Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cruise control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

NASA High-Reynolds Number Circulation Control Research - Overview of CFD and Planned Experiments

A new capability to test active flow control concepts and propulsion simulations at high Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center is being developed. This technique is focused on the use of semi-span models due to their increased model size and relative ease of routing high-pressure air to the model. A new dual flow-path high-pressure air delivery station has been designed, along with a new high performance transonic sem -si pan wing model. The modular wind tunnel model is designed for testing circulation control concepts at both transonic cruise and low-speed high-lift conditions. The ability of the model to test other active flow control techniques will be highlighted. In addition, a new higher capacity semi-span force and moment wind tunnel balance has been completed and calibrated to enable testing at transonic conditions.

Milholen, W. E., II↗
NASA NTRS1971

A progress report on the development of an augmentor wing jet STOL research aircraft.

The development of the aircraft has progressed to the point where the design of the modifications to the de Havilland C-8A Buffalo is complete and the engines are being tested. The predicted performance shows that the aircraft will be able to take off and land in less than 1500 ft. Simulation studies indicate that the handling qualities of the aircraft, with stability augmentation, will be acceptable for STOL research missions. Special techniques were required, however, for flight path control and transition from cruise to landing configuration .

Quigley, H. C.↗
NASA NTRS1977

Wind-tunnel results of the aerodynamic characteristics of a 1/8-scale model of a twin engine short-haul transport

A wind tunnel test was conducted in the Langley V/STOL tunnel to define the aerodynamic characteristics of a 1/8-scale twin-engine short haul transport. The model was tested in both the cruise and approach configurations with various control surfaces deflected. Data were obtained out of ground effect for the cruise configuration and both in and out of ground effect for the approach configuration. These data are intended to be a reference point to begin the analysis of the flight characteristics of the NASA terminal configured vehicle (TCV) and are presented without analysis.

Paulson, J. W., Jr.↗
NASA NTRS2020

Thermal Architecture of A Conceptual Mars Sample Return Lander during Cruise and on Mars

A Pre-Project team is currently studying a conceptual Mars Sample Return (MSR) architecture that would return samples collected by Mars 2020 to Earth. The basic architecture comprises of acquisition of these samples using a sample retrieval lander (SRL), which also would also house the Mars Ascent Vehicle (MAV) and Sample Fetch Rover (SFR). The MAV would put the orbiting sample container (OS) in a Martian orbit, which would then rendezvous with an Earth return orbiter (ERO) and be sent to Earth. This paper focuses on the SRL portion of the potential MSR campaign. The thermal architecture of this mission during cruise to Mars presents several challenges that pertain to the thermal control of the spacecraft and the lander/MAV/rover throughout cruise under varying thermal environments & operating conditions. Additionally, the control of these systems within their allowable operating temperature limits on the Martian surface is very challenging because of the large fluctuations in the environment, operating conditions and limited electrical power and energy availability. This paper will describe the thermal architecture for a potential SRL mission, the key thermal requirements and interfaces.It should be noted that the decision to implement MSR will not be finalized until NASA’s completion of the National Environmental Policy Act (NEPA) process. This document is being made available for information purposes only.

Nicholas, Austin↗
NASA NTRS1974

Mariner Mars 1971 attitude control subsystem

The Mariner Mars 1971 attitude control subsystem (ACS) is discussed. It is comprised of a sun sensor set, a Canopus tracker, an inertial reference unit, two cold gas reaction control assemblies, two rocket engine gimbal actuators, and an attitude control electronics unit. The subsystem has the following eight operating modes: (1) launch, (2) sun acquisition, (3) roll search, (4) celestial cruise, (5) all-axes inertial, (6) roll inertial, (7) commanded turn, and (8) thrust vector control. In the celestial cruise mode, the position control is held to plus or minus 0.25 deg. Commanded turn rates are plus or minus 0.18 deg/s. The attitude control logic in conjunction with command inputs from other spacecraft subsystems establishes the ACS operating mode. The logic utilizes Sun and Canopus acquisition signals generated within the ACS to perform automatic mode switching so that dependence of ground control is minimized when operating in the sun acquisition, roll search, and celestial cruise modes. The total ACS weight is 65.7 lb, and includes 5.4 lb of nitrogen gas. Total power requirements vary from 9 W for the celestial cruise mode to 54 W for the commanded turn mode.

