Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - COOLING, INTERNAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of water droplet growth dynamics on electrode current in fuel-cell catalyst layers

Fuel cells are a promising next-generation energy-conversion technology designed to replace internal combustion engines in transportation applications. However, much work remains to optimize them. Operation at high humidities causes liquid water droplet formation on Pt catalyst particles during oxygen reduction, potentially impeding reactant arrival to the reactive electrode. In this work, four different cases of water droplet growth in fuel-cell catalyst layers are considered: pinned or advancing droplets on a bare Pt surface, advancing droplets on a Nafion film, and water-layer growth in carbon nanopores. Transient drop growth is captured with a combination of mass, species mass, and momentum balances, and the subsequent limiting current is determined via oxygen diffusion and Tafel kinetics. Further, water droplets are found not to be mass-transfer limiting due to the relatively large liquid-gas area compared to the Pt nanoparticle. Mass-transfer-limited behavior is calculated in carbon nanopores.

25 ENERGY STORAGE↗
DOE OSTI2021

Effect of nitric oxide and exhaust gases on gasoline surrogate autoignition: iso-octane experiments and modeling

Exhaust gas recirculation (EGR) is widely used in advanced internal combustion engines to reduce engine emissions as well as control combustion phasing. Among various species present in EGR gases, CO 2 and H 2 O are two major components that can thermally and chemically affect fuel autoignition. It is of fundamental interest to isolate the thermal and chemical effects of CO 2 and H 2 O on fuel autoignition, especially as such an effort has not been reported in the literature. Moreover, nitric oxide (NO) is known to exhibit strong chemical effects on fuel autoignition, which in turn affects engine combustion phasing. The effects of ultra-low NO addition (< 100 ppm) on fuel autoignition at low temperatures are also not well understood. Recognizing these problems, autoignition experiments of iso-octane (a major gasoline surrogate component) in air are performed in this study using a rapid compression machine at varying compressed pressures, equivalence ratios, dilution levels with an EGR gas analogue (consisting of CO 2 , H 2 O, O 2 , and N 2 ) and N 2 only, and varying amounts of NO addition. Furthermore, the thermal and chemical effects of the EGR gas analogue are isolated and evaluated by comparing the ignition delay time datasets of EGR and N2-only diluted cases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A wide range experimental and kinetic modeling study of the oxidation of 2,3-dimethyl-2-butene: Part 1

2,3-Dimethyl-2-butene (TME) is a potential fuel additive with high research octane number (RON) and octane sensitivity (S), which can improve internal combustion engine performance and efficiency. However, the combustion characteristics of TME have not been comprehensively investigated. Thus, it is essential to study the combustion characteristics of TME and construct a detailed chemical kinetic model to describe its combustion. In this paper, two high-pressure shock tubes and a constant-volume reactor are used to measure ignition delay times and laminar flame speeds of TME oxidation. Further, the ignition delay times were measured at equivalence ratios of 0.5, 1.0, and 2.0 in “air”, at pressures of 5 and 10 bar, in the temperature range of 950 – 1500 K. Flame speeds of the TME/ “air” mixtures were measured at atmospheric pressure, at a temperature of 325 K, for equivalence ratios ranging from 0.78 to 1.31. Two detailed kinetic mechanisms were constructed independently using different methodologies; the KAUST TME mechanism was constructed based on NUIGMech1.1, and the MIT TME mechanism was built using the Reaction Mechanism Generator (RMG). Both mechanisms were used to simulate the experimental results using Chemkin Pro. In the present work, reaction flux and sensitivity analyses were performed using the KAUST mechanism to determine the critical reactions controlling TME oxidation at the conditions studied.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Plasma assisted NH 3 /H 2 /air ignition in nanosecond discharges with non-equilibrium energy transfer

