Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering prototypes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

CMS HGCAL ECON-D ASIC : Impact of CMOS fabrication process tuning on performance and radiation tolerance

The CMS experiment’s High Granularity Calorimeter (HGCAL) upgrade will replace CMS’s existing endcap calorimeters in preparation for the High Luminosity LHC. To effectively use over 6 million channels of this “imaging”calorimeter, CMS has developed two novel Endcap Concentrator (ECON) ASICs to perform data compression/selection on detector. The ECON-D ASIC operates on the 750kHz data path, and the ECON-T ASIC on the 40MHz trigger path. These 65 nm CMOS ASICs are radiation tolerant to 200 Mrad and low power, operating at less than 2.5 mW/channel. The first full-functionality prototype ECONs were produced and characterized in 2021-23, and an initial engineering run was performed in 2024. ECON-D radiation testing for the engineering run revealed that the chip’s internal SRAMs produce intermittent read errors for a non-negligible fraction of chips. Further investigation indicated that the SRAM performance is highly sensitive to the exact parameters of the CMOS fabrication process. To both study this process sensitivity and mitigate SRAM performance issues, twenty ECON wafers were produced in 2025 with a range of doping concentrations designed to tune the underlying transistor threshold voltage by 0%, 5%, 10%, and 15% from nominal. This talk will present first measurements of ECON-D performance, power consumption, and radiation tolerance for these four variations of CMOS process.

Syal, Chinar [Fermilab]↗
DOE OSTI2023

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for highly loaded structures in harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects due to the marine environment. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at the Pacific Northwest National Laboratory's Marine and Coastal Research Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗
DOE OSTI2024

Development of a Light-Trapping, Planar-Cavity Receiver for Enclosed Solar Particle Heating

Concentrating solar thermal power (CSP) technology development has recently focused on high efficiency power cycles and chemical reactions that require high operating temperatures. An increase in receiver operating temperatures relative to current commercial CSP technology is necessary to support more efficient, high temperature power cycles or thermochemical processes. Solar receivers operating with heat transfer media temperatures >700 degrees C face various challenges including thermal performance, scalability, thermal-mechanical issues, and receiver service life. In addition, heat transfer media selection for high-temperature processes has been moving towards inert solid particles in Gen3 CSP, and reactive solid media and/or gases in solar thermochemical processes. To overcome the shortcomings and limitations of conventional designs for molten salt or particle receivers and receiver reactors, we introduce a unique light-trapping, planar cavity receiver (LTPCR) configuration and will present the current development progresses to demonstrate receiver feasibility through modeling, testing, and prototype demonstration.

ENGINEERING,SOLAR ENERGY↗
DOE OSTI2021

Radiative lifetime-encoded unicolour security tags using perovskite nanocrystals

Traditional fluorescence-based tags, used for anticounterfeiting, rely on primitive pattern matching and visual identification; additional covert security features such as fluorescent lifetime or pattern masking are advantageous if fraud is to be deterred. Herein, we present an electrohydrodynamically printed unicolour multi-fluorescent-lifetime security tag system composed of lifetime-tunable lead-halide perovskite nanocrystals that can be deciphered with both existing time-correlated single-photon counting fluorescence-lifetime imaging microscopy and a novel time-of-flight prototype. We find that unicolour or matching emission wavelength materials can be prepared through cation-engineering with the partial substitution of formamidinium for ethylenediammonium to generate “hollow” formamidinium lead bromide perovskite nanocrystals; these materials can be successfully printed into fluorescence-lifetime-encoded-quick-read tags that are protected from conventional readers. Furthermore, we also demonstrate that a portable, cost-effective time-of-flight fluorescence-lifetime imaging prototype can also decipher these codes. A single comprehensive approach combining these innovations may be eventually deployed to protect both producers and consumers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mono‐Materials Created by Engineering a Continuum of P3HB Stereomicrostructures in a One‐Step Catalytic Process

