Search NASA⌕ Search

SEARCH · Search NASA

Results for “Control Account”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Information management system breadboard data acquisition and control system.

Description of a breadboard configuration of an advanced information management system based on requirements for high data rates and local and centralized computation for subsystems and experiments to be housed on a space station. The system is to contain a 10-megabit-per-second digital data bus, remote terminals with preprocessor capabilities, and a central multiprocessor. A concept definition is presented for the data acquisition and control system breadboard, and a detailed account is given of the operation of the bus control unit, the bus itself, and the remote acquisition and control unit. The data bus control unit is capable of operating under control of both its own test panel and the test processor. In either mode it is capable of both single- and multiple-message operation in that it can accept a block of data requests or update commands for transmission to the remote acquisition and control unit, which in turn is capable of three levels of data-handling complexity.

Mallary, W. E.↗

Approach guidance logic for a tilt-rotor aircraft

The distinctive feature of a tilt-rotor aircraft is that the pilot can change the rotor mast angles to go from a helicopter configuration for take-off and landing to an airplane configuration for high cruise speeds and vice-versa. An approach path for such an aircraft is proposed and the logic required to fly along this path in the presence of wind is determined. The main contribution of this work is an efficient and, to my knowledge, new method for generating the nominal state and control histories taking into account an estimate of the mean wind velocity and direction. The method requires the solution of algebraic (mostly linear) equations to generate a 'universal nominal', and feedforward and feedback gains. Then, in flight the additional state and control corrections due to deviation in descent rate, deceleration, and flight in a steady wind are obtained by multiplying simple precalculated functions of time by descent rate, deceleration or sine and cosine components of the mean wind vector. Simulations of approach flights for different wind conditions, assuming perfect state information in the feedback signal, indicated satisfactory performance.

Beser, J.↗

Full Gradient Solution to Adaptive Hybrid Control

This paper focuses on the adaptation mechanisms in adaptive hybrid controllers. Most adaptive hybrid controllers update two filters individually according to the filtered-reference least mean squares (FxLMS) algorithm. Because this algorithm was derived for feedforward control, it does not take into account the presence of a feedback loop in the gradient calculation. This paper provides a derivation of the proper weight vector gradient for hybrid (or feedback) controllers that takes into account the presence of feedback. In this formulation, a single weight vector is updated rather than two individually. An internal model structure is assumed for the feedback part of the controller. The full gradient is equivalent to that used in the standard FxLMS algorithm with the addition of a recursive term that is a function of the modeling error. Some simulations are provided to highlight the advantages of using the full gradient in the weight vector update rather than the approximation.

Bean, Jacob↗

Full Gradient Solution to Adaptive Hybrid Control

This paper focuses on the adaptation mechanisms in adaptive hybrid controllers. Most adaptive hybrid controllers update two filters individually according to the filtered reference least mean squares (FxLMS) algorithm. Because this algorithm was derived for feedforward control, it does not take into account the presence of a feedback loop in the gradient calculation. This paper provides a derivation of the proper weight vector gradient for hybrid (or feedback) controllers that takes into account the presence of feedback. In this formulation, a single weight vector is updated rather than two individually. An internal model structure is assumed for the feedback part of the controller. The full gradient is equivalent to that used in the standard FxLMS algorithm with the addition of a recursive term that is a function of the modeling error. Some simulations are provided to highlight the advantages of using the full gradient in the weight vector update rather than the approximation.

Bean, Jacob↗

Results from a 'small box' realtime molecular contamination monitor on STS-3

On the basis of early estimates of the Shuttle induced environment, Scialdone (1979) concluded that in the vicinity of the cargo, the cargo would have the largest influence on the environment. As a contamination control device, realtime monitors can indicate safe operational periods for sensitive attached payloads. It was, therefore, decided to develop the OSS-1/Contamination Monitor Package (CMP) experiment which was seen as a forerunner of an operational monitor. A description of the CMP is provided, taking into account four actively temperature controlled quartz crystal microbalances (TQCM). The TQCM temperatures could be varied from -60 C to +80 C. The sensor consisted of a matched pair of quartz crystals. The crystals were designated as a sensor and reference crystal. Results obtained during the STS-3 mission are discussed. These results show the feasibility and advantages of a small real-time contamination monitor.

