Search NASA⌕ Search

SEARCH · Search NASA

Results for “Centrifugal compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Design, development, and test of a laser velocimeter for high speed turbomachinery

The paper describes the design, development, and test of a laser Doppler velocimeter (LDV) to map the velocity fields in a small, high speed, 8:1 pressure ratio, 0.91 kg/s (2 lbm/s), centrifugal compressor. This instrument is being used as a diagnostic tool for the study of the basic fluid dynamics of the inducer, impeller and the diffuser regions of high pressure ratio, small, centrifugal compressors. The LDV instrumentation has been optimized to permit the measurement of instantaneous velocities up to approximately 500 m/s, measured in absolute coordinates, within a rotating compressor impeller. Velocities of the same magnitude can also be measured in the two-dimensional radial plane of the diffuser. It is shown that LDV can make nondisturbing gas velocity measurements and surmount the difficulties found in applying other types of aerodynamic instrumentation to this measurement problem.

Runstadler, P. W., Jr.↗
NASA NTRS1985

Active magnetic bearings for optimum turbomachinery design

The design and shop test results are given for a high speed eight stage centrifugal compressor supported by active magnetic bearings. A brief summary of the rotor dynamics analysis is presented with specific attention given to design considerations for optimum rotor stability. The concerns for retrofit of magnetic bearings in existing machinery are discussed with supporting analysis of a four stage centrifugal compressor. Recommendations are given on design and analysis requirements for successful machinery operation of either retrofit or new design turbomachinery.

Hustak, J.↗
NASA NTRS1993

Experimental and computational results from a large low-speed centrifugal impeller

An experimental and computational investigation of the NASA Low-Speed Centrifugal Compressor (LSCC) flow field has been conducted using laser anemometry and Dawes' 3D viscous code. The experimental configuration consists of a backswept impeller followed by a vaneless diffuser. Measurements of the three-dimensional velocity field were acquired at several measurement planes through the compressor. The measurements describe both the throughflow and secondary velocity field along each measurement plane and in several cases provide details of the flow within the blade boundary layers. The experimental and computational results provide a clear understanding of the development of the throughflow momentum wake which is characteristic of centrifugal compressors.

Hathaway, M. D.↗
NASA NTRS1994

Experimental and computational results from a large low-speed centrifugal impeller

An experimental and computational investigation of the NASA Low-Speed Centrifugal Compressor (LSCC) flow field was conducted using laser anemometry and Dawes' 3D viscous code. The experimental configuration consists of a back-swept impeller followed by a vaneless diffuser. Measurements of the three-dimensional velocity field were acquired at several measurement planes through the compressor. The measurements describe both the throughflow and secondary velocity field along each measurement plane and, in several cases, provide details of the flow within the blade boundary layers. The experimental and computational results provide a clear understanding of the development of the throughflow momentum wake which is characteristic of centrifugal compressors.

Hathaway, M. D.↗
NASA NTRS1991

Critical speeds and forced response solutions for active magnetic bearing turbomachinery, part 2

The need for better performance of turbomachinery with active magnetic bearings has necessitated a study of such systems for accurate prediction of their vibrational characteristics. A modification of existing transfer matrix methods for rotor analysis is presented to predict the response of rotor systems with active magnetic bearings. The position of the magnetic bearing sensors is taken into account and the effect of changing sensor position on the vibrational characteristics of the rotor system is studied. The modified algorithm is validated using a simpler Jeffcott model described previously. The effect of changing from a rotating unbalance excitation to a constant excitation in a single plane is also studied. A typical eight stage centrifugal compressor rotor is analyzed using the modified transfer matrix code. The results for a two mass Jeffcott model were presented previously. The results obtained by running this model with the transfer matrix method were compared with the results of the Jeffcott analysis for the purposes of verification. Also included are plots of amplitude versus frequency for the eight stage centrifugal compressor rotor. These plots demonstrate the significant influence that sensor location has on the amplitude and critical frequencies of the rotor system.

