Search NASA⌕ Search

SEARCH · Search NASA

Results for “Drag models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Models of Lift and Drag Coefficients of Stalled and Unstalled Airfoils in Wind Turbines and Wind Tunnels

Equations are developed with which to calculate lift and drag coefficients along the spans of torsionally-stiff rotating airfoils of the type used in wind turbine rotors and wind tunnel fans, at angles of attack in both the unstalled and stalled aerodynamic regimes. Explicit adjustments are made for the effects of aspect ratio (length to chord width) and airfoil thickness ratio. Calculated lift and drag parameters are compared to measured parameters for 55 airfoil data sets including 585 test points. Mean deviation was found to be -0.4 percent and standard deviation was 4.8 percent. When the proposed equations were applied to the calculation of power from a stall-controlled wind turbine tested in a NASA wind tunnel, mean deviation from 54 data points was -1.3 percent and standard deviation was 4.0 percent. Pressure-rise calculations for a large wind tunnel fan deviated by 2.7 percent (mean) and 4.4 percent (standard). The assumption that a single set of lift and drag coefficient equations can represent the stalled aerodynamic behavior of a wide variety of airfoils was found to be satisfactory.

Spera, David A.↗
NASA NTRS1954

Free-Flight Zero-Lift Drag Results from a 1/5-Scale Model and Several Small-Scale Equivalent Bodies of Revolution of the Convair F-102 Configuration at Mach Numbers up to 1.34

A 1/5-scale, rocket-propelled model of the Convair F-102 configuration was tested in free flight to determine zero-lift drag at Mach numbers up to 1.34 and at Reynolds numbers comparable to those of the full-scale airplane. This large-scale model corresponded to the prototype airplane and had air flow through the duct. Additional zero-lift drag tests involved a series of small equivalent bodies of revolution which were launched by means of a helium gun. The several small-scale models tested corresponded to: the basic configuration, the 1/5-scale rocket-propelled model configuration, a 2-foot (full-scale) fuselage-extension configuration, and a 7-foot (full-scale) fuselage-extension configuration. Models designed to correspond to the area distribution at a Mach number of 1.0 were flown for each of these 'shapes and, in addition, models designed to correspond to the area distribution at a Mach number of 1.2 were flown for the 1/5-scale rocket-propelled model and the 7-foot-fuselage-extension configuration. The value of external pressure drag coefficient (including base drag) obtained from the large-scale rocket model was 0.0190 at a Mach number of 1..05 and the corresponding values from the equivalent-body tests varied from 0.0183 for the rocket-propelled model shape to 0.0137 for the 7-foot-fuselage-extension configuration. From the results of tests of equivalent bodies designed to correspond to the area distribution at a Mach number of 1.0, it is evident that the small changes in shape incorporated in the basic and 2-foot-fuselage-extension configurations from that of the rocket-propelled model configuration will provide no significant change in pressure drag. On the other hand, the data from the 7-foot-fuselage-extension model indicate a substantial reduction in pressure drag at transonic speeds.

Wallskog, Harvey A.↗
DOE OSTI2025

Gas and dust dynamics in γ Cephei-type disks

Context. Giant planets are observed orbiting the primary stars of close binary systems. Such planets may have formed in compact circumprimary disks, which once surrounded these stars, under conditions much different than those encountered around single stars. Aims. In order to quantify the effects of the strong gravitational perturbations exerted on circumprimary disk material, the three-dimensional (3D) dynamics of gas and dust in orbit around the primary star of a compact and eccentric binary system was modeled by applying the stellar and orbital parameters of γ Cephei, a well-known system that can be representative of a class of close binaries. Methods. Circumprimary gas was approximated as an Eulerian viscous and compressible fluid and modeled by means of 3D hydrodynamical simulations, assuming locally isothermal conditions in the medium around the primary star. Dust grains were modeled as Lagrangean particles, subjected to gravity and aerodynamic drag forces. Models that include a giant planet were also considered. Results. Models indicate that spiral density waves excited around pericenter passage propagate toward the inner boundary of the disk, through at least a few pressure scale-heights from the mid-plane, inducing radial and vertical mixing in the gas. However, perturbations imparted to gas, both in terms of eccentricity and precession, are far weaker than previously estimated by two-dimensional (2D) simulations. Models predict small eccentricities, ≲0.03, and slow retrograde precession. The addition of a giant planet does not change the low eccentricity state of the disk. The parameters applied to the disk would lead to the formation of a massive planet, many times the mass of Jupiter, in agreement with some observations. Micron to mm-size dust grains are well coupled to the gas, resulting in similar dynamics and statistically similar distributions of orbital elements. The planet only affects the dust distributions locally. In agreement with outcomes of recent 2D models, the lifetime of an isolated circumprimary disk would be brief, ~10 5 years, because of its compact nature, requiring a long-term external supply of mass to allow for the in situ formation of a giant planet.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Uncertainty quantification of bank vegetation impacts on the flood flow field in the American River, California, using large‐eddy simulations