Ammonia (NH 3 ), with its high energy density and easiness to store and transport as a hydrogen carrier, has become a promising alternative green fuel. However, its adoption in power generation is hindered by challenges such as low burning velocity, slow low-temperature oxidation, high NO x emissions, and ignition difficulty. Here, this work computationally investigates the effects of non-equilibrium energy transfer by nanosecond discharges on NH 3 ignition and flame propagation in an NH 3 /H 2 /air flow at 700 K and 1 atm. The simulation results demonstrate that NH 3 /air mixtures require a large ignition energy due to their large critical ignition radius. It is shown that adding 30 % hydrogen significantly reduces the critical ignition radius and minimum ignition energy. Two-dimensional modeling further shows a non-monotonic dependence of ignition kernel volume on the applied voltage and reduced electric field. The optimum ignition enhancement occurs at 200 Td where the generation of electronically excited species and radicals including N 2 (B), O( 1 D) and OH becomes most efficient. Higher voltages divert electron energy toward ionization, which makes it less effective for NH 3 ignition. The study also identifies an optimal electrode gap size for a given pulse energy. Smaller gap sizes increase deposited energy density, raising temperature and radical concentrations. However, excessive reduction of the gap distance reduces flame propagation speed due to the flame stretch effect in rich mixtures with the effective Lewis number greater than unity. A nonlinear relationship between pulse repetition frequency and ignition kernel volume is observed in a nanosecond pulsed high frequency discharge (NPHFD). An optimal frequency range of 200 kHz to 2 MHz is found when two pulses are used. In addition, an optimal number of pulses exists for each pulse repetition frequency, with higher frequencies requiring more pulses to maximize the overlap region. These findings provide critical insights on developing controlled plasma discharge techniques for efficient NH 3 ignition in reactive flows within internal combustion engines and gas turbines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Study on ammonia and dimethyl ether oxidation and kinetic interaction up to 100 atm

NH 3 and DME dual fuel oxidation and kinetic coupling are experimentally studied by using a supercritical pressure jet-stirred reactor (SP-JSR) at 20 and 100 atm, over a temperature range of 500–900 K, and at fuel-lean and stoichiometric conditions with NH 3 to DME molar ratios of 4 and 0.62, respectively. An HP-Mech model for high-pressure NH3/DME oxidation is developed based on our previous studies and it shows generally better performance than other models in the literature on high-pressure oxidation experiments. Due to DME’s strong low-temperature reactivity, it dramatically enhances the oxidation of NH3 at low temperature. However, the effect of NH 3 on DME oxidation varies with temperature. At low temperatures, NH 3 inhibits low-temperature reactivity by consuming OH radicals. In addition, the NH 2 and NO x formation from NH 3 further suppresses the low-temperature DME reactivity by reducing alkylperoxyl and O 2 QOOH radicals via RO 2 + NH 2 = RO + H 2 NO, RO 2 + NO = RO + NO 2 and O 2 QOOH + NO = 2CH 2 O + HO 2 + NO 2 . At intermediate temperatures, due to enhanced kinetic coupling of NH 2 /NO x /HO 2 chemistry, DME oxidation is significantly promoted. It is found that there are two major NH 2 /NO x /HO 2 coupling pathways for OH radical production brought by NH 3 : (1) NH 2 + HO 2 = H 2 NO + OH and (2) NH 2 + NO 2 = H 2 NO + NO with NO + HO 2 = OH + NO 2 . Moreover, the resulting H 2 NO will further contribute to OH production via the H 2 NO/NO x /HONO coupling pathways: H 2 NO + NO 2 = HNO + HONO, HNO + NO 2 = HONO + NO, and HONO (+M) = OH + NO (+M). These new NH 2 /NO x /HO 2 and H 2 NO/NO x /HONO pathways play a critical role in promoting DME oxidation at intermediate temperatures. Novelty and Significance Statement: Blending NH 3 with DME can significantly enhance the reactivity of NH 3 and facilitate its practical application in advanced internal combustion engines. NH 3 /DME oxidation is studied in a novel supercritical pressure jet-stirred reactor up to 100 atm, a much higher pressure than previous studies. An interesting non-monotonic effect of NH3 addition on fuel oxidation has been found. Unique kinetic couplings of NH2/HO2/NOx and H2NO/NOx/HONO brough by NH3 and DME blending are identified to play important roles in radical generation and reactivity promotion. The valuable experimental data and key kinetics revealed in the current work can tremendously improve our understanding of NH 3 /DME oxidation via NO x /RO 2 and NH 2 / H 2 NO/HO 2 /NO x kinetic couplings at low to intermediate temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Evaluating the Impact of Off-Design CHP Performance on the Optimal Sizing and Dispatch on Hybrid Renewable-CHP Distributed Energy Resources

