Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Cost-constrained adaptive simulations of transient spray combustion in a gas turbine combustor

Predictive high-fidelity simulations of turbulent spray combustion must capture the combined effects of complex chemistry, multiphase evaporating flow and spray-flame interactions to achieve physical accuracy. Finite-rate chemistry (FRC) combined with a realistic chemical mechanism is a combustion model well-suited for this purpose, but has a high computational cost due to the large number and stiffness of transported chemical species. In contrast, flamelet-based models achieve lower cost by transporting a small number of quantities of reduced stiffness, but assumptions regarding local flame topology, boundary conditions and inter-phase coupling limit their physical accuracy. Recently, the Pareto-efficient combustion (PEC) framework was developed to dynamically assign combustion models based on local cost and accuracy metrics in gas-phase reacting flows. In this work, we extend this PEC framework to spray combustion through the rigorous analysis of the multiphase coupling terms in the governing equations. The derivation shows that spray evaporation causes errors in the prediction of species mass fractions for flamelet-based models due to the sensitivity of the local thermo-chemical state to changes in composition caused by fuel vaporization across combustion regimes present in practical spray combustion devices. Sub-model assignment is formulated as a multiple-choice knapsack problem, where computational cost is directly controlled through the fraction of the domain assigned to the FRC sub-model. The extended PEC formulation is applied to the simulation of a realistic rich-quench-lean gas turbine combustor at steady-state conditions, as well as transient operation resulting in lean blow-out (LBO). Analysis of transient simulations during LBO demonstrates the extended PEC formulation’s capacity to dynamically adapt to changing conditions within the combustor. Transient combustor dynamics are shown to approach convergence with limited increases in computational cost, while retaining substantial computational cost reduction compared to monolithic FRC simulations. Through PEC simulations with increasing fractions of the domain assigned to FRC, monolithic flamelet simulations are shown to over-predict flame stability during LBO. Finally, the extended PEC formulation is thus shown to overcome deficiencies of monolithic models by controlling modeling error for multiphase combustion modeling.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

HTR-1.3 solver: Predicting electrified combustion using the hypersonic task-based research solver

Here this manuscript presents an updated open-source version of the Hypersonics Task-based Research (HTR) solver. The solver, whose main features are presented in Di Renzo et al. (2020) and Di Renzo & Pirozzoli (2021), is designed for direct numerical simulation of reacting flows at high Reynolds numbers. This new version extends the applications of the HTR solver to turbulent combustion in the presence of external electric fields. In particular, a new distributed Poisson solver compatible with heterogeneous architectures has been incorporated in the algorithm to compute the electric potential distribution in bi-periodic configurations. The drift fluxes of the electrically charged species are now included in the transport equations using a targeted essentially non-oscillatory scheme. A verification of these new features of the solver is provided using one-dimensional burner stabilized flames, whereas a three dimensional turbulent flame is utilized to discuss the scalability of the proposed numerical tool.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Design and Modeling of an 80 bar Oxy-Combustor for Direct Fired Supercritical CO2 Applications

As supercritical CO2 power cycles for fossil energy power generation continue to generate interest, there are significant issues and unanswered questions regarding injector design, flame stabilization, wall heat transfer, CO emissions, combustion dynamics and other combustion phenomenon. For natural gas, direct-fired cycles with carbon capture it is believed that Computational Fluid Dynamics (CFD) modeling will play an essential role in the combustor design process. To accurately model turbulent reacting flows at these unique conditions, experimental data is needed to validate CFD codes and sub-models and is currently lacking at conditions relevant for these cycles. This paper presents the conceptual design and CFD simulations of an experimental 80 bar oxy-combustion facility and test article currently under construction at NETL. The facility is targeted towards the testing of a single injector, direct-fired sCO2 combustor at the 100 kW thermal output level. While these conditions do not reflect the actual Allam cycle operating conditions (300 bar) they are viewed as a stepping stone in the model validation process at supercritical conditions. Reynolds Averaged Navier-Stokes as well as Large Eddy Simulation are used to model the turbulent combustion process and aid in the design of the combustor and injector. Process parameters including oxidizer preheat temperature and combustor flowrate are investigated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Performance and flexibility improvements of Staged Pressurized Oxy-Combustion

