Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Plastic deformation mechanism of calcium-silicate hydrates determined by deviatoric-stress Raman spectroscopy

Highlights: • C-(A-)S-H samples under stress were characterized at the bond and grain level. • Small angle scattering showed that 720 MPa reduced grain thickness by 30%. • In-situ Raman showed that cross-linked C-A-S-H slips along its intralayer. • However, in-situ Raman showed that C-S-H slips along the interlayer. • In-situ Raman also showed a growth in CaCO{sub 3}, indicating fracture in both samples. Creep of the cement matrix affects the structural stability of concrete. In Portland cements, the creep is largely controlled by the binding phase calcium-(aluminum-)silicate-hydrate, or C-(A-)S-H. This phase has a lamellar structure and under deviatoric stress aligns its c-axis with the principal stress. However, the limiting resistance to this reorientation is unknown at the nanocrystalline level. Small-angle X-ray scattering shows that the lamellae thickness decreases under 100's MPa deviatoric stress. Deviatoric stress Raman spectroscopy shows that there are two ways that this break-up can occur. If the material's silicate chains are cross-linked, then strain in SiO bonds does not increase above certain stresses, indicating a relaxation adjacent to the SiO bond. If the chains are not cross-linked, then the silicate chains are broken up by rastering against each other, introducing defects. These results show that the plastic deformation of C-(A-)S-H is relevant for Portland cement creep.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Experimental and Numerical Characterization of High Temperature Deformation Behavior of 347H Stainless Steel

This study investigates how temperature affects the plasticity and thermal creep behavior of 347H stainless steel under uniaxial tension. The research combined experimental testing with advanced computational modeling. Two types of experiments were conducted: uniaxial tensile tests at temperatures from 100°C to 750°C using strain rates of ~10⁻⁴ s⁻¹, and creep tests at temperatures between 600°C and 750°C under various stress levels. These experimental results were used to develop and validate a new integrated mechanistic model that can predict material behavior under any loading condition while accounting for both stress and temperature effects. The model was implemented using a polycrystalline microstructure simulation framework based on elasto-viscoplastic Fast Fourier Transform (EVPFFT). It incorporates three key deformation mechanisms: thermally activated dislocation glide, dislocation climb, and vacancy diffusional creep. The model accounts for internal stress distribution within single crystals and considers how precipitates and solute atoms (both interstitial and substitutional) affect dislocation movement. After validation against experimental data, the model was used to generate Ashby-Weertman deformation mechanism maps for 347H steel, providing new insights into how microstructure influences the activation of different creep mechanisms.

Joy, Jobin K.↗
DOE OSTI2024

Experimental Observation of a New Attenuation Mechanism in hcp ‐Metals That May Operate in the Earth's Inner Core

Abstract Seismic observations show the Earth's inner core has significant and unexplained variation in seismic attenuation with position, depth and direction. Interpreting these observations is difficult without knowledge of the visco‐ or anelastic dissipation processes active in iron under inner core conditions. Here, a previously unconsidered attenuation mechanism is observed in zinc, a low pressure analog ofhcp‐iron, during small strain sinusoidal deformation experiments. The experiments were performed in a deformation‐DIA combined with X‐radiography, at seismic frequencies (∼0.003–0.1 Hz), high pressure and temperatures up to ∼80% of melting temperature. Significant dissipation (0.077 ≤ Q −1 (ω) ≤ 0.488) is observed along with frequency dependent softening of zinc's Young's modulus and an extremely small activation energy for creep (⩽7 kJ mol −1 ). In addition, during sinusoidal deformation the original microstructure is replaced by one with a reduced dislocation density and small, uniform, grain size. This combination of behavior collectively reflects a mode of deformation called “internal stress superplasticity”; this deformation mechanism is unique to anisotropic materials and activated by cyclic loading generating large internal stresses. Here we observe a new form of internal stress superplasticity, which we name as “elastic strain mismatch superplasticity.” In it the large stresses are caused by the compressional anisotropy. If this mechanism is also active inhcp‐iron and the Earth's inner‐core it will be a contributor to inner‐core observed seismic attenuation and constrain the maximum inner‐core grain‐size to ≲10 km.

