Search NASA⌕ Search

SEARCH · Search NASA

Results for “Concentration of measure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fatigue Testing and Characterization of Pre-hydrided Zircaloy-4 Cladding Tubes

The solubility of hydrogen in Zircaloy-4 (Zry-4) at the cladding operating temperature is near 100 wt. ppm. Above this solubility limit, excess hydrogen precipitates as δ-hydride platelets in the cladding material. Because of the effect of the thermal gradient across the cladding thickness on the migration and precipitation of hydrogen, hydride rims are often observed at the cladding outer surface; under excessive corrosion conditions hydride blisters are possible. It is well known that the fatigue of metal alloys, especially high cycle fatigue, is sensitive to the status of surface including the microstructure, roughness, and residual stress. Thus, the question considered herein, is whether excessive hydrogen pickup modifies the microstructure such that it has a degradation effect on the fatigue performance of cladding during operation. This report describes the evaluation of fatigue performance of a pre-hydrided Zry-4 cladding. A commercial Zry-4 was polished and pre-hydrided to 800 ppm and 1300 ppm H contents. The fatigue testing was conducted under strain control at 5 Hz with fully-reversed bending by using a cyclic integrated reversible bending fatigue tester (CIRFT). Six specimens with 1300 ppm and one specimen with 800 ppm were tested. Significant variation in test results were observed. While two of the 1300 ppm specimens failed with less than 1 ×10 5 cycles (at 0.32% and 0.41%), the four other samples did not fail over the strain amplitude range of 0.25% to 0.38%. Interestingly, the fracture initiation site of the failed samples was on the outside diameter (OD) surface rather than on the inside diameter (ID) surface as is typical for the as-polished cladding. This suggested a degrading effect of the hydriding process. Subsequently, three of the unfailed specimens were then further tested at ~0.43% to observe where failure initiation occurred. Significant variation was also observed in these three specimens. One specimen failed at ~9000 cycles while the two others failed at 43000 and 1.06 ×10 5 cycles. The performance here correlated to the location of failure initiation; failure initiated on the OD in the sample that failed after 9000 cycles while it initiated on the ID in the sample that failed after 43000 and 1.06 ×10 5 cycles. Flat features at the OD initiation sites suggest a brittle hydride feature on the surface of those samples was the cause of the degradation in fatigue performance, though the overall hydrogen levels in all samples was similar. A summary of all the observations is provided below: • The un-failed specimens with 1300 ppm H were cycled to failure with a higher amplitude near 0.43%. In addition, the fatigue-treated specimen tended to have a longer fatigue at the same induced amplitude. • Fractography revealed a mixed failure mode for the pre-hydrided specimen. Particularly, the specimen with fracture initiation site (FIS) located on the outer diameter surface of tube tended to have a shorter fatigue life than that of FIS on the inner diameter surface. • Etched cross section was shown to have hydride platelets aligned with tube longitudinal axis as expected, and the density of hydrides is at the similar level as in literature data. Meanwhile, a LECO procedure was applied for hydrogen concentration measurement, which showed the measured hydrogen contents are close to the nominal value. • With the polished cladding tube as baseline, O’Donnell-Lager (O-L) analysis showed that a decrease of about 50% in reduction-of-area (RA) would be needed for the O-L fitting to the fatigue data of 1300 ppm cladding. The suggestion for the next steps is provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Liquid Hydrogen Pooling and Vaporization Experiments

A comprehensive investigation into the pooling and vaporization of liquid hydrogen spills onto concrete and steel surfaces in a steady cross-wind is presented in this work. This is the first instance of liquid hydrogen pooling and dispersion in a steady environment. A high-capacity fan in a large tunnel was used to generate the steady cross-winds while spilling roughly 10-20, or 40 l/min of liquid hydrogen onto substrates. Temperature and extractive concentration measurements were made, in addition to visible and infrared imaging, to understand development of the pool and down-wind dispersion of the vaporized hydrogen. Overall, the results enhance the understanding of liquid hydrogen pooling and dispersion dynamics and provide critical data for validating models of pooling and vapor dispersion under various conditions.

