Search NASA⌕ Search

SEARCH · Search NASA

Results for “Batch Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Modeling of photodegradation in solar cell modules of substrate and superstrate design made with ethylene-vinyl acetate as pottant material

The rates of hydrogen abstraction by peroxy radicals were proven to be too slow for significant oxidation of the alkane substrate to be important. The numerical procedure, independent of our particular data base was verified by reproducing concentration time profiles for a model reaction set describing the cesium flare system in the upper atmosphere. Simulation was identical to that given in the literature. Experimental verification of the data base is to be attempted by weatherometry studies in the coming year. Work on the new diagnostic techniques was completed. The adapted automated viscometer was demonstrated to be an efficient and reliable tool for routine measurements of viscosity (molecular weight) changes in solid samples after batch solutions have been made up. The laser photolysis GC method for monitoring extremely low levels of oxidation in polymers proved to be impractical because the yields of carbon monoxide were too low for quantification. Much progress was made with the computer model. The reaction matrix was completely revised, resulting in a new scheme of 31 reactions and time, lifetimes in excess of ten years. The results to date lead us to some tentative observations.

Somersall, A. C.↗
NASA NTRS1988

GOES dynamic propagation of attitude

The spacecraft in the next series of Geostationary Operational Environmental Satellites (GOES-Next) are Earth pointing and have 5-year mission lifetimes. Because gyros can be depended on only for a few years of continuous use, they will be turned off during routine operations. This means attitude must, at times, be determined without benefit of gyros and, often, using only Earth sensor data. To minimize the interruption caused by dumping angular momentum, these spacecraft have been designed to reduce the environmental torque acting on them and incorporate an adjustable solar trim tab for fine adjustment. A new support requirement for GOES-Next is that of setting the solar trim tab. Optimizing its setting requires an estimate of the unbalanced torque on the spacecraft. These two requirements, determining attitude without gyros and estimating the external torque, are addressed by replacing or supplementing the gyro propagation with a dynamic one, that is, one that integrates the rigid body equations of motion. By processing quarter-orbit or longer batches, this approach takes advantage of roll-yaw coupling to observe attitude completely without Sun sensor data. Telemetered momentum wheel speeds are used as observations of the unbalanced external torques. GOES-Next provides a unique opportunity to study dynamic attitude propagation. The geosynchronous altitude and adjustable trim tab minimize the external torque and its uncertainty, making long-term dynamic propagation feasible. This paper presents the equations for dynamic propagation, an analysis of the environmental torques, and an estimate of the accuracies obtainable with the proposed method.

Markley, F. Landis↗
NASA NTRS2002

Recovery of resources for advanced life support space applications: effect of retention time on biodegradation of two crop residues in a fed-batch, continuous stirred tank reactor

Bioreactor retention time is a key process variable that will influence costs that are relevant to long distance space travel or long duration space habitation. However. little is known about the effects of this parameter on the microbiological treatment options that are being proposed for Advanced Life Support (ALS) systems. Two bioreactor studies were designed to examine this variable. In the first one, six retention times ranging from 1.3 to 21.3 days--were run in duplicate, 81 working-volume continuous stirred tank reactors (CSTR) that were fed ALS wheat residues. Ash-free dry weight loss, carbon mineralization, soluble TOC reduction, changes in fiber content (cellulose, hemicellulose, and lignin), bacterial numbers, and mineral recoveries were monitored. At short retention times--1.33 days--biodegradation was poor (total: 16-20%, cellulose - 12%, hemicellulose - 28%) but soluble TOC was decreased by 75-80% and recovery of major crop inorganic nutrients was adequate, except for phosphorus. A high proportion of the total bacteria (ca. 83%) was actively respiring. At the longest retention time tested, 21.3 days, biodegradation was good (total: 55-60%, cellulose ca. 70%, hemicellulose - ca. 55%) and soluble TOC was decreased by 80%. Recovery of major nutrients, except phosphorus, remained adequate. A very low proportion of total bacteria was actively respiring (ca. 16%). The second bioreactor study used potato residue to determine if even shorter retention times could be used (range 0.25-2.0 days). Although overall biodegradation deteriorated, the degradation of soluble TOC continued to be ca. 75%. We conclude that if the goal of ALS bioprocessing is maximal degradation of crop residues, including cellulose, then retention times of 10 days or longer will be needed. If the goal is to provide inorganic nutrients with the smallest volume/weight bioreactor possible, then a retention time of 1 day (or less) is sufficient.

