Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Mechanical and microstructural characterization of 6061 aluminum alloy strips severely deformed by Dissimilar Channel Angular Pressing

Dissimilar Channel Angular Pressing (DCAP) is a severe plastic deformation technique to improve the mechanical properties of flat products by producing ultrafine grains. In this study, the changes in the microstructure and mechanical properties of 6061 Al-alloy strips deformed by various numbers of DCAP passes were investigated. Some DCAPed samples were also held at 200 deg. C and 350 deg. C to investigate the effect of post-annealing. Mechanical properties were determined by hardness and tension tests; and microstructural changes were investigated by TEM analysis. Up to a critical level of plastic strain, remarkable improvements have been observed in the strength and hardness of the severely deformed strips; and the improvements have been explained by variations in grain size, dislocation structure, and formation of subgrains. - Research Highlights: {yields}Dissimilar Channel Angular Pressing (DCAP). {yields}Severe plastic deformation (SPD). {yields}Transmission Electron Microscopy of the 6061 Al alloy. {yields}Mechanical Properties of 6061 Al alloy.

36 MATERIALS SCIENCE↗

Deformation Behavior and Structure of i-Al-Cu-Fe Quasicrystalline Alloy in Vicinity of Nanoindenter Indentation

The nanoindentation tests have been carried out for the quasicrystalline polygrain Al{sub 62.4}Cu{sub 25.3}Fe{sub 12.3} alloy with the icosahedral structure i; the load P-displacement h diagrams have been used to estimate the contributions of plastic deformation (monotonic and intermittent), and the structures of the transverse microscopic sections have been studied in the vicinity of indentations by electron microscopy. It is shown that several systems of deformation bands are formed in the elasto-plastic zone in the vicinity of the indentations along the close-packed planes of the i lattice with the five-fold and two-fold symmetry axes; the bands often begin from cracks and manifest the signs of the dislocation structure. The traces of the phase transformation with the formation of the β-phase areas are observed only in a thin layer under an indenter. The effects of intermittent deformation are up to 50% of the total inelastic deformation and are related to the plastic behavior of the quasicrystal-activation and passage of deformation bands and also the formation of undersurface micro- and nanosized cracks.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Theoretical Investigation of Microstructure Evolution and Deformation of Zirconium Under Cascade Damage Conditions

This work is based on our reaction-diffusion model of radiation growth of Zr-based materials proposed recently in "On the Origin of Radiation Growth of HCP Crystals". In "On the Origin of Radiation Growth of HCP Crystals", the equations for the strain rates in unloaded pure crystal under cascade damage conditions of, e.g., neutron or heavy-ion irradiation were derived as functions of dislocation densities, which include contributions from dislocation loops, and spatial distribution of their Burgers vectors. The model takes into account the intra-cascade clustering of self-interstitial atoms and their one-dimensional diffusion; explains the growth stages, including the break-away growth of pre-annealed samples; and accounts for some striking observations, such as of negative strain in prismatic direction, and co-existence of vacancy- and interstitial-type prismatic loops. In this report, the change of dislocation densities due to accumulation of sessile dislocation loops is taken into account explicitly to investigate the dose dependence of radiation growth. The dose dependence of climb rates of dislocations is calculated, which is important for the climb-induced glide model of radiation creep. The results of fitting the model to available experimental data and some numerical calculations of the strain behavior of Zr for different initial dislocation structures are presented and discussed. The computer code RIMD-ZR.V1 (Radiation Induced Microstructure and Deformation of Zr) developed is described and attached to this report.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Single versus successive pop-in modes in nanoindentation tests of single crystals

From recent nanoindentation experiments, two types of pop-in modes have been identified: a single pop-in with a large displacement excursion, or a number of pop-ins with comparable and small displacement excursions. Theoretical analyses are developed here to study the roles played by indenter tip radius, pre-existing defect density, heterogeneous nucleation source type, and lattice resistance on the pop-in modes. The evolution of dislocation structures in earlier pop-ins provides input to modeling a stochastic, heterogeneous mechanism that may be responsible for the subsequent pop-ins. It is found that when the first pop-in occurs near theoretical shear stress, the pop-in mode is determined by the lattice resistance and tip radius. When the first pop-in occurs at low shear stress, whether the successive pop-in mode occurs depends on how the heterogeneous dislocation nucleation source density increases as compared to the increase of the total dislocation density. Lastly, the above transitions are found to correlate well with the ratio of indenter tip radius to the mean spacing of dislocation nucleation sources.