Staged Pressurized Oxy-Combustion (SPOC) is a low-carbon coal combustion power technology being developed by Washington University in St. Louis (WUSTL). Oxy-combustion plants enable straightforward capture of carbon dioxide (CO 2 ) by removing most of the nitrogen in the combustion air prior to use, thereby burning fuel in near-pure oxygen instead of air, producing a flue gas containing primarily CO 2 and water. CO 2 capture at amounts > 90% is possible, often using cryogenic air separation. Oxy-combustion typically relies on flue gas recycle (FGR) to reduce the peak temperature and radiation that would otherwise occur in a fuel/oxygen only flame. SPOC reduces the peak temperatures of combustion by utilizing two or more pressurized boiler modules connected in series to produce fuel staging; hence, only a portion of the fuel is combusted in any given furnace module. This means that the thermal energy released at each stage can be captured and removed from the gases prior to subsequent stages, when more fuel is introduced. This allows the SPOC process to operate with minimal FGR, avoiding the associated efficiency losses and additional costs. Also, the process operates at an elevated gas-side pressure, reducing boiler size, enhancing heat transfer to achieve a compact boiler configuration as compared to an atmospheric-pressure boiler design, and allowing for recovery of the latent heat of the water from the flue gas at a temperature useful to the steam cycle. The resultant net efficiency of the system is over 3 percentage points greater than traditional atmospheric-pressure oxy-combustion, and 7 percentage points greater than the post combustion variant, representing a step-change improvement over first-generation capture technologies. To further develop the concept, WUSTL and the Electric Power Research Institute, Inc., organized a project with American Air Liquide, Inc., Doosan Babcock Limited, and the U.S. Department of Energy to investigate a practicable and workable boiler design. The team has identified the potential for enhanced process flexibility for controlling power generation over a wider load range than is normally available to conventional coal-fired power plants due to the staged nature of the heat release. With increasing intermittent renewable generator contribution, on-demand generators need to be highly flexible to participate in the future energy market, requiring extensive operation at reduced load. Conventional coal-fired steam generators typically face challenges in maintaining temperature control of the reheat steam and main steam at reduced loads. This results in inefficient operation, both in terms of the boiler efficiency and steam turbine heat rate. The results of this project show the SPOC process is capable of exceptional turndown, both on a stage basis and with the ability to bypass entire stages. Oxygen-supply flexibility was also investigated, as this is also a key consideration for the overall flexibility of the SPOC process given the operating constraints of conventional air separation units. A boiler design concept assessment was conducted and was focused on delivering compact and constructible design. The assessment checked appropriate tube operating metal temperatures at full load and at lower operating loads, balanced against the needs of efficient coal combustion, and the resultant slagging and ash environments. Combustion testing in the 100-kWth pressurized combustion test rig at WUSTL was carried out to validate the combustion, heat flux profiles and burnout at multiple loads. Combustion parameters investigated were flame stability, fuel burnout, ash composition, radiative heat flux, and temperature profiles. The results of these tests formed the basis of a full-scale boiler design that will encompass improvements in both efficiency and flexibility over conventional oxy-combustion processes. The air separation unit flexibility was investigated, and associated cost implications were addressed. Detailed economic assessment results for a 550 MWe net power block are also provided, allowing for a comparison against the baseline NETL oxy-combustion and post combustion capture cases.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Optimizing and commercializing the LBNL Grid Burner for AO Smith Storage Water Heater

The purpose of this project was to demonstrate that the LBNL Ring Burner technology can meet the operating, performance, and emission requirements while operating in a residential appliance. This project successfully met all performance targets and enhanced flame stability of the Ring Burner technology.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Demonstration of Multi-Gamma Based Sensor Technology for As-Fired Coal Property Measurement

This project demonstrated the application of the use of an advanced multigamma attenuation (MGA) sensor to accurately and precisely measure coal properties at the point of injection into burners. Accurate and precise coal property information at the burner provides the opportunity to adjust burner parameters to better follow changing load condition, optimize flame stability, and decrease nitrogen oxide formation at each burner. In addition, coal property information at the burner will assist in managing slag flow behavior, fireside ash related deposition, corrosion, and erosion issues. The advantage of having multiple gamma emitters is that the atomic/elemental interaction with the gamma energy takes place at several energies and the resulting attenuation is dependent upon the atomic number of the atom/element encountered in the coal.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Impact of particle size and particle-flow-wall coupling on pressurized oxy-combustion in the down-fired burner