Multi-material products that combine multiple complementary polymers can create products with desired performance but present challenges to end-of-life (EoL) management. The emerging mono-material product design based on a single polymer type addresses the fundamental EoL issue, but challenges of delivering vastly tunable material properties by the single polymer still remain. Here, we introduce a simple strategy to produce biodegradable poly(3-hydroxybutyrate) (P3HB) materials with a wide range of material properties by engineering a stereomicrostructure continuum, achieved through polymerizing diastereomeric mixtures of racemic and meso-dimethyl diolides at various feed ratios with a single catalyst. This one-step, one-pot process produces biodegradable P3HB mono-materials ranging from rigid to flexible thermoplastics, to tough thermoplastic elastomers, to a pressure-sensitive adhesive (PSA), which have been then combined to fabricate prototype all-P3HB PSA tapes, demonstrating the feasibility of designing mono-material products through engineering polymer stereomicrostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Development of High-Performance Cast Crankshafts. Final Technical Report

The objective of this project was to develop technologies that would enable the production of cast crankshafts that can replace high performance forged steel crankshafts. To achieve this, the Ultimate Tensile Strength (UTS) of the new material needs to be 850 MPa with a desired minimum Yield Strength (YS; 0.2% offset) of 615 MPa and at least 10% elongation. Perhaps more challenging, the cast material needs to be able to achieve sufficient local fatigue properties to satisfy the durability requirements in today’s high performance gasoline and diesel engine applications. The project team focused on the development of cast steel alloys for application in crankshafts to take advantage of the higher stiffness over other potential material choices. The material and process developed should be able to produce high-performance crankshafts at no more than 110% of the cost of current production cast units, perhaps the most difficult objective to achieve. To minimize costs, the primary alloy design strategy was to design compositions that can achieve the required properties with minimal alloying and post-casting heat treatments. An Integrated Computational Materials Engineering (ICME) based approach was utilized, rather than relying only on traditional trial-and-error methods, which has been proven to accelerate alloy development time. Prototype melt chemistries designed using ICME were cast as test specimens and characterized iteratively to develop an alloy design within a stage-gate process. Standard characterization and material testing was done to validate the alloy performance against design targets and provide feedback to material design and manufacturing process models. Finally, the project called for Caterpillar and General Motors (GM) to develop optimized crankshaft designs using the final material and manufacturing processing path developed. A multi-disciplinary effort was to integrate finite element analyses by engine designers and geometry-specific casting simulations with existing materials models to optimize crankshaft cost and performance. Prototype crankshafts of the final design were to be produced and validated using laboratory bench testing and on-engine durability testing. ICME process simulation tools were used to investigate a broad range of processing concepts. These concepts included casting orientation, various mold and core materials, and various filling and feeding strategies. Each crankshaft was first simulated without gating and risers, which is termed natural solidification. The natural solidification results were used as a baseline for strategy development of each concept. Casting process simulations and ICME tools were proven to be reasonable predictors of real world results. Potential alloys were developed that could meet the project material property goals with appropriate normalization and temper treatments. For the alloys considered, post-normalization temper treatments proved to be necessary to achieve the desired yield strengths and elongations and appropriate heat treatments were designed using ICME tools. The experimental data of all the alloys were analyzed in combination with ICME tools to establish chemistry-process-structure relations. Several GM small gas engine (SGE) crankshafts were successfully cast in sand molds using two different sprue, runner, gate, riser, chill designs. These crankshafts were cast in two different steel alloys developed during the project, but casting finishing (e.g. riser removal) remains a cost challenge. A long list of future work was left unfinished when this project was unexpectedly terminated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Carbon-negative production of acetone and isopropanol by gas fermentation at industrial pilot scale

