Search NASA⌕ Search

SEARCH · Search NASA

Results for “Continuous manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Analysis of Pull Force Test Results for Crimped Connections

Crimped electrical contacts are reliable when strict process controls are followed during manufacturing and accompanied by continuous process verification through pull force testing. Cable and wire harness assemblies’ standards are developed and refined over time to provide the minimum pull force that a crimp contact must meet before it breaks from the wire. However, in practice the failures occur at a much higher tensile strength than the minimum required. The first section of this paper reviewed 780 pull force test results provided by NASA Centers that were collected and analyzed to determine how the data compare to NASA’s pre-existing requirements from the cable/harness standards NASA-STD-8739.4 and IPC/WHMA-A-620B-S. The measured tensile strength of most of the contact/conductor pairs (i.e., Contact/Wires or C/W) exceeded the minimum pull force values of NASA-STD-8739.4 and IPC/WHMA-A-620 standards by at least 100%. The C/W pair samples’ tensile strength values followed a normal distribution with an average tensile strength value that was at least 182% of the minimum requirement, and all the samples analyzed passed the pull force testing. In addition, the 95% confidence interval of the average tensile strength distributions for several C/W pairs was determined and plotted as error bars to show that the C/W pairs will meet and surpass the requirements. The frequency of pull force testing can be problematic for projects because of the cost and availability of spare contacts for the destructive test. It is possible to reduce the frequency of pull force testing if at the beginning of the production run, the conditions of the crimp tool and materials are verified, and the settings of the tool remain unchanged throughout the process. However, the project needs to understand and evaluate the impact to risk from reducing the frequency of testing prior to implementing process changes.

Alejandra Constante↗
NASA NTRSDate not supplied

Analysis of Pull Force Test Results for Crimped Connections

Crimped electrical contacts are reliable when strict process controls are followed during manufacturing and accompanied by continuous process verification through pull force testing. Cable and wire harness assemblies’ standards are developed and refined over time to provide the minimum pull force that a crimp contact must meet before it breaks from the wire. However, in practice the failures occur at a much higher tensile strength than the minimum required. The first section of this paper reviewed 780 pull force test results provided by NASA Centers were collected and analyzed to determine how the data compares to NASA’s pre-existing requirements from the cable/harness standards NASA-STD-8739.4 and IPC/WHMA-A-620B-S. The measured tensile strength of most of the contact/conductor pairs (i.e. Contact/Wires or C/W) exceeded the minimum pull force values of NASA-STD-8739.4 and IPC/WHMA-A-620 standards by at least 100 %. The tensile strength samples of the C/W pairs values followed a normal distribution with an average tensile strength value that was at least 182 % of the minimum requirement, and all the samples analyzed passed the pull force testing. In addition, the 95 % confidence interval of the average tensile strength distributions for several C/W pairs was determined and plotted as error bars to show that there is good likelihood to observe C/W pair normal distribution with a 95 % confidence interval that will meet and surpass the standard requirements. The frequency of pull force testing can be problematic for projects because of the cost and availability of spare contacts for the destructive test. It could be possible to reduce the frequency of pull force testing if at the beginning of the production run, the conditions of the crimp tool and materials are verified, and the settings of the tool remain unchanged throughout the process. However, the project must evaluate the impact to risk from reducing the frequency of testing.

Crimped connections↗
DOE OSTI2022

Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps – Phase 2

As the wind turbine industry continues to develop, the technology surrounding the design, development, and manufacturing of blades requires advancement as well. Wind turbine blades continue to increase in size, increasing the cost and time associated with manufacturing. Simulation driven manufacturing cycle design is required for the industry to maintain manufacturing schedules and optimize the manufacturing process. A recent effort to reduce the cycle time of wind blade spar caps encountered a recurring manufacturing defect during the exotherm and curing of the resin system after filling in the vacuum-assisted resin transfer molding (VARTM) process. Thermal waves developed in sections of the spar cap resulting in unacceptable part tolerances, requiring the parts to be thrown out. The first phase of this IACMI project focused on characterizing the fabric and epoxy system used in manufacturing and simulating the manufacturing process to determine the root cause of the thermal waves. The second phase of this project refined and validated the manufacturing simulations. The simulation workflow was then used to analyze multiple cure cycle options to determine if the thermal waves would appear. The estimated filling time from the filling simulation was shown to match well to experiment, and the temperature history from the curing simulation lined up well with experiment. This indicates that these simulations could be used to evaluate future curing cycles to be used with manufacturing. It is recommended that the distortion simulation work be completed for this project, as it would allow for further manufacturing cycle evaluation through the prediction of stresses and strains in the part. This could provide indicators of defects like the thermal waves seen in manufacturing earlier.