Triolo, J.↗

On the relationship between reliability and linear quadratic optimal control

The linear quadratic optimal control method is used today to solve many complex systems problems. As system complexity increases, and as linear quadratic optimal control is used in more demanding situations, the extension of the design methodology to cover system failures, robustness and reliability is of crucial importance. This paper documents the progress toward a theory which incorporates reliability in the performance index; a linear quadratic control problem is formulated which accounts for system effectiveness and gives an offline procedure for comparing two linear quadratic control systems on the basis of both reliability and performance.

Birdwell, J. D.↗

Application of stochastic optimal reduced state feedback gain computation procedures to the design of aircraft gust alleviation controllers

A stochastic linear model that accounts for process parameter and initial uncertainty, measurement noise, and a restricted number of measurable outputs was used to determine feedback gains useful for reducing the vertical acceleration which results from the presence of a vertical wind gust. Considered in the study were the influence of various feedback configurations, the effects of sensor noise, flight condition changes, and initialization procedures. Results showed that for sixth order linearized longitudinal motion, a controller with feedback on three states could be designed for effective gust alleviation taking into account both sensor noise and flight condition variation.

Sobel, K.↗

Physical model-set identification for robust control of flexible structures

An approach to dynamic system identification is presented taking into account the goal of enhancing robust control performance of flexible structures. Identification techniques are derived which take advantage of the physics of structural dynamics and can provide realistic bounds for all potential parameter uncertainties. The developed approach includes input optimization which distributes excitation energy in such a way that the influence of residual uncertainties on robust control performance is reduced.

Karlov, Valeri I.↗

Performance index sensitivity of minimum-fuel systems.

The purpose of this paper is to investigate the effects of small parameter variations on the performance index of minimum-fuel systems with initial and final manifolds. The pulse-shaped variations produced by the parameter change on the piecewise-constant control are taken into account in order to derive the trajectory sensitivity equation. It is proved that the variation of the performance index is related to those of the trajectory and the parameter by a simple expression. This expression extends, to the class of minimum-fuel problems, a re sult obtained by Kokotovic et al. for systems with continuous, unconstrained controls.

Courtin, P.↗

Dynamic verification of a digital flight control system.

Development of a digital control system dynamic variation technique which accounts for the limitation of available frequency response analyzers. Digital control system theory is briefly reviewed, and generation of the necessary theoretical frequency responses is discussed. Results of the dynamic verification of a digital control system for a Saturn V launch vehicle are presented, and attention is given to the limitations of this technique along with its applicability to other types of digital control systems. A technique for performing open-loop frequency response analyses of a flight program implemented in a 'flight-type' digital computer and interface hardware with vehicle dynamics simulated on an analog computer is described.

Nabers, J. P., Jr.↗

Optimal controllers for finite wordlength implementation

When a controller is implemented in a digital computer, with A/D and D/A conversion, the numerical errors of the computation can drastically affect the performance of the control system. There exists realizations of a given controller transfer function yielding arbitrarily large effects from computational errors. Since, in general, there is no upper bound, it is important to have a systematic way of reducing these effects. Optimum controller designs are developed which take account of the digital round-off errors in the controller implementation and in the A/D and D/A converters. These results provide a natural extension to the Linear Quadratic Gaussian (LQG) theory since they reduce to the standard LQG controller when infinite precision computation is used. But for finite precision the separation principle does not hold.

