Rationalizing the Effects of Corrosion, Irradiation and Stresses on the Mechanical Performance of Structural Alloys Used Molten Salt Reactors
Explore the source record for details and available documents.
Andersson, Anders David Ragnar↗
SEARCH · Search NASA
Results for “Corrosion performance”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy
High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.
Corrosion performance↗
Stress Corrosion Evaluation of NiTiHf Alloy for the International Space Station Environmental Control and Life Support System
A stress corrosion evaluation was performed on NiTiHf alloy because this material is considered a bearing material candidate for the Environmental Control and Life Support System. Stressed round tensile specimens survived exposures to alternate pretreat, alternate brine, baseline pretreat, baseline brine, and 3.5% NaCl alternate immersion. Metallographic evaluations did not detect stress corrosion on exposed samples. The ultimate tensile strength values varied significantly for this material, which is common for bearing materials. This variation was observed on both, exposed and nonexposed specimens. The results of this work indicate that this material has potential applications as a bearing material.
International Space Station (ISS)↗
Corrosion of Al-Fe self-pierce riveting joints with multiphysics-based modeling and experiments
Self-piercing riveting (SPR) is an extensively used joining technique to assemble dissimilar materials. However, this joining of the dissimilar materials can generate galvanic/crevice corrosion, which can drastically impact the mechanical properties and the service life of the joint. In this study, a multiphysics-based hybrid modeling approach is developed for the galvanic corrosion of the Al-Fe SPR joints, which can consider the corrosion initiation and corrosion evaluation jointly. Experimental studies are first performed to extract information regarding the corrosion initiation sites, corrosion evolution and overall corrosion induced material loss in SPR joints. The initiation information is then passed onto the multiphysics FE model thus making it a hybrid model. This model can help understand the influences of metal microstructure on the corrosion propagation while the morphology changes can also be analyzed. Using the developed hybrid modeling approach, thorough parametric studies can be performed to explore the coupled impacts of multiple corrosion factors on the corrosion behavior of the joints. The developed hybrid model is validated on the prediction of galvanic corrosion for the SPR joints by comparing with experimental observations.
36 MATERIALS SCIENCE↗
Study of metal corrosion using ac impedance techniques in the STS launch environment
AC impedance measurements were performed to investigate the corrosion resistance of 19 alloys under conditions similar to the STS launch environment. The alloys were: Zirconium 702, Hastelloy C-22, Inconel 625, Hastelloy C-276, Hastelloy C-4, Inconel 600, 7Mo + N, Ferralium 255, Inco Alloy G-3, 20Cb-3, SS 904L, Inconel 825, SS 304LN, SS 316L, SS 317L, ES 2205, SS 304L, Hastelloy B-2, and Monel 400. AC impedance data were gathered for each alloy after one hour immersion time in each of the following three electrolyte solutions: 3.55 percent NaCl, 3.55 percent NaCl-0.1N HCl, and 3.55 percent NaCl-1.0N HCl. The data were analyzed qualitatively using the Nyquist plot and quantitatively using the Bode plot. Polarization resistance, Rp, values were obtained using the Bode plot. Zirconium 702 was the most corrosion resistant alloy in the three electrolytes. The ordering of the other alloys according the their resistance to corrosion varied as the concentration of hydrochloric acid in the electrolyte increased. The corrosion resistance of Zirconium 702 and Ferralium 255 increased as the concentration of hydrochloric acid in the electrolyte increased. The corrosion resistance of the other 17 alloys decreased as the concentration of the hyrdochloric acid in the electrolyte increased.
