Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - PLATES, FLAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

The effect of plasma heating on sublimation-driven flow in Io's atmosphere

The atmospheric flow on Io is numerically computed in a flat 2-D axisymmetric geometry for a sublimation atmosphere on the trailing hemisphere subjected to plasma bombardment, UV heating, and IR cooling. Calculations are performed for subsolar vapor pressures of approximately 6.5 x 10(exp -3) Pa (approximately 3 x 10(exp 18) SO2/sq cm) and 6.8 x 10(exp -4) Pa (approximately 4 x 10(exp 17) SO2/sq cm); the latter approximates the vapor pressure of F. P. Fanale et al. (1982). The amount of plasma energy deposited in the atmosphere is 20% of the plasma flow energy due to corotation (J. A. Linker et al., 1988). It is found that plasma heating significantly inflates the upper atmosphere, increasing both the exobase altitude and the amount of surface covered by more than an exospheric column of gas. This in turn controls the supply of the Io plasma torus (M. A. McGrath and R. E. Johnson, 1987). The horizontal flow of mass and energy is also important in determining the exobase altitude; and it is shown that IR cooling can be important, although our use of the equilibrium, cool-to-space approximation for a pure SO2 gas (E. Lellouch et al., 1992) may overestimate this effect. The calculated exobase altitudes are somewhat lower than those suggested by McGrath and Johnson (1987) for supplying the torus, indicating the details of the plasma energy deposition and sputter ejection rate near the exobase, as well as the IR emission from this region need to be examined. In addition, the molecules sublimed (or sputtered) from the surface are transported to the exobase in times short compared to the molecular photodissociation time. Therefore, the exobase is dominated by molecular species and the exobase is supplied by a small region of the surface.

Wong, Mau C.↗

A study of the structural-acoustic response and interior noise levels of fuselage structures

Models of both flat and curved fuselage panels were tested for their sound transmission characteristics. The effect of external air flow on transmission loss was simulated in a subsonic wind-tunnel. By numerically evaluating the known equations for field-incidence transmission loss of single-walled panels in a computer program, a comparison of the theory with the test results was made. As a further extension to aircraft fuselage simulation, equations for the field-incidence transmission loss of a double-walled panel were derived. Flow is shown to provide a small increase in transmission loss for a flat panel. Curvature is shown to increase transmission loss for low frequencies, while also providing a sharp decrease in transmission loss at the ring frequency of the cylindrical panel. The field-incidence transmission loss of a double-walled panel was found to be approximately twice that for a single-walled panel, with the addition of dips in the transmission loss at the air gap resonances and at the critical frequency of the internal panel.

Koval, L. R.↗

An experimental investigation of a three dimensional wall jet

One and two point statistical properties are measured in the flow fields of a coflowing turbulent jet. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of the circular nozzle; and the resultant effects on the flow field are determined. The one point quantities measured include mean velocities, turbulent intensities, velocity and concentration autocorrelations and power spectral densities, and intermittencies. From the autocorrelation curves, the Taylor microscale and the integral length scale are calculated. Two point quantities measured include velocity and concentration space-time correlations and pressure velocity correlations. From the velocity space-time correlations, iso-correlation contours are constructed along with the lines of maximum maximorum. These lines allow a picture of the flow pattern to be determined. The pressures monitored in the pressure velocity correlations are measured both in the flow field and at the surface of the confining wall(s).

Catalano, G. D.↗

Flow-establishment times for blunt bodies in an expansion tube

Flow establishment results are presented as obtained from shock standoff distance, pressure, and heat transfer measurements in the Langley expansion tube. The models tested were flat-faced cylinders with varying radius and a sphere with a constant radius, and they were positioned at the acceleration section exit and tested in the open jet at zero angle of attack. The experimental results were obtained as spinoff from various studies using helium, air, and CO2 test gases at freestream velocities in the range 5-7 km/sec. Time histories of shock detachment distance illustrate that the shock formation about the smaller-radii flat-faced cylinders and the sphere is symmetrical, whereas a complex, asymmetric formation is observed for the larger-radii cylinders. Flow is shown to establish more readily about the sphere than a flat-faced cylinder of the same diameter. A quasi-steady flow exists about relatively large blunt models during two-thirds of the approximate 250-microsec expansion tube test period.

