Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Improving Cost and Efficiency of the Scalable Solid Oxide Fuel Cells Power System

The objective of this project was to design and develop a 20kW range small-scale solid oxide fuel cells (SOFC) power system for applications such as data centers and commercial buildings. The original plan included a 5,000 hours demonstration and a Techno-Economic Analysis (TEA) which were dropped as part of project termination. The original project plan was to use a stack with a cross-flow cell design which had previously been tested for 500 hours at a community college in Malta, NY. However, it was decided to move to the advanced R-SOFC co-flow cell developed under Department of Energy Award DE-FE0031971. The advanced cell design has the advantage of a larger active area for the same manufacturing footprint which results in fewer required cells for the same stack power, hence a higher volumetric power density (kW/L) and lower cost per kW than the original cross-flow cell design. A full SOFC system Simulink model was developed and calibrated with testing data from a fuel cell stack and BOP (balance of plant) components. The simulation results from the calibrated model showed an acceptable match with the experimental data. A structural analysis conducted for various load scenarios indicated no high stress areas for all spatial directions. Major electrical system components were acquired, built and successfully tested. System sensors were verified and validated against controls. Safety checks, a diagnostic check, PID tuning, and control software commissioning tasks were also conducted. The power electronics prototype was delivered and trial testing completed. Balance of Plant component testing and simulation work was conducted to characterize Reformer-Heat Exchanger heat transfer and backpressure and reformer catalyst methane conversion and product selectivity. Simulations were conducted to design the Anode and Cathode fluid passages and size the air-air and fuel-fuel heat exchangers. A Burner operation map was created from test data and the Anode Gas Recirculation blower was tested to evaluate its durability. The SOFC system used a horizontal style design where components sit directly on a casting with a direct connection to the skid. This design has efficient packaging and a small footprint with approximate dimensions of 750 mm x 700 mm x 1700 mm. An SOFC system was built and successfully tested at the Malta, NY facility The system for over 500 hours under load of which over 300 hours was at full load of 20 kW.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

In-Cell Deployment and First Use of Digital Image Correlation for In-Situ Strain Analysis of Irradiated Nuclear Fuel Rods During LOCA Transient

Digital image correlation (DIC) is a noncontact, optical method increasingly used across industries and research environments for acquiring multidimensional strain data. At Oak Ridge National Laboratory’s (ORNL’s) Severe Accident Test Station (SATS), DIC has been extensively applied to study the thermomechanical response of nuclear fuel claddings, yielding fundamental insights into material behavior. However, these efforts have focused exclusively on unirradiated materials and relied on the SATS out-of-cell infrastructure. Efforts over the past two years have been made to extend these capabilities to ORNL’s Irradiated Fuels Examination Laboratory SATS system within the hot-cells to enable testing of irradiated fuel cladding materials. Integrating DIC into the hot-cell SATS infrastructure presents unique challenges, including enabling remote operation of optical equipment and adapting auxiliary hot-cell systems for DIC implementation. This report discusses design, stand-up testing, and application of DIC to an irradiated nuclear fuel cladding segment. A DIC testing rig was successfully built and validated out-of-cell through extensive surrogate tests and calibrations. The rig and specialized DIC furnace were installed in the hot-cell, and a DIC test was successfully conducted. Results from that test correspond to expectations for Zr-based alloys and showed similar uncertainties compared to out-of-cell tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

scPlantAnnotate: an accurate and robust transformer-based model for plant cell type annotation