Calle, Luz M.↗
High-Temperature Active Magnetic Bearing Development for Supercritical CO 2 Machinery Applications
Hermetic machinery utilizing gas bearings for MW-scale supercritical CO 2 (sCO 2 ) machinery applications can have significantly lower power loss and enable improved cycle efficiency compared to conventional machinery with oil-lubricated bearings. Active magnetic bearings (AMBs) are another option anticipated to have similar power loss and load capacity to gas bearings as well as offering larger mechanical tolerances, the ability to tune properties, and high reliability due to lack of mechanical wear. AMBs also have proven commercial experience at MW-scale, though environments for high-temperature sCO 2 power cycle machinery conditions are novel. Besides the potential impact of AMBs for sCO 2 turbomachinery, the technology also offers promising benefits for steam and gas turbines for power generation, compressors and expanders for industrial heat and power, and in other oil and gas and space applications. The goals of this project were to conceptual design an AMB and perform material testing. Conceptual designs for radial and thrust AMBs were produced based on a hermetically-sealed sCO 2 machinery waste-heat recovery (WHR) application for sizing and loads, and choosing a target design temperature of 540°C useful for high-temperature sCO 2 turbines for concentrating solar power (CSP) applications. Conceptual designs were initially developed for multiple radial and thrust AMBs with spreadsheet-based calculations before selecting one of each to develop further using higher-fidelity design methods for magnetic and structural performance. It was found that the radial AMB at 540°C was feasible, but the thrust AMB needed to be limited to 315°C for high-speed operation. The decision for a reduced-temperature thrust AMB was the result of several significant conclusions: 1) Hiperco 50A, originally chosen for good magnetic performance at high temperature, had insufficient strength for high-speed operation, so it was replaced with 17-4 PH. 2) The reduced magnetic performance from 17-4 PH yielded a larger bearing size, reducing the strength margin. 3) This ultimately led to a creative design implementing a more-compact E-core topology, compared to the original (conventional) C-core, and an integral shaft-disk with Hirth joint connection. These conceptual designs are unique for the size and temperature in CO 2 , relevant for MW-scale CSP applications. Long term, high temperature test data was generated for several materials, filling a void in the current body of literature. Corrosion and magnetic performance measurements were produced for PM materials (Alnico 5-7C, Alnico 9C, and SmCo) with and without nickel-coating for environments of high-temperature CO 2 up to 550°C at atmospheric pressure and 450°C at 103 bar for up to 6,000 hours. Corrosion measurements were also produced for Hiperco 50, a SM material relevant for AMB laminations, with and without C5 coating. Comparisons were also made for 450°C and 550°C, atmospheric pressure air exposures up to 5,000 hours. Results generally show that coatings can be effective at improving oxidation resistance of the bare materials, and Alnicos generally outperformed SmCo after high-temperature exposure. In addition to technical feasibility demonstrated by the design, economic feasibility was demonstrated by updating the TEA from the reference machine, re-evaluating it with CAPEX and OPEX to reflect estimated changes from process-lubricated bearings to AMBs. AMBs were shown to be comparable in performance to process-lubricated bearings, still showing a notable improvement over conventional machinery architecture with oil-lubricated bearings.
42 ENGINEERING↗
Accelerating FEM-Based Corrosion Predictions Using Machine Learning
Atmospheric corrosion of metallic parts is a widespread materials degradation phenomena that is challenging to predict given its dependence on many factors (e.g. environmental, physiochemical, and part geometry). For materials with long expected service lives, accurately predicting the degree to which corrosion will degrade part performance is especially difficult due to the stochastic nature of corrosion damage spread across years or decades of service. The Finite Element Method (FEM) is a computational technique capable of providing accurate estimates of corrosion rate by numerically solving complex differential Eqs. characterizing this phenomena. Nevertheless, given the iterative nature of FEM and the computational expense required to solve these complex equations, FEM is ill-equipped for an efficient exploration of the design space to identify factors that accelerate or deter corrosion, despite its accuracy. In this work, a machine learning based surrogate model capable of providing accurate predictions of corrosion with significant computational savings is introduced. Specifically, this work leverages AdaBoosted Decision trees to provide an accurate estimate of corrosion current per width given different values of temperature, water layer thickness, molarity of the solution, and the length of the cathode for a galvanic couple of aluminum and stainless steel.