17 WIND ENERGY↗
DOE OSTI2021

Bioinspired energy absorbing material designs using additive manufacturing

Nature provides many biological materials and structures with exceptional energy absorption capabilities. Few, relatively simple molecular building blocks (e.g., calcium carbonate), which have unremarkable intrinsic mechanical properties individually, are used to produce biopolymer-bioceramic composites with unique hierarchical architectures, thus producing biomaterial-architectures with extraordinary mechanical properties. Several biomaterials have inspired the design and manufacture of novel material architectures to address various engineering problems requiring high energy absorption capabilities. For example, the microarchitecture of seashell nacre has inspired multi-material 3D printed architectures that outperform the energy absorption capabilities of monolithic materials. Using the hierarchical architectural features of biological materials, iterative design approaches using simulation and experimentation are advancing the field of bioinspired material design. However, bioinspired architectures are still challenging to manufacture because of the size scale and architectural hierarchical complexity. Notwithstanding, additive manufacturing technologies are advancing rapidly, continually providing researchers improved abilities to fabricate sophisticated bioinspired, hierarchical designs using multiple materials. This review describes the use of additive manufacturing for producing innovative synthetic materials specifically for energy absorption applications inspired by nacre, conch shell, shrimp shell, horns, hooves, and beetle wings. Potential applications include athletic prosthetics, protective head gear, and automobile crush zones.

36 MATERIALS SCIENCE↗
NASA NTRS2026

Smart Process Planning for Automated Fiber Placement

Many industries, including aerospace, automotive, wind energy, maritime, and sporting goods, rely on strong, lightweight materials called composites. These materials are made by layering fibers, which can come in the form of narrow strips or wider sheets, and setting them in a polymer matrix. One of the most advanced ways to make these parts is through automated fiber placement, where a machine lays down the fibers in precise patterns. This method can create very efficient and strong designs, but it is complex, expensive, and often depends heavily on the experience of skilled engineers. Today, the design, manufacturing, and inspection stages of composite production are usually handled separately. This separation means that important information, such as how a part will be built or what defects might occur, is not always shared between stages. As a result, parts may not be as lightweight, strong, or defect-free as possible, and the process can take longer and cost more. This research develops a smart process planning system that connects design, manufacturing, and inspection into one continuous process. Built as software that works with existing tools, the system can automatically plan how the fibers are placed, predicting and reducing defects while improving both manufacturability and strength. The system optimizes not only individual layers but also how defects are distributed across all layers, preventing them from stacking up in ways that weaken the final part. It also uses inspection results from completed parts to improve future designs, creating a feedback loop where each stage informs the others. The system was tested by designing a composite panel using this new approach and comparing it to a panel made with state-of-the-art manual planning methods. The results showed that the system could intentionally control where defects appeared and increase the efficiency of the planning process. By unifying design, manufacturing, and inspection, this research shows a way to make advanced composite manufacturing more efficient, consistent, and cost-effective. This approach lowers the barrier to using automated fiber placement and opens the door for its wider adoption not only in aerospace but also in industries such as automotive, wind energy, maritime, and sporting goods, where strong and lightweight structures are essential.

Computer-Aided Process Planning↗
NASA NTRS2004

STS Derived Exploration Launch Operations

A key aspect of the new space exploration programs will be the approach to optimize launch operations. A STS Derived Launch Vehicle (SDLV) Program can provide a cost effective, low risk, and logical step to launch all of the elements of the exploration program. Many benefits can be gained by utilizing the synergy of a common launch site as an exploration spaceport as well as evolving the resources of the current Space Shuttle Program (SSP) to meet the challenges of the Vision for Space Exploration. In particular, the launch operation resources of the SSP can be transitioned to the exploration program and combined with the operations efficiencies of unmanned EELVs to obtain the best of both worlds, resulting in lean launch operations for crew and cargo missions of the exploration program. The SDLV Program would then not only capture the extensive human space flight launch operations knowledge, but also provide for the safe fly-out of the SSP through continuity of system critical skills, manufacturing infrastructure, and ability to maintain and attract critical skill personnel. Thus, a SDLV Program can smoothly transition resources from the SSP and meet the transportation needs to continue the voyage of discovery of the space exploration program.