Miller, C. G.↗

Radiative acceleration in outflows from broad absorption line quasi-stellar objects. 2: Wind models

We investigate the dynamics of radiatively driven broad absorption-line (BAL) outflows in quasi-stellar objects (QSOs) by developing radial and time-independent numerical models. Two limits are explored. The first assumes that the absorbing matter is not forced to comove with the substrate, which provides pressure confinement. This assumption allows us to explore in detail a case in which the acceleration is entirely due to radiation pressure. Using the parameters inferred from observations, we find that under these conditions radiative acceleration (mainly due to resonance line scattering) can readily accelerate the flow to the observed velocities. An important feature of the noncoupled flow is that the line profiles tend to stay relatively flat throughout the velocity interval covered by the line. We discuss how relaxing the assumptions of radial symmetry and time independent may help to explain the structures observed in BALs. In the second class of models, the absorbing flow is assumed to be completely coupled to the substrate in which it is embedded. Aside from being more plausible physically, these models produce line profiles that trail off at higher velocities, a behavior observed in some BALs. We show that, even if the substrate is massless, we have to assume a starting radius very close to the inferred radius of the broad emission-line region (approximately 0.1 pc) in order to obtain a significant contribution from radiative acceleration, given a typical active galactic nucleus (AGN) spectrum. The reason is that the energy input needed to pressurize the substrate, allowing the flow to become supersonic and to retain a reasonable ionization equilibrium, at the same time contributes appreciably to the acceleration. A way to relax the small starting radius constraint is to use a softer ionizing spectrum.

Arav, Nahum↗

The growth of aspherical structure in the universe - Is the Local Supercluster an unusual system

The growth and subsequent collapse of homogeneous ellipsoidal perturbations in a uniform expanding background is considered as a simple model for the formation of large-scale aspherical structures in the observed universe. Numerical calculations of the evolution of such perturbations turn out to be well described by an approximate analytic solution of the equations of motion, and simple relationships are found between the initial shape of a perturbation and its shape and kinematic properties at the time of collapse. Perturbations do not change their shape significantly until they reach a density contrast of order unity. As a result, structures with the kinematic properties of the Local Supercluster should form much more commonly in a low-density universe than in a flat universe. The homogeneity of the local Hubble flow, the motion of the Milky Way with respect to the microwave background, and the flattening of the Local Supercluster can be successfully accounted for by these models, provided that the initial perturbation is sufficiently flattened. Viable models are obtained only if the ratio of the lengths of the two smaller axes of the initial perturbation is at least 3:1 in an Einstein-de Sitter universe or at least 1.8:1 in a universe for which the density parameter (Omega) is of order 0.1, when the protocluster pancakes.

White, S. D. M.↗

High-Capacity Heat-Pipe Evaporator

Heat pipe with cylindrical heat-input surface has higher contact thermal conductance than one with usual flat surface. Cylindrical heat absorber promotes nearly uniform flow of heat into pipe at all places around periphery of pipe, helps eliminate hotspots on heat source. Lugs in aluminum pipe carry heat from outer surface to liquid oozing from capillaries of wick. Liquid absorbs heat, evaporates, and passes out of evaporator through interlug passages.

Oren, J. A.↗

Computational aspects of chemically reacting flows

An implicit, time-dependent approach is taken to solve the inviscid conservative equations in a vertex-based finite-volume formulation. The convective fluxes are estimated by a modified Riemann solver, and higher-order accuracy is obtained by means of the MUSCL. Implicit techniques are adopted to deal with the equation stiffness as a result of the clustered grid and chemical source term. The real-gas Roe matrix and the ADI and LU schemes have been tested on the sample problems: hypersonic flow over blunt configurations, such as the forebody of a double ellipse, and the near wake of a conic aerobrake. Temperature distribution and standoff distance are validated against the shock-fitting, central-differencing results. Equilibrium temperature may be recovered by artificially increasing the chemical rates at the wall. The present method satisfactorily resolves the flow structure, including the strong expansion behind the flat base. The relative merits and performance of the real-gas TVD and implicit schemes are discussed briefly.