Many industrial chemicals that are produced from fossil resources could be manufactured more sustainably through fermentation. In this work, we describe the development of a carbon-negative fermentation route to producing the industrially important chemicals acetone and isopropanol from abundant, low-cost waste gas feedstocks, such as industrial emissions and syngas. Using a combinatorial pathway library approach, we first mined a historical industrial strain collection for superior enzymes that we used to engineer the autotrophic acetogen Clostridium autoethanogenum. Next, we used omics analysis, kinetic modeling and cell-free prototyping to optimize flux. Finally, we scaled-up our optimized strains for continuous production at rates of up to ~3 g/L/h and ~90% selectivity. Life cycle analysis confirmed a negative carbon footprint for the products. Unlike traditional production processes, which result in release of greenhouse gases, our process fixes carbon. These results show that engineered acetogens enable sustainable, high-efficiency, high-selectivity chemicals production. We expect that our approach can be readily adapted to a wide range of commodity chemicals.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Horn Location Sensors for LBNF

Updates on Prototype of the HLS system for LBNF. This poster is meant for the Engineers' Retreat.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

Transmutation Fuels Development in the Advanced Fuels Campaign

Metallic fuels have a history of use that spans the entire nuclear age, especially in association with the development of the LMFBR. Initially, metallic fuels were employed due to their ease of fabrication and high heavy metal density (which led to the most favorable breeding efficiencies in fast reactors). During subsequent decades of use, metallic fuel technology has matured significantly, leading to the realization of major benefits in the areas of fuel reliability and burnup, proliferation-resistant recycling, remote fabrication, and passive reactor safety. Such characteristics continue to make metallic fuels a highly attractive technology, especially for use with future sodium fast reactors. Current research and development activities on metallic fuels in DOE's Advanced Fuels Campaign are focused on their potential use for actinide transmutation in advanced SFRs. In such a mission, metallic fuels would be employed as part of a closed fuel cycle into which plutonium and minor actinides (Am, Np) recovered from LWR spent fuel would be incorporated. All actinides in this metallic fuel would be fissioned or transmuted in a fast reactor to eliminate the extremely long-lived, heat-producing actinides in order to reduce the volume, heat load, and radio-toxicity burden on a future geological repository. Thus, the need exists to demonstrate reliable performance of metallic fuels with Pu and minor actinide constituents to very high burnup. As part of this application, there is also a need for a near zero-loss fabrication process, since losses during fuel fabrication are a potential source of long-lived actinides destined for geologic disposal. This paper presents the current state and future direction of the development of metallic fuels for actinide transmutation in the US. Metallic fuels have had a long history of use in sodium-cooled fast reactors. Continued research, development, and design innovation over a period of decades have demonstrated this fuel technology to be safe and reliable to extremely high burnups over a wide range of compositions. Their simple fabrication has historically given them a significant economic advantage over other fuel forms. Research and development on metallic fuels continues, with particular emphasis on showing that this fuel technology can incorporate significant quantities of plutonium and minor actinides for the purpose of efficiently and economically transmuting these elements in a fast-spectrum reactor. New fabrication methods to improve retention of the volatile fuel constituents during the casting process (and reduce waste generation), are being developed. Irradiation testing of the new metallic fuels has so far indicated that the new compositions, although differing significantly both in the quantities of Pu and minor actinides included and in the Zr alloying addition, perform as a function of fission density very analogously to the historic U-Zr and U-Pu-Zr fuels. In the next few years it is anticipated that a new casting furnace prototype will demonstrate that these new metallic fuel alloys can be fabricated at engineering scale, in a remote environment, with no significant fuel loss or waste generation. Irradiation tests currently underway will provide the performance data needed to assess fuel reliability/burnup capability and identify any unique behaviors that are a result of the new compositions. If these future results are consistent with the intermediate data available at present, metallic fuels are expected to continue to be a strong contender for the fuel technology choice of future fast reactors. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Towards a Standard Process Management Infrastructure for Workflows Using Python

Orchestrating the execution of ensembles of processes lies at the core of scientific workflow engines on large scale parallel platforms. This is usually handled using platform-specific command line tools, with limited process management control and potential strain on system resources. The PMIx standard provides a uniform interface to system resources. The low level C implementation of PMIx has hampered its use in workflow engines, leading to the development of Python binding that has yet to gain traction. In this paper, we present our work to harden the PMIx Python client, demonstrating its usability using a prototype Python driver to orchestrate the execution of an ensemble of processes. We present experimental results using the prototype on the Summit supercomputer at Oak Ridge National Laboratory. This work lays the foundation for wider adoption of PMIx for workflow engines, and encourages wider support of more PMIx functionality in vendor provided system software stacks.