Best, Joel↗
NASA NTRS2000

WSTF Pyrovalve Test Program Status: 2000

Extensive propulsion and pyrotechnic testing has been in progress at NASA/JSC White Sands Test Facility (WSTF) since 1995, starting with the Mars Observer Propulsion and Pyrotechnics Corrective Action Test Program (MOCATP). The MOCATP has been concluded, but extensive pyrovalve testing plus research and development continues at WSTF. Our capability to accurately characterize pyrovalve combustion product blow-by into propellant systems, evaluate hydrazine and monomethylhydrazine (MMH) thermal decomposition initiated by blow-by, and characterize valve actuation operation, continues to be used and refined. Data from this and several low blow-by pyrovalves manufactured by Conax and other corporations continues to be evaluated as a potential corrective measure for blow-by induced propellant explosions. Additionally, new measurement techniques are being developed, advanced pyrovalve development is under-way, and nondestructive examination (NDE) methods are being developed to help ensure pyrovalve safety. Starting in 2000 these data are being formatted into a pyrovalve application and testing handbook. Near-term testing includes evaluation of 3/8-in. Conax pyrovalves and other commercially available valves; development of advanced pyrovalve subcomponent technology; investigation of NDE techniques to evaluate pyrovalve ram seals and real-time measurement of housing deformation; and investigation of pyrotechnically induced explosive hydrazine decomposition both through testing and modeling. Evaluation of 3/8-in. Conax valves is to include operational margin testing to be accomplished at the NASA Langley Research Center.

Saulsberry, Regor L.↗
DOE OSTI2025

Water intensity of photovoltaic module manufacturing at the terawatt scale

As the U.S. ramps photovoltaic (PV) manufacturing to the terawatt scale and emphasizes re-shoring manufacturing, potential regional impacts on the U.S. water supply should be considered, particularly since many PV companies rely almost exclusively on public water supplies for manufacturing. This work surveys the academic literature and PV manufacturer reports to estimate the water intensity of monocrystalline silicon, multicrystalline silicon, and cadmium telluride modules manufactured at the terawatt scale, determining that on average, cadmium telluride manufacturing is less water intensive on a per megawatt scale – this is anticipated to be true for all thin film PV manufacturing. While much lower than the water intensity of thermoelectric (e.g., coal) energy generation, significant issues and gaps with PV manufacturing data quality in academic studies are identified which cause estimates to vary by over 1000x (0.04 – 49 trillion liters/terawatt). Data issues are discussed and the need for accurate accounting of water resources (e.g., via continuous, updated information during PV manufacturing) is highlighted. The opportunity to reconfigure decommissioned thermoelectric sites to PV manufacturing is also explored. Finally, factors that influence PV manufacturing water intensity, from individual manufacturing steps to trends across the PV industry, are examined and water conservation opportunities are presented.

14 SOLAR ENERGY↗
DOE OSTI2024

Design and development of the magnetic diagnostic systems for the first operational phase of the SMART tokamak

A set of magnetic diagnostics has been designed, manufactured, and calibrated for the first operational phase of the small aspect ratio tokamak. The sensor suite comprises of Rogowski coils; 2D magnetic probes; and poloidal, saddle, and diamagnetic flux loops. Here, a set of continuous Rogowski coils has been manufactured for the measurement of plasma current and induced eddy currents in conductive elements. A set of flux loops and magnetic probes will be used as input for the reconstruction of the magnetohydrodynamic equilibrium. The quantity and position of these sensors have been verified to be sufficient with synthetic equilibrium reconstructions using the equilibrium fitting code and baseline scenarios computed with the Fiesta code. These sensors will also be used as input for the real-time control system, and magnetic probes will be used for the detection of plasma instabilities. The calibration procedure for the magnetic probes is described, and the results are shown. The signal conditioning and data acquisition systems are described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

NASA's Office Safety Mission Assurance Efforts to Improve Non-destructive Evaluation Methods for Additive Manufacturing and In-Space Inspection

National Aeronautics and Space Administration (NASA) continues to push the boundary of manned flight. Current mission profiles include flights to the Moon and Mars. Many of these missions require advance manufacturing and planned off planet resource utilization. As NASA continues to develop highly advance materials and manufacturing techniques to meet these mission profiles, inspection of these increasingly complex parts has had to evolve as well. Additive manufacturing is coming to the forefront as a primary manufacturing technique but offers unique challenges when inspection and certification are required. NASA has been working diligently to be a leader in developing and utilizing inspection techniques capable of inspecting these highly advanced parts. Additionally additive manufacturing techniques can also be used to build parts in space and provides a vehicle for in-situ resource utilization for off world missions. As NASA and its commercial crew partners move forward, inspection techniques will need to continue to advance to ensure safe manned space flight. In this talk NASA will highlight many of the advanced nondestructive evaluation efforts going on across the agency, as well as providing highlights for points of infusion for helping NASA meet its future mission goals.