36 MATERIALS SCIENCE↗
The stress corrosion resistance and the cryogenic temperature mechanical properties of hot rolled Nitronic 32 bar material
The ambient and cryogenic temperature mechanical properties and the ambient temperature stress corrosion properties of hot rolled and centerless ground Nitronic 32 stainless steel bar material are presented. The mechanical properties of longitudinal specimens were evaluated at test temperatures from ambient to liquid hydrogen. The tensile test data indicated increasing smooth tensile strength with decreasing temperature to liquid hydrogen temperature. However, below -200 F (-129.0 C) the notched tensile strength decreased slightly and below -320 F (-196.0 C) the decrease was significant. The elongation and reduction of area decreased drastically at temperatures below -200 F (-129.0 C). The Charpy V-notched impact energy decreased steadily with decreasing test temperature. Stress corrosion tests were performed on longitudinal tensile specimens stressed to 0, 75, and 90 percent of the 0.2 percent yield strength and on transverse 'C'-ring specimens stressed to 75 and 90 percent of the yield strength and exposed to: alternate immersion in a 3.5 percent NaCl bath, humidity cabinet environment, and a 5 percent salt spray atmosphere. The longitudinal tensile specimens experienced no corrosive attack; however, the 'C'-rings exposed to the alternate immersion and to the salt spray experienced some shallow etching and pitting, respectively. Small cracks appeared in two of the 'C'-rings after one month exposure to the salt spray.
Montano, J. W. L.↗
Future Opportunities for LWR Irradiations in US Test Reactors
After several years of relatively low activity in the field of Light Water Reactor (LWR) fuel development, the Department of Energy again began to engage in developing new fuel technologies and irradiation performance data prompted by the Fukushima Daichi nuclear accidents. New competencies for irradiation testing in material test reactors in the United States began to be developed at this time using the Advanced Test Reactor (ATR), High Flux Isotope Reactor (HFIR), Massachusetts Institute of Technology Reactor (MITR), and the Transient Reactor Test Facility (TREAT). Capsules for testing fuel and cladding materials in ATR and HFIR were deployed, a Pressurized Water Reactor (PWR) condition loop for testing fuel rods was established in ATR, cladding corrosion studies were performed using a water loop in MITR, and TREAT pulse testing capabilities were commissioned for fuel rods in water capsules. The more recent and unexpected closure of the Halden Boiling Water Reactor (HBWR) also prompted further investments in Loss of Coolant Accident (LOCA) testing capabilities at TREAT. New configurations of these test devices show further potential in enhanced steam condition control and other investigations are building toward a flowing water loop for testing transient to dryout conditions. The closure of HBWR also prompted a major project currently underway to construct additional water loops in ATR where a novel approach is being pursued to enable Boiling Water Reactor (BWR) conditions. A meaningful collaborative project was awarded to MITR which, amidst an unexpected major overhaul of the reactor, has expanded cladding corrosion test capabilities at MITR. New explorations have led to methods for unique experiments at HFIR including channel box irradiations. New device developments are also bridging toward future potential for instrumented capsule irradiation tests in ATR and HFIR. Finally, a new project referred to as the System Physics Advanced Reactor Critical facility (SPARC) is gaining traction towards a large zero-power reactor able to produce physics validation data for LWR fuel bundle designs with increased enrichment and enhanced absorbers for 24-month operation cycles. This paper provides a brief summary of the status of these irradiation testbed capabilities with an emphasis on current efforts toward future capabilities to obtain new data and maximize the performance potential of LWR fuel technologies.
Woolstenhulme, Nicolas [Idaho National Laboratory ↗
Uncertainty Quantification for Dissimilar Material Joints Under Corrosion Environment
Abstract Self-Piercing Riveting (SPR) is one of the most commonly used methods for joining dissimilar materials in the automotive industry. These joints are popular due to their adaptability, high performance and short cycle time. However, since these joints involve two dissimilar materials, they are susceptible to galvanic corrosion in the presence of an electrolyte which is driven by the difference in the equilibrium potential of the metals. This can affect the safety and resilience of these joints. In this paper, we focus on galvanic corrosion in Al-Fe SPR joints. A Machine learning (ML) based surrogate model, which is based off of FE simulations, for statistical corrosion analysis is developed. This model enables the resilience and reliability analysis of SPR joints under corrosion environment. In this study, first a physics-based finite element (FE) corrosion model has been developed to simulate the galvanic corrosion between a Fe cathode and an Al anode of a SPR joint. This model takes into account the effect of the crystal microstructure of the Al anode and the precipitation of the corrosion product. Several geometric and environmental factors including crevice gap, roughness of anode, conductivity, pH and the temperature of the electrolyte that effect corrosion are investigated. A thorough Uncertainty Quantification (UQ) analysis is conducted for the overall corrosion behavior of the Fe-Al SPR joints using a novelistic Probabilistic Confidence-Based Adaptive Sampling (PCAS) technique. PCAS is used to train the surrogate model by identifying the critical sampling points and thus reducing the overall computational costs. It is found that the electrolyte temperature has the largest effects on the material loss and needs to be managed closely for better corrosion control. By understanding the corrosion performance and resultant uncertainty impact on SPR joints, the reliability and resilience of these joints can be improved.
