Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diameter effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Effect of airstream velocity on mean drop diameters of water sprays produced by pressure and air atomizing nozzles

A scanning radiometer was used to determine the effect of airstream velocity on the mean drop diameter of water sprays produced by pressure atomizing and air atomizing fuel nozzles used in previous combustion studies. Increasing airstream velocity from 23 to 53.4 meters per second reduced the Sauter mean diameter by approximately 50 percent with both types of fuel nozzles. The use of a sonic cup attached to the tip of an air assist nozzle reduced the Sauter mean diameter by approximately 40 percent. Test conditions included airstream velocities of 23 to 53.4 meters per second at 293 K and atmospheric pressure.

Ingebo, R. D.↗

Effect of airstream velocity on mean drop diameters of water sprays produced by pressure and air atomizing nozzles

A scanning radiometer was used to determine the effect of airstream velocity on the mean drop diameter of water sprays produced by pressure atomizing and air atomizing fuel nozzles used in previous combustion studies. Increasing airstream velocity from 23 to 53.4 meters per second reduced the Sauter mean diameter by approximately 50 percent with both types of fuel nozzles. The use of a sonic cup attached to the tip of an air assist nozzle reduced the Sauter mean diameter by approximately 40 percent. Test conditions included airstream velocities of 23 to 53.4 meters per second at 293 K and atmospheric pressure.

Ingebo, R. D.↗

Structural concepts for large solar concentrators

The Sunflower large solar concentrator, developed in the early 1970's, is a salient example of a high-efficiency concentrator. The newly emphasized needs for solar dynamic power on the Space Station and for large, lightweight thermal sources are outlined. Existing concepts for high efficiency reflector surfaces are examined with attention to accuracy needs for concentration rates of 1000 to 3000. Concepts using stiff reflector panels are deemed most likely to exhibit the long-term consistent accuracy necessary for low-orbit operation, particularly for the higher concentration ratios. Quantitative results are shown of the effects of surface errors for various concentration and focal-length diameter ratios. Cost effectiveness is discussed. Principal sources of high cost include the need for various dished panels for paraboloidal reflectors and the expense of ground testing and adjustment. A new configuration is presented addressing both problems, i.e., a deployable Pactruss backup structure with identical panels installed on the structure after deployment in space. Analytical results show that with reasonable pointing errors, this new concept is capable of concentration ratios greater than 2000.

Hedgepeth, John M.↗

Full-Scale Tests of Several Propellers Equipped with Spinners, Cuffs, Airfoil and Round Shanks, and NACA 16-Series Sections, Special Report

Wind-tunnel tests of several propeller, cuff, and spinner combinations were conducted in the 20 foot propeller-research tunnel. Three propellers, which ranged in diameter from 8.4 to 11.25 feet, were tested at the front end of a streamline body incorporating spinners of two diameters. The tests covered a blade angle range from 20 deg to 65 deg. The effect of spinner diameter and propeller cuffs on the characteristics of one propeller was determined. Test were also conducted using a propeller which incorporated aerodynamically good shank sections and using one which incorporated the NACA 16 series sections for the outer 20 percent of the blades. Compressibility effects were not measured, owing to the low testing speeds. The results indicated that a conventional propeller was slightly more efficient when tested in conjunction with a 28 inch diameter spinner than with a 23 inch spinner, and that cuffs increased the efficiency as well as the power absorption characteristics. A propeller having good aerodynamic shanks was found to be definitely superior from the efficiency standpoint to a conventional round-shank propeller with or without cuffs; this propeller would probably be considered structurally impracticable, however. The propeller incorporating the NACA 16 series sections at the tims were found to have a slightly higher efficiency than a conventional propeller; the take-off characteristics appeared to be equally good. The effects noted above probably would be accentuated at helical speeds at which compressibility effects would enter.

Biermann, David↗

Effect of hole geometry and Electric-Discharge Machining (EDM) on airflow rates through small diameter holes in turbine blade material

The effects of two design parameters, electrode diameter and hole angle, and two machine parameters, electrode current and current-on time, on air flow rates through small-diameter (0.257 to 0.462 mm) electric-discharge-machined holes were measured. The holes were machined individually in rows of 14 each through 1.6 mm thick IN-100 strips. The data showed linear increase in air flow rate with increases in electrode cross sectional area and current-on time and little change with changes in hole angle and electrode current. The average flow-rate deviation (from the mean flow rate for a given row) decreased linearly with electrode diameter and increased with hole angle. Burn time and finished hole diameter were also measured.