The maturation of distributed energy resources (DER) has prompted the exploration of their deployment in commercial building applications due to their potential to supply energy at lower costs and emissions rates compared to centralized generation. While several software tools exist for evaluating the techno-economic potential of integrated renewable energy and combined heat and power (CHP) systems for distributed generation applications, many suffer from poor accuracy in capturing off-design (part load and changes in ambient air temperature and pressure) performance characteristics of microturbines, combustion turbines, or internal combustion engines. Thus, this paper presents a methodology for integrating these off-design characteristics in the mixed-integer linear program within REopt, a hybrid DER screening tool. The economic impact of the CHP off-design performance is observed through several application studies of various hybrid system configurations in different climates. Each study indicates how CHP off-design performance influences optimal sizing and dispatch decisions and therefore overall system economic value. We observe through case studies that modeling without the off-design effects, depending on the CHP prime mover and site, can result in Net Present Value predictions of hybrid systems that can be overoptimistic in frequently hot climates (up to 52%), too conservative in frequently cold climates (up to 11%), or unaffected (+/-1%) in temperate climates. Cases also highlight several advantages of hybrid systems relative to non-hybrid systems such as total economic value and the systems' ability to mitigate potentially negative consequences attributed to off-design performance.

ambient de-rate↗
DOE OSTI2024

Levelized cost of charging of extreme fast charging with stationary LMO/LTO batteries

Extreme DC fast charging for electric vehicles (EVs) could be competitive with the internal combustion engine refueling experience and enable longer-distance travel, which could help with EV adoption and decarbonization, but these systems have high capital costs and extremely variable high-power demands. Behind-the-meter systems (BTMS) could support extreme-fast-charging (XFC) stations to increase nationwide adoption of EVs. Here, this study examines the optimal break-even levelized cost of charging (LCOC) across 96 BTMS scenarios to enable low-wait XFC stations providing 200 miles of charge in 10 min. This research simulates LCOC via synthetic XFC-capable EV loads, machine-learned battery life models from testing data, and nonlinear optimal controls, co-minimizing complex utility costs and battery replacements. An aggregate optimal BTMS design treating each EV load as equal likely gives an optimal LCOC per utility rate, the average of which is $\$$0.59/kWh. In addition, the sensitivity of optimal and off-optimal design factors, the long-life LMO/LTO chemistry, and optimized controls are analyzed. The battery control model, based on battery stressors to compare chemistries, optimizes LMO/LTO resting state of charge and cycle depth without compromising cost reduction, which enables greater flexibility in operation. The LCOC savings due to replacement reduction are small, up to $\$$0.035/kWh (6%), with an average of $\$$0.02/kWh (3.5%). Compared with gasoline stations, the aggregate XFC station design achieves comparable speed, experience of service, and cost at $\$$3.81/gal gasoline, showing that EVs can replace gasoline vehicles even for longer-distance travel.

25 ENERGY STORAGE↗
DOE OSTI2020

Quantifying the impacts of micro- and mild- hybrid vehicle technologies on fleetwide fuel economy and electrification