Geochemistry & Geophysics↗
DOE OSTI2021

Development of High-Performance Ni-base Alloys for Gas Turbine Wheels Using a Coprecipitation Approach (Final Technical Report)

In this project, a synergistic approach involving experiments informed by modelling was used to develop γ'/γ'' coprecipitation-strengthened Ni-base superalloys for land-based gas turbine wheels. In thick sections of such turbine wheels, the slow cooling rate normally observed, as well as variations in cooling rate could potentially result in drastically inhomogeneous and coarsened microstructure. Thus, ten alloy compositions were selected based on coprecipitation and sluggish γ’ growth and coarsening during three iterations of alloy development, assisted by extensive CALPHAD modeling. Phase equilibrium calculations, informed by the characterization of early alloys, were successful in predicting suitable aging treatments to obtain bimodal coprecipitate distribution in several alloys. These aging treatments were applied to the subsequent round of alloys and the resulting microstructures were characterized in detail. Two different cooling rates were used during each of these heat treatments to simulate the range of cooling rates observed in a thick section forging. The microstructures were used to calibrate a multi-phase field model (MPF), which was used to study the formation mechanisms of various coprecipitate morphologies observed in the experiments. Following this, the most promising alloys in each round were selected and studied using high temperature tensile and creep tests. Considering that a slower cooling rate would lead to a strength debit, while a faster cooling rate might lead to a decline in creep rupture life of a full-scale wheel, tensile tests were carried out for slower cooled samples, while creep tests were carried out for faster cooled samples. The deformation microstructures were then characterized using advanced characterization techniques such as Diffraction Contrast-Scanning Transmission Electron Microscopy (DC-STEM) and Electron Channeling Contrast Imaging (ECCI). Further, a mean-field creep model was developed and calibrated using these experimental findings to predict long-term creep behavior of these coprecipitation-strengthened alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Creep in multi-principal element materials –– A review

The ongoing push towards enhanced energy efficiency and reduced emissions has necessitated the creation of materials with superior performance, especially under extreme conditions. Modern industries, such as aerospace, energy production, and nuclear power, rely heavily on materials that can withstand elevated temperatures without compromising structural integrity. At these heightened temperatures, materials, even when subjected to mechanical stresses well below their yield strength, may experience slow deformation leading to eventual rupture — a phenomenon known as creep. With the expansive design space that comes with the high entropy concept and their reported excellent high temperature strength, multi-principal element materials (MPEMs) have attracted interest in the scientific community for high-temperature applications. Here, this review offers a comprehensive examination of existing studies on creep in MPEMs, which includes multi-principal element−alloys, −bulk metallic glasses, −ceramics, and −superalloys, comparing published findings on MPEMs with pure elements, traditional alloys, bulk metallic glasses, and superalloys. The sub-topics covered include a comparison among different creep-testing methods, creep mechanisms, creep exponents, creep strain rates, activation volume, and creep-activation energy. Modeling efforts for predicting creep behavior of MPEMs are also reviewed. Methods for improving creep resistance by performing heat treatments and/or modifying microstructures are discussed. Overall, the current state of MPEMs has not yet surpassed the creep performance of commercial alloys. Finally, directions for future efforts are suggested, such as experimenting in various controlled environments, expanding the number of compositions tested, exploring advanced manufacturing techniques, and using machine-learning to predict creep properties based on compositions and microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Periodic training of creeping solids

Significance It is well appreciated that many disordered materials deform their shape irreversibly (plastically) under an external load (e.g., memory foam). Here, we show that this plasticity can be exploited to train materials to develop novel elastic responses by straining them periodically. By applying different periodic strains to a common viscoelastic material, we are able to design a number of different responses. These include a maximally negative Poisson’s ratio, bistable behavior, and nonlocal bond-specific responses. In contrast to computer-aided design, we rely on plasticity to self-organize the system in response to local stresses. This approach shows promise to achieve an unprecedented control over behavior at large strains well beyond the linear-response regime.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Step-loaded creep testing of Zircaloy-4 cladding at higher temperatures in the α-phase