36 MATERIALS SCIENCE↗

Indentation size effect in tungsten: Quantification of geometrically necessary dislocations underneath the indentations using HR-EBSD

Highlights: • Revealed the dislocation structure below nanoindentations via ECCI and HR-EBSD. • Experimentally quantification of GND densities, with higher GND densities at lower depths. • Qualitative validation of the Nix-Gao model on the indentation size effect. - Abstract: During indentation testing of the low defect density crystalline materials, higher hardness values are found at lower indentation depths, which is referred to as an indentation size effect. The depth-dependence of hardness can be described by the Nix-Gao model, which is based on the concept of Geometrically Necessary Dislocations (GNDs). The underlying dislocation mechanism remains, however, unclear and requires independent measurement of GND density below the indentation. In the present work, the depth-dependency of the GND density is quantified underneath the Berkovich indentations in tungsten via high-resolution electron backscatter diffraction. There a higher GND density is found for lower indentation depths, resulting in a higher Taylor hardness for measured GND density.

36 MATERIALS SCIENCE↗

Unlimited damage accumulation in metallic materials under cascade-damage conditions

Most experiments on neutron or heavy-ion cascade-produced irradiation of pure metals and metallic alloys demonstrate continuous unlimited void growth as well as development of the dislocation structure. In contrast, the theory of radiation damage predicts saturation of void swelling at sufficiently high irradiation doses and according termination of accumulation of interstitial-type defects. It is shown in the present paper that, in the conditions of steady production of one-dimensionally (1-D) mobile clusters of self-interstitial atoms (SIAs) in displacement cascades, three reasons can be behind these observations. First, if the fraction of SIAs generated in the clustered form is smaller than some finite value of the order of the dislocation bias factor. Second, if solute, impurity or transmuted atoms segregate to voids and repel the SIA clusters. Third, if spatial correlations between voids and other defects, such as second-phase precipitates and dislocations, establish that provide shadowing of voids from the SIA clusters. The driving force for the development of such correlations is the same as for the void lattice formation and is argued to be always present under cascade-damage conditions. It is emphasized that the mean-free path of 1-D migrating SIA clusters is typically at least an order of magnitude longer than the average distance between microstructural defects; hence spatial correlations on the same scale should be taken into consideration. A way of developing a predictive theory is discussed. An interpretation of the universal steady-state swelling rate of ~1%/dpa observed in austenitic steels is proposed for the first time.

36 MATERIALS SCIENCE↗

High temperature (900-1300 C) mechanical behaviour of dendritic web grown silicon ribbons - Strain rate and temperature dependence of the yield stress

The mechanical behavior of dendritic web Si ribbons close the melting point was studied experimentally. The goal of the study was to generate data for modeling the generation of stresses and dislocation structures during growth of dendritic web Si ribbons, thereby permitting modifications to the production process, i.e., the temperature profile, to lower production costs for the photovoltaic ribbons. A laser was used to cut specimens in the direction of growth of sample ribbons, which were then subjected to tensile tests at temperatures up to 1300 C in an Ar atmosphere. The tensile strengths of the samples increased when the temperature rose above 1200 C, a phenomena which was attributed to the diffusion of oxygen atoms to the quasi-dislocation sites. The migration to the potential dislocations sites effectively locked the dislocations.