08 HYDROGEN↗
DOE OSTI2023

Estimating Vadose Zone Flow Properties at the 100 K-East Soil Flushing Site Using ERT Monitoring Data: 2023 Interim Report - 100 KE Soil Property Estimation

In situ soil flushing is being using at the Hanford 100 K-East (100 KE) area to transport mobile chromium contamination in the vadose zone to the water table, where it can be collected and treat through pump and treat operations. The efficacy of soil flushing is directly related to the volume of clean water that infiltrates through contaminated soils. In practice, it is infeasible to comprehensively monitor which regions of the vadose zone are being infiltrated through direct sampling of pore water. Consequently, there can be significant uncertainty about which regions of the subsurface have been treated, especially if hydrogeologic conditions are favorable for the development of unstable flows and preferred flow pathways through the vadose zone (Jarvis, Koestel, and Larsbo 2016). Current approaches for quantitative monitoring of soil flushing performance rely on contaminant concentration measurements collected from extractions wells. There is no quantitative information on the volume of flush water delivered to targeted regions of the vadose zone at the Hanford Site, leading to significant uncertainty regarding source term removal and long-term impacts to groundwater. If the subsurface hydrogeologic properties at the 100 KE Area were adequately known, qualitative metrics of soil flushing performance could be simulated, thereby negating expenses required to obtain quantitative performance information through borehole drilling/sampling. However, estimating in situ hydrogeologic properties has long proven elusive, due primarily to a lack of sufficient information to constrain heterogeneous property estimates to a useful degree of certainty. Estimating vadose zone hydrogeologic properties is particularly challenging due the dependence of hydraulic conductivity on saturation. This report describes progress toward a first-of-its-kind demonstration using surface time-lapse 3D electrical resistivity tomography (ERT) monitoring data to estimate the hydrogeologic properties that control flush water transport at the 100 KE soil flushing site. The ultimate objective is (1) to verify sufficient information exists in the ERT monitoring data to adequately resolve vadose zone hydraulic properties, and (2) generate a “digital twin” (i.e., a numerical simulator) that can be used to simulate the amount of flush water that has been delivered to each targeted region of the vadose zone, and thereby assess the efficacy of flush water delivery. Resulting performance estimates can be used in leu of comprehensive borehole drilling and direct sampling (or wellbore logging) that would otherwise be required to obtain the same information.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Mapping the performance of a versatile water-based condensation particle counter (vWCPC) with numerical simulation and experimental study

Accurate airborne aerosol instrumentation is required to determine the spatial distribution of ambient aerosol particles, particularly when dealing with the complex vertical profiles and horizontal variations of atmospheric aerosols. A versatile water-based condensation particle counter (vWCPC) has been developed to provide aerosol concentration measurements under various environments with the advantage of reducing the health and safety concerns associated with using butanol or other chemicals as the working fluid. However, the airborne deployment of vWCPCs is relatively limited due to the lack of characterization of vWCPC performance at reduced pressures. Given the complex combinations of operating parameters in vWCPCs, modeling studies have advantages in mapping vWCPC performance. In this work, we thoroughly investigated the performance of a laminar-flow vWCPC using COMSOL Multiphysics® simulation coupled with MATLAB™. We compared it against a modified vWCPC (vWCPC model 3789, TSI, Shoreview, MN, USA). Our simulation determined the performance of particle activation and droplet growth in the vWCPC growth tube, including the supersaturation, $D$ p,kel,0 (smallest size of particle that can be activated), $D$ p,kel,50 (particle size activated with 50 % efficiency) profile, and final growth particle size D d under wide operating temperatures, inlet pressures $P$ (30–101 kPa), and growth tube geometry (diameter $D$ and initiator length $L$ ini ). The effect of inlet pressure and conditioner temperature on vWCPC 3789 performance was also examined and compared with laboratory experiments. The COMSOL simulation result showed that increasing the temperature difference (Δ$T$) between conditioner temperature $T$ con and initiator $T$ ini will reduce $D$ p,kel,0 and the cut-off size $D$ p,kel,50 of the vWCPC. In addition, lowering the temperature midpoint ($T$ mid = $\frac{T_{con}+T_{ini}}{2}$ increases the supersaturation and slightly decreases the $D$ p,kel . The droplet size at the end of the growth tube is not significantly dependent on raising or lowering the temperature midpoint but significantly decreases at reduced inlet pressure, which indirectly alters the vWCPC empirical cut-off size. Our study shows that the current simulated growth tube geometry ($D$=6.3 mm and $L$ ini =30 mm) is an optimized choice for current vWCPC flow and temperature settings. The current simulation can more realistically represent the $D$ p,kel for 7 nm vWCPC and also achieved good agreement with the 2 nm setting. Using the new simulation approach, we provide an optimized operation setting for the 7 nm setting. This study will guide further vWCPC performance optimization for applications requiring precise particle detection and atmospheric aerosol monitoring.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Comparison of basin-scale in situ and meteoric 10 Be erosion and denudation rates in felsic lithologies across an elevation gradient at the George River, northeast Tasmania, Australia