Rawal, D.↗
DOE OSTI2022

OPEN2018 (continuation of GENSETS effort)

This project has demonstrated the key components and engineering principles to support a residential scale (1 to 2 kWe) recuperated Brayton cycle generator based upon a screw compressor and screw expander. This technical work is a continuation of the previously awarded ‘GENSETS’ program. The product goal has been to achieve a 40% fuel-to-electric LHV efficiency, an 80% overall CHP efficiency, emissions qualified to the California Air Resources Board standards, and at noise levels of 55 dB or less at 1 meter. Further, the product must operate with 8,000 hour service intervals and achieve a mean-time to overhaul of 90,000 hours. Lastly, and possibly most importantly, the product must meet demanding cost targets, exhibiting a factory cost well below $1,500/kWe. After extensive aerodynamic studies under the ‘GENSETS’ program, Brayton concluded that miniature turbomachinery could not achieve an efficiency consistent with the product’s system performance goal. Given compressor and turbine efficiency targets in the range of 78 to 81%, Brayton turned to the rotary screw machines. While the justification for a screw compressor over a conventional centrifugal compressor is well supported by industry experience, the high temperature expander represented the core technology advancement. To meet the extremely high efficiency goals, an all-ceramic rotary screw expander hot section was developed and has now been tested in the laboratory. This first-of-its-kind ceramic screw expander prototype was able to demonstrate aerodynamic efficiency in line with predictions. The test article was successfully run to full stress conditions so has also validated the mechanical design of such a unit. This has opened new avenues for the commercialization of high efficiency, small scale power generation. Interest in the technology has sparked several requests for alternate uses, an invitation to present at a screw machine conference, and continued interest from parties looking to develop a product in the spirit of the original ‘GENSETS’ goals.

42 ENGINEERING↗
DOE OSTI2025

A Review of the Research and Development of Brayton Cycle Technology in Nuclear Power Applications with a Focus on Compressor Technology

This study reviews the integration of Brayton Cycle (BC) systems in nuclear power generation, emphasizing their potential to enhance thermal efficiency and operational flexibility over traditional Rankine Cycle (RC) systems. Key working fluids, such as helium (He), supercritical carbon dioxide (sCO 2 ), nitrogen (N 2 ), and air, are evaluated for their performance, efficiency, and compatibility with nuclear systems. He is recognized for its high thermal conductivity and inertness at elevated temperatures, while sCO 2 demonstrates advantages in compactness and efficiency in midrange temperatures. This article also highlights the importance of compressor designs in optimizing BC performance and reviews, available compressor technologies. Axial and centrifugal compressor designs enable efficient gas compression while managing the thermal and mechanical stresses associated with high-pressure operations in nuclear systems. Combined with variable geometry components and advanced materials, these technologies address the challenges posed by varying load conditions. Despite the promising features of BC systems, several challenges persist, including high leakage rates and material degradation under extreme conditions, which necessitate robust sealing technologies and thorough testing. The insights gained from operational experiences at facilities, such as the Oberhausen II plant and the High-Temperature He Test Facility (HHV), underscore the complexities involved in designing high-temperature gas turbines for nuclear applications. This review concludes that as the nuclear industry evolves, BC systems hold significant promise for contributing to a sustainable energy future, particularly in the context of small modular reactors (SMRs) and microreactors. Further exploration of combined cycle configurations that combine BCs with RCs may enhance overall efficiency and flexibility in power generation.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2011

Miniature high speed compressor having embedded permanent magnet motor

A high speed centrifugal compressor for compressing fluids includes a permanent magnet synchronous motor (PMSM) having a hollow shaft, the being supported on its ends by ball bearing supports. A permanent magnet core is embedded inside the shaft. A stator with a winding is located radially outward of the shaft. The PMSM includes a rotor including at least one impeller secured to the shaft or integrated with the shaft as a single piece. The rotor is a high rigidity rotor providing a bending mode speed of at least 100,000 RPM which advantageously permits implementation of relatively low-cost ball bearing supports.

