiation modeling, flowfield kinetics, and thermodynamic properties of select species.
Thermophysics↗
On Heatshield Shapes for Mars Entry Capsules
The 70deg sphere-cone - the standard geometry for all US Mars entry missions - is thoroughly examined via flow field simulations at a select few peak heating points along candidate flight trajectories. Emphasis is placed on turbulent heating based on the Baldwin- Lomax turbulence model. It is shown that increased leeward turbulent heating for a 70 sphere-cone flying at angle of attack is primarily due to the discontinuity in curvature between the spherical nose cap and the conical frustum - the attachment of the sonic line at this sphere-cone junction leads to a supersonic edge Mach number over the leeward acreage. In an attempt to mitigate this problem of elevated turbulent heating, alternate geometries, without any curvature discontinuities in the acreage, are developed. Two approaches, one based on nonlinear optimization with constraints, and one based on the use of non-uniform rational B-splines, are considered. All configurations examined remain axisymmetric. The aerothermal performance of alternate geometries is shown to be superior to that of the 70 sphere-cone.
Prabhu, DInesh K.↗
Heat-transfer telemetry from free-flight models in wind tunnels. II.
Telemetry technique utilizing thermocouple sensors for base heating determinations on free flight blunt cone in shock tunnels, noting electrical noise reduction
Harrison, D. R.↗
Light Microsopy Module, International Space Station Premier Automated Microscope
The Light Microscopy Module (LMM) was launched to the International Space Station (ISS) in 2009 and began science operations in 2010. It continues to support Physical and Biological scientific research on ISS. During 2015, if all goes as planned, five experiments will be completed: [1] Advanced Colloids Experiments with a manual sample base -3 (ACE-M-3), [2] the Advanced Colloids Experiment with a Heated Base -1 (ACE-H-1), [3] (ACE-H-2), [4] the Advanced Plant Experiment -03 (APEX-03), and [5] the Microchannel Diffusion Experiment (MDE). Preliminary results, along with an overview of present and future LMM capabilities will be presented; this includes details on the planned data imaging processing and storage system, along with the confocal upgrade to the core microscope. [1] New York University: Paul Chaikin, Andrew Hollingsworth, and Stefano Sacanna, [2] University of Pennsylvania: Arjun Yodh and Matthew Gratale, [3] a consortium of universities from the State of Kentucky working through the Experimental Program to Stimulate Competitive Research (EPSCoR): Stuart Williams, Gerold Willing, Hemali Rathnayake, et al., [4] from the University of Florida and CASIS: Anna-Lisa Paul and Rob Ferl, and [5] from the Methodist Hospital Research Institute from CASIS: Alessandro Grattoni and Giancarlo Canavese.
Microscopy↗
Space shuttle: Experimental investigations for base drag reduction on a 0.015 scale model MSFS proposed space shuttle booster at Mach numbers from 0.40 to 1.10
A 0.015-scale model of a modified version of the MDAC space shuttle booster was tested to obtain force, static stability, and control effectiveness data. The objective of this test was the reduction of cruise (M = 0.4) base drag by the use of base flaps, base vents, elevon deflection and base flow from a plenum mounted forward of the base heat shield. Transonic data were also obtained to determine the aerodynamic characteristics of the new base shape. Six component aerodynamic force and moment data were recorded over an angle of attack range from 4 deg to 20 deg at 0 deg sideslip and over a sideslip range from -6 deg to 6 deg at 0 deg, 6 deg and 15 deg angle of attack. Mach number varied from 0.4 to 1.10 at a constant R of 2 million per unit length.
Bradley, D.↗
Free-flight base pressure and heating measurements on sharp and blunt cones in a shock tunnel.
Nose bluntness and cone angle effects on base pressure and heating in laminar hypersonic flow regime, using free flight telemetry technique
BASE PRESSURE↗