A refined understanding of zirconium-based cladding thermomechanical performance during rapid transients is essential for enhancing the safety and operation of light-water reactors. Traditional models for zirconium alloys under accident conditions generally assume that creep dominates fuel cladding performance. Here, these historic models have largely remained unchanged and serve as the basis for safety criteria development. As the U.S. nuclear industry pursues higher burnup levels, the increased release of fission gases during transients raises the risk of cladding failure in the low-temperature hcp α-phase, making the fidelity of these models of greater importance. Creep testing was conducted from 550–700°C with 25–120 MPa applied hoop stresses to investigate Zircaloy-4 deformation at accident-relevant temperatures in the α-phase. Step-loading was employed to capture creep behavior across a wide stress range from a single sample. The stress-strain rate data at higher temperatures (650 and 700°C) were well-described by isotropic versions of the Erbacher and Kaddour models, while the lower temperature data (550 and 600°C) were underpredicted by both anisotropic and isotropic model variants. Greater strain rates during the initial loading step at 650 and 700°C were attributed to recrystallization and grain growth of sub-micron crystallites. Yet, texture analysis revealed the basal split texture remained after testing. These observations produced results suggesting Zircaloy-4 claddings experience higher creep rates across the α-phase than previously thought, possibly related to dynamic anisotropy due to temperature dependent activation of deformation mechanisms, effects of biaxial loading, and variation in material condition between the current testing used in previous model development.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additively manufactured polymer composites for heat exchanger applications: evaluation of critical thermophysical properties

Polymeric heat exchangers (PHXs) have been used in applications involving weight restrictions, chemical compatibility, and fouling issues. Additive manufacturing (AM) or 3D printing provide new solutions to previously inaccessible combinations of properties and geometries. There are some advancements in the PHXs by AM; however, the process and the properties of materials still need further investigation to improve the overall performance. In this study, additively manufactured polyethylene terephthalate glycol (PETG) composites reinforced with graphite and pitch-based carbon fibers were evaluated for their potential application as PHXs. The thermal conductivity, volumetric heat capacity, coefficient of thermal expansion, creep behavior, and long-term performance were studied in detail. Our results reveal that the composites have an anisotropic thermal conductivity. The thermal conductivity along the printing direction is higher than the layer building direction due to the shear-induced alignment of the fillers. The printed composites achieve good thermal stability with 80% lower CTE at room temperature than neat PETG. Creep tests suggest the creep and creep recovery were highly temperature-dependent, and the deformation can be recovered when the temperature is below glass transition. These results suggest additive manufactured composites be potentially used for heat exchanger applications at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dislocation interactions in olivine control postseismic creep of the upper mantle

Changes in stress applied to mantle rocks, such as those imposed by earthquakes, commonly induce a period of transient creep, which is often modelled based on stress transfer among slip systems due to grain interactions. However, recent experiments have demonstrated that the accumulation of stresses among dislocations is the dominant cause of strain hardening in olivine at temperatures ≤600 °C, raising the question of whether the same process contributes to transient creep at higher temperatures. Here, we demonstrate that olivine samples deformed at 25 °C or 1150–1250 °C both preserve stress heterogeneities of ~1 GPa that are imparted by dislocations and have correlation lengths of ~1 μm. The similar stress distributions formed at these different temperatures indicate that accumulation of stresses among dislocations also provides a contribution to transient creep at high temperatures. The results motivate a new generation of models that capture these intragranular processes and may refine predictions of evolving mantle viscosity over the earthquake cycle.