NDE↗
DOE OSTI2024

Automated Manufacturing of Grid Stiffened Panels with Radically Reduced Tooling

Grid stiffened continuous fiber reinforced composite panels are an attractive option for creating lightweight structures due to the tailorability for various applications and the resulting high specific properties. However, the panel stiffeners and stiffener intersections result in high tooling complexity and correspondingly high cost of implementation. These factors have limited the impact of such structures in the composites industry. Previous research has demonstrated the ability to produce high quality, high aspect ratio beams, representative of individual grid stiffeners, using E-glass/PET comingled tow via direct digital manufacturing. Further, prior preliminary efforts have demonstrated the potential to use the same approach to manufacture grid intersections that have continuous fiber in both directions. To expand on the previous efforts in grid stiffeners produced by direct digital manufacture with radically reduced tooling requirements, this effort compares two methods of providing positioning and consolidation, nozzle vs. roller. Both processes are based on a commingled yarn feedstock. The extrusion through a nozzle has been shown to enable grid intersection control through local variations in applied consolidation and serves as the baseline process. However, this approach requires a continuous placement path to create the complete grid stiffened panel as no mechanism for cutting and restarting has been implemented. Alternatively, a newly developed placement head incorporating cut and refeed, mounted to a 6-axis robot, offers the potential of improved path placement efficiency. The two techniques are used to produce similar grid composite stiffeners to evaluate the effectiveness of producing the grid intersections. Rate of deposition of the two end effectors are compared and the quality of the associated grid stiffeners, and intersections, are determined through measurement of geometry, fiber volume fraction and void fraction.

Engineering↗
DOE OSTI2021

A deterministic verification strategy for electrostatic particle-in-cell algorithms in arbitrary spatial dimensions using the method of manufactured solutions

As simulations of kinetic plasmas continue to increase in scope and complexity, a rigorous and straightforward method for verifying particle-in-cell (PIC) implementations is necessary to ensure their correctness. Here, in this paper, we present a deterministic method for the rigorous verification of multidimensional, multispecies, electrostatic particle-in-cell codes based on the method of manufactured solutions. Specifically, we prove that rigorous verification is possible through the exclusive examination of errors of grid quantities (i.e., moments and/or fields), allowing for a very light-weight and non-intrusive implementation in existing PIC codes. This is a marked improvement over earlier PIC verification approaches (only demonstrated with one species in 1D-1V), which rely on the comparison of cumulative distribution functions, and are invasive on the code base, introduce additional stochastic noise, are significantly more computationally expensive, and lack rigorous convergence properties. Interestingly, we show that different grid quantities feature different rates of convergence with the number of particles and mesh size, impacting the verification process. These theoretical results are confirmed numerically with a multi-species 2D-2V particle-in-cell code, including the ability of the method to detect order reduction due to an incorrect implementation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Thermal Instability in the Manufacturing of Wind Turbine Blade Spar Caps

As wind turbine blades continue to scale in length and total mass, the acceptability of traditional approaches for the engineering of processes to build these products has reached a limit. The continued need to reduce the levelized cost of energy (LCOE) drives manufacturing cycle times lower and the net mass of critical components challenges even the most experienced fabricators to meet the quality requirements for safe operating performance over the 25-year design life of the blade. In trying to reduce cycle time for key components of wind turbines, manufacturers discovered occasional buckling of fibers in wind turbine blade spar caps. The cause of the buckling was unknown. The goal of this project was to show that a comprehensive simulation, which considered all of the physics of the VARTM process, could identify the cause of the fiber buckling in spar caps that has been observed during the manufacturing process. Ultimately, the simulation determined the manufacturing process and parameters could lead to significant compressive stresses in the fibers eventually causing buckling. Simulation results suggest that the stress introduced from friction is the largest source of compressive stress in the fibers, the stress from the weight of gravity is significant but secondary, and the compressive stress from cure shrinkage does not play a significant role in the buckling of fibers. This report provides details of the testing and simulation methodology used to identify the cause of the fiber buckling.