Non-NASA Center↗
NASA NTRS1974

Titanium honeycomb acoustic lining structural and thermal test report

The results are presented of static, fatigue and thermal testing of titanium honeycomb acoustic panels representing the acoustic tailpipe for the Pratt and Whitney Aircraft JT8D Refan engine which is being studied for use on the Boeing 727-200 airplane. Test specimens represented the engine and tailpipe flange joints, the rail to which the thrust reverser is attached and shear specimens of the tailpipe honeycomb. Specimens were made in four different batches with variations in configuration, materials and processes in each. Static strength of all test specimens exceeded the design ultimate load requirements. Fatigue test results confirmed that aluminum brazed titanium, as used in the Refan tailpipe design, meets the fatigue durability objectives. Quality of welding was found to be critical to life, with substandard welding failing prematurely, whereas welding within the process specification exceeded the panel skin life. Initial fatigue testing used short grip length bolts which failed prematurely. These were replaced with longer bolts and subsequent testing demonstrated the required life. Thermal tests indicate that perforated skin acoustic honeycomb has approximately twice the heat transfer of solid skin honeycomb.

Joynes, D.↗
NASA NTRSDate not supplied

NASA GeneLab Multi-study Visualization Portal

NASA GeneLab has helped advance the field of Space Biology by providing a public repository where researchers can store, share, analyze and visualize the results of space flight related omics experiments. The GeneLab data visualization portal allows any user, regardless of bioinformatics knowledge or access to computational resources, to interact with the experimental data, draw their own conclusions, and gain insights about the effects of space on living systems. These tools help democratize scientific research and foster the NASA Open Science initiative. The new multi-study feature of the GeneLab visualization platform allows users to mine study metadata from RNA sequencing (RNA-seq) experiments to identify samples of interest by filtering datasets based on organism, tissue, assay technology type, and/or factor. Once samples are selected from multiple datasets, users can combine and normalize the sample data, then utilize the visualization displays, including Principal Component Analysis (PCA) plots, to assess sample distributions. Finally, users can perform differential gene expression analysis on the combined data and visualize the results through PCA plots, Volcano plots, Pair plots, Heatmap, Ideogram and Gene Set Enrichment Analysis. All user-generated results and visualizations will be available for download. Here, we present a biological study using samples from multiple GeneLab RNA-seq datasets and analyzed using the multi-study visualization platform to demonstrate inter- and intra-study variability, as well as commonly differentially expressed genes between spaceflight and ground control conditions across datasets. This new feature opens a wide range of possibilities and opportunities for further development including combining other assay technology types and integration with batch effect correction techniques and machine learning applications. Overall, this tool allows users to increase the statistical power of individual experiments, validate hypothesis, identify patterns, and opens the door to new and exciting research.

space biology↗
NASA NTRS2002

GPS-Based Navigation And Orbit Determination for the AMSAT AO-40 Satellite

The AMSAT OSCAR-40 (AO-40) spacecraft occupies a highly elliptical orbit (HEO) to support amateur radio experiments. An interesting aspect of the mission is the attempted use of GPS for navigation and attitude determination in HEO. Previous experiences with GPS tracking in such orbits have demonstrated the ability to acquire GPS signals, but very little data were produced for navigation and orbit determination studies. The AO-40 spacecraft, flying two Trimble Advanced Navigation Sensor (TANS) Vector GPS receivers for signal reception at apogee and at perigee, is the first to demonstrate autonomous tracking of GPS signals from within a HEO with no interaction from ground controllers. Moreover, over 11 weeks of total operations as of June 2002, the receiver has returned a continuous stream of code phase, Doppler, and carrier phase measurements useful for studying GPS signal characteristics and performing post-processed orbit determination studies in HEO. This paper presents the initial efforts to generate AO-40 navigation solutions from pseudorange data reconstructed from the TANS Vector code phase, as well as to generate a precise orbit solution for the AO-40 spacecraft using a batch filter.