Long-term erosion rates in Tasmania, at the south ern end of Australia’s Great Dividing Range, are poorly known; yet, this knowledge is critical for making informed land-use decisions and improving the ecological health of coastal ecosystems. Here, we present quantitative, geologically relevant estimates of erosion rates for the George River basin, in northeast Tasmania, based on in situ-produced 10 Be ( 10 Be i ) measured from stream sand at two trunk channel sites and seven tributaries (mean: 24.1 ± 1.4 Mg km -2 yr -1 ; 1σ). These new 10 Bei-based erosion rates are strongly related to elevation, which appears to control mean annual precipitation and temperature, suggesting that elevation-dependent surface processes influence rates of erosion in northeast Tas mania. Erosion rates are not correlated with slope in contrast to erosion rates along the mainland portions of Australia’s Great Dividing Range. We also extracted and measured meteoric 10 Be ( 10 Be m ) from grain coatings of sand-sized stream sediment at each site, which we normalize to measured concentrations of reactive 9 Be and use to estimate 10 Be m -based denudation rates for the George River. 10 Bem/ 9 Be reac denudation rates replicate 10 Be i erosion rates within a factor of 3 but are highly sensitive to the value of 9 Be that is found in bedrock ( 9 Be parent ), which was unmeasured in this study. 10 Bem/ 9 Be reac denudation rates seem sensitive to recent mining, forestry, and agricultural land use, all of which resulted in widespread topsoil disturbance. Our findings suggest that 10 Bem/ 9 Be reac denudation metrics will be most useful in drainage basins that are geologically homogeneous, where recent disturbances to topsoil profiles are minimal, and where 9 Be parent is well constrained.

58 GEOSCIENCES↗
DOE OSTI2023

A geospatial risk analysis graphical user interface for identifying hazardous chemical emission sources

Background: Performing back trajectory and forward trajectory using the Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) is a reliable approach for assessing particle transport after release among mid-field atmospheric models. HYSPLIT has an externally facing online interface that allows non-expert users to run the model trajectories without requiring extensive training or programming. However, the existing HYSPLIT interface is limited if simulations have a large amount of meteorological data and timesteps that are not coincident. The objective of this study is to design and develop a more robust tool to rapidly evaluate hazard transport conditions and to perform risk analysis, while still maintaining an intuitive and user-friendly interface. Methods: HYSPLIT calculates forward and backward trajectories of particles based on wind speed, wind direction, and the corresponding location, timestamp, and Pasquill stability classes of the regions of the atmosphere in terms of the wind speed, the amount of solar radiation, and the fractional cloud cover. The computed particle transport trajectories, combined with the online Proton Transfer Reaction-Mass Spectrometry (PTR-MS) data (https://figshare.com/articles/dataset/ARL_Data_from_PROS_station_at_Hanford_site/19993964), can be used to identify and quantify the sources and affected area of the hazardous chemicals’ emission using the potential source distribution function (PSDF). PSDF is an improved statistical function based on the well-known potential source contribution function (PSCF) in establishing the air pollutant source and receptor relationship. Performing this analysis requires a range of meteorological and pollutant concentration measurements to be statistically meaningful. The existing HYSPLIT graphical user interface (GUI) does not easily permit computations of trajectories of a dataset of meteorological data in high temporal frequency. To improve the performance of HYSPLIT computations from a large dataset and enhance risk analysis of the accidental release of material at risk, a geospatial risk analysis tool (GRAT-GUI) is created to allow large data sets to be processed instantaneously and to provide ease of visualization. Results: The GRAT-GUI is a native desktop-based application and can be run in any Windows 10 system without any internet access requirements, thus providing a secure way to process large meteorological datasets even on a standalone computer. GRAT-GUI has features to import, integrate, and convert meteorological data with various formats for hazardous chemical emission source identification and risk analysis as a self-explanatory user interface. The tool is available at https://figshare.com/articles/software/GRAT/19426742.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