Micro- and mild-hybridization (jointly labeled as M-HEV) is gaining popularity as a cost-effective technology for fuel economy improvement, but whether and how M-HEV may compete against less efficient conventional internal combustion engine vehicles (ICEV), more efficient full hybrid electric vehicles (HEV), and plug-in electric vehicles (PEV) is not well understood. As such, this study aims at evaluating the impact of the market adoption of M-HEV on the average fuel economy of the new vehicle fleet and on the sales share of PEVs. The study reviews recent sales trends and market forecasts, and uses published estimates of manufacturing cost and fuel economy of M-HEV with an existing discrete choice model (Market Acceptance of Advanced Automotive Technologies or MA3T) to project the market penetration and impacts of M-HEV under different scenarios of M-HEV choice positions, designed to enhance conclusion robustness. It is found that among engine-based powertrain choices, micro-HEV appears to be the most cost-effective, followed by ICEVs, mild-HEV and finally full HEVs. M-HEV technologies are likely to improve fleetwide average fuel economy without significant adverse effects on sales of plug-in electric vehicles, and are likely to remain highly competitive outside PEVs through 2050.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Investigating the kinetic effect of prenol on iso -octane auto-ignition by means of an experimental and modeling study

A detailed experimental and kinetic modeling study was dedicated to understand the reported octane hyperboosting effect of prenol, by means of the measurement of the ignition delay times of its blends with iso -octane, and measurement of the mole fraction profiles of the fuels and intermediates inside the ULille rapid compression machine. Here, these results show that prenol addition leads to a reduction of the first-stage ignition phenomena and negative temperature coefficient behavior, which is only qualitatively captured by the model and is consistent with knock resistance improvement. It is suggested that this behavior is caused by two different factors. The first originates from gas-phase reactivity of prenol, and spans from the formation of unreactive unsaturated species through resonance-stabilized radicals, thereby constituting a competitive pathway for the radical pool generated by iso -octane. The second is of catalytic nature and cannot be captured by means of gas-phase kinetic modeling, but could also play an important role in the behavior of prenol in internal combustion engines.

42 ENGINEERING↗
DOE OSTI2023

An experimental and computational analysis of combustion heat release transformation in dual fuel combustion

Dual fuel (DF) diesel-methane combustion, which employs a high-reactivity fuel (diesel) to ignite a low-reactivity fuel (methane), is a widely studied combustion strategy for internal combustion engines, with significant potential for engine-out emissions reductions without the need for major hardware modifications. A phenomenon, which has been reported in the DF literature, but not explained fully, is the transformation of the shape of the apparent heat release rate (AHRR) curve as the start of injection (SOI) of diesel is advanced beyond a certain threshold; coincidentally, this AHRR transformation is usually accompanied by a sharp decrease in engine-out emissions of oxides of nitrogen (NOx). The goal of the present work is to establish the underlying physical reason(s) that cause the AHRR transformation. The AHRR transformation was observed on a single cylinder research engine (SCRE) at an indicated mean effective pressure (IMEP) of 5 bar at a speed of 1500 rev/min. The transformation occurred over a range of SOIs from 330 to 320 crank angle degrees (CAD). While the 330 CAD SOI exhibited a typical two-stage AHRR curve, with a clearly definable first-stage peak followed by a second-stage AHRR with little-to-no low temperature heat release (LTHR) present and high engine-out NOx, the 320 CAD SOI exhibited a single-stage, Gaussian-like AHRR curve, with noticeable LTHR and at least one order-of-magnitude lower NOx emissions. Here, leveraging analysis of experimental data and three-dimensional computational fluid dynamic simulations, the authors show that the AHRR transformation is impacted mainly by differences in local equivalence ratio distributions within the cylinder at ignition onset for different diesel SOIs.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Gaseous jet through an outward opening injector: Details of mixing characteristic and turbulence scales

Direct injection (DI) strategy of natural gas (NG) into internal combustion engines (ICE) has led to higher thermal efficiency and lower exhaust emissions. In order to thoroughly understand the most relevant phenomena affecting the performances of such engines, computational fluid dynamics (CFD) plays a key role as an accurate description of the jet evolution and interaction within the combustion chamber is required to that aim. Accurate description of high-pressure gaseous jets is rather challenging at high Mach numbers, as the injected gas is strongly under-expanded once in the ambient, giving room to shocks due to compressibility effects. Also the interaction between shock waves and mixing layers needs to be carefully represented with a multi-dimensional model, calling for substantial computational resources requirements. In this paper a numerical investigation of the behavior of a gaseous jet (Argon) through an outward opening injector has been carried out. A Large Eddy Simulation (LES) approach has been used in order to track the structures derived by the interaction of the injected fuel with the surrounding ambient. Although already good results were obtained using a Reynolds Averaged Navier-Stokes (RANS) approach, the adoption of LES is required to characterize more accurately the jet properties in terms of vortex structures and mixing effectiveness. Finally, the effect of the Nozzle Pressure Ratio (NPR) on the jet evolution has been highlighted in the paper, showing how a higher NPR would give a faster injection process, compromising however the homogeneity of the mixture.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

