SEARCH · Search NASA

Results for “Cylinder pressure data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Test data from solid propellant plume aerodynamics test program in Ames 6 x 6 foot supersonic wind tunnel (shuttle test FA7) (Ames test 033-66)

The aerodynamic effects of plumes from hot combustion gases in the presence of a transonic external flow field were measured to advance plumes simulation technology, extend a previously acquired data base, and provide data to compare with the effects observed using cold gas plumes. A variety of underexpanded plumes issuing from the base of a strut-mounted ogive-cylinder body were produced by combusting solid propellant gas generators. The gas generator fired in a short-duration mode (200 to 300 msec). Propellants containing 16 percent and 2 percent A1 were used, with chamber pressures from 400 to 1800 psia. Conical nozzles of 15 deg half-angle were tested with area ratios of 4 and 8. Pressures were measured in the gas generator combustion chamber, along the nozzle wall, on the base, and along the body rear exterior. Schlieren photographs were taken for all tests. Test data are presented along with a description of the test setup and procedures.

Hair, L. M.↗

NASA NTRS1984

An evaluation of a parabolized Navier-Stokes (PNS) code for cone-cylinder-flared configurations

A PNS code's capability to predict the onset of laminar and turbulent boundary layer separation, forces, moments, and pressure distributions was investigated. Predictions of incipient separation show good agreement with experimental results. Force and moment calculations were found to agree favorably with experimental data for a wide range of geometries for Mach numbers from 2 to 4 with turbulent boundary layers. Limited comparison of pressure distribution data also showed good agreement. Skin friction and Stanton number calculations are presented to indicate the code's capability to calculate this information and hence, provide a complete data base for attached flow conditions. The sensitivity of these calculations to smoothing and marching parameter variations was examined and found to be acceptable for most design work. The code was found to be suitable to complement or reduce wind tunnel experimentation for the design of this class of configuration with regard to accuracy, cost and usability.

Cottrell, C. J.↗

NASA NTRS1994

Verifying Stiffness Parameters Of Filament-Wound Cylinders

Predicted engineering stiffness parameters of filament-wound composite-material cylinders verified with respect to experimental data, by use of equations developed straightforwardly from applicable formulation of Hooke's law. Equations derived in engineering study of filament-wound rocket-motor cases, also applicable to other cylindrical pressure vessels made of orthotropic materials.

Verderaime, V.↗

NASA NTRS1985

Methods for heat transfer and temperature field analysis of the insulated diesel phase 2 progress report

This report describes work done during Phase 2 of a 3 year program aimed at developing a comprehensive heat transfer and thermal analysis methodology for design analysis of insulated diesel engines. The overall program addresses all the key heat transfer issues: (1) spatially and time-resolved convective and radiative in-cylinder heat transfer, (2) steady-state conduction in the overall structure, and (3) cyclical and load/speed temperature transients in the engine structure. During Phase 2, radiation heat transfer model was developed, which accounts for soot formation and burn up. A methodology was developed for carrying out the multi-dimensional finite-element heat conduction calculations within the framework of thermodynamic cycle codes. Studies were carried out using the integrated methodology to address key issues in low heat rejection engines. A wide ranging design analysis matrix was covered, including a variety of insulation strategies, recovery devices and base engine configurations. A single cylinder Cummins engine was installed at Purdue University, and it was brought to a full operational status. The development of instrumentation was continued, concentrating on radiation heat flux detector, total heat flux probe, and accurate pressure-crank angle data acquisition.

Morel, T.↗

NASA NTRS1991

Sonic boom predictions for three generic models using a solution-adaptive full-potential code

The TranAir full-potential code, which utilizes a solution-adaptive, unstructured Cartesian grid, was used to compute near-field pressure signatures of three generic supersonic configurations: a cone-cylinder, a low aspect ratio rectangular wing, and a delta-wing/body. TranAir pressure signatures are extrapolated to near- and mid-field distances using a quasi-linear extrapolation technique. Results are compared with existing wind tunnel data and, where possible, with extrapolated experimental data and quasi-linear Whitham-method results. In general, the extrapolated TranAir data is in good agreement with experimental and Whitham-method pressure signatures, but peak pressures are slightly under-predicted. It is thought that computed data obtained too near to the model was the main reason for the discrepancies. Flow-field grid structure was also found to be important in obtaining accurate offbody data.

Madson, Michael D.↗

NASA NTRS1994

Sonic boom predictions using a solution-adaptive full-potential code

The TranAir full-potential code, which utilizes a solution-adaptive, unstructured Cartesian grid, was used to compute near-field pressure signatures of three generic geometries: (1) a cone-cylinder; (2) a low aspect ratio rectangular wing; and (3) a delta-wing/body. Pressure signatures computed by TranAir are extrapolated to near- and midfield distances using a quasilinear extrapolation technique. Results are compared with wind-tunnel data and, where possible, with extrapolated wind-tunnel data and Whitham-method results. In general, extrapolated TranAir data is in good agreement with experimental and Whitham-method pressure signatures, but peak pressures are slightly underpredicted. It is felt that data computed too close to the model caused some of the discrepancies. The flowfield grid structure was also found to be an important issue in obtaining accurate off-body data. Results were encouraging enough to proceed with the application of TranAir to conceptual configurations in support of the NASA high speed research program (HSRP).