Mathews, V. K.↗

Response of 9Cr-ODS Steel to Proton Irradiation at 400 °C

The stability of Y–Ti–O nanoclusters, dislocation structure, and grain boundary segregation in 9Cr-ODS steels has been investigated following proton irradiation at 400 °C with damage levels up to 3.7 dpa. A slight coarsening and a decrease in number density of nanoclusters were observed as a result of irradiation. The composition of nanoclusters was also observed to change with a slight increase of Y and Cr concentration in the nanoclusters following irradiation. Size, density, and composition of the nanoclusters were investigated as a function of nanocluster size, specifically classified to three groups. In addition to the changes in nanoclusters, dislocation loops were observed after irradiation. Finally, radiation-induced enrichment of Cr and depletion of W were observed at grain boundaries after irradiation.

99 GENERAL AND MISCELLANEOUS↗

Characterization of twin boundaries in an Fe–17.5Mn–0.56C twinning induced plasticity steel

A twinning-induced plasticity steel of composition Fe–17.5 wt.% Mn–0.56 wt.% C–1.39 wt.% Al–0.24 wt.% Si was analyzed for the purpose of characterizing the relationship between tensile strain and deformation twinning. Tensile samples achieved a maximum of 0.46 true strain at failure, and a maximum ultimate tensile strength of 1599 MPa. Electron backscatter diffraction (EBSD) analysis showed that the grain orientation rotated heavily to < 111 > parallel to the tensile axis above 0.3 true strain. Sigma 3 misorientations, as identified by EBSD orientation measurements, and using the image quality maps were used to quantify the number of twins present in the scanned areas of the samples. The image quality method yielded a distinct positive correlation between the twin area density and deformation, but the orientation measurements were unreliable in quantifying twin density in these structures. Quantitative analysis of the twin fraction is limited from orientation information because of the poor spatial resolution of EBSD in relation to the twin thickness. The EBSD orientation maps created for a thin foil sample showed some improvement in the resolution of the twins, but not enough to be significant. Measurements of the twins in the transmission electron microscopy micrographs yielded an average thickness of 23 nm, which is near the resolution capabilities of EBSD on this material for the instrumentation used. Electron channeling contrast imaging performed on one bulk tensile specimen of 0.34 true strain, using a method of controlled diffraction, yielded several images of twinning, dislocation structures and strain fields. A twin thickness of 66 nm was measured by the same method used for the transmission electron microscopy measurement. It is apparent that the results obtain by electron channeling contrast imaging were better than those by EBSD but did not capture all information on the twin boundaries such as was observed by transmission electron microscopy. - Highlights: • Performed tensile tests to assess mechanical performance of TWIP alloy • Analyzed tensile specimens using EBSD, TEM, and ECCI • EBSD showed that most twinning occurred at or near the < 111 >//TA orientation. • EBSD, TEM and ECCI were used to measure average twin density. • Compared spatial resolution of EBSD, ECCI and TEM for the instrumentation used.

36 MATERIALS SCIENCE↗

The microstructure and formation mechanism of face-centered cubic Ti in commercial pure Ti foils during tensile deformation at room temperature

Highlights: • Two variants of fcc-Ti appear in ultra-thin commercial pure Ti foils during tension. • The appearance of obvious yield point may be attributed to the formation of fcc-Ti. • The orientation relationship between fcc-Ti phase and hcp-Ti matrix is determined. • The characteristics of dislocation structure in fcc-Ti are identified. • A model for the formation of fcc-Ti is proposed. - Abstract: Two variants of face-centered cubic (fcc) Ti phase appear in ultra-thin commercial pure Ti foils with hexagonal closed packed (hcp) structure during tensile deformation at room temperature. The orientation relationship between fcc-Ti phase and hcp-Ti matrix is determined as <0001>{sub HCP} // <001>{sub FCC}, <11 2-bar 0>{sub HCP} // <1 1-bar 0>{sub FCC} and <01 1-bar 0>{sub HCP} // <110> {sub FCC}. The fcc-Ti phase with a habit plane of {01 1-bar 0}{sub HCP} usually nucleates at grain boundary and grows along the direction of <11> } } }2 }&<; }0 2-bar 0 </>{sub HCP}. The thickness of fcc-Ti phase with a shape of thin plate ranges from 10 nm to 200 nm. Dislocations, steps and stacking faults with a space of 0.58 nm can be seen in fcc-Ti. The formation of a five-layer fcc-Ti can be accomplished by the formation of stacking faults and gliding of 1/6[11 2-bar 0] Shockley partial dislocations on the prismatic plane of hcp-Ti. The 1/3[11 2-bar 0] dislocations in hcp-matrix can cross the fcc-Ti phase because the Burgers vector of these dislocations is coincidence with 1/2[110] dislocations in the fcc-Ti.