Bank vegetation plays a key role in both hydrodynamics and morphodynamics of natural rivers; however, these effects are often unaccounted for in the computational flow dynamics of natural waterways. Recent studies using the large‐eddy simulation (LES), however, have attempted to gain insights into the impacts of bank vegetation on the mean flow field of the natural rivers using a vegetation model, which applies a sink term to the momentum equations of motion. This approach accounts for the effects of the vegetation and provides a practical approach to account for the complex patches of bank vegetation in large‐scale rivers. To implement the vegetation model, a drag coefficient reflecting the overall resistance of vegetal structures to the flow is needed, but due to the lack of calibrated data and range of size, density and type of vegetation, this parameter can be a significant source of uncertainty in the model results. Here, in this study, we use uncertainty quantification (UQ) to investigate the hydrodynamics and bed shear results when a bank vegetation is incorporated in an LES model. To this end, we used the polynomial chaos expansion and Monte Carlo sampling techniques to determine the uncertainties associated with the drag coefficient in the vegetation model and from uncertainties in the bed roughness and inflow discharge. The UQ analysis provided spatially varying confidence levels for the spanwise and vertical distribution of velocity magnitude and for the bed shear stress distributions. In addition, Sobol indices were computed to indicate the relative influence that each parameter had on the overall uncertainty. In general, it was found that uncertainty in flow discharge was the dominant source of uncertainty; however, the drag coefficient in the vegetation model and the bed roughness parameter also made significant contribution to the uncertainty near the banks and bed, respectively.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2002

A Ground-Based Research Vehicle for Base Drag Studies at Subsonic Speeds

A ground research vehicle (GRV) has been developed to study the base drag on large-scale vehicles at subsonic speeds. Existing models suggest that base drag is dependent upon vehicle forebody drag, and for certain configurations, the total drag of a vehicle can be reduced by increasing its forebody drag. Although these models work well for small projectile shapes, studies have shown that they do not provide accurate predictions when applied to large-scale vehicles. Experiments are underway at the NASA Dryden Flight Research Center to collect data at Reynolds numbers to a maximum of 3 x 10(exp 7), and to formulate a new model for predicting the base drag of trucks, buses, motor homes, reentry vehicles, and other large-scale vehicles. Preliminary tests have shown errors as great as 70 percent compared to Hoerner's two-dimensional base drag prediction. This report describes the GRV and its capabilities, details the studies currently underway at NASA Dryden, and presents preliminary results of both the effort to formulate a new base drag model and the investigation into a method of reducing total drag by manipulating forebody drag.

Diebler, Corey↗
NASA NTRS1973

Horizontal variations in thermospheric composition.

Constant boundary conditions at 120 km have been so widely and successfully used in atmospheric modeling and in fitting atmospheric density data obtained from satellite drag to models that attention has been diverted from the variations that occur at 120 km, especially in composition. Atomic oxygen concentrations vary by factors as large as 4, with highest concentrations occurring in the winter hemisphere but at midlatitudes rather than over the polar region. A substantial additional degree of variability occurs that is especially associated with geomagnetic activity. The helium concentration varies by about an order of magnitude between poles, with the maximum concentration occurring at high winter latitudes and a secondary minimum occurring over the winter pole.

Johnson, F. S.↗
NASA NTRS1994

Evaluation of semiempirical atmospheric density models for orbit determination applications

This paper presents the results of an investigation of the orbit determination performance of the Jacchia-Roberts (JR), mass spectrometer incoherent scatter 1986 (MSIS-86), and drag temperature model (DTM) atmospheric density models. Evaluation of the models was performed to assess the modeling of the total atmospheric density. This study was made generic by using six spacecraft and selecting time periods of study representative of all portions of the 11-year cycle. Performance of the models was measured for multiple spacecraft, representing a selection of orbit geometries from near-equatorial to polar inclinations and altitudes from 400 kilometers to 900 kilometers. The orbit geometries represent typical low earth-orbiting spacecraft supported by the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD). The best available modeling and orbit determination techniques using the Goddard Trajectory Determination System (GTDS) were employed to minimize the effects of modeling errors. The latest geopotential model available during the analysis, the Goddard earth model-T3 (GEM-T3), was employed to minimize geopotential model error effects on the drag estimation. Improved-accuracy techniques identified for TOPEX/Poseidon orbit determination analysis were used to improve the Tracking and Data Relay Satellite System (TDRSS)-based orbit determination used for most of the spacecraft chosen for this analysis. This paper shows that during periods of relatively quiet solar flux and geomagnetic activity near the solar minimum, the choice of atmospheric density model used for orbit determination is relatively inconsequential. During typical solar flux conditions near the solar maximum, the differences between the JR, DTM, and MSIS-86 models begin to become apparent. Time periods of extreme solar activity, those in which the daily and 81-day mean solar flux are high and change rapidly, result in significant differences between the models. During periods of high geomagnetic activity, the standard JR model was outperformed by DTM. Modification of the JR model to use a geomagnetic heating delay of 3 hours, as used in DTM, instead of the 6.7-hour delay produced results comparable to or better than the DTM performance, reducing definitive orbit solution ephermeris overlap differences by 30 to 50 percent. The reduction in the overlap differences would be useful for mitigating the impact of geomagnetic storms on orbit prediction.