Elwasif, Wael↗
DOE OSTI2019

Low Cost Hydrogen Storage at 875 Bar Using Steel Liners and Steel Wire Wraps

The Department of Energy’s (DOE) Fuel Cell Technologies Office (FCTO) within the Office of Energy Efficiency and Renewable Energy (EERE) supports research and development activities leading to the development of low-cost, high-pressure hydrogen storage systems for use in hydrogen refueling stations (forecourt). The specific goals of this project were to develop and produce a prototype of a pressure vessel to safely store gaseous hydrogen at 875 bar that meets the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Section VIII, Division 3 design code for service in hydrogen (Article KD-10) and meets the DOE storage tank cost target of <$1000/kg stored hydrogen (H 2 ). The pressure vessel designed and prototyped as part of this study utilizes a standard ASME approved, 406 mm diameter, 31.7 mm thick wall, and 9.14m long, liner with a capacity of 765 liters and rated for a pressure of up to 460 bar. The liner was wrapped with high strength steel wires to boost its pressure rating to 875 bars. The process of wrapping metal liners with a high strength steel wire, a WireTough patented technology, was first demonstrated on short cylinders that were 1.9 m long but of the same diameter and wall thickness as the 9.1 m long, 765 L cylinders. Subsequently, full length cylinders that were 9.14 m long were designed and certified under the applicable ASME Design Codes. Two prototype cylinders were wire wrapped to demonstrate the manufacturability. Following is a bulleted summary of the accomplishments of the project that ended on August 31, 2018.

25 ENERGY STORAGE↗
DOE OSTI2021

On the progress of 3D-printed hydrogels for tissue engineering

Additive manufacturing or more commonly known as 3D printing, is currently driving innovations and applications in diverse fields such as prototyping, manufacturing, aerospace, education, and medicine. Recent technological and materials research breakthroughs have enabled 3D bioprinting, where biomaterials and cells are used to create scaffolds and functional living tissues (e.g. skin, cartilage, etc.). This prospective focuses on the classification and applications of hydrogels, and design considerations in their production (i.e. physical and biological parameters). Herein, the materials for 3D printing of hydrogels, such as biopolymers, synthetic polymers, and nanocomposites, are mainly discussed. More importantly, future perspectives on 3D printing hydrogels including new materials, 4D printing, emerging printing technologies, etc. and their importance in biomedical and bioengineering applications are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Final CTAP Report

Sandia will provide technical assistance to Helpful Engineering to develop and test the Universal Citizen Protection Device (UCPD) which is a UV-based filter-less PPE concept that aims to keep the Sars-CoV-2 virus out of eyes, nose and mouth with a 99%+ reliability. The heart of the device would be a concealed UV Chamber that decontaminates all air going in and out of the PPE. Helpful Engineering’s goal is to build this device to be reusable and cost less than $100 to construct and can be worn for 8 hours. The UCPD is an open source project, and once developed, prototyped, tested and approved, it will be shared with interested manufacturers globally.

42 ENGINEERING↗
DOE OSTI2019

LGFCS Prototype System Testing (Final Report)