Madson, Michael D.↗

NASA NTRS1959

Preliminary Study of a Piston Pump for Cryogenic Fluids

Preliminary data are presented covering the performance of a low-speed, five-cylinder piston pump designed for handling boiling hydrogen. This pump was designed for a flow of 55 gallons per minute at 240 rpm with a discharge pressure of 135 pounds per square inch. Tests were made using JP-4 fuel, liquid nitrogen, and liquid hydrogen. Pump delivery and endurance characteristics were satisfactory for the range of operation covered. In connection with the foregoing pump development, the cavitation characteristics of a preliminary visual model, glass-cylinder pump and of a simple reciprocating disk were studied. Subcooling of approximately 0.60 F was obtained from the cavitation produced by reciprocating a disk in boiling nitrogen and in boiling water. The subcooling obtained in a similar manner with liquid hydrogen was somewhat less.

Biermann, Arnold E.↗

NASA NTRS1954

Aerodynamic Characteristics of a Circular Cylinder at Mach Number of 6.86 and Angles of Attack up to 90 Degrees

Pressure-distribution and force tests of a circular cylinder have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.86, a Reynolds number of 129,000 based on diameter, and angles of attack up to 90 degrees. The results are compared with the hypersonic approximation of Grimminger, Williams, and Young and with a simple modification of the Newtonian flow theory. The comparison of experimental results shows that either theory gives adequate general aerodynamic characteristics but that the modified Newtonian theory gives a more accurate prediction of the pressure distribution. The calculated crossflow drag coefficients plotted as a function of crossflow Mach number were found to be in reasonable agreement with similar results obtained from other investigations at lower supersonic Mach numbers. Comparison of the results of this investigation with data obtained at a lower Mach number indicates that the drag coefficient of a cylinder normal to the flow is relatively constant for Mach numbers above about 4.

Penland, Jim A↗

DOE OSTI2023

Final Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing: Development of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer. We have developed a continuum electromechanics model of the microwave resonant cavity transducer performance. The deflection of the membrane is calculated using equations from the theory of plates and shells for deflection of radially constrained thin circular disk under uniform load. The microwave frequency shift is calculated using the equations from the microwave cavity perturbation theory. The transducer model was validated with proof-of-concept experimental data of water flow sensing with a Brass 360 right circular cylinder with 22.2mm diameter and 203µm thick wall. The cavity was excited through a subwavelength hole in TE 011 mode with resonant frequency f ≈ 17.8GHz. Subsequently, we have performed a preliminary proof-of-principle test of flow sensing in high temperature liquid sodium in environment. For this test, we have developed a cylindrical resonator with the same dimensions as for the Brass 360 cavity. The resonator for high temperature liquid sodium test was machined from stainless steel 316 and electroplated with silver on the interior surfaces. We have also developed and insertion probe consisting of a 50cm WR-42 brass waveguide enclosed in a protective SS316 tube. The cavity was excited through a subwavelength hole on the side of the wall of the cylinder in the TE 011 mode with resonant frequency f ≈ 17.8GHz. The liquid sodium setup consists of a cylindrical vessel with a center feed line, where a transducer inserted through the top cap of the vessel measures velocity of the impinging liquid jet. The sodium flow sensing study was performed in a liquid sodium vessel at 340°C temperature and ambient pressure. The flow rate was changed by varying sodium pump power, and a frequency shift of several hundred kHz was observed. The transducer was removed after 70 days of testing. No visual damage was observed, and the electromagnetic response remained the same. As a calibration experiment, we have assembled a water vessel with a center feed, and with dimensions similar to those of the liquid sodium setup. Water flow sensing was performed before and after liquid sodium test. The responses in both cases are similar and agree with COMSOL computer simulations. Because long-term (multi-year) experimental tests of transducer resilience to harsh environment are not practical, we have developed a probabilistic model of creep to estimate transducer resilience to the harsh environment. The probabilistic model considers diffusion creep under the condition of high temperature and low stress, where the stress and temperature are allowed to be random variables with Gaussian distributions. Using the probabilistic model, we estimate inelastic membrane deflections due to creep for several temperature ranges. We conclude that for temperatures less than 650°C, creep has negligible long-term effect on the transducer performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Revisiting the Kinematics of the Cylinder Test

The cylinder expansion experiment is a well-established performance test for condensed explosives that is utilized routinely to determine pressure-energy-volume relationships for detonation products. The modern cylinder test employs optical interferometric techniques to measure velocity, as opposed to older realizations where streak cameras were commonplace. Despite their widespread use, questions sometimes remain as to what kind of data the velocity diagnostics in a cylinder test provide along with how to interpret such measurements and relate them to physical quantities of interest. Here in this study, equations are derived that fully describe the kinematics of the cylinder wall during expansion. These equations are then applied to experimental as well as synthetic data generated via a hydrodynamic simulation in order to verify the mathematical framework developed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1973

NASTRAN static and buckling analysis - comparison with other large-capacity programs

A square plate with clamped edges under a concentrated load was modeled using NASTRAN and ASKA finite element computer programs. Deflections were computed for various width-to-thickness ratios (b/t) of the plate element, and were compared against the classical theory to determine the b/t limitations. A cylinder with simply supported ends was modeled using NASTRAN and STAGS computer programs for buckling analysis. The models were subjected to a uniform radial pressure loading. Several parameters were changed, and the effects of those variations are presented. Utilizing these data, a model which will produce results comparable to published empirical data can be constructed and processed for a minimized cost.