36 MATERIALS SCIENCE↗
Stress Corrosion Evaluation of Various Metallic Materials for the International Space Station Water Recycling System
A stress corrosion evaluation was performed on Inconel 625, Hastelloy C276, titanium commercially pure (TiCP), Ti-6Al-4V, Ti-6Al-4V extra low interstitial, and Cronidur 30 steel as a consequence of a change in formulation of the pretreatment for processing the urine in the International Space Station Environmental Control and Life Support System Urine Processing Assembly from a sulfuric acid-based to a phosphoric acid-based solution. The first five listed were found resistant to stress corrosion in the pretreatment and brine. However, some of the Cronidur 30 specimens experienced reduction in load-carrying ability.
Torres, P. D.↗
Irradiation and corrosion testing of laser powder bed fusion-manufactured materials in the AMMT program
The Advanced Materials and Manufacturing Technologies (AMMT) program operating under the Department of Energy Office of Nuclear Energy is accelerating the qualification and deployment of additively manufactured materials in advanced reactor environments. Laser powder bed fusion (LPBF) has emerged as a promising additive manufacturing technique to fabricate complex components with the potential of tailored material properties. In the nuclear industry, metal additive manufacturing can offer numerous advantages, such as reduced lead times, streamlined quality assurance, and cost-effective low-volume production of new and replacement components with conventional or novel materials and geometries. The rapid and effective qualification of the effect of processing variability on the performance and degradation of additively manufactured materials is essential for the deployment of these components into advanced reactor environments. As part of this effort, AMMT is performing irradiation and corrosion testing of several materials built by LPBF, including 316L and 316H stainless steels. Our efforts encompass neutron irradiation testing, ion irradiation testing, and advanced modeling to provide a robust technical basis for understanding the effect of process variability on materials degradation and developing a sound methodology for accelerated ion irradiation testing. We develop focused irradiation test plans that align well with risk-informed and technologically inclusive approaches to licensing. We will also discuss our plans and specific concerns for corrosion testing additively manufactured material, with a primary focus on molten salt and liquid sodium environments.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Numerical investigation of micro-galvanic corrosion in Mg alloys: Role of the cathodic intermetallic phase size and spatial distributions
Magnesium alloys are of increasing interest in structural applications due to their low-density, moderate specific strength and stiffness, recyclability, and high damping among other properties. However, the wide-scale applicability of magnesium alloys in structural applications has been limited due to many factors including its poor corrosion resistance. In this work, a numerical investigation to simulate the micro-galvanic corrosion behavior was performed to examine the influence of size and distribution of cathodic intermetallic phase (ß-Mg17Al12) in a Mg matrix. The ratio of cathodic to anodic surface area was kept constant in each simulation condition to understand the effect of size and spacing distributions. In general, fragmentation of a larger intermetallic particle into smaller ones was found to enhance the localized current density. However, the uniform distribution of this small intermetallic phase throughout the matrix was found to reduce the overall dissolution current density and hence, pitting corrosion severity.
Beura, Vikrant↗
Analysis of the Effects of Sea Disposal on a One-Ton Container
Excess and obsolete stocks of chemical warfare material (CWM) were sea disposed by the United States between 1919 and 1970. One-ton containers were used for bulk storage of CWM and were the largest containers sea disposed. Disposal depths ranged from 300 to 17,000 feet. Based on a Type D container assembly drawing, three independent analyses (one corrosion and two structural) were performed on the containers to address the corrosion resistance from prolonged exposure to sea water and the structural response during the descent. Corrosion predictions were made using information about corrosion rates and the disposal environment. The structural analyses employed two different finite element codes and were used to predict the buckling and material response of the container during sea disposal. The results of these investigations are summarized below. Detailed reports on each study are contained in the appendices.