Edmunds, R. S.↗
NASA NTRS1995

A concept for adaptive performance optimization on commercial transport aircraft

An adaptive control method is presented for the minimization of drag during flight for transport aircraft. The minimization of drag is achieved by taking advantage of the redundant control capability available in the pitch axis, with the horizontal tail used as the primary surface and symmetric deflection of the ailerons and cruise flaps used as additional controls. The additional control surfaces are excited with sinusoidal signals, while the altitude and velocity loops are closed with guidance and control laws. A model of the throttle response as a function of the additional control surfaces is formulated and the parameters in the model are estimated from the sensor measurements using a least squares estimation method. The estimated model is used to determine the minimum drag positions of the control surfaces. The method is presented for the optimization of one and two additional control surfaces. The adaptive control method is extended to optimize rate of climb with the throttle fixed. Simulations that include realistic disturbances are presented, as well as the results of a Monte Carlo simulation analysis that shows the effects of changing the disturbance environment and the excitation signal parameters.

Jackson, Michael R.↗
NASA NTRS1998

Controller Strategies for Managing Air Traffic in High Altitude Arrival Sectors

Substantial increases in the volume of air traffic in the National Airspace System (NAS) are forecast for the next decade, with the number of passengers travelling on U.S. airlines expected to increase by as much as 60%. This increased demand on system capacity will be accompanied by increases in traffic complexity as air traffic service providers routinely accommodate user preferred routing requests. Changes to the NAS to meet these new demands are currently underway, including development of new decision support tools to aid controllers in monitoring and managing air traffic, and increased air-to-air and air-to-ground information exchange. Changes in roles and responsibilities of pilots and controllers in flight path management will accompany these changes in traffic patterns and information technology, however the ultimate responsibility for maintaining aircraft separation will remain with the air traffic controller. A thorough understanding of the methods controllers use to manage air traffic will help ensure that changes to the NAS are implemented in a way that maintains the controller's ability to separate aircraft as the system evolves. This presentation describes the strategies controllers use today to manage arrival traffic in its descent from cruise altitude to the Terminal Radar Approach Control (TRACON) boundary. Factors that increase the complexity of this task include the presence of overflight traffic, varying aircraft performance characteristics, winds aloft, ground speed variations with altitude, the need to merge arrival traffic into a single stream, and, when arrival traffic exceeds airport runway capacity, the added task of metering flow into the TRACON. Because of the limited information available to controllers to manage arrival traffic, their strategies are often driven by the need to reduce the task's complexity, which can result in de-optimized flight paths for individual aircraft (e.g., sub-optimal descent or speed profiles). Understanding these strategies and the cognitive demands that drive them will support a safe transition to a NAS that relies on enhanced technologies. In addition, it could enable system developers to identify opportunities for new automation-based procedures or information displays that could reduce the controller's workload and increase operational efficiency.

Smith, Nancy↗
NASA NTRS1973

Automatic control in planetary exploration in the 1980s

Based on an examination of the planetary missions in the 1980s and their related objectives, a broad assessment of the automatic control capabilities required for these missions is presented. The ten outer-planet, terrestrial-planet, and small-body missions considered involve various operations encompassing a complex series of modes including cruise, maneuver, and powered flight control. In addition to routine navigation and attitude control, onboard control is required to point scientific instruments and antennas with respect to the vehicle and to maneuver the spacecraft in time-constrained or hazardous environments. These 1980 missions aimed at exploring new areas of the solar system will be more demanding. New design philosophies and increased performance capabilities will be required to meet the constraints imposed by science requirements and mission-cost effectiveness.