Shah, L. C.↗

NASA NTRS1975

Turbulent wall jet in a coflowing stream

A theoretical investigation was undertaken to develop a relatively simple model of a two-dimensional, turbulent wall jet in a coflowing stream. The incompressible jet flow was modeled by using an integral method which includes turbulent shear stress, entrainment, and heat transfer. The method solves the conservation equations for the average jet flow properties and uses the velocity profile suggested by Escudier and Nicoll to obtain detailed characteristics of the jet on a flat plate. The analytical results compare favorably with experimental data for a range of injection velocities, which demonstrates the usefulness of the theory for estimating jet growth, velocity decay, and wall skin friction. The theory, which was applied to a Coanda jet on a circular cylinder, provided estimates of suction pressures aft of the jet exit that were in close agreement with experimental values.

Campbell, J. F.↗

NASA NTRS1988

A point implicit unstructured grid solver for the Euler and Navier-Stokes equations

An upwind finite element technique that uses cell centered quantities and implicit and/or explicit time marching has been developed for computing hypersonic laminar viscous flows using adaptive unstructured triangular grids. A structured grid of quadrilaterals is laid out near the body surface. For inviscid flows the method is stable at Courant numbers of over 100,000. A first order basic scheme and a higher order flux corrected transport (FCT) scheme have been implemented. This technique has been applied to the problem of predicting type III and IV shock wave interactions on a cylinder, with a view of simulating the pressure and heating rate augmentation caused by an impinging shock on the leading edge of a cowl lip of an engine inlet. The predictions of wall pressure and heating rates compare very well with experimental data. The flow features are very distinctly captured with a sequence of adaptively generated grids. The adaptive mesh generator and the upwind Navier-Stokes solver are combined in a set of programs called LARCNESS, an acronym for Langley Adaptive Remeshing Code and Navier-Stokes Solver.

Thareja, Rajiv R.↗

NASA NTRS1992

Overview of NASA supported Stirling thermodynamic loss research

NASA is funding research to characterize Stirling machine thermodynamic losses. NASA's primary goal is to improve Stirling design codes to support engine development for space and terrestrial power. However, much of the fundamental data is applicable to Stirling cooling and heat pump applications. The research results are reviewed. Much was learned about oscillating flow hydrodynamics, including laminar/turbulent transition, and tabulated data was documented for further analysis. Now, with a better understanding of the oscillating flow field, it is time to begin measuring the effects of oscillating flow and oscillating pressure level on heat transfer in heat exchanger flow passages and in cylinders.

Tew, Roy C.↗

NASA NTRS1992

Overview of NASA supported Stirling thermodynamic loss research

Tew, Roy C.↗

NASA NTRS1973

A study of methods which predict supersonic flow fields from body geometry, distance, and Mach number

A study of seven methods for predicting flow-field pressure signatures from the parameters Mach number, body geometry, and field-path distance has been made. The methods included the method of characteristics, which served as a standard of comparison; a shock-capturing method; three Whitham theory methods; a modified characteristics method; and a bicharacteristics method. Results from each method were also compared with recently obtained wind-tunnel data for a cone-cylinder model at Mach numbers of 2.96 and 4.63 with ratios of radial distance to cone length of 2 and 5. The comparisons at a Mach number of 2.96 showed that signatures from all the methods correlated well with wind-tunnel data and with the signatures predicted by the method of characteristics. At a Mach number of 4.63, however, the agreement between the signatures obtained in the wind tunnel and those predicted by theory varied from good to poor, as did the agreement between the signatures obtained by the method of characteristics and the other six methods. It should be noted that these results and comparisons indicate pressure prediction capabilities only for the near-field flow about bodies of revolution.

Mack, R. J.↗

NASA NTRS1985

RE-1000 free-piston Stirling engine update

A free piston Stirling engine was tested. The tests performed over the past several years on the single cylinder engine were designed to investigate the dynamics of a free piston Stirling engine. The data are intended to be used primarily for computer code validation. The tests designed to investigate the sensitivity of the engine performance to variations in working space pressure, heater and cooler temperatures, regenerator porosity, power piston mass and displacer dynamics were completed. In addition, some data were recorded with alternate working fluids. A novel resonant balance system for the engine was also tested. Some preliminary test results of the tests performed are presented along with an outline of future tests to be run with the engine coupled to a hydraulic output unit. A description of the hydraulic output unit is given.

Schreiber, J. G.↗

NASA NTRS1985

RE-1000 free-piston Stirling engine update

Schreiber, J.↗