17 WIND ENERGY↗
DOE OSTI2023

Photovoltaic Deployment Scenarios toward Global Decarbonization: Role of Disruptive Technologies

To totally decarbonize global electrical systems using photovoltaics (PVs) in the 2050–2060 decade, the world would need to install 63.4 TW of PV. This article models and explores how a PV manufacturing ramp‐up trajectory toward this goal can be achieved while assuming that investors continue to make financially rational decisions avoiding stranded production assets and therefore protecting their return on investment. The model effectively exploits experience curve benefits in both the scaling of the manufacturing process and continued progress in product design technologies. The scale‐up challenge is amplified because trajectories that achieve this goal require an unprecedented ramp‐up of production capacity over just two decades, followed by relatively modest demand to maintain the installed base and support continued population growth. It is demonstrated that sustainable ramp‐up of manufacturing is indeed possible and shown that the deployment of the requisite manufacturing capacity can be accelerated and accomplished at lower total capital cost by the introduction of disruptive technologies that have lower capital intensity, embedded energy, or higher efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

Cost Efficient and Highly Weather-Resistant Solar Panel Backsheet Produced through Continuous Co-Extrusion Processing

The efficient generation and delivery of ‘clean energy” through photovoltaic (PV) technology relies heavily on the cost, performance and reliability of solar panels, along with the individual components used in assembly of those panels. In order to continue towards the Department of Energy’s (DOE) goals of driving costs down, the lifetime of high-output power generation equipment (i.e. solar modules) must be extended to reduce costs associated with power output degradation and replacement of failed or degraded panels. One of the major sources of module failures in the past 30 years has been the failure of the solar panel backsheet. Failure of this component causes severe output losses due to oxidation and yellowing of the module while creating safety concerns as the major electrical insulation of the module is compromised. Tomark-Worthen LLC was formed in 2012 with the goal of designing and manufacturing novel PV backsheets and encapsulants that would be produced in the United States of America and exceed expectations of domestic and international module producers. These backsheets would improve upon known backsheet design failures (i.e. Isovoltaic’s AAA backsheet) and create domestic manufacturing jobs in the PV sector. This goal became a reality with a first-generation product in 2018 and now, with the support of the DOE, Tomark-Worthen has launched a second-generation product known as PhotoMark® Reflections™ 205-3 and 360-3. This 2+ year effort began in late 2017 with a screening of potential polymeric materials and backsheet structural designs. Performance evaluations of each material provided the necessary data needed to select the proper material combinations and move forward into the design of the manufacturing process. These decisions were made by teaming with a local university, well-respected government laboratories, and private research organizations who provided the tools necessary to predict long-term performance of these materials in much shorter periods of time. Once the go/no-go criteria were met at the mid-point of the project, the effort transitioned to predicting 30+ year performance, achieving certifications, and improving manufacturing efficiencies designed to lower costs in order to be competitive in a cost-driven market. Major project accomplishments include recognition of the new backsheet by Underwriters Laboratories (UL) and international certification for 1000V and 1500V modules by TUV Sud. Both 1000V and 1500V products have been proven on several module manufacturing lines and initial customer orders have been received by both domestic and international module producers. Accelerated exposure testing has shown that the performance of this backsheet exceeds the prior polyamide-based backsheet known to fail in the field. Cost-models and initial customer orders have shown the ability to produce this backsheet at a cost acceptable to many domestic manufacturers, while International costs for standard backsheet remains extremely low. Tomark-Worthen remains one of the only U.S. companies manufacturing backsheet domestically and this has drawn interest from many domestic module manufacturers looking to improve their material supply logistics by avoiding long lead times and custom’s headaches while avoiding current tariffs on Chinese-made components. Along with the launch of a new PV backsheet, this project has provided a critical deliverable to the PV R&D community. This deliverable is the knowledge that not all polyamide-containing backsheets are doomed to failure as the earlier versions did. There has been a fear amongst the PV community to consider these materials due to the failure of one design. This effort has brought a new level of interest to the scientific community as it has been shown that polyamides can be used successfully in a well-designed backsheet. As we move forward from this project, we are excited to see how backsheet technology and manufacturing in the U.S. will continue to progress and grow.

14 SOLAR ENERGY↗
DOE OSTI2022

Improving fatigue performance of additively manufactured Ti-6Al-4V using sulfur-based self-terminating etching processes

The adoption of Additively Manufactured (AM) Ti-6Al-4V (Ti64) is continually increasing in the industry due to its benefits over the conventional manufacturing techniques. However, AM Ti64 parts are prone to poor surface finish, which significantly affects their fatigue performance. Therefore, AM Ti64 parts need post-processing to enhance surface finish and fatigue performance. Prior work with a sulfur-based self-terminating etching process for AM Ti64 demonstrated support removal and surface roughness reduction. To further this work, this manuscript details the impact of this sulfur-based post-processing technique on the mechanical properties and the fatigue life of AM Ti64 by characterizing the surface roughness, microstructural evolution, and fracture surfaces. Finally, this post-processing technique decreased the surface roughness parameter - S v by 55 % from 84 ± 11 µm to 38 ± 19 µm and increased the average fatigue life by 340 % from about 7000 cycles to 30,000 cycles.

36 MATERIALS SCIENCE↗