Zhou, Lei↗
NASA NTRS2024

NASA HECC Geometry and Performance Review Part 1: Validation of a Computational Model for the Vaneless Diffuser Configuration with As-Manufactured Impeller Geometry

An investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. This multipart investigation presents an extensive validation of the computational model against experimental data. The validated model was then used to explore the effects geometric differences between the as-manufactured and design-intent impellers. Lastly, the validated model was used for comparison against an experimental tip clearance study. Part I of the investigation focused on describing the HECC vaneless computational model and its validation against the experimental data published in GT2023-103128. To generate the model, a verification of the manufactured impeller was performed and was confirmed to match the impeller CAD. Section data from the impeller CAD, referred to as the As-Manufactured geometry, were used for development of the computational model. Steady RANS simulations utilizing the Wilcox K-Omega 98 turbulence model and a multiblock structured mesh were used to conduct a mesh convergence study. The resultant mesh was then used for simulations at both design-speed and off-design speed conditions. The simulations compared well to data in both 1D and 2D terms for the major performance metrics of efficiency, total pressure rise, and total temperature rise. Based on the observed results the model was deemed validated and was used in the latter two parts of the multipart investigation.

centrifugal compressor↗
NASA NTRSDate not supplied

NASA HECC Geometry and Performance Review Part 2: Geometric Differences Between the as-Manufactured and Design-Intent Impeller Geometry and Their Effects on the Vaneless Diffuser Configuration Performance

An investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. This multipart investigation focused on validating the computational model against experimental data. The validated model was then used to explore the effects of observed geometric differences between the as-manufactured and design-intent impellers. Lastly, the validated model was used for comparison against an experimental tip clearance study. Details regarding each of the parts are detailed below: This second part of a multipart investigation of the NASA HECC vaneless diffuser configuration focused on the comparison of the as-manufactured HECC vaneless computational model validated in Part I against a new model that used the same grid and solver settings but replaced the impeller section data with the design-intent sections from NASA/CR-2014-218114/Rev1. The 1D performance values showed that the as-manufactured impeller underperformed compared to the design-intent for all four speedlines that were simulated. Further investigation of radial profiles, loading and contours showed consistent underperformance of the as-manufactured. An investigation into the source of the difference led to the discovery of several geometric differences in the two impellers of magnitudes that could not be explained outside of manufacturing. The differences that were observed can be summarized into four categories: fillets, TE exit radius differences, splitter LE differences and main blade thickness differences. The investigation then shifted to attempting to isolate the geometric differences as best as possible and to understand their contribution to the observed underperformance. The investigation showed that out of the four geometric differences that were explored, the differences in the splitter blade had the largest effect.

centrifugal compressor↗
NASA NTRS2024

NASA HECC Geometry and Performance Review Part 2: Geometric Differences Between the As-Manufactured and Design-Intent Impeller Geometry and their Effects on the Vaneless Diffuser Configuration Performance

An investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. This multipart investigation focused on validating the computational model against experimental data. The validated model was then used to explore the effects of observed geometric differences between the As-Manufactured and Design-Intent impellers. Lastly, the validated model was used for comparison against an experimental tip clearance study. Part II of the investigation of the NASA HECC vaneless diffuser configuration focused on understanding the differences in geometry and performance between the As-Manufactured impeller and the Design-Intent impeller. This was achieved through comparison of the As-Manufactured HECC vaneless computational model, developed from the solid model of the impeller and validated in Part I, against a new model developed from the Design-Intent blade sections published in NASA/CR-2014-218114/Rev1. The 1D performance values showed that the As-Manufactured impeller underperformed compared to the Design-Intent for all four speedlines that were simulated. Further investigation of profiles, loading and contours showed consistent underperformance of the As-Manufactured relative to the Design-Intent. An investigation into the source of the performance differences led to the discovery of several significant variations in the impeller geometries. The differences that were observed can be summarized into four categories: fillets, trailing-edge exit radii variation, dissimilarity in the splitter leading-edge geometry and main blade thickness differences. The investigation then shifted its effort to quantify the performance effects caused by geometric differences. The investigation showed that out of the four geometric differences that were explored, the differences in the splitter blade had the largest impact. These differences most notably changed flow physics near the splitter leading edge, especially near the tip of the impeller.