58 GEOSCIENCES↗
DOE OSTI2025

High-temperature nanoindentation creep studies on castable and sintered nanostructured low-activation ferritic-martensitic alloys

In this article, we present the creep characteristics of two reduced activation ferritic-martensitic steels of identical starting compositions formed by different fabrication routes: a nanostructured ferritic alloy commonly referred to as a castable nanostructured alloy (CNA) and a sintered nanostructured alloy (SNA) variant. Through a series of nanoindentation experiments spanning a temperature range of 25 °C to 650 °C, with a maximum load of 100 mN, we find creep behaviors in the cast and sintered materials to be remarkably similar. The creep stress exponent (n) for CNA and SNA were found to be in the range of 8–35 and the activation volume was ∼14–42b 3 , underscoring a dominance of dislocation-mediated mechanisms in both alloys. Notably, we observed a decline in the creep stress exponent with increasing temperature, attributable to the heightened influence of thermally activated dislocations. This phenomenon suggests a potential transition in the deformation mechanism towards a thermally activated dislocation climb process, significantly impacting the observed creep behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain-boundary θ-Al 2 Cu precipitates on tensile and compressive creep properties of cast Al–Cu–Mn–Zr alloys

Tensile and compressive creep tests were performed at 300 °C on high-temperature Al–Cu–Mn–Zr (ACMZ) alloys with 6 wt% Cu (6Cu) and 9 wt% Cu (9Cu) to evaluate the effect on creep properties of micron-size θ-Al 2 Cu intergranular precipitates. For compressive creep, the increased volume fraction of θ-precipitates at grain boundaries (from ~0.7% in 6Cu to ~ 6% in 9Cu) does not affect deformation rates across the investigated stress range of 15–110 MPa, consistent with creep being controlled by submicron θ'-Al 2 Cu precipitates within grains, whose size and fractions are the same in both alloys. In contrast, for tensile creep, 9Cu creeps faster than 6Cu at stresses above 20 MPa, and this difference increases with the stress level. Additionally, this discrepancy between tensile and compressive creep behavior is explained by cavitation during tensile creep, which is favored by higher volume fraction and larger size of intergranular θ precipitates in 9Cu. Conversely, larger precipitates impede cavity linkage resulting in improved creep ductility of 9Cu as compared to 6Cu at 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

From Well Log to Formation Model: A Novel Laboratory Calibrated Methodology with Demonstration

This work demonstrates how the characterization and modeling of both elastic and creep properties are essential to describe zones in layered rock formations as either low-stress targets for stimulation or high-stress barriers to fracture growth. Prediction of fracture height is critical for designing stimulation operations in oil and gas wells. Ideally, fractures are placed in target zones which will produce hydrocarbons and should not propagate into zones expected to be unproductive or to produce unwanted fluids such as water which in turn must be treated and/or disposed. The essential task in designing stimulation plans is predicting which zones have low horizontal stresses and which will be high-stress barriers to fracture growth. Despite this importance, there are gaps in current knowledge and a complete workflow from laboratory characterization to a finite element model which includes time dependent rock deformation is required. While the research and methodology presented here also have application to CO 2or hydrogen storage, wastewater injection, and geothermal applications, the focus will be on hydrocarbon extraction. This thesis presents the results of a characterization-to-prediction workflow for the Caney shale, which is an emerging hydrocarbon resource in Oklahoma, USA. It begins with an investigation to enable critical evaluation of the Caney zonation into nominally “brittle” and “ductile” zones based on properties observed from well logs. It shows none of the zones are consistently “brittle” or “ductile” mechanical behavior based on the variety of definitions of these terms. However, the nominally ductile zones are weaker and more prone to creep. A laboratory investigation of samples including strength, elastic, and creep properties, is then used in a finite element model of stress evolution. The model includes both elastic deformation and viscoplastic creep. Results predict the least creep-prone layers to have the lowest horizontal stresses, therefore comprising hydraulic fracturing targets. The most creep-prone layers attain a horizontal stress similar to the vertical stress and therefore are predicted to be high stress barriers to hydraulic fracture stimulation. In addition to defining stimulation target intervals, the model shows how as tectonic strain rate increases, there is a transition from creep-dominated stresses to stresses dominated by elasticity.