In the project, LGFCS assembled and tested its modular SOFC Power System that incorporates all critical technology improvements identified for its “product-like” demonstration. This product demonstrator is expected to meet customer and LGFCS performance expectations for operation, availability, durability and serviceability. The principal technology improvements are aimed at increasing the fuel cell power output and reducing the stack degradation rate. Improvements were also made for added system robustness and increased reliability. The objective of this program is to test a 250kWe thermally self-sustaining modular solid oxide fuel cell (SOFC) Power System for a minimum of 5,000 hours while advancing this commercial prototype product demonstrator to a Technical Readiness Level (TRL) 7. The SOFC system was tested on a site provided by Stark State College in North Canton, Ohio. System performance and degradation as well as cost estimates were compared to established SOFC Program performance metrics to assess progress. The major achievements were to assemble, and QA qualify 70 fuel cell strips for 12 integrated blocks into a fuel cell vessel and install it into a generator module with the fuel and power electronics modules on the test site. Performance to date included over 1800 hours on load at 250 KWAC to the grid with a DC efficiency of 61% and AC efficiency of 55%. Power degradation was less than 0.4% per 1000 hours and NOx emissions met standards. The LGFCS SOFC Prototype System (GEN0) was demonstrated in an operational environment and therefore achieving Technical Readiness Level 7. The work presented here represents the efforts of all the employees of LG Fuel Cell Systems. Their dedication and hard work made GEN0 possible and successful.

03 NATURAL GAS↗
DOE OSTI2022

Toward a glycyl radical enzyme containing synthetic bacterial microcompartment to produce pyruvate from formate and acetate

Formate has great potential to function as a feedstock for biorefineries because it can be sustainably produced by a variety of processes that don’t compete with agricultural production. However, naturally formatotrophic organisms are unsuitable for large-scale cultivation, difficult to engineer, or have inefficient native formate assimilation pathways. Thus, metabolic engineering needs to be developed for model industrial organisms to enable efficient formatotrophic growth. Here, we build a prototype synthetic formate utilizing bacterial microcompartment (sFUT) encapsulating the oxygen-sensitive glycyl radical enzyme pyruvate formate lyase and a phosphate acyltransferase to convert formate and acetyl-phosphate into the central biosynthetic intermediate pyruvate. This metabolic module offers a defined environment with a private cofactor coenzyme A that can cycle efficiently between the encapsulated enzymes. To facilitate initial design-build-test-refine cycles to construct an active metabolic core, we used a “wiffleball” architecture, defined as an icosahedral bacterial microcompartment (BMC) shell with unoccupied pentameric vertices to freely permit substrate and product exchange. The resulting sFUT prototype wiffleball is an active multi enzyme synthetic BMC functioning as platform technology.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Construction status of the Mu2e crystal calorimeter

The Mu2e experiment at Fermilab will search for the charged-lepton flavor violating neutrino-less conversion of a negative muon into an electron in the field of an aluminum nucleus. The Mu2e detector is composed of a tracker, an electromagnetic calorimeter and an external veto for cosmic rays. The calorimeter plays an important role in providing excellent particle identification capabilities and a fast online trigger filter, while aiding the track reconstruction capabilities. Calorimeter requirements are to provide a large acceptance for 0~10 MeV electrons and reach: i) a time resolution better than 0.5 ns; ii) an energy resolution better than 10%; and iii) a position resolution of 1 cm. The calorimeter consists of two disks, each one made of 674 pure CsI crystals. Each crystal is readout by two large area 2×3 arrays of UV-extended SiPMs of 6×6 mm2 dimensions. A large scale prototype (Module-0) has been tested at an electron beam. We report here the tests done to finalize the calorimeter design, the results obtained with Module-0 and the status of production. At this time, the performance characteristics of 85% of the crystals and all of the SiPMs have been measured. The calorimeter engineering drawings have been completed and the large mechanical components are under fabrication. Analog and digital electronics have been prototyped and tested with irradiation dose. Their serial production is being organized. The calorimeter assembly phase is planned for mid-2020.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

JPype

JPype is a Python module to provide full access to Java from within Python. It allows Python to make use of Java only libraries, exploring and visualization of Java structures, development and testing of Java libraries, scientific computing, and much more. By gaining the best of both worlds using Python for rapid prototyping and Java for strong typed production code, JPype provides a powerful environment for engineering and code development. This is achieved not through re-implementing Python, as Jython has done, but rather through interfacing at the native level in both virtual machines. This shared memory based approach achieves decent computing performance, while providing the access to the entirety of CPython and Java libraries.

Nelson, KarlE.↗