An energy model of droplet impingement on an inclined wall under isothermal and non-isothermal environments

The observation of spray-wall interaction is of great importance to understand the dynamics that occur during fuel impingement onto the chamber wall or piston surfaces in internal combustion engines. It is found that the maximum spreading length of an impinged droplet can provide a quantitative estimation of heat transfer and energy transformation for spray-wall interaction. Furthermore, it influences the air-fuel mixing and hydrocarbon and particle emissions at combusting conditions. In this paper, an analytical model of different droplet-wall impingement conditions is developed in terms of βm (dimensionless maximum spreading length, the ratio of maximum spreading length to initial droplet diameter) to understand the detailed impinging dynamic process. These conditions are grouped as: a single diesel droplet impinging on the wall with different inclined angles (α); cold wall - heated droplet and heated wall - cold droplet impingement when inclined angle of the wall is 0°, respectively. The analytical model is built up based on the energy conservation that considers kinetic energy, gravitation energy, and surface energy before impingement, as well as viscous dissipation, gravitation energy, adhesion energy, deformation energy, and heat energy after impingement. The experimental work of diesel droplet impinging on an inclined wall is performed at a certain range of the Weber number (We of 33 to 420) with various inclined angles (α of 0° to 45°), while for inclined angle is 0°, droplet and wall temperature are varied from 25°C to 150°C to study the effects of the inclined angle and temperature on the temporal evolution of the post-impingement characteristics (i.e. droplet spreading length, dynamic contact angle). The analytical model is validated and evaluated at the aforementioned experimental operating points. The validated model can be employed to predict maximum spreading length of the droplet impinged on the wall. It is further utilized to determine the transition from capillary regime to kinetic regime, then to viscous regime at different inclined angle of the wall.

42 ENGINEERING↗
DOE OSTI2020

Performance analysis of hybrid power configurations: Impact on primary energy intensity, carbon dioxide emissions, and life cycle costs

In this work, utilization of Natural gas and Hydrogen to support current and future building energy needs to offset the total electric demand while improving the grid resiliency and energy efficiency was investigated. Demand side energy management will play an important role in efficiently managing the available energy resources. Performance assessment of different power generation and energy management configurations is presented in this paper. Development of solutions in addressing grid resiliency by providing the ability to design suitable configurations for meeting individual building energy needs is discussed. Primary movers (PM) such as internal combustion engines (ICE) and fuel cells (FC) along with small scale auxiliary renewable energy source such as photovoltaics (PV) were considered. Key attributes of total carbon foot-print, life cycle costs including capital and operational expenditure, electric grid offset or peak shaving capability, thermal energy availability and its further potential to offset total electric demand, and primary energy intensity are analyzed and discussed in detail.

08 HYDROGEN↗
DOE OSTI2020

Distributed power generation via gasification of biomass and municipal solid waste: A review

The access to electricity has increased worldwide, growing from 60 million additional consumers per year in 2000-2012 to 100 million per year in 2012-2016. Despite this growth, approximately 675 million people will still lack access to electricity in 2030, indicating that electricity demand will continue to increase. Unfortunately, traditional large fossil power technologies based on coal, oil and natural gas lead to a major concern in tackling worldwide carbon dioxide emissions, and nuclear power remains unpopular due to public safety concerns. Distributed power generation utilizing CO 2 -neutral sources, such as gasification of biomass and municipal solid wastes (MSW), can play an important role in meeting the world energy demand in a sustainable way. Furthermore, this review focuses on the recent technology developments on seven power generation technologies (i.e. internal combustion engine, gas turbine, micro gas turbine, steam turbine, Stirling engine, organic rankine cycle generator, and fuel cell) suitable for distributed power applications with capability of independent operation using syngas derived from gasification of biomass and MSW. Technology selection guidelines is discussed based on criteria, including hardware modification required, size inflexibility, sensitivity to syngas contaminants, operational uncertainty, efficiency, lifetime, fast ramp up/down capability, controls and capital cost. Major challenges facing further development and commercialization of these power generation technologies are discussed.