Accurate cell type annotation remains a major bottleneck in plant single-cell RNA sequencing (scRNA-seq), where existing tools are often adapted from animal studies and perform sub-optimally on plant data. The lack of plant-specific computational frameworks limits the construction of plant cell atlases and downstream biological discovery. We develop and evaluate scPlantAnnotate, a Transformer-based reference annotation framework tailored for plant scRNA-seq data, and benchmark it against state-of-the-art deep learning and conventional methods across multiple plant species. Species-specific scPlantAnnotate models were trained using curated datasets from Arabidopsis thaliana, Zea mays, Oryza sativa, and Glycine max. We compared scPlantAnnotate with leading baselines under both standard random-split evaluation and a more stringent leave-one-dataset-out setting, which tests robustness to completely unseen datasets and tissue types. scPlantAnnotate consistently outperforms existing approaches across all four species under random-split evaluation. In the leave-one-dataset-out setting for A. thaliana, where performance drops markedly for all methods due to strong batch effects and dataset heterogeneity, scPlantAnnotate nonetheless achieves the highest Accuracy, Macro-F1, Balanced Accuracy, and Macro-AUROC on average and ranks first on most held-out datasets. These results demonstrate improved robustness to dataset shifts, a critical yet underexplored challenge in plant scRNA-seq analysis. A freely accessible web server enables users to annotate their own datasets using pretrained models. scPlantAnnotate provides a plant-specific, Transformer-based framework for single-cell annotation that delivers state-of-the-art performance and enhanced robustness to unseen datasets. By addressing limitations of existing tools and enabling scalable reference-based annotation, scPlantAnnotate supports the development of comprehensive plant cell atlases and facilitates broader use of single-cell genomics in plant biology.

Bioinformatics↗
DOE OSTI2024

Technoeconomic Analysis of Discrete and Unitized Reversible Fuel Cells for Energy Storage Applications

Reversible Fuel Cell (RFC) systems offer promising characteristics for stationary long duration energy storage applications. Two main configurations of RFC systems exist: discrete RFC systems and unitized RFC systems. While discrete RFC systems combine independent fuel cell and electrolyzer systems for energy storage, unitized RFC systems utilize a single electrochemical stack and might share balance of plant (BOP) components for both charging and discharging processes. While this configuration reduces upfront capital costs, challenges of unitized RFC designs include potential performance trade-offs due to dual-mode stack design and operational complexities across varying loads and operating conditions. Furthermore, these tradeoffs might be different for low-temperature PEM RFCs than for high-temperature reversible solid oxide cell systems. The goal of this project is to assess unitized RFC system potential in the context of long duration grid energy storage and HFTO's technical targets for different discrete fuel cell and electrolyzer technologies. This presentation presents preliminary review of state-of-the-art unitized RFC cells and assesses how they perform relative to HFTO's technical targets. It also presents literature-derived system configurations worth investigating. This review indicates that lab-scale unitized RFCs are making good progress towards meeting HFTO's technical targets.

HYDROGEN↗
DOE OSTI2025

Low-Cost, Screen-Printed Silver Metal Complex Inks for Silicon Heterojunction Solar Cells

Screen printing using metal particle pastes, the current photovoltaic industry metallization standard, provides fast and reliable metal grids for silicon solar cells. Recently, metal complex or reactive metal inks are attracting research interest due to their significantly low cost and higher performance compared to traditional nanoparticle silver pastes. In this work, we demonstrate, for the first time, screen-printed high-efficiency silicon heterojunction solar cells metallized by silver metal complex inks on industrial G1-size (158.75 x 158.75 mm2) wafers. We demonstrate screen-printed Ag metal complex ink grid patterns with continuous fingers ~100-120 ..mu..m wide. The printed Ag grid is very thin (~1 ..mu..m), which is an order of magnitude thinner than the current ~20-30 ..mu..m fingers printed with low-temperature nanoparticle-based pastes. Double printing allows silicon heterojunction devices with efficiencies >20%. This is the highest efficiency so far, to our knowledge, of industrial solar cell precursors using this metallization technology. Simulation results suggested that increasing the thickness of the metal film does not significantly improve efficiency due to the dense, highly conductive films. So, a single print of ~1 ..mu..m finger would be enough to produce cells that perform similarly to a ~20 ..mu..m thick nanoparticle paste printed cells. Additionally, solar cells printed on G1 wafers with silver metal complex ink required more than 10 times less silver (~0.03 g) compared to those using silver/copper nanoparticle paste (~0.4 g of Ag). These results indicate that metal complex inks are a very promising replacement for silver nanoparticle pastes for industrial-scale metallization in an age of resource scarcity and high costs of noble metals.