Li, C. P.↗

Static and Dynamic Pressure Distributions in a Short Labyrinth Seal

As part of a study into turbine blade tip destabilizing forces, a seals test rig was built in which spin rate, circular whirl rate, direction and amplitude of inlet swirl angle, and eccentricity can all be controlled over wide ranges, and measurements can be made at gap Reynolds numbers up to about 2 x 10(exp 4). This facility is described and preliminary data is presented for a one cavity labyrinth seal with a flat, stator mounted land. The impact of different flow coefficients for the first and second knives on the rotordynamic coefficients was found. While this effect is dominant for the direct forces, it should also be incorporated into calculations of cross forces where it has an impact under many conditions.

Millsaps, K. T.↗

Direct numerical simulation of curved turbulent channel flow

Low Reynolds number, mildly curved, turbulent channel flow has been simulated numerically without subgrid scale models. A new spectral numerical method developed for this problem was used, and the computations were performed with 2 million degrees of freedom. A variety of statistical and structural information has been extracted from the computed flow fields. These include mean velocity, turbulence stresses, velocity skewness, and flatness factors, space time correlations and spectra, all the terms in the Reynolds stress balance equations, and contour and vector plots of instantaneous velocity fields. The effects of curvature on this flow were determined by comparing the concave and convex sides of the channel. The observed effects are consistent with experimental observations for mild curvature. The most significant difference in the turbulence statistics between the concave and convex sides was in the Reynolds shear stress. This was accompanied by significant differences in the terms of the Reynolds shear stress balance equations. In addition, it was found that stationary Taylor-Gortler vortices were present and that they had a significant effect on the flow by contributing to the mean Reynolds shear stress, and by affecting the underlying turbulence.

Moser, R. D.↗

Performance of the Bowen ratio systems on a 22 deg slope

The Bowen ratio energy balance technique was used to assess the energy fluxes on inclined surfaces during the First ISLSCP Field Experiment (FIFE). Since air flow over sloping surface may differ from that over flat terrain, it is important to examine whether Bowen ratio measurements taken on sloping surfaces are valid. In this study, the suitability of using the Bowen ratio technique on sloping surfaces was tested by examining the assumptions that the technique requires for valid measurements. This was accomplished by studying the variation of Bowen ratio measurements along a selected slope at the FIFE site. In September 1988, four Bowen ratio systems were set up in a line along the 22 degree north-facing slope with northerly air flow (wind went up the slope). In July of 1989, six Bowen ratio systems were similarly installed with southerly air flow (the wind went down slope). Results indicated that, at distances between 10 to 40 meters from the top of the slope, no temperature or vapor pressure gradient parallel to the slope was detected. Uniform Bowen ratio values were obtained on the slope, and thus the sensible or latent heat flux should be similar along the slope. This indicates that the assumptions for valid flux measurements are reasonably met at the slope. The Bowen ratio technique should give the best estimates of the energy fluxes on slopes similar to that in this study.

Nie, D.↗

Escalator design features evaluation

Escalators are available with design features such as dual speed (90 and 120 fpm), mat operation and flat steps. These design features were evaluated based on the impact of each on capital and operating costs, traffic flow, and safety. A human factors engineering model was developed to analyze the need for flat steps at various speeds. Mat operation of escalators was found to be cost effective in terms of energy savings. Dual speed operation of escalators with the higher speed used during peak hours allows for efficient operation. A minimum number of flat steps required as a function of escalator speed was developed to ensure safety for the elderly.