Cox, C. M.↗
NASA NTRSDate not supplied

X-57 Ground Dynamics Modeling and Analysis

This paper presents simulation work to assess the ground handling behavior of the X-57 airplane, prior to its first flight under electric propulsion. A tire deformation model was fit to manufacturer ground testing data to develop a detailed simulation model of previously unmodeled rolling drag forces on the tires. A special modeling effort corrected for a difference between the runway surface in the manufacturer data (grass) and in intended X-57 surface operations (asphalt/concrete). Analysis based on variation in the test conditions of the manufacturer test data showed that uncertainty in the new estimated rolling drag model should lead to no more than 1.5-percent uncertainty in the takeoff acceleration. Another batch simulation series swept across ground operating conditions and airplane configurations, characterizing turning radii and roll angles experienced for different open-loop steering commands in these various situations. This simulation allowed the identification of ground handling characteristics even beyond the regime of normal operations. As part of this task, a new, modified variant of the Fibonacci search algorithm identified the correct steering inputs for maintaining a straight path as a function of the operating condition. Finally, this paper describes a fixed-base piloted simulator assessment. This assessment supplements the previous simulated ground dynamics data with pilot-in-the-loop data and pilot feedback and confirms the overall acceptability of the ground handling qualities of the X-57 airplane prior to first flight.

Loren J. Newton↗
NASA NTRS1970

Drag Characteristics of Several Towed Decelerator Models at Mach 3

An investigation has been made to determine the possibility of using toroid-membrane and wide-angle conical shapes as towed decelerators. Parameter variations were investigated which might render toroid-membrane models and wide-angle- cone models stable without loss of the high drag coefficients obtainable with sting-mounted models. The parameters varied included location of center of gravity, location of the pivot between the towline and the model, and configuration modifications of the aft end as the addition of a corner radius and the addition of a skirt. The toroid membrane can be made into a stable towed decelerator with a suitable configuration modification of the aft end.

EXPERIMENTS↗
NASA NTRS1954

Effects of Fuselage Modifications on the Drag Characteristics of a 1/20-Scale Model of the Convair F-102 Airplane at Transonic Speeds

An investigation has been conducted in the Langley 8-foot transonic tunnel to determine the effects of several fuselage modifications on the transonic drag-rise characteristics of a 1/20-scale model of the Convair F-102 airplane. Tests covered an angle-of-attack range from 0deg to about 10deg and a Mach number range from 0.60 to 1.14. Results indicated that the transonic drag rise .for the basic F-102 airplane could be substantially reduced by extending the fuselage after-body approximately 8 percent of the fuselage length. Tests of other bodies indicated that a shorter (4-percent) afterbody extension may have a similar effect on the drag rise. Further improvement of the axial cross-sectional-area distribution of the 8-percent extended configuration through the addition of fuselage volume resulted in additional reductions in the drag rise at a Mach number of 1.0 and caused no or only slight drag penalties at the higher Mach numbers. The results of the present tests generally substantiate the area-rule concept with respect to the prediction of the transonic drag rise through the use of an equivalent-area body of revolution for a practical delta-wing airplane configuration.

Kelly, Thomas C.↗
NASA NTRS1955

Flight Investigation at Mach Numbers from 0.6 to 1.7 to Determine Drag and Base Pressures on a Blunt Trailing-edge Airfoil and Drag of Diamond and Circular-arc Airfoils at Zero Lift

Results of an exploratory free-flight investigation at zero lift of several rocket-powered drag-research models having rectangular 6-percent-thick wings are presented for a Mach number range of 0.6 to 1.7. Wings having diamond, circular-arc, and blunt-trailing-edge airfoil sections were tested. Pressures over the base of the blunt-trailing-edge airfoil were measured. The drags of all the models were measured and are compared with theory in this paper.

Morrow, John D↗
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