INVESTIGATION OF TURBULENT JETS, SPRAYS, AND SUPERCRITICAL MIXING BY TIME RESOLVED RAINBOW SCHLIEREN DEFLECTOMETRY

As technological advancements have enabled higher efficiency compression ignition (CI) engines (diesel engines) by operating at higher pressures and temperatures, the mechanisms of fuel-air mixing are postulated to change. Thus, there is a greater need for experimental data to develop and verify new phenomena. However, the fast time scales and harsh environments associated with CI engines present many experimental difficulties and requires high quality non-intrusive diagnostics to obtain useful data. The diagnostics itself must be validated prior to its implementation in an engine environment. The purpose of this research is to advance rainbow schlieren deflectometry (RSD) to study turbulent fuel sprays including the effects of supercritical mixing in CI engine environments. This objective is met by developing and applying quantitative RSD, for the first time, to three separate aspects of fuel sprays: 1) turbulent mixing, 2) phase boundaries, and 3) non-ideal gas mixing. First, quantitative RSD is demonstrated for turbulent mixing in a canonical helium jet. Rayleigh scattering data in the literature is used to validate the concentration measurements obtained by RSD. The results also provide explanations for phenomena occurring in the helium jet and provide data not yet present in the literature. Second, RSD is applied to high pressure multi-phase fuel sprays and new methodologies are developed to distinguish the liquid region from the vapor region and to quantify the in-between region on a probabilistic basis. Isolating liquid and vapor regions generally requires two separate diagnostics, e.g., Mie scattering (liquid region) and Rayleigh scattering (vapor region). However, the results of this study demonstrate that RSD can be used as a single diagnostic to measure both liquid and vapor boundaries. Third, the optical-to-thermodynamic relations associated with refrac-tometry are investigated under non-ideal gas mixing conditions to develop a generalized relationship valid for both ideal or non-ideal gas mixing. The last part of this research develops the theoretical tools to understand and experimentally realize supercritical mixing at diesel conditions. Guided by the theoretical analysis, RSD is applied to compare supercritical versus transcritical mixing at CI conditions using a constant pressure test rig. It is found that while fully supercritical mixing ers benefits in diesel engines, i.e, faster mixing times (50% higher velocities), the absence of droplets which cause high levels of particulate emissions, etc., it would be difficult to achieve in practice because of the requirements of fuels with low critical temperature and/or substantial fuel preheating.

02 PETROLEUM↗
DOE OSTI2021

Multielectrode sensor for concentration and depth measurements in molten salt

A multi electrode sensor that provides in-situ, real time measurements for molten salts and other process fluids such as real-time concentration and salt level measurements for nuclear systems such as molten salt reactors, nuclear reprocessing facilities utilizing molten salts and concentrated solar power systems. The sensor has multiple electrodes with unique lengths which are connected to a potentiostat. Measurements are taken when the electrodes are immersed in the process fluid.