Davis, George↗
NASA NTRS1954

Study of the physical properties of petrolatum-stabilized magnesium-hydrocarbon slurry fuels

Magnesium-hydrocarbon slurries containing a moderate proportion of petrolatum have physical properties such that they offer promise as experimental aircraft fuels. The settling of the magnesium is greatly retarded by the petrolatum, and the slurries can easily be remixed to their original condition after storage. Successive batches which have closely similar properties can be prepared readily. The apparent viscosity of these slurries increased rapidly with increasing magnesium concentration, with increasing petrolatum concentration, and with decreasing temperature. As the apparent viscosity increased, the extent of settling and the ease of remixing both decreased. Although no quantitative correlation was found between the properties of the slurry and those of the petrolatum, and no one petrolatum gave slurries which were best in all respects, one of the five petrolatum used was judged to be superior to the others.

FUELS - PROPERTIES, PHYSICAL AND CHEMICAL↗
NASA NTRS1995

Study of Resource Recovery and Epidemiology in an Anaerobic Digester

Three 4-liter packed bed anaerobic digesters were fabricated and operated at 35 degrees C, pH around 7, and hydraulic retention time (HRT) of 20, 10 and 5 days to study the resource recovery and epidemiology in a controlled ecological life support system (CELSS). A simulated wastewater, consisted of shower water, clothwash water, dishwasher water, handwash water, and urine flush water was used as the feeding solution. Under steady-state operation, chemical oxygen demand (COD), total organic carbon (TOC), pH, nitrogen, phosphorus, and potassium wer monitored in the digester input and output solutions. The volume and the CH4/CO2 ratios in the biogas produced from the anaerobic digesters were measured. The results indicate about 90 percent of TOC is converted while only 5-8 percent of N-P-K are consumed in the digester. A multi-drug resistant strain of Salmonella choleraesuis was used as the indicator bacterium in the epidemiology study. The levels of Salmonella choleraesuis in the influent and the effluent wer determined and decimal decay rate constants, k(d), were estimated. The k(d) values were greater at higher initial doses than lower doses for the same HR, and greater for batch digestion (7.89/d) than for continuous digestion (4.28, 3.82, and 3.82/d for 20, 10, and 5 d HRT, respectively).

Li, K. Y.↗
NASA NTRS2018

Corrosion Failure in Electronic Devices for Aerospace Application

Corrosion of complex electronic systems is a growing and expensive concern. New materials and technology are constantly being introduced to increase performance of devices. There are many factors that can induce a corrosive environment during the various stages of manufacturing, processing, transport, and storage of these devices. The scope of this paper was to identify potential causes for the corrosion failure of optocoupler batches being used in launch applications. Optical microscope with surface profile measurements, scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS) were used to identify and analyze the source of these failure. These studies revealed that the loss of adhesion between the electrolytic plated gold and nickel layers is the critical area that traps impurity ions into the chip allowing for blisters to form along the pins of the optocoupler.

Corrosion↗
NASA NTRS2010

Employing ISRU Models to Improve Hardware Design

An analytical model for hydrogen reduction of regolith was used to investigate the effects of several key variables on the energy and mass performance of reactors for a lunar in-situ resource utilization oxygen production plant. Reactor geometry, reaction time, number of reactors, heat recuperation, heat loss, and operating pressure were all studied to guide hardware designers who are developing future prototype reactors. The effects of heat recuperation where the incoming regolith is pre-heated by the hot spent regolith before transfer was also investigated for the first time. In general, longer reaction times per batch provide a lower overall energy, but also result in larger and heavier reactors. Three reactors with long heat-up times results in similar energy requirements as a two-reactor system with all other parameters the same. Three reactors with heat recuperation results in energy reductions of 20 to 40 percent compared to a three-reactor system with no heat recuperation. Increasing operating pressure can provide similar energy reductions as heat recuperation for the same reaction times.