09 BIOMASS FUELS↗
DOE OSTI2021

Experimental and computational study of the microporous layer and hydrophobic treatment in the gas diffusion layer of a proton exchange membrane fuel cell

Enabling fuel cell operation at high current density is critical for developing competitive alternative power system to replace internal combustion engine. However, liquid water management continues to be a challenge for high humidity or high current density operation. Water condensation in the porous media hinders efficient oxygen transport to the catalyst layer, which in turns, reduces fuel cell performance. To improve water management capability, the gas diffusion layer is often impregnated with Polytetrafluoroethylene (PTFE) and coated with a thin microporous layer, which have shown to improve fuel cell performance, especially under wet conditions. However, the fundamental mechanism that drives the performance enhancement is still not well understood. In this work, the effects of PTFE impregnation and MPL were studied using both experimental and computational techniques. Both limiting current and polarization tests under dry and wet operating condition are conducted to study the oxygen transport resistance and fuel cell performance. In addition, a 2-D, two-phase, multi-physics PEMFC model is developed to simulate performance and gain a fundamental understanding of local water saturation and oxygen concentration. The combined results show that 5 wt% PTFE impregnation with MPL significantly enhances liquid water management, which enables higher current density operation of a fuel cell.

25 ENERGY STORAGE↗
DOE OSTI2020

Effects of isoalcohol blending with gasoline on autoignition behavior in a rapid compression machine: Isopropanol and isobutanol

Alcohols, and particularly isoalcohols, are potentially advantageous blendstocks towards achieving efficient, low-carbon intensity internal combustion engines. Their use in advanced configurations, such as boosted spark-ignition or spark-assisted compression ignition, requires a comprehensive understanding of their blending effects on the low- and intermediate-temperature autoignition behavior of petroleum-derived gasoline. This work reports an experimental and modeling study of such autoignition characteristics quantified in a twin-piston rapid compression machine. Isopropanol and isobutanol are blended into a research-grade gasoline (FACE-F) at oxygenate blend levels of 0 to 30% vol/vol, with tests conducted at pressures of 20 and 40 bar, temperatures from 700 to 1000 K, and dilute stoichiometric fuel loadings. Changes to overall reactivity, including first-stage and main ignition times, and preliminary exothermicity are established, with comparisons made to previous measurements with ethanol-blended FACE-F gasoline. Furthermore, it is found that at low-temperature/NTC conditions (700–860 K) the isoalcohols suppress first-stage reactivity and associated heat release while main ignition times are extended. At NTC/intermediate-temperature (860–1000 K) conditions changes to fuel reactivity are less significant with isopropanol slightly suppressing reactivity and isobutanol promoting ignition. Detailed chemical kinetic modeling is used to interpret the experimental measurements. Overall trends of suppression or promotion in the blending behavior are reasonably captured by the model. Sensitivity and rate of production analyses indicate that at lower temperatures H-atom abstraction reactions from the surrogate fuel molecules (e.g., cyclopentane, isooctane) and the isoalcohols via OH are important leading to TC 3 H 6 OH and IC 4 H 8 OH–C radicals, for isopropanol and isobutanol respectively, which act as scavengers in the system. At higher temperatures, similar chemistries are dominant, but there is an increasing importance of abstraction by HO 2 . The kinetic modeling also indicates that the promoting effect of isobutanol at higher temperatures is due to the increased abstractions at the γ-sites, while at lower temperatures abstraction at the α-site leads to greater reactivity suppression.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the interplay between pilot fuel mixing and auto-ignition chemistry in hydrogen-enriched environment