Hoyt, Nathaniel C.↗
DOE OSTI2020

Ship-based measurements of ice nuclei concentrations over the Arctic, Atlantic, Pacific and Southern oceans

Ambient concentrations of ice-forming particles measured during ship expeditions are collected and summarised with the aim of determining the spatial distribution and variability in ice nuclei in oceanic regions. The presented data from literature and previously unpublished data from over 23 months of ship-based measurements stretch from the Arctic to the Southern Ocean and include a circumnavigation of Antarctica. In comparison to continental observations, ship-based measurements of ambient ice nuclei show 1 to 2 orders of magnitude lower mean concentrations. To quantify the geographical variability in oceanic areas, the concentration range of potential ice nuclei in different climate zones is analysed by meridionally dividing the expedition tracks into tropical, temperate and polar climate zones. We find that concentrations of ice nuclei in these meridional zones follow temperature spectra with similar slopes but vary in absolute concentration. Typically, the frequency with which specific concentrations of ice nuclei are observed at a certain temperature follows a log-normal distribution. A consequence of the log-normal distribution is that the mean concentration is higher than the most frequently measured concentration. Finally, the potential contribution of ship exhaust to the measured ice nuclei concentration on board research vessels is analysed as function of temperature. We find a sharp onset of the influence at approximately -36 °C but none at warmer temperatures that could bias ship-based measurements.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Quantitative Voltammetry Measurements of High-Concentration Actinides in Molten Chloride Fuel Salts

Molten chloride mixtures containing high concentrations of UCl 3 (i.e., >70 wt%) are candidates for next-generation molten salt reactor (MSR) fuel salts that enable new plant optimization and fuel cycle strategies. MSR licensing, however, is contingent on the development of effective material control and accounting (MC&A) practices for these salts. To close this gap, we have developed an electroanalytical approach that enables accurate in situ measurements of uranium concentrations in these highly loaded fuel salts. This methodology uses a multielectrode array voltammetry sensor combined with digital simulations that account for non-idealities such as uncompensated resistance effects. The theory-based numerical simulations of voltammetry responses yielded correction factors that are agnostic of electrochemical cell geometry and produced consistent voltammetry peak current results when correcting for varying amounts of ohmic resistance. In doing so, we have demonstrated accurate concentration measurements for UCl 3 in LiCl-KCl-UCl 3 across a range of mass fractions between 55 and 72.3 wt% at 550 °C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Exploring the use of thorium isotope compositions and concentrations as nuclear forensic signatures for uranium ore concentrates

This interlaboratory study measured thorium concentrations and isotope compositions in uranium ore concentrates from different geographical locations to examine whether thorium impurities may be useful forensic signatures for uranium ore concentrates found out of regulatory control. Measured 230 Th/ 232 Th in fifteen uranium ore concentrates record over three orders of magnitude of compositional variation. Results demonstrate that 230 Th/ 232 Th used in combination with U/Th ratios resulted in a unique signature for individual uranium ore concentrates from different processing locations. Data presented here suggest potential for 230 Th/ 232 Th and U/Th to be used as comparative signatures to investigate the provenance of seized uranium ore concentrates.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Optimization of the compositions of polyanionic sodium-ion battery cathode NaFe 2-x V x (PO 4 )(SO 4 ) 2

Sodium (Na) super ionic conductor (NASICON) polyanionic compounds have recently attracted much attention from the battery community because of their electroactive properties and reasonably high ionic conductivities, leading to their use as a cathode in sodium-ion batteries. This article describes the compositional optimizations, crystallographic evaluations, and electrochemical behavior of a new mixed NASICON polyanionic compound, NaFe 2-x V x (PO 4 )(SO 4 ) 2 . By doping the characteristic Fe 3+ sites of the FeO 6 octahedrons with varying amounts of V 3+ , the electrochemical stability and charge transport in NaFe 2 (PO 4 )(SO 4 ) 2 were enhanced. The resulting best composition, with crystal structure NaFe 1.4 V 0.6 (PO 4 )(SO 4 ) 2 resolved through the Rietveld method, exhibited a stable capacity compared with the other synthesized compositions. In situ powder x-ray diffraction measurements, a single-phase intercalation/deintercalation mechanism of the NASICON structure in the measured sodium concentration window was observed with no impurity phase formation. Further electrochemical assessments revealed the interfacial charge transfer kinetics to be the rate-limiting step in the sodium concentration window. Also, the measured sodium-ion diffusivity values in the range of 6 × 10 -11 to 7 × 10 -11 cm 2 /s in the measured sodium concentration range. The results reported here highlight the potential of compositionally and morphologically optimized NaFe 1.4 V 0.6 (PO 4 )(SO 4 ) 2 with higher particle surface areas as a cathode material for high-performance sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Method for Real-Time Salt Aerosol Concentration and Size Measurements for Molten Salt Reactor Safety Assessments