Linne, Diane L.↗
NASA NTRS1972

Design and development of a prototype wet oxidation system for the reclamation of water and the disposition of waste residues onboard space vehicles

Laboratory investigations to define optimum process conditions for oxidation of fecal/urine slurries were conducted in a one-liter batch reactor. The results of these tests formed the basis for the design, fabrication, and testing of an initial prototype system, including a 100-hour design verification test. Areas of further development were identified during this test. Development of a high pressure slurry pump, materials corrosion studies, oxygen supply trade studies, comparison of salt removal water recovery devices, ammonia removal investigation, development of a solids grinder, reactor design studies and bearing life tests, and development of shutoff valves and a back pressure regulator were undertaken. The development work has progressed to the point where a prototype system suitable for manned chamber testing can be fabricated and tested with a high degree of confidence of success.

Jagow, R. B.↗
NASA NTRS1988

On the cyclic stress-strain behaviour of a Ni-base superalloy at room temperature

The cyclic stress-strain behavior of Nimonic alloy PE16 was studied at room temperature and at different aging conditions to determine whether the plateau in the cyclic stress-strain curve (CSSC) reported by Arbuthnot (1982) is typical of the room temperature behavior and/or some specific initial microstructural states. Specimen blanks were heat-treated in batches in Ar/H2 (98/2) atmosphere to produce gamma-prime precipitates of different average sizes, but with the volume fraction of gamma-prime precipitates kept constant at about 7 percent at all the heat-treatment conditions. Total axial strain controlled LCF tests were conducted under fully reversed loading (R = -1) at a constant strain rate of 0.004/s, using a servohydraulic machine. The load response in tension and compression was recorded continually, and stress-strain hysteresis loops were recorded at frequent intervals. In the present investigation, the CSSCs of the P16 alloy at room temperature did not display the plateaus reported by Arbuthnot.

Singh, Vakil↗
NASA NTRS1995

Gas chromatography/ion mobility spectrometry as a hyphenated technique for improved explosives detection and analysis

Ion Mobility Spectrometry (IMS) is currently being successfully applied to the problem of on-line trace detection of plastic and other explosives in airports and other facilities. The methods of sample retrieval primarily consist of batch sampling for particulate residue on a filter card for introduction into the IMS. The sample is desorbed into the IMS using air as the carrier and negative ions of the explosives are detected, some as an adduct with a reagent ion such as Cl(-). Based on studies and tests conducted by different airport authorities, this method seems to work well for low vapor pressure explosives such as RDX and PETN, as well as TNT that are highly adsorptive and can be found in nanogram quantities on contaminated surfaces. Recently, the changing terrorist threat and the adoption of new marking agents for plastic explosives has meant that the sample introduction and analysis capabilities of the IMS must be enhanced in order to keep up with other detector developments. The IMS has sufficient analytical resolution for a few threat compounds but the IMS Plasmogram becomes increasingly more difficult to interpret when the sample mixture gets more complex.

Mercado, AL↗
NASA NTRS1979

Shoe-box orbit determination system for SMM preliminary results

The implementation of both sequential and batch methods of estimation on IMP-16 microprocessors was investigated. Simulated data was used from a tracking and data relay satellite whose target satellite was the Solar Maximum Mission. An interesting feature of the hardware was the use of two interconnected IMP-16's. Some preliminary results from the study, as well as the difficulties and advantages in the use of microprocessors, are presented.