Hippensteele, S. A.↗

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed to calculate the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases where the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed for calculating the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex-lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases in which the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗

Analytical calculation of thickness versus diameter requirements of silicon solar cells

It may be more cost-effective to produce larger diameter silicon Cz solar cells. However, greater thickness is anticipated to be necessary for larger diameter wafers to withstand wafering, cell processing and handling. No material standard for these dimensional requirements is practical or cost-effective for cell manufacturers. The equations relating wafer thickness and diameter were derived by using fracture mechanics analysis. An analytical model was used as a guideline to estimate thickness versus diameter requirements of silicon solar cells in terms of fracture mechanics parameters.

Chen, C. P.↗

Thermal Inertia of Rocks and Rock Populations

The effective thermal inertia of rock populations on Mars and Earth is derived from a model of effective inertia versus rock diameter. Results allow a parameterization of the effective rock inertia versus rock abundance and bulk and fine component inertia. Additional information is contained in the original extended abstract.

Golombek, M. P.↗

Effects of anisosmotic stress on cardiac muscle cell length, diameter, area, and sarcomere length

The purpose of this study was to examine the effects of anisosmotic stress on adult mammalian cardiac muscle cell (cardiocyte) size. Cardiocyte size and sarcomere length were measured in cardiocytes isolated from 10 normal rats and 10 normal cats. Superfusate osmolarity was decreased from 300 +/- 6 to 130 +/- 5 mosM and increased to 630 +/- 8 mosM. Cardiocyte size and sarcomere length increased progressively when osmolarity was decreased, and there were no significant differences between cat and rat cardiocytes with respect to percent change in cardiocyte area or diameter; however, there were significant differences in cardiocyte length (2.8 +/- 0.3% in cat vs. 6.1 +/- 0.3% in rat, P < 0.05) and sarcomere length (3.3 +/- 0.3% in cat vs. 6.1 +/- 0.3% in rat, P < 0.05). To determine whether these species-dependent differences in length were related to diastolic interaction of the contractile elements or differences in relative passive stiffness, cardiocytes were subjected to the osmolarity gradient 1) during treatment with 7 mM 2,3-butanedione monoxime (BDM), which inhibits cross-bridge interaction, or 2) after pretreatment with 1 mM ethylene glycol-bis(beta-aminoethyl ether)-N, N,N',N'-tetraacetic acid (EGTA), a bivalent Ca2+ chelator. Treatment with EGTA or BDM abolished the differences between cat and rat cardiocytes. Species-dependent differences therefore appeared to be related to the degree of diastolic cross-bridge association and not differences in relative passive stiffness. In conclusion, the osmolarity vs. cell size relation is useful in assessing the cardiocyte response to anisosmotic stress and may in future studies be useful in assessing changes in relative passive cardiocyte stiffness produced by pathological processes.

Non-NASA Center↗

Meteoroid-bumper interactions program

An investigation has been made of the interaction of meteoroids with shielded structures. The interaction has been simulated by the impact of Lexan cylinders onto lead shields in order to provide the vaporous debris believed to be created by meteoroid impact on a space vehicle. Shock compression data for Lexan was determined. This, in combination with the known shock compression data for the lead shield, has permitted the definition of the initial high pressure states in the impacted projectile and shield. The debris from such impact events has been permitted to interact with aluminum main walls. The walls were chosen to be sufficiently large to be effectively infinite in diameter compared to the loaded area. The thickness of the wall and the spacing from the shield were varied to determine the effect of these parameters. In addition, the effect of having a body of water behind the wall has been assessed. Measurements of the stagnation pressure in the debris cloud have been made and correlated with the response of the main wall.

Gough, P. S.↗

Cold-air performance of a 12.766-centimeter-tip-diameter axial-flow cooled turbine. 3: Effect of rotor tip clearance on overall performance of a solid blade configuration

Two tip clearance configurations, one with a recess in the casing and the other with a reduced rotor blade height, were investigated at design equivalent speed over a range of tip clearance from about 2.0 to 5.0 percent of the stator blade height. The optimum configuration with a recess in the casing was the one where the rotor tip diameter was equal to the stator tip diameter (zero blade extension). For this configuration there was an approximate 1.5 percent decrease in total efficiency for an increase in tip clearance of 1 percent of stator blade height. For the reduced blade height configurations there was an approximate 2.0 percent decrease in total efficiency for an increase in tip clearance of 1 percent of stator blade height.

