SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An initial definition of on-board processing requirements for an advanced satellite communications system to service domestic markets in the 1990's is presented. An exemplar system architecture with both RF on-board switching and demodulation/remodulation baseband processing was used to identify important issues related to system implementation, cost, and technology development.
The initial definition of on-board processing for an advanced satellite communications system to service domestic markets in the 1990's is discussed. An exemplar system with both RF on-board switching and demodulation/remodulation baseband processing is used to identify important issues related to system implementation, cost, and technology development. Analyses of spectrum-efficient modulation, coding, and system control techniques are summarized. Implementations for an RF switch and baseband processor are described. Among the major conclusions listed is the need for high gain satellites capable of handling tens of simultaneous beams for the efficient reuse of the 2.5 GHz 30/20 frequency band. Several scanning beams are recommended in addition to the fixed beams. Low power solid state 20 GHz GaAs FET power amplifiers in the 5W range and a general purpose digital baseband processor with gigahertz logic speeds and megabits of memory are also recommended.
CADAT printed-wiring-board system (PWB) designs printed-circuit and hybrid-circuit boards. It is comprised of four programs: preprocessor, placement program, organizer program, and the router. Component placement and interconnection paths are optimized.
The NASA-NEEDS program goals present a requirement for on-board signal processing to achieve user-compatible, information-adaptive data acquisition. One very specific area of interest is the preprocessing required to register imaging sensor data which have been distorted by anomalies in subsatellite-point position and/or attitude control. The concepts and considerations involved in using state-of-the-art positioning systems such as the Global Positioning System (GPS) in concert with state-of-the-art attitude stabilization and/or determination systems to provide the required registration accuracy are discussed with emphasis on assessing the accuracy to which a given image picture element can be located and identified, determining those algorithms required to augment the registration procedure and evaluating the technology impact on performing these procedures on-board the satellite.
Snowpack properties such as water equivalent and snow wetness may be inferred from variations in measured microwave brightness temperatures. This is because the emerged microwave radiation interacts directly with snow crystals within the snowpack. Using vertically and horizontally polarized brightness temperatures obtained from the multifrequency microwave radiometer (MFMR) on board a NASA research aircraft and the electrical scanning microwave radiometer (ESMR) and scanning multichannel microwave radiometer (SMMR) on board the Nimbus 5, 6, and 7 satellites, linear relationships between snow depth or water equivalent and microwave brightness temperature were developed. The presence of melt water in the snowpack generally increases the brightness temperatures, which can be used to predict snowpack priming and timing of runoff.
On-board real time flight control is studied in order to develop algorithms which are simple enough to be used in practice, for a variety of missions involving three dimensional flight. The intercept mission in symmetric flight is emphasized. Extensive computation is required on the ground prior to the mission but the ensuing on-board exploitation is extremely simple. The scheme takes advantage of the boundary layer structure common in singular perturbations, arising with the multiple time scales appropriate to aircraft dynamics. Energy modelling of aircraft is used as the starting point for the analysis. In the symmetric case, a nominal path is generated which fairs into the dash or cruise state. Feedback coefficients are found as functions of the remaining energy to go (dash energy less current energy) along the nominal path.
In 1976 NASA awarded The Boeing Company a contract to develop IPAD (Integrated Programs for Aerospace-Vehicle Design). This contract included a requirement for Boeing to form an Industrial Technical Advisory Board (ITAB), with members representing major aerospace and computer companies. The purpose of this board was to guide the development of IPAD. The specific goal of IPAD is to increase United States aerospace industry productivity through the application of computers to manage engineering data. This goal clearly is attainable; in fact, IPAD's influence can reach beyond the aerospace industry to many businesses where product development is based on the design-building process. An enhanced IPAD, therefore, is a national asset of significance. The role of ITAB in guiding the development of this system is described.
On-board real time flight control is studied in order to develop algorithms which are simple enough to be used in practice, for a variety of missions involving three dimensional flight. The intercept mission in symmetric flight is emphasized. Extensive computation is required on the ground prior to the mission but the ensuing on-board exploitation is extremely simple. The scheme takes advantage of the boundary layer structure common in singular perturbations, arising with the multiple time scales appropriate to aircraft dynamics. Energy modelling of aircraft is used as the starting point for the analysis. In the symmetric case, a nominal path is generated which fairs into the dash or cruise state.
The agenda of the Aeronautics and Space Engineering Board meeting is reviewed. Items discussed included; engineering and technical requirements of the space station, NASA's altitude wind tunnel, rocket engine casings, advanced flight vehicle technology, the space shuttle, and on-orbit space maintenance. Board members along with their institutional affiliation are listed.
On-board real time flight control is studied in order to develop algorithms which are simple enough to be used in practice, for a variety of missions involving three-dimensional flight. The intercept mission in symmetric flight is emphasized. Extensive computation is required on the ground prior to the mission but the ensuing on-board exploitation is extremely simple. The scheme takes advantage of the boundary layer structure common in singular perturbations, arising with the multiple time scales appropriate to aircraft dynamics. Energy modelling of aircraft is used as the starting point for the analysis. In the symmetric case, a nominal path is generated which fairs into the dash or cruise state. Previously announced in STAR as N84-16116
Damage to connectors reduced and special tools not needed. Clockwise rotation of screw tightens wedges against mounting body and right heat sink. Counterclockwise rotation of screw drives bottom wedge downward and jacking ring upward, pulling pins away from mating connector. Screw in mechanism turned to produce jacking force that disengages board from mating connector. Force parallel to connector pins do not bend or brake. When disengaged, board protrudes from assembly and readily grasped by operator.