Benge, Margaret↗
DOE OSTI2022

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Tensile and compressive creep properties of a quaternary Al-Cu-Mn-Zr (ACMZ) alloy and its commercial counterpart (Al-Cu-Mn-Zr with Ni, Co and Sb additions, RR350) are investigated at 300°C. At low stresses up to 30 MPa where diffusional creep dominates, creep resistance is the same in tension and compression and RR350 deforms more slowly than ACMZ, consistent with RR350 alloy's larger linear fraction of intergranular precipitates (Al7Cu2(NiFe) and Al9FeNi for RR350 vs. θ-Al2Cu for ACMZ) and a reduced fraction of precipitate-free zones near grain boundaries. At stresses between 30 and 80 MPa, dislocation creep with a stress exponent n ~ 3 becomes rate-limiting in compression, which is expected to be controlled by θ' precipitates within the grain bulk. By contrast, in tension, enhanced creep rate and higher apparent stress exponents are measured, consistent with cavitation at intergranular precipitates becoming increasingly dominant as the stress increases. In the dislocation creep regime, RR350 alloy is again more creep resistant than ACMZ alloy, which is related to three mechanisms (i) a reduced fraction of softer precipitate-free zones, (ii) more effective load transfer to intergranular precipitates, and (iii) reduced cavitation. A model for cavitation is applied to calculate tensile creep rates from compressive creep rates and the model successfully predicts the improved tensile creep resistance of the RR350 alloy. Overall, the present investigation underscores the importance of intergranular grain boundary precipitates, in addition to strengthening θ' precipitates, in enhancing the creep resistance of Al-Cu alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bridging microscopic dynamics and rheology in the yielding of charged colloidal suspensions

The yielding of soft materials is critical to many natural and industrial processes, yet experimental insights into microscopic aspects of yielding are limited. This study combines angle X-ray scattering, X-ray photon correlation spectroscopy, and in situ rheology (Rheo-SAXS-XPCS) with fast lubrication dynamics simulations to examine how interparticle interactions influence yielding in charged colloidal suspensions. By tuning attraction through salt addition, we compare repulsive and attractive systems under deformation. Repulsive suspensions yield uniformly with Andrade-like creep and minimal structural change. In contrast, attractive suspensions show complex behaviors, including shear banding, delayed yielding, and resolidification, governed by transient dynamics at shear band interfaces. These results directly link microscopic particle dynamics to macroscopic flow and demonstrate how interaction potentials control rheological behavior. This work offers a framework for designing soft materials with tailored properties for applications in coatings, food processing, drug delivery, and other technologies requiring precise mechanical control.

Molecular Dynamics Simulation↗
DOE OSTI2026

Process control-enabled mitigation of microstructural and plastic heterogeneities in additively manufactured Grade 91 steel

Synergizing wire arc-directed energy deposition (WA-DED) additive manufacturing (AM) with particle-strengthened creep strength-enhanced ferritic (CSEF) steels enables fabrication and repair of critical power-plant components. Investigations focused on fusion-welded particle-strengthened CSEF steels, such as Grade 91 steel, have linked microstructurally heterogeneous regions—forming due to heat affected zones (HAZ)—with premature failure during elevated temperature service. Fusion-based AM, including WA-DED, likewise generates microstructurally and plastically heterogeneous regions due to spatiotemporally varying thermokinetics during deposition. However, works investigating such microstructural heterogeneities, their implications for mechanical behavior, and strategies to mitigate their formation remain scarce. This work identifies microstructurally and plastically heterogeneous regions within the WA-DED-processed Grade 91 steel. Spatial microhardness variations in the as-fabricated specimen correlate with the variation in the attributes of grain, martensitic microstructure, and precipitates across the fusion zone and HAZ. Digital image correlation-enabled tensile tests performed at 500 °C revealed pronounced deformation localization and a wave-like strain distribution, with wavelength close to the melt pool depth, indicating susceptibility of the as-fabricated components to premature creep failure. Such heterogeneity in microstructural and mechanical behavior was attributed to recurring solid-state phase transformations. Subsequently, an interlayer temperature control strategy was implemented, wherein maintaining interlayer temperature above the martensitic start temperature mitigated the heterogeneous microstructural and plastic response in the as-fabricated condition. Findings open pathways to achieving deformation-localization- and creep-resistant microstructures in WA-DED fabricated particle-strengthened CSEF steel components, reducing reliance on post-welding heat treatments—conventionally required to enhance creep resistance—and enabling on-demand, short lead-time fabrication of next-generation power-plant components.