Licensing a new nuclear reactor involves evaluating credible accident scenarios by developing models that simulate accident progression to predict possible outcomes and their impact on safety. The formation of radionuclide-bearing aerosols in the respirable size range can significantly affect dose consequence and threaten human health and is therefore a focus of nuclear reactor safety assessments. Recent reviews of the literature identified a lack of existing experimental data describing the mechanisms of formation and properties (size, concentration, and composition) of radionuclide-bearing aerosols that may be produced from molten salt reactor (MSR) facilities during postulated accident scenarios. Experiments on aerosol formation from molten salt systems are a high priority need that will support MSR licensing by indicating the radiological consequences of aerosol formation and providing the data required for model development and validation. The evolving conditions that occur during a MSR accident, such as a spill of molten fuel salt, may affect aerosol formation mechanisms and aerosol properties over time. There is a need to conduct experiments that simulate credible MSR accidents in a laboratory to generate aerosols with realistic characteristics and behaviors and a need to measure these aerosols in real time under accident-relevant conditions. This report describes the development of a method that can be used to quantify the size and concentration of salt aerosol particles that form from molten salt systems in real time. This method will be employed in future integral effects tests that are conducted at an engineering scale to simulate realistic MSR accidents and in future separate effects tests that will provide mechanistic insight into aerosol formation and properties to support process model development.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Chemically distinct regions of Venus’s atmosphere revealed by measured N 2 concentrations

A defining characteristic of the planet Venus is its thick, CO 2 -dominated atmosphere. Despite over 50 years of robotic exploration of Venus, including thirteen successful atmospheric probes and landers, our knowledge of N 2 , the second most abundant compound in the atmosphere, is highly uncertain. We report the first measurement of the nitrogen content of Venus’s atmosphere at altitudes between 60 and 100 km. Our result, 5.0 ± 0.4 v% N 2 , is 40% higher than the value of 3.5 v% N 2 reported for the lower atmosphere (<50 km altitude). Our discovery of altitude-dependent variations in the N 2 content of the atmosphere defies early expectations of homogeneous composition below 100 km (for example, see ref. 1), and necessitates complete chemical modelling to investigate chemical versus physical explanations for the enhanced N 2 in the upper atmosphere. Furthermore, the existence of chemically distinct lower and upper atmosphere regions complicates the use of remote sensing measurements of the upper atmosphere to infer the properties of the lower atmosphere and surface, an important lesson that also extends to the growing field of exoplanet astronomy.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Improving Long-term Monitoring of Contaminated Groundwater at Sites where Attenuation-based Remedies are Deployed

This study presents an effective approach to tackle the challenge of long-term monitoring of contaminated groundwater sites where remediation leaves residual contamination in the subsurface. Traditional long-term monitoring of contaminated groundwater sites focuses on measuring contaminant concentrations and is applicable to sites where contaminant mass is removed or degraded to a level below the regulatory standard. The traditional approach is less effective at sites where risk from metals or radionuclides continues to exist in the subsurface after remedial goals are achieved. We propose a long-term monitoring strategy for this type of waste site that focuses on measuring the hydrological and geochemical parameters that control attenuation or remobilization of contaminants while de-emphasizing contaminant-concentration measurements. Furthermore, we demonstrate how this approach would be more effective than traditional long-term monitoring, using a site in South Carolina, USA, where groundwater is contaminated by several radionuclides. A comprehensive enhanced attenuation remedy has been implemented at the site to minimize discharge of contamination to surface water. The immobilization of contaminants occurs in three locations by manipulation of hydrological and geochemical parameters, as well as by natural attenuation processes. Deployment of our proposed long-term monitoring strategy will combine subsurface and surface measurements using spectroscopic tools, geophysical tools, and sensors to monitor the parameters controlling contaminant attenuation. The advantage of this approach is that it will detect the potential for contaminant remobilization from engineered and natural attenuation zones, allowing potential adverse changes to be mitigated before contaminant attenuation is reversed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