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new coal combustion technologies. Because of the high pressure, the volume fraction of coal particles at the fuel inlet of the burner of a pressurized oxy-combustor is close or even higher than the maximum limit that commercial CFD codes (e.g., ANSYS FLUENT) can handle. At this high particle volume fraction, the interactions among particles, fluid flow, and wall need to be re-evaluated. The present computational work is the first step of a systematic analysis of the particle influence, like releasing method, releasing locating, and particle size, in a pilot-scale POC combustor, developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. Specifically, a 15-bar, 100 kWth, POC combustor is modeled employing ANSYS FLUENT, using Reynolds-averaged Navier-Stokes (RANS) modeling. It is revealed that for this pilot-scale, pressurized burner, velocity profiles of the near-wall region in this POC facility exhibit some discrepancy against the near-wall turbulent flow velocity profile. In order to investigate the particle influence in the near-wall region, particle releasing location will be investigated. Numerical simulation results exhibit the coupling effect of turbulence flow and particles in this case. The particle size also demonstrates a great effect on particle trajectory, then further has an impact on flame stability and temperature.

Li, Lei↗
DOE OSTI2024

LES and RANS Spray Combustion Analysis of OME 3-5 and n-Dodecane

Clean-burning oxygenated and synthetic fuels derived from renewable power, so-called e-fuels, are a promising pathway to decarbonize compression–ignition engines. Polyoxymethylene dimethyl ethers (PODEs or OMEs) are one candidate of such fuels with good prospects. Their lack of carbon-to-carbon bonds and high concentration of chemically bound oxygen effectively negate the emergence of polycyclic aromatic hydrocarbons (PAHs) and even their precursors like acetylene (C 2 H 2 ), enabling soot-free combustion without the soot-NO x trade-off common for diesel engines. The differences in the spray combustion process for OMEs and diesel-like reference fuels like n-dodecane and their potential implications on engine applications include discrepancies in the observed ignition delay, the stabilized flame lift-off location, and significant deviations in high-temperature flame morphology. For CFD simulations, the accurate modeling and prediction of these differences between OMEs and n-dodecane proved challenging. This study investigates the spray combustion process of an OME 3 − 5 mixture and n-dodecane with advanced optical diagnostics, Reynolds-Averaged Navier–Stokes (RANS), and Large-Eddy Simulations (LESs) within a constant-volume vessel. Cool-flame and high-temperature combustion were measured simultaneously via high-speed (50 kHz) imaging with formaldehyde (CH 2 O) planar laser-induced fluorescence (PLIF) representing the former and line-of-sight OH* chemiluminescence the latter. Both RANS and LES simulations accurately describe the cool-flame development process with the formation of CH 2 O. However, CH 2 O consumption and the onset of high-temperature reactions, signaled by the rise of OH* levels, show significant deviations between RANS, LES, and experiments as well as between n-dodecane and OME. A focus is set on the quality of the simulated results compared to the experimentally observed spatial distribution of OH*, especially in OME fuel-rich regions. The influence of the turbulence modeling is investigated for the two distinct ambient temperatures of 900 K and 1200 K within the Engine Combustion Network Spray A setup. The capabilities and limitations of the RANS simulations are demonstrated with the initial cool-flame propagation and periodic oscillations of CH 2 O formation/consumption during the quasi-steady combustion period captured by the LES.

CFD↗
NASA NTRS1976

Reduction of gaseous pollutant emissions from gas turbine combustors using hydrogen-enriched jet fuel

Recent progress in an evaluation of the applicability of the hydrogen enrichment concept to achieve ultralow gaseous pollutant emission from gas turbine combustion systems is described. The target emission indexes for the program are 1.0 for oxides of nitrogen and carbon monoxide, and 0.5 for unburned hydrocarbons. The basic concept utilizes premixed molecular hydrogen, conventional jet fuel, and air to depress the lean flammability limit of the mixed fuel. This is shown to permit very lean combustion with its low NOx production while simulataneously providing an increased flame stability margin with which to maintain low CO and HC emission. Experimental emission characteristics and selected analytical results are presented for a cylindrical research combustor designed for operation with inlet-air state conditions typical for a 30:1 compression ratio, high bypass ratio, turbofan commercial engine.

Clayton, R. M.↗
NASA NTRS1980

Reduction of nitric oxide emissions from a combustor

A turbojet combustor and method for controlling nitric oxide emissions by employing successive combustion zones is described. After combustion of an initial portion of the fuel in a primary combustion zone, the combustion products of the primary zone are combined with the remaining portion of fuel and additional plenum air and burned in a secondary combustion zone under conditions that result in low nitric oxide emissions. Low nitric oxide emissions are achieved by a novel turbojet combustor arrangement which provides flame stability by allowing stable combustion to be accompanied by low nitric oxide emissions resulting from controlled fuel-lean combustion (ignited by the emission products from the primary zone) in a secondary combustion zone at a lower combustion temperature resulting in low emission of nitric oxide.