36 MATERIALS SCIENCE↗

Defects and stresses in MBE-grown GaN and Al{sub 0.3}Ga{sub 0.7}N layers doped by silicon using silane

The electric and structural characteristics of silicon-doped GaN and Al{sub 0.3}Ga{sub 0.7}N layers grown by molecular beam epitaxy (MBE) using silane have been analyzed by the Hall effect, Raman spectroscopy, and high-resolution X-ray diffractometry. It is established that the electron concentration linearly increases up to n = 4 × 10{sup 20} cm{sup −3} with an increase in the silane flow rate for GaN:Si, whereas the corresponding dependence for Al{sub 0.3}Ga{sub 0.7}N:Si is sublinear and the maximum electron concentration is found to be n = 4 × 10{sup 19} cm{sup −3}. X-ray measurements of sample macrobending indicate a decrease in biaxial compressive stress with an increase in the electron concentration in both GaN:Si and Al{sub 0.3}Ga{sub 0.7}N:Si layers. The parameters of the dislocation structure, estimated from the measured broadenings of X-ray reflections, are analyzed.

36 MATERIALS SCIENCE↗

On the distribution of stacking faults at dissociated medium-angle grain boundaries: Crystallographic geometry and metastability

Grain boundaries in FCC metals with low stacking-fault energy can form in dissociated configurations of stacking faults. Perhaps the most studied example is 9R stacking at boundaries near Σ3{112}, where the distribution of stacking faults is related to the emission of Shockley partial dislocations. Here, we combine atomic-resolution electron microscopy, atomistic simulations, and dislocation theory to demonstrate that boundaries vicinal to Σ33a support the stabilization of dissociated 9R stacking within a narrow range of inclinations. This boundary is interesting since its misorientation (20.05°) lies in the medium-angle regime, just past the upper misorientation limit for low-angle boundaries, motivating questions for how best to describe it in terms of dislocations. Our HAADF-STEM observations of thin film bicrystals, supported by atomistic modeling, reveal that this inclination dependence arises from specific geometric constraints on the arrangement of Shockley partial dislocations at the interface. Quantification of stacking-fault distributions across multiple boundaries indicates that the density and spacing of faults closely follow the ideal 9R motif, with subtle variations reflecting the complex energy landscape of these boundaries. Through energetic analysis, we establish the presence of competing metastable states enabled by variations in stacking sequences, emphasizing the significant role of crystallographic geometry. We generalize our analysis as a function of misorientation, showing how 9R at the Σ33a boundary is related to previous observations and calculations of HCP at a 29.7° boundary. This study provides a crystallographically grounded framework connecting dislocation structures, stacking-fault distributions, and metastability at grain boundaries in FCC metals.

Atomistic modeling↗

Effect of heavy ion irradiation on microstructural evolution in CF8 cast austenitic stainless steel

The microstructural evolution in ferrite and austenitic in cast austenitic stainless steel (CASS) CF8, as received or thermally aged at 400 °C for 10,000 h, was followed under TEM with in situ irradiation of 1 MeV Kr ions at 300 and 350 °C to a fluence of 1.9 × 10 15 ions/cm 2 (~3 dpa) at the IVEM-Tandem Facility. For the unaged CF8, the irradiation-induced dislocation loops appeared at a much lower dose in the austenite than in the ferrite. At the end dose, the austenite formed a well-developed dislocation network microstructure, while the ferrite exhibited an extended dislocation structure as line segments. Compared to the unaged CF8, the aged specimen appeared to have lower rate of damage accumulation. The rate of microstructural evolution under irradiation in the ferrite was significantly lower in the aged specimen than in the unaged. Finally, we attributed this difference to the different initial microstructures in the unaged and aged specimens, which implies that thermal aging and irradiation are not independent but interconnected damage processes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantifying irradiation defects in zirconium alloys: a comparison between transmission electron microscopy and whole-pattern diffraction line-profile analysis - 2016-0089