Heat affected zones↗
DOE OSTI2023

Data Driven Approach to Dislocation-Based Plasticity Models of Face-Centered Cubic Metals

Dislocation dynamics controls plastic deformation, mechanical strength, and failure of crystalline materials. It also governs fatigue resistance under cyclic loading, creep resistance at elevated-temperature, and radiation resistance for reactor applications. There is a compelling need for understanding fundamental dislocation mechanisms for deformation because virtually all structural metals used in energy systems are fabricated to desired forms and shapes by deformation processes. To date, the most outstanding problem in a physics-based multiscale model of crystal plasticity is the lack of quantitative connections between continuum plasticity (CP) models with the lower scale dislocation models. As a result, existing CP models used in engineering applications are still phenomenological, while evidence continues to mount that they can make inaccurate predictions under realistically complex scenarios. This project takes advantage of the recent advances in high-performance discrete dislocation dynamics (DDD) simulations and data science approaches to establish the first fully connected multiscale plasticity model for pure face-centered cubic (FCC) single crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microscale Mechanical‐Chemical Modeling of Granular Salt: Insights for Creep

Abstract Microscale numerical modeling is potentially an effective approach for understanding salt creep, but it is quite challenging because natural salt grain boundaries can have complex and evolving geometry, and because contacts between these deformable salt mineral grains are dynamic as a result of compaction, chemical reaction, fluid flow, and heat transfer. In this study, we have overcome these challenges and developed a new microscale mechanical‐chemical (MC) model to analyze creep of salt at the microscale, accounting for coupled deformation, dynamic contacts, and chemical reaction in granular systems with realistic geometric representations. The MC model was realized by linking a new microscale mechanical code based on the numerical manifold method (NMM) to a reactive transport code named Crunch. We simulated the processes of reorganization of the salt grains, microfracturing, and pressure solution that contribute to creep at larger scales. Based on this first quantitative microscale model, we found that sharp corners of mineral grains can dominate the contact dynamics, microfracturing, and pressure solution when salt is compacted, thus governing the structural changes and porosity loss of the system. We found that pressure solution, which preferentially dissolves sharp corners and edges, can lead to relatively high porosity loss in the system, thus playing an important role in the creep of salt. Our analysis shows that the dynamic changes of salt granular systems involving grain relocation and pressure solution can occur repeatedly and continuously, thus contributing to longer‐term creep of salt at larger scales.

58 GEOSCIENCES↗
DOE OSTI2025

Development of Predictive Model for Accurate Rupture Time from Multi-Axial Creep in Alloy 709 with Physics-Based Simulations

A physics-based model is developed to predict multiaxial creep behavior in Alloy 709 (A709), an advanced austenitic stainless steel intended for high-temperature applications such as Sodium Fast Reactors (SFRs). Compared to conventional stainless steels like 316H, A709 offers superior high-temperature performance; however, comprehensive data on its multiaxial creep response remain limited. To address this gap, a crystal plasticity finite element (CPFE) framework is used to simulate the deformation and failure mechanisms of A709 under multiaxial loading conditions. The model incorporates an extended Hu-Cocks dislocation creep formulation that accounts for precipitation effects, along with the Sham–Needleman model to capture grain boundary cavitation-driven failure. These advanced constitutive models enable a detailed understanding of the interplay between microstructural evolution and macroscopic creep response. Furthermore, the study evaluates the predictive accuracy of various effective stress measures in estimating creep rupture life, leveraging simulated multiaxial creep data. The findings provide critical insights into the applicability of different stress measures for engineering design and life prediction of A709 components operating under complex loading conditions. This work contributes to improving the reliability of high-temperature structural components by advancing predictive modeling capabilities for advanced austenitic steels.

Alloy 709↗