Craig, R. A.↗
NASA NTRS1980

Flow measurements in a model swirl combustor

Flow measurements in a model combustor composed of two confined coaxial swirling jets under noncombusting conditions are presented. Mean flow results are obtained for five different flow conditions to determine the effect of outer swirl on the recirculation zone (which is used for flame stabilization under combustion conditions). As the outer swirl magnitude is first decreased from maximum counter-swirl to zero and then increased to give co-swirl conditions, the size and the reverse flow velocity in the recirculation zone diminish. Detailed time mean and fluctuating flow measurements are obtained for a co-swirl and a counter-swirl condition with a directional pitot probe and hot-wire anenometry. For these two cases, recirculation zone occurs only with counter-swirl, near the exit of the inner jet. The recirculation zone is in the form of a one celled toroidal vortex having very low swirl velocity. Axial development of fluctuation levels, energy dissipation rates and turbulence length scales are described for the two flow conditions. Spectral analysis reveals periodic oscillations in both flows. The oscillations originate from the inner jet and up to 4 harmonics are observed. The fundamental frequencies are comparable to the rotational frequencies of the inner jets at the exit which are approximately under solid body rotation. The significance of the present results for the combustion process is discussed.

Vu, B. T.↗
NASA NTRS1980

Experiments on multiple vortices in a side dump gas generator ramjet

The role of multiple vortices in the flame stabilization process of a 4 inlet side dump ramjet was determined. Very rich propane air mixtures were injected at the head to simulate a gas generator ramjet. Swirl was introduced by canting the inlets at the dump station. The inlet angle, swirl angle, and the distance of the head from the dump station were varied over a wide range to determine the importance of the vortices located at the dump stations and at the head. It is shown that with proper design, the vortex at the head can be made to perform as a pilot burner allowing a great deal of versatility of operation and it appears to provide all the criteria of pollution free operation.

Choudhury, P. R.↗
NASA NTRS1981

Premixed turbulent flame blowoff velocity correlation based on coherent structures in turbulent flows

A correlation for the blowoff velocity of premixed turbulent flames stabilized by bluff bodies is devloped using a simple model for coherent structures in turbulent flows. The correlation shows the correct trends for variations in equivalence ratio, free stream pressure and temperature, flameholder characteristic size, and turbulent Reynolds number, and good agreement with published experimental data is obtained.

Radhakrishnan, K.↗
NASA NTRS1981

Symposium /International/ on Combustion, 18th, University of Waterloo, Waterloo, Ontario, Canada, August 17-22, 1980, Proceedings

Problems related to combustion generated pollution are explored, taking into account the mechanism of NO formation from nitrogen compounds in hydrogen flames studied by laser fluorescence, the structure and similarity of nitric oxide production in turbulent diffusion flames, the effect of steam addition on NO formation, and the formation of NO2 by laminar flames. Other topics considered are concerned with propellant combustion, fluidized bed combustion, the combustion of droplets and sprays, premixed flame studies, fire studies, and flame stabilization. Attention is also given to coal flammability, chemical kinetics, turbulent combustion, soot, coal combustion, the modeling of combustion processes, combustion diagnostics, detonations and explosions, ignition, internal combustion engines, combustion studies, and furnaces.

Source record↗
NASA NTRS1982

Bluff-body flameholder wakes - A simple numerical solution

Numerical finite difference predictions are made of recirculation zones behind bluff-body flame stabilizers, showing quantitatively the effects of forebody geometry, blockage ratio, lateral position of the blockage and inlet swirl on the central recirculation zone. A simple transient Navier-Stokes solution algorithm and laminar flow simulation are used with 'free slip' and 'no slip' wall boundary conditions, thus illustrating how a basic approach may be used to solve a sophisticated fluid dynamic problem.

Vatistas, G. H.↗
NASA NTRS1983

Small Gas Turbine Combustor Primary Zone Study

The combustion research program, small gas turbine combustor primary zone study is summarized. The basic elements of a design methodology program to obtain the maximum performance potential of small reverse-flow annular combustors is described. Three preferred combustion design approaches for internal flame stabilization patterns were selected. Design features are incorporated in the combustors to address the performance limiting problem areas associated with smaller annular combustors. Performance is predicted by using a 3-D aerodynamic/chemical kinetic elliptic flow analysis, initially developed by Garrett Corporation for the USARTL. It is shown that the analytical flow field predictive models provide a useful design tool for understanding the combustion performance of a small reverse flow annular combustor.

Sullivan, R. E.↗