Zimmerman, W. F.↗

Pressure and force data for a flat wing and a warped conical wing having a shockless recompression at Mach 1.62

A conical nonlinear flow computer code was used to design a warped (cambered) wing which would produce a supercritical expansion and shockless recompression of the crossflow at a lift coefficient of 0.457, an angle of attack of 10 deg, and a Mach number of 1.62. This cambered wing and a flat wing the same thickness distribution were tested over a range of Mach numbers from 1.6 to 2.0. For both models the forward 60 percent is purely conical geometry. Results obtained with the cambered wing demonstrated the design features of a supercritical expansion and a shockless recompression, whereas results obtained with the flat wing indicated the presence of crossflow shocks. Tables of experimental pressure, force, and moment data are included, as well as selected oil flow photographs.

Miller, D. S.↗

Analysis of Probe Surveys Conducted in the 10-MW TP3 Arc-Jet Facility 15-Inch Nozzle Flow

Computational simulations and analysis of flow characterization tests in a high enthalpy arc-jet facility at NASA Ames Research Center are reported. These tests were conducted in the 10-MW TP3 facility 15-inch conical nozzle, and pitot pressure and heat flux probes are used to survey test flow downstream of the nozzle exit. Two 1.59-cm (0.625 in) diameter hemisphere probes were used: one with a stagnation-point pressure port, the other with a Gardon heat flux gage. Calibration data were also obtained using 20.32-cm flat-faced slug calorimeters. Experimental surveys of arc-jet test flow with pitot pressure and heat flux probes were obtained at eight arc-heater conditions, covering wide ranges in arc current (316–1756 A) and mass flow rate (32–500 g/s, without any cold-gas injection at the arc-heater plenum) and providing assessment of the flow uniformity in the facility. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested. These simulations take into account non-uniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields. Comparisons of computations with the experimental measurements are presented, showing reasonably good agreement. The probe survey data and accompanying analysis show that the test flow in the TP3 15-inch nozzle is highly non-uniform at most conditions, and the extent of flow non-uniformity depends on arc current and mass flow rate.

Arc-jets↗

Natural convection in steady solidification - Finite element analysis of a two-phase Rayleigh-Benard problem

Galerkin finite-element approximations and Newton's method for solving free boundary problems are combined with computer-implemented techniques from nonlinear perturbation analysis to study solidification problems with natural convection in the melt. The Newton method gives rapid convergence to steady state velocity, temperature and pressure fields and melt-solid interface shapes, and forms the basis for algebraic methods for detecting multiple steady flows and assessing their stability. The power of this combination is demonstrated for a two-phase Rayleigh-Benard problem composed of melt and solid in a veritical cylinder with the thermal boundary conditions arranged so that a static melt with a flat melt-solid interface is always a solution. Multiple cellular flows bifurcating from the static state are detected and followed as Rayleigh number is varied. Changing the boundary conditions to approach those appropriate for the vertical Bridgman solidification system causes imperfections that eliminate the static state. The flow structure in the Bridgman system is related to those for the Rayleigh-Benard system by a continuous evolution of the boundary conditions.

Chang, C. J.↗

Discrete wall jets in quiescent air

An experimental investigation was made of turbulent jet flows resulting from small, round nozzles discharging parallel to a smooth, flat wall in quiescent air. Nozzle axes were located 3.0 nozzle diameters above the wall surface. The case of a single nozzle and the case of a spanwise array of equally spaced nozzles were investigated. Several forms of approximate velocity profile similarity were noted, and the flow from the array of nozzles was seen to approach the form of a two-dimensional wall jet.

Mclean, J. D.↗

Structure of radio sources with remarkably flat spectra - PKS 0735+178

Three incoherent synchrotron models are used to account for the very flat radio spectrum of the BL Lac object PKS 0735+178. The first interpretation is that the spectrum results from optically-thin synchrotron emission from relativistic electrons with a particular energy distribution. The second posits a single nonuniform, self-absorbed source generated by a wind flowing from a central object. The third suggests that sources with flat spectra are caused by the presence of multiple (three or more) discrete uniform components, and that the magnetic field and relativistic electron distribution for each source is correlated with the size of the individual components. It is proposed that the last model is the most tenable explanation of the phenomenon, and multi-frequency VLBI observations are suggested for the evaluation of the detailed structure of compact radio sources.

Marscher, A. P.↗