Tasaki, K. K.↗
NASA NTRS1988

Laboratory produced P/M aluminum 2XXX + Zr sheet

A laboratory-scale batch of aluminum alloy sheeting samples in the 2XXX + Zr system has been produced by P/M techniques in the T8X temper and subjected to tensile and Kahn tear property tests in both the longitudinal and long-transverse directions. The results obtained were compared to those of a NASA study concerning the same alloy powders; it appears that laboratory production-scale sheet-sample properties are good to excellent predictors of pilot-scale process products' tensile and tear notch toughness properties. The tear resistance toughness of the laboratory samples was not predictive of the pilot-scale products, however.

Royster, Dick M.↗
NASA NTRS1993

Chemical analyses of provided samples

Two batches of samples were received and chemical analysis was performed of the surface and near surface regions of the samples by the surface analysis by laser ionization (SALI) method. The samples included four one-inch optics and several paint samples. The analyses emphasized surface contamination or modification. In these studies, pulsed sputtering by 7 keV Ar+ and primarily single-photon ionization (SPI) by coherent 118 nm radiation (at approximately 5 x 10(exp 5) W/cm(sup 2) were used. For two of the samples, also multiphoton ionization (MPI) at 266 nm (approximately 5 x 10(exp 11) W/cm(sup 2) was used. Most notable among the results was the silicone contamination on Mg2 mirror 28-92, and that the Long Duration Exposure Facility (LDEF) paint sample had been enriched in K and Na and depleted in Zn, Si, B, and organic compounds relative to the control paint.

Becker, Christopher H.↗
NASA NTRS1986

Investigation of porous polymer gas chromatographic packings for atmospheric analysis of extraterrestrial bodies

Measurement of the permanent gases in the atmospheres of mission targets is a major objective. A 16 meter long Porapak N column was used on the Venus probe and required a rather high carrier gas flow rate. The researchers have, therefore, surveyed commercial porous polymer types which had some ability to resolve nitrogen, oxygen, argon and carbon monoxide gases. Porapaks N and Q appeared superior to most. Batch to batch variation, however, was quite wide, so the researchers learned how to synthesize porous polymer and investigated some of the factors affecting the separations. A polymer was synthesized which was superior to all commercial products and allowed at least a 50% reduction in length and flow rate of carrier gas. Similar studies were made concerning the separation of hydrocarbons and new porous polymers have been synthesized which represent significant improvements in time of analysis, column, and carrier gas flow rate.

Pollock, G. E.↗
NASA NTRS2024

Xplo-SA9T: Optimization of Sorbent Technology With Existing and New Amine Variants for Carbon Dioxide Removal and Humidity Control

Scrubbing of the spacesuit air stream to control humidity and regulate carbon dioxide (CO 2 ) relies on amine-loaded resins, colloquially known as sorbents. The efficacy of Rapid Cycle Amine technology relies on the propensity of nitrogens toward adsorption of CO 2 while simultaneously offering regenerative properties under vacuum or positive pressure. The commonly utilized sorbent, SA9T, was recreated and evaluated further to increase stability and serve as a benchmark comparison for newly synthesized amine sorbent technologies. Ongoing storage studies with eight different environments will allow the development of applicable storage protocols and provide insight into possible ammonia generation pathways. Attempts to alleviate the known issues with SA9T included the alteration of the primary amine (tetraethylenepentamine), the choice of resin, and the particle size distribution. In-house CO 2 breakthrough experiments were conducted using a specialized apparatus that can simulate spacesuit conditions, offering high-quality triplicate capacity analysis affording direct comparison to known adsorbents in the literature. Thermo-Desorption Gas Chromatography Mass Spectrometry studies on the synthesized materials revealed any reagent or solvent offgassing while Nuclear Magnetic Resonance spectroscopy tracked the stability of the bound amine. Scanning Electron Microscope images of sieved materials provided a more accurate size interpretation facilitating synthetic design and pressure drop elimination. All efficient sorbents were synthesized to a commercial batch scale subsequent to evaluation including Xplo-SA9T.

John R Tidwell↗