14 SOLAR ENERGY↗
DOE OSTI2024

Mechanical Design Guidelines to Inhibit Fracture in Perovskite Solar Cells

Perovskite (PVSK) solar cells offer significant benefits over conventional silicon cells including low-cost solution processibility, minimal materials usage related to strong photon absorption in thin-film cell architectures, and a tunable bandgap. However, PVSK films are mechanically fragile, and fracture of PVSK layers and adjacent interfaces are a significant concern during fabrication, encapsulation, and operation. Herein, a thin-film mechanics fracture analysis tailored for p–i–n and n–i–p PVSK solar cells on both soda lime glass and polyimide substrates fabricated with three PVSK crystallization methods is presented. Here, the role of thermal processing of each cell layer is explored to determine the maximum allowable temperature below which fracture is inhibited. In the analysis, the mechanics basis for processing and materials selection guidelines for preventing fracture in PVSK solar cells is provided.

adhesion↗
DOE OSTI2026

A cell-centered AMR-ALE framework for 3D multi-material hydrodynamics. Part I: Lagrangian and indirect Euler AMR algorithms

Many applications of physics and engineering involve wide ranges of time and spatial scales. The numerical simulation of localized small scales such as shock waves and material interfaces requires a large number of computational cells in these regions. For these applications, Lagrangian and Arbitrary-Lagrangian-Eulerian (ALE) related methods are engaging since the moving mesh feature naturally brings mesh cells on shock discontinuities and material interfaces are carefully captured. In addition, Adaptive-Mesh-Refinement (AMR) strategies aim to optimize computational resources by concentrating finer mesh cells only in areas of interest while using coarser cells elsewhere. A key but challenging AMR requirement consists in efficiently distributing the computational effort to achieve high accuracy without the prohibitive computational costs associated with uniformly fine grids. Here, in this document, the coupling of the p4est AMR library with a cell-centered Lagrangian scheme is presented with the goal to perform reliable 3D Lagrangian-AMR and indirect Euler-AMR multi-material simulations. In particular, it is shown that starting from a 3D indirect ALE code, the memory management and load balancing requirements can be delegated to an external library (here the p4est library) to unlock ALE-AMR capabilities. First, we present a strategy to transcribe the octant-based connectivity of the 3D AMR framework with that of an unstructured mesh of polygonal cells used in Lagrangian hydrodynamics. Then, we show how refinement and coarsening operations must be adapted to the particular Lagrangian framework to ensure the conservation of volume during those steps. Finally, several numerical test cases are presented that demonstrate the capabilities of the Lagrangian-AMR and indirect Euler-AMR algorithms.

3D cell-centered Lagrangian numerical scheme↗
DOE OSTI2025

Optimizing energy yield of monolithic perovskite/silicon tandem solar cells in real-world Conditions: The impact of luminescent coupling

Efficient light management is key to maximizing power conversion efficiency (PCE) in monolithic perovskite/silicon tandem solar cells. Achieving peak efficiency requires closely matched current generation in all junctions, especially in integrated configurations. However, real-world conditions vary significantly due to factors such as sunlight spectrum, diffuse-to-direct sunlight ratio, angular distribution of light, subcell temperature coefficients, and ground reflection. This study introduces a comprehensive optical and device simulation to optimize perovskite/silicon tandem cells, considering experimental luminescent coupling (LC) efficiency and its dependence on working conditions, alongside variations in radiative recombination, effect of temperature on absorptivity spectra, and cloud cover. Our results show potential energy yield improvements of up to 1.4 % with LC, based on current perovskite radiative recombination records, and up to 4 % with direct bandgap materials. Although radiative recombination's dependence on excitation intensity reduces output power and requires thicker absorbers, LC compensates for these losses. LC also lowers the optimized bandgap for the perovskite top cell from 1.72 eV to 1.64–1.68 eV, or even lower in regions with redshifted irradiance. Additionally, optimization revealed that thinner silicon bottom cells require a higher perovskite top cell bandgap, impacting the balance between fabrication cost and cell stability.