Jackson, Wde C.↗
Corrosion evaluation of metal foams in eutectic molten salts for high temperature latent heat energy storage application
High-temperature Thermal Energy Storage (TES) has drawn great attention as a technology that can increase the role and profitability of micro nuclear reactors in the decentralized clean energy market. Various research needs have been proposed by Idaho National Laboratory (INL) in "the Integrated Energy Systems: 2020 Roadmap" with the goal of utilizing the high temperature of 550 degrees or more generated in the 4th generation reactor to industrial purposes from the standpoint of integrated energy systems [1]. With the recent development of the 4th generation nuclear power plant, including micro nuclear reactor, there is a great deal of interest in researching how to efficiently couple a heat source to an industrial process through thermal processing. Texas A&M University (TAMU) and INL are currently collaborating to develop a novel latent heat storage design called HITB (Heat pipe-Integrated Thermal Battery). As part of the small-scale experimental demonstration research for HITB, a study for storage medium selection was conducted at TAMU. Eutectic salts have attracted interest as high-temperature heat storage medium for HITB. Especially, chloride molten salts and fluoride molten salts are considered promising candidates due to their high melting temperature, thermal stability, and high latent heat of fusion. Since eutectic salts have poor thermal conductivity in general, it is critical to distribute materials with high thermal conductivity evenly to facilitate the charging and discharging of heat. In this study, metal foam was considered in the HITB system to overcome the poor heat transfer characteristics of eutectic salts. In order to improve heat transfer, it is necessary to study materials with high thermal conductivity, corrosion resistant to molten salts, such as fins, extended surfaces, particles, microcapsulation, or foam structure. Porous structure of copper or aluminum can increase heat transfer area, form a thermal transfer network, and increase the effective thermal conductivity of thermal storage medium [2]. Since the melting temperature is required to be at least 450? in the current HITB design, various eutectic salts are being considered. FLiNaK and FLiBe, which are famous for fluoride salts, are good candidates, but due to the sharp rise in the price of LiF recently, they are excluded for economic reasons to be applied to large-capacity thermal energy storage. On the other hand, chloride salts are very cheap and easy to obtain, have a high melting temperature, and have a high latent heat of fusion, so they are recently in the spotlight as a phase change material. However, because of the hygroscopic nature of chloride salts, HCl gas due to impurity is easy to be released and is particularly vulnerable to corrosion. Chloride eutectic salts have been tested and suggested for metal alloys that are particularly resistant to corrosion, such as SS304, SS316, Hastelloy, Inconel 625, Incoloy 800H, which has low thermal conductivity, and is very expensive [3-6]. Porous materials with high thermal conductivity such as copper and aluminum have been tested for stability in fluids such as paraffin or water as metal foam or metal fin structures, but high temperature corrosion tests were not performed on various eutectic salts yet. Therefore, this study investigated the high temperature corrosion characteristics of metal alloys, such as C10100 foam, C10100 plate, 6101 alloy foam, and SS316 plate, while immersed in the candidate eutectic salts. A total of 20 tests for SS316 coupons and 10 tests for C10100 coupons were performed to ensure the repeatability of the present measurements. Since it is difficult to completely remove the salt inside metal foam due to the complex inner structure of the metal foam, only the surface condition was observed with a microscopy and scanning electron microscopy (SEM) image, except for measuring the corrosion rate and average mass loss.