The diesel-piloted dual-fuel compression ignition combustion strategy is well-suited to accelerate the decarbonization of transportation by adopting hydrogen as a renewable energy carrier into the existing internal combustion engine with minimal engine modifications. Despite the simplicity of engine modification, many questions remain unanswered regarding the optimal pilot injection strategy for reliable ignition with minimum pilot fuel consumption. The present study uses a single-cylinder heavy-duty optical engine to explore the phenomenology and underlying mechanisms governing the pilot fuel ignition and the subsequent combustion of a premixed hydrogen-air charge. The engine is operated in a dual-fuel mode with hydrogen premixed into the engine intake charge with a direct pilot injection of n-heptane as a diesel pilot fuel surrogate. Optical diagnostics used to visualize in-cylinder combustion phenomena include high-speed IR imaging of the pilot fuel spray evolution as well as high-speed HCHO* and OH* chemiluminescence as indicators of low-temperature and high-temperature heat release, respectively. Three pilot injection strategies are compared to explore the effects of pilot fuel mass, injection pressure, and injection duration on the probability and repeatability of successful ignition. The thermodynamic and imaging data analysis supported by zero-dimensional chemical kinetics simulations revealed a complex interplay between the physical and chemical processes governing the pilot fuel ignition process in a hydrogen containing charge. Hydrogen strongly inhibits the ignition of pilot fuel mixtures and therefore requires longer injection duration to create zones with sufficiently high pilot fuel concentration for successful ignition. Results show that ignition typically tends to rely on stochastic pockets with high pilot fuel concentration, which results in poor repeatability of combustion and frequent misfiring. In conclusion, this work has improved the understanding on how the unique chemical properties of hydrogen pose a challenge for maximization of hydrogen’s energy share in hydrogen dual-fuel engines and highlights a potential mitigation pathway.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Insight into premixed diethoxymethane flames: Laminar burning velocities, temperatures, and emissions behaviour

Diethoxymethane ((CH 3 CH 2 O) 2 CH 2 , DEM) is a promising carbon-neutral fuel. DEM is a diether or acetal with a molecular structure similar to oxymethylene ethers (CH 3 O–(CH 2 O)n–CH 3 , OME n ). Thus, DEM can be expected to have a similar combustion behavior to OMEs, reducing harmful emissions such as NO x and particulate matter (PM) in internal combustion engines. From both experimental and kinetic modeling, fundamental studies on DEM are scarce in the literature. More studies are required to gain a detailed insight into the oxidation kinetics of DEM. Laminar burning velocity (LBV) is a critical property that allows a detailed assessment of the potential application of DEM in combustion devices. Unfortunately, the literature on the LBV of DEM is limited. Therefore, in this study we have investigated the LBV of DEM using two reactors for the first time, namely a heat flux burner and a combustion chamber. The experimental data is reported for equivalence ratio between 0.7 and 1.7, initial temperatures of 368–423 K, and initial pressure of 1–5 bar. In addition, we developed a detailed kinetic model extending our recent work of Shrestha et al. (Combust. Flame. 246 (2022) 112,426) to characterize the combustion behavior of DEM utilizing the new experimental data from this work and the literature data. Our model performs remarkably well in capturing the newly measured LBV experimental data over various experimental conditions. We found that DEM and dimethoxy methane (DMM) have similar values of LBVs (within ±1.5 cm/s) for a given condition, which indicates that intermediate chemistry governs the flame chemistry. Despite DEM being a larger molecule that is expected to have slightly lower LBVs than DMM, its effect on the measured values of LBVs is negligible. Finally, we experimentally measured NO x formation in DEM flame for the first time. The stochiometric flame has the highest NO x formation. The proposed model predicted the equivalence ratio dependence of NO x nicely. However, it overestimates the NO x formation for stoichiometric DEM/air mixtures by ~30 %. The model suggests that the thermal NO formation route is favored at lean and stochiometric conditions. In contrast, the prompt NO formation route is enhanced for rich mixtures.

10 SYNTHETIC FUELS↗