14 SOLAR ENERGY↗
DOE OSTI2026

>24% screen printed Cu contacted n-TOPCon solar cells with successful implementation of LECO process

In this paper, we report the successful fabrication of >24.0 % efficiency n-TOPCon Si solar cells with screen-printed, fire-through Cu contact to n-TOPCon on the rear side and Ag contacted boron emitter on the front side by implementing optimized firing and LECO conditions. The highest efficiency (24.3%) Cu contacted n-TOPCon cell in this study showed excellent cell performance parameters with V oc >730 mV, J sc of 41.1 mA/cm 2 and FF of 80.8%, resulting in an absolute efficiency gap of 0.2% between Cu-contacted and fully Ag contacted n-TOPCon cells (24.5%). The mini-module fabricated with the Cu contacted n-TOPCon cell showed excellent reliability and durability of open-circuit voltage (V oc ), pseudo fill factor (pFF) and efficiency after prolonged damp-heat tests. Such high efficiency screen printed Cu contacted n-TOPCon cells provide unique opportunity to replace very expensive Ag contact on n-TOPCon with cheaper screen printable Cu metal pastes.

14 SOLAR ENERGY↗
DOE OSTI2025

Multiscale Mechanical Characterization of Mineral-Reinforced Wood Cell Walls

Studying the multiscale mechanics of bio-based composites offers unique perspectives on underlying structure–property relations. Cellular materials, such as wood, are highly organized, hierarchical assemblies of load-bearing structural elements that respond to mechanical stimuli at the microscopic, mesoscopic and macroscopic scale. In this study, we modified oak wood with nanocrystalline ferrihydrite, a widespread ferric oxyhydroxide mineral, and characterized the resulting mechanical properties of the composite at various levels of organization. Ferrihydrite nanoparticles were deposited inside the wood cell wall by an in situ chemical reaction, resulting in increased stiffness and hardness of the functionalized secondary cell wall, as evidenced by region-specific nanoindentation tests under an electron microscope. Chemically modified and pristine wood samples were characterized by using atomic force microscopy in the bimodal frequency modulation mode, which produced topographical images from the cellular ultrastructure with high lateral resolution and localized nanomechanical information across distinct cell wall layers. In conclusion, despite mineral reinforcement at the cell wall level, the macroscopic fracture behavior examined through three-point flexural testing remained unchanged upon modification, as cell–cell adhesion could be impaired by harsh chemical conditions.

Cells↗
DOE OSTI2024

Understanding Direct-Ammonia Protonic Ceramic Fuel Cells: High-Performance in the Absence of Precious Metal Catalysts

Ammonia has received considerable attention as a promising carbon-free hydrogen carrier. At temperatures above 400 °C, NH 3 is thermodynamically unstable with respect to decomposition into nitrogen and hydrogen and is, thus, suitable for direct use in solid oxide fuel cells (SOFCs) without external reforming. However, poor catalytic activity for ammonia decomposition at the moderate temperatures of protonic ceramic fuel cell (PCFC) operation has resulted in low fuel cell power output relative to operation on hydrogen and likely contributes to reported cell degradation. Here we prepared cells based on a thermodynamically robust electrolyte, a high activity cathode, and an anode with a distinctive structure to overcome challenges of poor activity and stability. Furthermore, the cells delivered peak power densities of 0.59 and 0.44 W cm –2 under H 2 and NH 3 , respectively, at 500 °C, excellent stability over a period of 200 h, and no detectable NO x in the anode exhaust gas.

25 ENERGY STORAGE↗
DOE OSTI2024

Implicating the red body of Nannochloropsis in forming the recalcitrant cell wall polymer algaenan

Stramenopile algae contribute significantly to global primary productivity, and one class, Eustigmatophyceae, is increasingly studied for applications in high-value lipid production. Yet much about their basic biology remains unknown, including the nature of an enigmatic, pigmented globule found in vegetative cells. Here, we present an in-depth examination of this “red body,” focusing on Nannochloropsis oceanica. During the cell cycle, the red body forms adjacent to the plastid, but unexpectedly it is secreted and released with the autosporangial wall following cell division. Shed red bodies contain antioxidant ketocarotenoids, and overexpression of a beta-carotene ketolase results in enlarged red bodies. Infrared spectroscopy indicates long-chain, aliphatic lipids in shed red bodies and cell walls, and UHPLC-HRMS detects a C32 alkyl diol, a potential precursor of algaenan, a recalcitrant cell wall polymer. We propose that the red body transports algaenan precursors from plastid to apoplast to be incorporated into daughter cell walls.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