Liu, K.↗

Rotor dynamic behaviour of a high-speed oil-free motor compressor with a rigid coupling supported on four radial magnetic bearings

The combination of a high-speed motor, dry gas seals, and magnetic bearings realized in this unit facilitates the elimination of oil. The motor is coupled with a quill shaft to the compressor. This yields higher natural frequencies of the rotor than with the use of a diaphragm coupling and helps to maintain a sufficient margin of the maximum speed to the frequency of the second compressor bending mode. However, the controller of each bearing then has to take the combined modes of both machines into account. The requirements for the controller to ensure stability and sufficient damping of all critical speeds are designed and compared with the implemented controller. The calculated closed loop behavior was confirmed experimentally, except the stability of some higher modes due to slight frequency deviations of the rotor model to the actual rotor. The influence of a mechanical damper as a device to provide additional damping to high models is demonstrated theoretically. After all, it was not necessary to install the damper, since all modes cold be stabilized by the controller.

Schmied, J.↗

Initial Testing Results and Forward Design Considerations for the Tri-Rotor Hand Controller

The Lunar Terrain Vehicle (LTV) is one of the key elements of NASA’s Artemis return to the Moon. As an unpressurized rover, the LTV hand controller must take into account the limitations of the spacesuit worn by the crew as well as lessons learned operating the Apollo Lunar Roving Vehicle and preliminary NASA simulations. Because the NASA Ground Test Unit (GTU) design features omnidirectional steering, NASA engineers developed the TriRotor is an innovation to minimize crew fatigue and discomfort. NASA conducted a series of tests, initially with 3D printed mockup controllers, and expanding to a functional prototype used in an LTV video wall simulation. The Tri-Rotor compared favorably with legacy Apollo T-Handles, though numerous test subject comments were collected to improve the controller’s usability. Several options to improve the Tri-Rotor’s usability are also discussed, along with opportunities to test the Tri-Rotor in Virtual Reality, a motion table, and in field analogs.

Hand Controller↗

Method of controlling a resin curing process

An analytical technique for controlling the curing process of fiber-reinforced composite materials that are formed using thermosetting resins. The technique is the percent gel method and involves development of a time-to-gel equation as s function of temperature. From this equation a rate-of-gel equation is then determined, and a percent gel is calculated which is the product of the rate-of-gel times time. Percent gel accounting is used to control the proper pressure application point in an autoclave cure process to achieve desired properties in a production composite part.

Charles Neal Webster↗

Survey of prospective techniques for molten salt reactor feed monitoring

Safeguards verification measurements of nuclear material content in fresh fuel salt for liquid-fueled molten salt reactors (MSRs) are likely to be required as part of nuclear material accountancy for International Atomic Energy Agency safeguards. Here, this paper presents a comprehensive review and evaluation of 18 potential candidate techniques to quantify total uranium and 235 U for input accountancy measurements for liquid-fueled MSRs. As part of an overall screening and down-selection effort to identify the most promising techniques for further development for an MSR feed monitoring system, this paper defines eight figures of merit (FOMs): reasonably achievable measurement uncertainty, measurement time required, capital cost, burden upon the facility operator, maintenance intensity, technological maturity, human capital requirements for operation, and whether the technique introduces a path for potential material removal. Each candidate technique is then evaluated across these FOMs to identify the techniques with the highest potential for future development for fresh fuel accountancy measurements in MSRs. Our findings indicate that no single technique or combination thereof currently has the requisite technological maturity for immediate implementation in nuclear material accountancy at a liquid-fueled MSR facility. While several promising techniques are identified, there is a critical lack of experimental data for most systems in the context of molten salt applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nonlinear Dynamic Control Derivative Analysis for Aircraft with Application to Transonic Truss-Braced Wing

This paper presents the development of a nonlinear dynamic control derivative estimation method. A nonlinear aerodynamic model is developed to account for the effects of large control surface deflections on aircraft aerodynamic forces and moments. A series of unsteady RANS CFD simulations is performed to simulate the control surface oscillations at various reduced frequencies. The time-domain data are transformed into the frequency-domain data by a Fourier series analysis. Transfer functions of the dynamic control derivatives are then estimated by a frequency-domain regression. The method is applied to the Transonic Truss-Braced Wing (TTBW) to estimate the dynamic control derivatives for the elevator, aileron, and rudder.