Haas, J. E.↗

Conceptual Design of a Gulled-Wing Commercial Transport

Open rotor powerplants have long been discussed as a potential solution to reduce aircraft fuel burn by increasing effective bypass ratio. However, this promising technology presents unique integration challenges. A gulled-wing approach for commercial transports is proposed to accommodate large-diameter powerplants. Integration effects of open rotor powerplants are modeled, analyzed, and discussed. Aerodynamic analysis and refined structural weight estimates are used to inform a preliminary conceptual design. Mission analysis of this model is performed, and the results are compared against NASA’s 154-passenger N+3 Conventional Configuration advanced technology baseline. Results indicate that gulled wings prove a viable solution for integrating large powerplants. Application of an open rotor engine model resulted in a fuel burn benefit on the order of 15% compared to the conventional turbofan configuration.

Conceptual Design↗

Association of particulate air pollution and acute mortality: involvement of ultrafine particles?

Recent epidemiological studies show an association between particulate air pollution and acute mortality and morbidity down to ambient particle concentrations below 100 micrograms/m3. Whether this association also implies a causality between acute health effects and particle exposure at these low levels is unclear at this time; no mechanism is known that would explain such dramatic effects of low ambient particle concentrations. Based on results of our past and most recent inhalation studies with ultrafine particles in rats, we propose that such particles, that is, particles below approximately 50 nm in diameter, may contribute to the observed increased mortality and morbidity In the past we demonstrated that inhalation of highly insoluble particles of low intrinsic toxicity, such as TiO2, results in significantly increased pulmonary inflammatory responses when their size is in the ultrafine particle range, approximately 20 nm in diameter. However, these effects were not of an acute nature and occurred only after prolonged inhalation exposure of the aggregated ultrafine particles at concentrations in the milligrams per cubic meter range. In contrast, in the course of our most recent studies with thermodegradation products of polytetrafluoroethylene (PTFE) we found that freshly generated PTFE fumes containing singlet ultrafine particles (median diameter 26 nm) were highly toxic to rats at inhaled concentrations of 0.7-1.0 x 10(6) particles/cm3, resulting in acute hemorrhagic pulmonary inflammation and death after 10-30 min of exposure. We also found that work performance of the rats in a running wheel was severely affected by PTFE fume exposure. These results confirm reports from other laboratories of the highly toxic nature of PTFE fumes, which cannot be attributed to gas-phase components of these fumes such as HF, carbonylfluoride, or perfluoroisobutylene, or to reactive radicals. The calculated mass concentration of the inhaled ultrafine PTFE particles in our studies was less than 60 micrograms/m3, a very low value to cause mortality in healthy rats. Aging of the fumes with concomitant aggregation of the ultrafine particles significantly decreases their toxicity. Since ultrafine particles are always present in the urban atmosphere, we suggest that they play a role in causing acute lung injury in sensitive parts of the population.

NASA Discipline Environmental Health↗

Hypervelocity Dust Impact in Olivine: Fib/Tem Characterization and Comparison of Experimental and Natural Microcraters

The flux of objects impacting the surfaces of solar system airless bodies is dominated by micrometeoroids less than 1 mm diameter whose impact effects play a major role in the space weathering of airless body surfaces. To obtain better understanding of how small scale impact effects vary as a function of impact speed in an important lunar and asteroidal mineral, we produced artificial microcraters in San Carlos olivine using Fe metal dust particles 0.10 to 5 µm in diameter electrostatically accelerated to speeds between 0.35 to 25 km s-1. The crater morphologies, size distrrubiton and microstruc-tures were characterized by field-emission SEM (FE-SEM) and also by FIB cross sectioning of selected craters for field-emission scanning transmission electron microscopy (FE-STEM). These same techniques were also applied to study a natural 20 µm-diameter microcrater in a olivine grain on the surface of lunar rock 12075. Measured microcrater diameters in the experimental sample range between 0.20 to 5 µm with larger craters having more irregular outlines dominated by spallation fractures. FE-SEM and FE-STEM imaging docu-ment the formation of shock melt in the size population of experimental craters below approximately 1 µm in diameter, corresponding to particle impact speeds in the 10-25 km s-1 range. The natural olivine crater exhibits similar shock melt features along the perimeter of its cavity, but the shock melt also contains nanophase Fe metal particles, something not observed in the experimental samples. FE-STEM imaging of the experimental craters reveals complex shock-generated dislocation and nanofracture microstructures in zones extend-ing 1-2 µm into the olivine from the crater cavity. The natural microcrater shows a lower density of shock-generated disloca-tions that extends a factor of 2 deeper into the the olivine than in the experimental samples.

Roy Gray Christoffersen↗