A redox-reversible A/B-site co-doped BaFeO 3 electrode for direct hydrocarbon solid oxide fuel cells

Solid oxide fuel cells (SOFCs) can directly convert the chemical energy in fuel to electrical energy with fuel flexibility; however, the conventional nickel-based anodes face great challenges due to coking upon direct oxidation of hydrocarbon fuels and redox instability. Thus, developing new anode materials which can provide high coking resistance as well as redox stability is crucial. In this work, Ba 0.6 La 0.4 Fe 0.8 Mo 0.1 Ni 0.1 O 3-δ (BLFMN) has been synthesized in air using a sol–gel combustion method, resulting in a dual phase consisting of a cubic BLFMN main phase and scheelite BaMoO 4 (BMO 4 ) secondary phase. By heat-treating the BLFMN dual phase in H 2 at 800 °C for 5 h, a metallic nanoparticle-decorated BLFMN triple phase compound comprising cubic BLFMN, cubic BaMoO 3 (BMO 3 ) and in situ exsolved FeNi 3 alloy was obtained. BLFMN was subsequently investigated as an electrode material for La 0.8 Sr 0.2 Ga 0.83 Mg 0.17 O 3-δ (LSGM) electrolyte (300 μm) supported SOFCs. Symmetrical cells using BLFMN as electrodes with the cell configuration of BLFMN//LSGM//BLFMN showed excellent redox reversibility and a peak power density (PPD) of 1.32 W cm -2 at 850 °C when using H 2 as fuel. Single cell with the cell configuration of BLFMN//LSGM//LSCF (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ ) reached PPD of 1.61 and 0.41 W cm -2 at 850 °C when operating with H 2 and CH 4 fuel, respectively. Moreover, the single cell exhibit excellent stability (over 300 h) upon direct oxidation of hydrocarbon fuels of CH 4 and C 3 H 8 . This study indicates that BLFMN is a promising redox reversible and coking resistant anode for SOFCs.

08 HYDROGEN↗
DOE OSTI2025

Characterization of dangling bond defects at the crystalline Si/SiO x interface in a polycrystalline Si passivating contact solar cell at room temperature with electrically detected magnetic resonance spectroscopy

Monocrystalline silicon solar cells can achieve photoconversion efficiencies exceeding 26%; however, performance-limiting defects that trap carriers continue to be a challenge. In this work, we have characterized Si solar cells with tunneling SiO x /polycrystalline-Si (poly-Si) passivating contacts (TOPCon) on As-doped Czochralski Si wafers with electrically detected magnetic resonance (EDMR) spectroscopy. We fabricated 2 × 20 mm 2 TOPCon-like mini solar cells with edge passivation alongside larger 4 cm 2 sister cells and obtained similar device characteristics. We performed EDMR spectroscopy at 300 K on two minicells with different degrees of surface passivation based on the recombination parameter, J o , values of 40 and 310 fA/cm2. We optimized the resolution and the signal-to-noise ratio of the EDMR response of the minicells by varying the forward bias voltage and the magnetic field modulation amplitude. We detect two distinct signals with EDMR spectroscopy, an axial-like signal at g = 2.009, 2.0087, and 2.0015, and an isotropic signal at g = 2.0024, which we attribute to Si dangling bonds (P b0 and P b centers) and boron–oxygen related defects, respectively, at or near the c-Si/SiO x interface. The EDMR signals were lower for the cell with a lower value of J o , while the ratio of the two defect populations was very similar. The EDMR signal increases with forward bias but drops to zero at bias voltages >0.5 V, consistent with interface defects within or near the boron-doped emitter depletion region. Our study demonstrates a method to fabricate minicells that can be characterized with EDMR spectroscopy to detect industrially relevant defects in TOPCon cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Fundamental advantages of multijunction thermoradiative cells