Moore, J. W.↗
NASA NTRS1976

Effects of atmospheric conditions on the operating characteristics of supersonic cruise aircraft

Since for maximum range a supersonic transport must cruise near its maximum Mach number, accurate flight control is needed, especially when severe atmospheric transients are encountered. This paper describes atmospheric transients that have been encountered by the XB-70, YF-12, and Concorde aircraft during supersonic flights and the ensuing responses of the aircraft propulsion and flight control systems. It was found that atmospheric conditions affected these supersonic cruise vehicles in much the same way, with minor differences according to the type of propulsion and flight control system. Onboard sensors are sufficiently accurate to provide data on the atmosphere, including turbulence over the route, that are accurate enough for entry in the climatic record and for use as inputs to the control systems. Nominal atmospheric transients can be satisfactorily controlled, but some problems remain for extreme cases.

Schweikhard, W. G.↗
NASA NTRS2002

Controlled breaks as a fatigue countermeasure on the flight deck

BACKGROUND: A major challenge for flight crews is the need to maintain vigilance during long, highly automated nighttime flights. No system currently exists to assist in managing alertness, and countermeasure options are limited. Surveys reveal many pilots use breaks as an in-flight countermeasure, but there have been no controlled studies of their effectiveness. HYPOTHESIS: We hypothesized that brief, regular breaks could improve alertness and performance during an overnight flight. METHOD: A 6-h, uneventful, nighttime flight in a Boeing 747-400 flight simulator was flown by fourteen two-man crews. The 14 subjects in the treatment group received 5 short breaks spaced hourly during cruise; the 14 subjects in the control group received 1 break in the middle of cruise. Continuous EEG/EOG, subjective sleepiness, and psychomotor vigilance performance data were collected. RESULTS: During the latter part of the night, the treatment group showed significant reductions for 15 min post-break in slow eye movements, theta-band activity, and unintended sleep episodes compared with the control group. The treatment group reported significantly greater subjective alertness for up to 25 min post-break, with strongest effects near the time of the circadian trough. There was no evidence of objective vigilance performance improvement at 15-25 min post-break, with expected performance deterioration occurring due to elevated sleep drive and circadian time. CONCLUSIONS: The physiological and subjective data indicate the breaks reduced nighttime sleepiness for at least 15 min post-break and may have masked sleepiness for up to 25 min, suggesting the potential usefulness of short-duration breaks as an in-flight fatigue countermeasure.

Non-NASA Center↗
NASA NTRS1975

Mechanically coupled lift fan propulsion and control for multimission V/STOL aircraft

A two-engine, three-fan V/STOL airplane was designed to fulfill naval operational missions. Use of interconnected variable pitch fans led to a good balance between the requirements for high thrust and responsive control at low speed, and efficient thrust at cruise speeds. Engine-out requirements, integration of propulsion and aerodynamic controls, and the propulsion installation were the major factors influencing the configuration. An airplane with a multimission capability from both vertical and short takeoff was conceived.

Zabinsky, J. M.↗
NASA NTRS1992

Supersonic HLFC: Potential benefits and technology development requirements

The viewgraphs and discussion of the potential benefits and technology development requirements of supersonic Hybrid Laminar Flow Control (HLFC) are reviewed. For the last three years, Boeing has performed studies on the application of laminar flow control to High Speed Civil Transport (HSCT) configurations. Large potential net benefits were identified for laminar flow control, even after accounting for the significant implementation penalties. However, the technical risks are high at this time, and an early, aggressive technology development program is required if laminar flow control (LFC) is to be incorporated in a year 2005 HSCT program. The benefits and required development effort are addressed. Of all the aerodynamic advances that are being considered for the HSCT, LFC has the largest potential for improving the supersonic lift drag ratio of a given configuration. The work accomplished to date, sponsored by NASA Langley, is summarized. This work includes studies on HLFC application to HSCT, cruise HLFC/low speed boundary layer control (BLC) compatibility, and impact of M 0.9 HLFC and high lift BLC. Requirements for production committments are listed. The need for a HSCT-HLFC Risk Reduction Program is addressed. Supersonic HLFC development planning and future applications are addressed. Laminar flow/high-lift integration is addressed.