Irradiation-induced dislocations significantly affect the mechanical properties of zirconium alloys, altering slip and influencing creep and growth. Thus, the quantitative characterization of irradiation defects as a function of fluence, cold work, and/or thermal treatments is important for models that attempt to predict their impact on properties. Whole-pattern diffraction line-profile analysis (DLPA) is a well-established modern tool for microstructure characterization based on first-principle physical models for dislocation density measurements in plastically deformed materials. However, applying these DLPA methods directly to irradiated materials yields higher than expected dislocation density values compared with historical transmission electron microscopy (TEM) measurements and past line-broadening analysis studies calibrated to TEM observations. In an effort to understand these differences, a new microstructural model was developed for DLPA to specifically address dislocation structures consisting of elliptical - and -component loops. To compare the refined DLPA method with TEM measurements, high-resolution neutron diffraction patterns on nonirradiated and irradiated Zr-2.5Nb samples were collected with the Neutron Powder Diffractometer instrument at the Los Alamos Neutron Science Center and were evaluated. High-resolution TEM measurements were performed at the Reactor Materials Testing Laboratory, Queen's University, for comparison with the DLPA results. The capabilities and inherent uncertainties of both the refined DLPA and TEM methods are compared and discussed in detail. We show that the differences between the density values provided by DLPA and TEM are inherent to the methods and can be reconciled with the interpretation of the data. (authors)

36 MATERIALS SCIENCE↗

Analysis of Localized Deformation Processes in Highly Irradiated Austenitic Stainless Steel through In Situ Techniques

This report describes new experimental results obtained during in situ mechanical tests with neutron-irradiated (10.7 dpa) austenitic 304L steel specimens. The in situ tensile tests inside a scanning electron microscope (SEM) were accompanied by modern high-resolution electron backscatter diffraction (HR-EBSD) analysis. The HR-EBSD approach allowed for investigating and quantifying internal stresses and dislocation structures in nondeformed and deformed steels, materials used in light water reactor internal components. The literature regarding the HR-EBSD analysis of metals and alloys is very limited, and practically no publications on the HR-EBSD analysis coupled with in situ tests are available. Experimental work, performed at Oak Ridge National Laboratory’s Low Activation Materials Development and Analysis facility, is detailed in this report. Section 1 briefly describes strain and stress localization processes and underlines their importance and role in irradiated materials, materials used in nuclear power plants. The section demonstrates that very limited quantitative data exist regarding localized stresses and strains in the irradiated materials at the meso-level (i.e., inside the grain, for a group of interacting grains, or for channel–grain boundary [GB] interaction) whereas local stresses at GBs are key contributors to the stress corrosion crack initiation.Section 2 documents the key methods used to conduct the experimental work: the SEM/EBSD system, miniature tensile frame, and irradiated material. Irradiated specimen manufacturing is described, as this option may be of special interest for other projects. Section 3 provides details of the HR-EBSD in situ tests (e.g., tensile curves, geometry, dimensions of regions of interest, load, and deformation steps). Section 4 discusses the results related to the evolution of geometrically necessary dislocations (GNDs) and their density, spatial, and statistical distributions.Section 5 focuses on the HR-EBSD analysis with respect to a channel–GB interaction. Two aspects are discussed in detail: mapping and analyzing the GND fields before and after loading, and the possibility of investigating local stresses and elastic strains at the channel–GB interaction. The present work results are beneficial for understanding strain and stress localization processes leading to crack initiation, for analyzing the material after long-term in-service life, and for developing predictive models. Section 6 summarizes the work performed and discusses future activities within this research direction.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Observation of thermally etched grain boundaries with the FIB/TEM technique