Thermoradiative (TR) cells convert heat to work through emission of thermal radiation. Multijunction thermoradiative cells have received little research interest due to the apparent overlap with energy harvesting limits. Through detailed balance formalism, the present study models both single- and multi-diode TR devices, establishing their performance limits and identifying key factors that influence efficiency. For single-junction TR cells, we derive a relationship for the optimal bandgap and show that higher emitter temperatures increase efficiency. When the receiver is at absolute zero temperature, multijunction TR cells have little advantage over the single-junction cell in terms of the maximum output power density. However, for higher receiver temperatures, the multijunction configuration demonstrates significant improvements in both power and efficiency through the optimization of the chemical potential and bandgap of each diode in the complete ensemble. A 500 K emitter and 300 K receiver TR system can achieve a 21.25% increase in efficiency and a 10% improvement in the power density with multijunction architecture compared to a single junction through chemical potential optimization. These findings suggest that multijunction TR cells offer a promising approach to advancing low-grade heat recovery technologies for efficient heat-to-work conversion.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

A fungal protein organizes both glycogen and cell wall glucans

Glycogen is a glucose storage molecule composed of branched α-1,4-glucan chains, best known as an energy reserve that can be broken down to fuel central metabolism. Because fungal cells have a specialized need for glucose in building cell wall glucans, we investigated whether glycogen is used for this process. For these studies, we focused on the pathogenic yeast Cryptococcus neoformans, which causes ~150,000 deaths per year worldwide. We identified two proteins that influence formation of both glycogen and the cell wall: glycogenin (Glg1), which initiates glycogen synthesis, and a protein that we call Glucan organizing enzyme 1 (Goe1). We found that cells missing Glg1 lack α-1,4-glucan in their walls, indicating that this material is derived from glycogen. Without Goe1, glycogen rosettes are mislocalized and β-1,3-glucan in the cell wall is reduced. Altogether, our results provide mechanisms for a close association between glycogen and cell wall.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

1.1 eV GaInAs Cell Development for Dual-Use Solar and 1070 nm Laser Power Converters

Dual-use power converter cells can receive solar and laser power simultaneously to generate current, an application relevant to space and terrestrial industries. This study investigates two concepts of solar cells optimized for dual-use 1070 nm laser and solar power conversion, a single-junction and triple-junction cell. Because it is bandgap-tuned for a 1070 nm laser, the 1.1 eV junction is incorporated into each of the two designs, making its development key to the success of both concepts. Efficiency data for a one junction GaInAs cell demonstrates a laser conversion efficiency of 38% at 1070nm wavelength without an anti-reflection coating. However, the single-junction device requires optimization to reduce short wavelength absorption of the broad solar spectrum. In both devices, the graded buffer layers in the GaInAs cell affects the cell's performance by reducing threading dislocations in the active junction. However, the buffer in the three-junction device also acts as a lateral transport layer and so affects the fill factor depending on its sheet resistance. By varying the buffer thickness, we demonstrate a direct relationship between buffer thickness and sheet resistance reduction, while considering implications to open-circuit voltages. We also performed resistance modeling to determine the optimal grid spacing and thickness of the grid fingers to minimize losses due to sheet resistance and grid shading.

junctions↗
DOE OSTI2025

Laser Ablation for Low-Cost Multijunction III-V Solar Cell Mesa Isolations

Eliminating photolithography from solar cell processing is a significant opportunity for cost reduction for III-V solar cells. In this work, we test femtosecond laser ablation and scribing as an alternative to contact photolithography and wet chemical etching for mesa isolation, when processing multijunction cells. We demonstrate that upright multijunction solar cells isolated by using the laser as a scribe to cleave through the substrate had virtually no performance loss when compared to a baseline cell processed with photolithography. By contrast, cells isolated by laser ablating through the active layers have performance losses that cannot be fully eliminated with post-processing etches. This demonstration of photolithography-free mesa isolation with no performance losses is promising for less expensive III-V manufacturing.

14 SOLAR ENERGY↗