Neumann, Frank↗
NASA NTRS2015

Aerodynamic Load Analysis of a Variable Camber Continuous Trailing Edge Flap System on a Flexible Wing Aircraft

This paper presents an investigative aerodynamic analysis conducted on the novel control surface known as a Variable Camber Continuous Trailing Edge Flap (VCCTEF). The VCCTEF is modeled as a control effector on the NASA Generic Transport Model (GTM) where wing flexibility is considered. Aerodynamic modeling of the aircraft is conducted using vortex-lattice method (VLM), and an aeroelastic model of the aircraft that utilizes a coupled finite-element analysis (FEA) vortex-lattice solution is employed. VLM solutions are used to determine quasi-steady aerodynamic loading over the aeroelastic wing structures with VCCTEF. The load data is used to calculate aerodynamic sensitivities to control surface deployment and is also integrated to determine overall hinge moments. This analysis is conducted for different flight conditions, where control sensitivities compare the VCCTEF effectiveness against conventional control surfaces. Hinge moment results provide insight into aeroelastic wing loads, and worst case hinge moments for the VCCTEF can be estimated. Results show that the VCCTEF offers greater control authority than conventional ailerons at cruise, and nominal flap settings are determined for a low-speed take-off condition where the VCCTEF maintains comparable control effectiveness. Worst case hinge moment values are presented, where for a possible VCCTEF configuration, the stiff wing model demonstrates up to a 5.90 percent increase in flap hinge moment relative to a rigid model, and a reduced stiffness model demonstrates up to an 11.42 percent increase.

Aeroelasticity↗
NASA NTRSDate not supplied

Cruise Propulsion System Thermal Analysis for NASA’s X-57 “Maxwell” Mod II Configuration

The X-57 “Maxwell” is NASA’s flight demonstrator for distributed electric propulsion technologies. The X-57 Mod II configuration is designed to test the electric cruise propulsion system for X-57 and features an electric cruise motor mounted in an integral nacelle on each wing. The electric motors and associated control equipment for X-57 Mod II are air-cooled; therefore, they require adequate cooling airflow to stay within temperature limits in all relevant flight conditions within the operational ambient temperature limits set by the X-57 project. A computational flow analysis was conducted to estimate the internal flow properties of the X-57 Mod II cruise nacelles in three critical flight conditions. These flow properties were then used to determine the boundary conditions for individual component thermal models, which were used to estimate individual component operating temperatures. The results indicated that the low-speed, low-altitude initial takeoff climb during hot day conditions was the sizing condition from a cooling perspective. The analysis found that the cooling flowpaths in the X-57 Mod II cruise nacelles are adequate to provide cooling to all components with the appropriate amount of thermal margin except two of the low-voltage control boards in the cruise motor controller. These components would violate required thermal margins by less than two degrees Celsius in the Project Hot Day reference atmosphere.

Nicholas K Borer↗
NASA NTRS2003

Advances in Pneumatic-Controlled High-Lift Systems Through Pulsed Blowing

Circulation Control technologies have been around for 65 years, and have been successfully demonstrated in laboratories and flight vehicles alike. Yet there are few production aircraft flying today that implement these advances. Circulation Control techniques may have been overlooked due to perceived unfavorable trade offs of mass flow, pitching moment, cruise drag, noise, etc. Improvements in certain aspects of Circulation Control technology are the focus of this paper. This report will describe airfoil and blown high lift concepts that also address cruise drag reduction and reductions in mass flow through the use of pulsed pneumatic blowing on a Coanda surface. Pulsed concepts demonstrate significant reductions in mass flow requirements for Circulation Control, as well as cruise drag concepts that equal or exceed conventional airfoil systems.

Jones, Gregory S.↗