Aircraft Control Derivatives↗

Human Stability While Exercising on a VIS Device in Zero Gravity

BACKGROUND: A Vibration Isolation and Stabilization (VIS) system is being designed for use with the European Enhanced Exploration Exercise Device (E4D) [1]. The exercise bar is attached to cables that extend and retract through openings in the E4D platform, which the subject stands on while exercising. Since the E4D is mounted on a moving VIS device, the whole system moves under the subject’s feet. While tension in the cables does help stabilize a crew member in 0g by bracing him or her against the moving platform, flexible cables do not offer full support against falling. This raises the question of whether various exercises that are successfully performed in 1g on a stationary device can be performed without losing balance in 0g on a moving device. Quantifying stability conditions and establishing stability requirements for exercise countermeasure systems is a long-standing challenge and this work helped to inform this specific need for integrated E4D/VIS flight project development. METHODS AND RESULTS: A simplified stability analysis can be attempted based on platform accelerations generated by the VIS device simulation. In this type of analysis, the subject is conceived as standing on the platform in 0g while being held down to it by the tension in the cables. If the sideways acceleration of the platform is such that the cables cannot generate a sufficient moment relative to, e.g., the heels or the toes of the subject to overcome the tipping moment from the inertial forces on the accelerated subject’s body, the subject becomes unstable. This approach, which we refer to as the ‘static’ approximation, indicated failure of all the exercises that were considered in the comprehensive VIS analysis of the E4D. It was realized, however, that platform accelerations are not externally imposed but are themselves induced by the motion of the subject’s body during exercise, and a model calculation confirmed that this drastically altered the tipping moment on the subject, with the potential to even switch the direction in which the body would tip over. This made it imperative to consider in a coupled manner both the motion of the exercising subject’s body and the induced VIS platform motion while considering stability. The coupled dynamics requirement was met by the VIS simulation incorporating time-dependent human mass properties atop the platform and driven by the inertial forces from the prescribed subject motion relative to the platform based on motion-capture recorded human trajectories in 1g on a stationary E4D [2]. To analyze simulation results, a stability criterion was also needed. We do not know how to account for the human ‘control system’ that would take visual and vestibular cues as inputs as the platform moves in 0g. We thus chose to follow an approach we had previously used to analyze the dynamic feasibility of performing a task in lunar gravity along the human body trajectory recorded in 1g [3]. In this approach, one analyzes the center of pressure (COP) between the shoes and the ground (or platform) and checks if the COP remains within the convex hull of the footprints on the ground (or platform), commonly referred to as base of support (BOS). Since pressure is vertical and, in the absence of foot restraints, positive, the COP going outside the BOS indicates that the trajectory recorded in 1g is not dynamically feasible in microgravity and/or on the moving platform of the device. The outcome of the COP-based analysis was that some of the key exercises, especially the deadlift and the back squat exercises, were found to be dynamically feasible for at least some number of the exercise cycles, this number increasing with the cable tension. While this type of stability analysis does not account for the likely alteration of the exercise trajectory from its 1g form in space, it does show that there exist at least some realistic trajectories that pass the dynamic feasibility criterion. This adds confidence that, with further adjustment by the subject of the exercise form in 0g on a moving device, a number of exercises can be performed without losing balance.

D Frenkel↗

Active control of helicopter transmission noise

An account is given of an effort to reduce helicopter transmission noise by 10 dB, using active methods, as part of the NASA-Lewis/U.S. Army Propulsion Directorate Advanced Rotorcraft Transmission technology integration and demonstration program. The transmission used as a test stand is that of the CH-47C forward rotor. Attention is presently given to the active control system's actuators, sensors, and control algorithms.

Spencer, R. H.↗