Thermal etching is a method which is able to reveal and characterize grain boundaries, twins or dislocation structures and determine parameters such as grain boundary energies, surface diffusivities or study phase transformations in steels, intermetallics or ceramic materials. This method relies on the preferential transfer of matter away from grain boundaries on a polished sample during heating at high temperatures in an inert/vacuum atmosphere. The evaporation/diffusion of atoms at high temperatures results in the formation of grooves at the intersections of the planes of grain/twin boundaries with the polished surface. This work describes how the combined use of Focussed Ion Beam and Transmission Electron Microscopy can be used to characterize not only the grooves and their profile with the surface, but also the grain boundary line below the groove, this method being complementary to the commonly used scanning probe techniques. - Highlights: • Thermally etched low-carbon steel samples have been characterized by FIB/TEM • Grain boundary (GB) lines below the groove have been characterized in this way • Absence of ghost traces and large θ angle suggests that GB are not stationary but mobile • Observations correlate well with previous works and Mullins' investigations [22].

36 MATERIALS SCIENCE↗

Low cycle fatigue performance of Ni-based superalloy coated with complex thermal barrier coating

Highlights: • Novel thermal barrier coating (TBC) with YSZ and ZrO{sub 2} + SiO{sub 2} + Al{sub 2}O{sub 3} eutectic ceramic top coat • TBC deposited via atmospheric plasma spraying and a hybrid water stabilized plasma torch spraying • Effect of eutectic ceramic TBC on LCF behaviour at 900 °C • Damage mechanisms in cyclic loading of cast nickel-based superalloy coated with TBC • The dislocation structures of a Ni-base superalloy were observed. - Abstract: Thermal barrier coatings (TBCs) are widely applied to protect high-temperature components against high temperatures in harsh environments. Nineteen cylindrical specimens of Inconel 713LC were manufactured using the investment castings technique, and 10 specimens were subsequently coated with a novel complex thermal barrier coating (TBC) system. The TBC system comprises a metallic CoNiCrAlY bond coat (BC) and a complex ceramic top coat (TC). The TC is a mixture of a near eutectic nanocrystalline ceramic made of zirconia (ZrO{sub 2}), alumina (Al{sub 2}O{sub 3}), silica (SiO{sub 2}) and conventional yttria stabilized zirconia (YSZ) ceramic in the ratio of 50/50 in wt%. Low cycle fatigue (LCF) tests were carried out in a symmetrical push-pull cycle under strain control at 900 °C. Cyclic hardening/softening curves, cyclic stress-strain curves and fatigue life curves of the TBC-coated and uncoated material were assessed. Fatigue life curves in total strain representation showed transient behaviour. Fracture surfaces and polished sections parallel to the loading axis of the TBC-coated and uncoated specimens prior and after cyclic loading were observed by means of scanning electron microscopy (SEM) to study the degradation mechanisms during high-temperature LCF. TBC delamination was observed at the TC/BC interface, and rafting of precipitates occurred after high-temperature exposure. The microstructural investigations further the discussion of the differences in the stress-strain response and the fatigue life of the TBC-coated and uncoated superalloy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A duality-based coupling of Cosserat crystal plasticity and phase field theories for modeling grain refinement

High-rate deformation processes of metals entail intense grain refinement and special attention needs to be paid to capture the evolution of microstructure. In this article, a new formulation for coupling Cosserat crystal plasticity and phase field is developed. A common approach is to penalize kinematic incompatibility between lattice orientation and displacement-based elastic rotation. However, this can lead to significant solution sensitivity to the penalty parameter, resulting in low accuracy and convergence rates. To address these issues, a duality-based formulation is developed which directly imposes the rotational kinematic compatibility. A weak inf-sup-based skew-symmetric stress projection is introduced to suppress instabilities present in the dual formulation. An additional least squares stabilization is introduced to suppress the spurious lattice rotation with a suitable parameter range derived analytically and validated numerically. The required high-order continuity is attained by the reproducing kernel approximation. It is observed that equal order displacement-rotation-phase field approximations are stable, which allows efficient employment of the same set of shape functions for all independent variables. The proposed formulation is shown to yield superior accuracy and convergence with marginal parameter sensitivity compared to the penalty-based approach and successfully captures the dominant rotational recrystallization mechanism including block dislocation structures and grain boundary migration.

42 ENGINEERING↗