25 ENERGY STORAGE↗
Constructing Highly Durable Fuel Cell Catalysts Through Integrating Graphitic Shell‐Protected Composite Carbon Support with Gaseous Co Deposition‐Driven PtCo Intermetallics
Metal dissolution, nanoparticle agglomeration, and carbon support corrosion cause significant performance degradation of current PtCo catalysts under acidic and oxidative oxygen reduction reaction. Here, in this study, an integrated strategy is presented to design high-performance Pt 3 Co intermetallic catalysts by regulating gaseous Co deposition-driven diffusion into Pt nanoparticles supported on a composite carbon. The composite carbon is derived from ZIF-8/polyaniline, consisting of a high-surface-area (HSC) core and a protective graphitic shell (GS), which is employed to design 40 wt.% Pt/HSC@GS catalyst. The corresponding membrane electrode assemblies (MEAs) can maintain 1.09 A cm −2 at 0.7 V (20. 7% loss) after 10 000 cycles (1.0–1.5 V for carbon stability) and 1.15 A cm −2 (16.1% loss) after 150 000 cycles (0.60–0.95 V for catalyst stability). A ordered Pt 3 Co intermetallic is synthesized via a gaseous Co-deposition process, which yields a homogeneous Co-rich layer onto the Pt nanoparticles on the composite support, thereby facilitating Co diffusion into Pt crystal during subsequent ordering annealing to form the ordered intermetallic structure. This gaseous deposition leads to a thin carbon layer on PtCo nanoparticles, inhibiting particle growth during the annealing and mitigating Co dissolution under dynamic electrochemical conditions. The PtCo catalyst achieves impressive MEA performance and long-term durability (1.45 A cm −2 at 0.7 V after 120 000 cycles) under heavy-duty conditions.
30 DIRECT ENERGY CONVERSION↗
Assessment of Carbonated Brine Injection as Low-risk Strategy for Geologic Carbon Storage
The main objective of this early-phase research was to evaluate the techno-economic feasibility and risk associated with combined brine and CO 2 storage in SWD wells using brine dissolution in the North Dakota portion of the Williston Basin. Three simulation studies were conducted to investigate: (1) CO 2 phases at different conditions, (2) wellbore compatibility, and (3) long-term storage fate in reservoir. (1) A simple reservoir model and injection simulations were created using data to represent the BEST (brine extraction and storage test) site, an operational SWD facility located near Watford City, North Dakota. The pressure evolution caused by CO 2 comingled in produced water injectate in a layer cake reservoir was then modeled while tracking aqueous CO 2 throughout the project. The salinity of the injection water, the salinity of the reservoir brine, and the amount of dissolved CO 2 comingled in the injection water were varied. (2) A wellbore corrosion model was performed using the CO 2 concentrations selected based on the reservoir modeling to examine the carbonated produced water impact on wellbore. (3) Reactive transport modeling was conducted with the optimal CO 2 concentration for this injection site to study the rock-fluid interactions and CO 2 fate in the reservoir. Results suggest that CO 2 dissolved in produced water can be injected without appreciably increasing subsurface pressure or leakage risks. Pressure buildup was found to vary with salinity but not with CO 2 mass fraction. Simulation results show that lower CO 2 percent mass fraction leads to a higher amount of CO 2 that can be dissolved at a higher injection salinity. Furthermore, the long-term goal of dissolution trapping in a traditional carbon storage project is accomplished from the start, mitigating risks associated with potential migration of buoyant CO 2 , so long as the reservoir pressure and temperature are used to determine the maximum mass fraction of the dissolved CO 2 .
54 ENVIRONMENTAL SCIENCES↗
Establishing Isotopic Measurement Capabilities using Laser-Induced Breakdown Spectroscopy for the Molten Salt Reactor Campaign
Proof-of-principle H isotope ratios of aqueous aerosol systems and liquid droplets on filter paper have been measured using laser-induced breakdown spectroscopy (LIBS) with root mean square error of prediction values down to 1.9%. Molten salt reactors (MSRs) will consist of a complex chemical and radiological system consistently producing new fission products as the reactor operates. Some of these fission products and/or their daughter species will leave the salt in the reactor off-gas. Monitoring the composition of the off-gas, as well as the salt itself, is important for monitoring reactor performance, including burnup, corrosion, and the concentration of impurities. Tritium is of concern for MSRs because it will be produced from the irradiation of key salt constituents, including Li and Be. LIBS offers an avenue for in situ salt and off-gas monitoring by firing a laser onto or into the sample stream to generate a plasma. The plasma light can be monitored to measure an elemental fingerprint of the sample. Extending this analysis to include isotopic ratios offers a critical expansion of the in situ monitoring capabilities being developed. This study demonstrates the expansion of Oak Ridge National Laboratory’s LIBS capabilities to monitor isotopes and shows how simple calibrations may provide rapid semiquantitative models.
07 ISOTOPE AND RADIATION SOURCES↗