The NASA requirements for assuring reliable rigid printed wiring board design are prescribed. Basic considerations necessary to assure reliable rigid printed wiring board design are described and incorporated.
An interactive computer-graphics-based tool for specifying the placement of electronic parts on a wire-wrap circuit board is presented. Input is a data file (currently produced by a commercial logic design system) which describes the parts used and their interconnections. Output includes printed reports describing the parts and wire paths, parts counts, placement lists, board drawing, and a tape to send to the wire-wrap vendor. The program should reduce the engineer's layout time by a factor of 3 to 5 as compared to manual methods.
An Expert System is described which Rockwell Satellite and Space Electronics Division (S&SED) is developing to dynamically schedule the allocation of on-board satellite resources and activities. This expert system is the Satellite Controller. The resources to be scheduled include power, propellant and recording tape. The activities controlled include scheduling satellite functions such as sensor checkout and operation. The scheduling of these resources and activities is presently a labor intensive and time consuming ground operations task. Developing a schedule requires extensive knowledge of the system and subsystems operations, operational constraints, and satellite design and configuration. This scheduling process requires highly trained experts anywhere from several hours to several weeks to accomplish. The process is done through brute force, that is examining cryptic mnemonic data off line to interpret the health and status of the satellite. Then schedules are formulated either as the result of practical operator experience or heuristics - that is rules of thumb. Orbital operations must become more productive in the future to reduce life cycle costs and decrease dependence on ground control. This reduction is required to increase autonomy and survivability of future systems. The design of future satellites require that the scheduling function be transferred from ground to on board systems.
The Topex/Poseidon satellite requires real-time on-board knowledge of the satellite and TDRS ephemeris for attitude determination and control and High-Gain Antenna (HGA) pointing. The ephemeris representation concept for the MMS (Multimission Modular Spacecraft) satellites has shown that compressing the predicted ephemeris in a Fourier Power Series (FPS) before uplinking in conjunction with the On-Board Computer (OBC) ephemeris reconstruction algorithms is an efficient technique for ephemeris representation. As an MMS-based satellite, Topex/Poseidon has inherited the Landsat ephemeris representation concept including a daily FPS upload. This paper presents the Topex/Poseidon concept, analysis, and results including the conclusion that the ephemeris representation duration could be extended to 10 days or more and convenient weekly uploading is adopted without an increase in OBC memory requirements.
A computer-controlled multichannel pressure measurement system was developed to acquire detailed flow field measurements on board the Large Low Speed Centrifugal Compressor Research Facility at the NASA Lewis Research Center. A pneumatic slip ring seal assembly is used to transfer calibration pressures to a reference standard transducer on board the compressor rotor in order to measure very low differential pressures with the high accuracy required. A unique data acquisition system was designed and built to convert the analog signal from the reference transducer to the variable frequency required by the multichannel pressure measurement system and also to provide an output for temperature control of the reference transducer. The system also monitors changes in test cell barometric pressure and rotating seal leakage and provides an on screen warning to the operator if limits are exceeded. The methods used for the selection and testing of the the reference transducer are discussed, and the data acquisition system hardware and software design are described. The calculated and experimental data for the system measurement accuracy are also presented.
The very large scale integration (VLSI) implementation of a fuzzy logic inference mechanism allows the use of rule-based control and decision making in demanding real-time applications. Researchers designed a full custom VLSI inference engine. The chip was fabricated using CMOS technology. The chip consists of 688,000 transistors of which 476,000 are used for RAM memory. The fuzzy logic inference engine board system incorporates the custom designed integrated circuit into a standard VMEbus environment. The Fuzzy Logic system uses Transistor-Transistor Logic (TTL) parts to provide the interface between the Fuzzy chip and a standard, double height VMEbus backplane, allowing the chip to perform application process control through the VMEbus host. High level C language functions hide details of the hardware system interface from the applications level programmer. The first version of the board was installed on a robot at Oak Ridge National Laboratory in January of 1990.
A method is discussed developed to verify commercial printed-circuit boards for a shuttle orbital flight. The Space Acceleration Measurement System Project used this method first with great success. The test sequence is based on early fault detection, desire to test the final assembly, and integration with other verification testing. A component thermal screening test is performed first to force flaws in design, workmanship, parts, processes, and materials into observable failures. Then temperature definition tests are performed that consist of infrared scanning, thermal vacuum testing, and preliminary thermal operational testing. Only the engineering unit is used for temperature definition testing, but the preliminary thermal operational testing is performed on the flight unit after the temperature range has been defined. In the sequence of testing, vibration testing is performed next, but most vibration failures cannot be detected without subsequent temperature cycling. Finally, final assembly testing is performed to simulate the shuttle flight. An abbreviated thermal screening test is performed as a check after the vibration test, and then a complete thermal operational test is performed. The final assembly test finishes up with a burn-in of 100 hours of trouble-free operation. Verification is successful when all components and final assemblies have passed each test satisfactory. This method was very successful in verifying that commercial printed-circuit boards will survive in the shuttle environment.