centrifugal compressor↗
NASA NTRS1984

Internal hysteresis experienced on a high pressure syn gas compressor

A vibration instability phenomenon experienced in operating high pressure syn gas centrifugal compressors in two ammonia plants is described. The compressors were monitored by orbit and spectrum analysis for changes from baseline readings. It is found that internal hysteresis was the major destabilizing force; however, the problem was further complicated by seal lockup at the suction end of the compressor. A coupling lockup problem and a coupling fit problem, which frettage of the shaft, are also considered as contributors to the self excited vibrations.

Zeidan, F. Y.↗
NASA NTRS1975

A compressor designed for the energy research and development agency automotive gas turbine program

A centrifugal compressor was designed for a gas turbine powered automobile as part of the Energy Research and Development Agency program to demonstrate emissions characteristics that meet 1978 standards with fuel economy and acceleration which are competitive with conventionally powered vehicles. A backswept impeller was designed for the compressor in order to attain the efficiency goal range required for the objectives of this program. Details of the design and method of flow analysis of the compressor are presented.

Galvas, M. R.↗
NASA NTRS1973

Small, high pressure ratio compressor: Aerodynamic and mechanical design

The Small, High-Pressure-Ratio Compressor Program was directed toward the analysis, design, and fabrication of a centrifugal compressor providing a 6:1 pressure ratio and an airflow rate of 2.0 pounds per second. The program consists of preliminary design, detailed areodynamic design, mechanical design, and mechanical acceptance tests. The preliminary design evaluate radial- and backward-curved blades, tandem bladed impellers, impeller-and diffuser-passage boundary-layer control, and vane, pipe, and multiple-stage diffusers. Based on this evaluation, a configuration was selected for detailed aerodynamic and mechanical design. Mechanical acceptance test was performed to demonstrate that mechanical design objectives of the research package were met.

Bryce, C. A.↗
DOE OSTI2021

Radial Compressor Design and Off-Design for Trans-critical CO2 Operating Conditions

A multi-staged intercooled centrifugal compressor design is performed for an indirect-fired sCO2 cycle and the design point data are used to generate the performance maps using a 2D mean-line analysis code. Fluid and turbomachinery similarity laws are applied to find an appropriate surrogate ideal gas fluid to be used in the design and performance map generation codes. The performance maps are then scaled back for the sCO2 fluid case using the affinity laws. The developed methodology is validated using the experimental data for a compressor operating at similar inflow conditions.

Uysal, Selcuk Can↗
NASA NTRS1948

Performance of Compressor of XJ-41-V Turbojet Engine V-Performance Analysis of Compressor with Revised Vaned Collector over Range of Compressor Speeds from 3600 to 11,500 RPM

An investigation of the XJ-41-V turbojet-engine compressor with a revised vaned collector was conducted to determine the performance of the compressor and to obtain fundamental information on the aerodynamic problems associated with large centrifugal compressors of this type. The original vaned collector was revised by increasing the flow area at the vaned collector entrance. A maximum adiabatic efficiency of 0.81 was obtained et a corrected weight flow of 36.5 pounds per second and a pressure ratio of 1.90. The peak pressure ratio was 3.93 and occurred at an impeller speed of 11,500 rpm at a corrected weight flow of 65.5 pounds per second. Revision of the vaned collector resulted in an increased airflow capacity over the speed range. The design air-flow capacity of 78 pounds per second was very nearly reached at the engine design speed of 11,500 rpm. The compressor air-flow choking point occurred in the vaned collector passage; however, at speeds above 8300 rpm, the air-flow capacity of the impeller was being approached as indicated by large pressure losses in the impeller at maximum air-flow conditions. An increase in compressor air-flow capacity at the higher speeds can possibly be obtained 5y removal of the flow restriction in the impeller, which would result in an increased air density at the vaned collector entrance.

Ginsburg, Ambrose↗