Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLY ASH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Influence of supplementary cementitious materials on microstructure and transport properties of spacer-concrete interface

Reinforcement spacers are a critical component of concrete structures. Their presence affects microstructure and transport properties of concrete cover though this is not widely appreciated. This paper presents the first study to determine whether the negative effects of spacers can be mitigated through the use of supplementary cementitious materials such as silica fume, fly ash and blast-furnace slag. Concrete samples (>200) with different spacers, binders, curing and drying regimes were prepared and tested for diffusion, permeation, absorption, electrical conductivity, carbonation and microstructure. It was found that spacers increase all transport properties, the extent depending on type of spacer, drying regime and transport mechanism. The spacer-concrete interface is weak, porous and micro-cracked, and this lowers the resistance of concrete to ingress of aggressive agents. The beneficial effects of SCMs (strength enhancement and densification) and prolonged curing (120-day) are insufficient to overcome the negative effects of spacers. Implications for durability are discussed.

36 MATERIALS SCIENCE↗

Formulation of low clinker blended cements and concrete with enhanced fresh and hardened properties

Blended cements appear as the most promising way to massively produce cements with reduced environmental footprints. However, considering the generally lower early mechanical performance of highly blended cements, chemical admixtures are increasingly relied upon to increase early strength. However, in many cases this can negatively impact other properties as rheology and durability. This paper proposes an approach to formulate low clinker cements and concrete using moderate alkali activation or gypsum to enhance early and long-term compressive strength, without inducing excessive alkali-silica reaction (ASR) expansion. It examines blended cements containing burnt oil shale along with limestone and fly ash or slag as supplementary cementitious materials. It optimizes the combination of polycarboxylate ether (PCE) superplasticizers with the strength enhancers. Along with the use of Ca(NO{sub 3}){sub 2} to drive PCE adsorption, this provides good rheology control, increased early and long-term compressive strength, as well as acceptable ASR expansion in cements with only 50% clinker.

36 MATERIALS SCIENCE↗

Distributed sustainable metals production: opportunities for intensifying separations & alternative feedstocks

Meeting the increased demand for rare earth elements and beyond primary mined ore. Secondary sources like phosphogypsum, coal fly ash, used nuclear fuel, and electronic waste are concentrated sources of critical minerals. One strategy for a resilient supply chain is to decentralize sourcing and hydrometallurgical processing of metals. Rotating packed beds (RPBs) for solid-phase extraction and liquid-liquid extraction are gaining momentum for their ability to increase process throughput by 5-10x the state of the art. In conclusion, this review discusses advances in hydrometallurgical RPB processes and opportunities for implementation in distributed metals production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of paste microstructure for durability properties of concrete

In this study, paste samples from different cementitious systems were characterized by using X-Ray Micro Computed Tomography (µ-CT) and Fluorescence Microscopy techniques. Quantitative and qualitative aspects of defects from paste samples were investigated to develop indicators of durability related properties of corresponding concrete samples. In the first phase of this study, hour glass shaped 3D printed molds were used to investigate five cementitious combinations consisting of three cement types (Coarse Ground portland cement, Type IL Portland Limestone Cement and Type I/II ordinary portland cement) and fly ash as a supplementary cementitious material. In the second phase, metal molds were used to compare the results of Coarse Ground portland cement with Type I ordinary portland cement, 5% of which was replaced with colloidal nanosilica. Potential correlations between paste and concrete have been presented. This work was supported by US Department of Energy and North Dakota Department of Commerce.

36 MATERIALS SCIENCE↗

Sulfuric Acid Improves the Reactivity of Zeolites via Dealumination

The demand for supplementary cementitious materials (SCMs), like fly ash, slag, and silica fume, is projected to rise over the next few decades. However, global decarbonization efforts, such as decommissioning of coal-fired power plants, will limit the supply of SCMs. Therefore, alternative SCM sources are a critical need for the cement and concrete industry. However, the high crystallinity of zeolites limits their pozzolanic reactivity. The goal of this work was to improve the reactivity of two common zeolites, namely clinoptilolite and SSZ-13, by treating them with sulfuric acid. The treatment enhanced zeolite reactivity via dealumination and decreased particle sizes, which led to increased reactivity with calcium hydroxide, as indicated by a 42.0% increase in reaction heat measured by isothermal calorimetry. Here, we elucidate mechanistic understanding that smaller particle sizes induced by acid treatment accelerated peak heat evolution, while free aluminates from dealumination increased heat via direct reaction with aqueous Ca 2+ .

36 MATERIALS SCIENCE↗

Pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites

Here, this paper studies the pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites. A hybrid approach was proposed by combining the advantages of traditional chemical-induced foaming (foaming approach) and lightweight particulate inclusions (synthetic foam approach). A comprehensive experimental program was conducted to evaluate the effects of foaming agents and fly ash cenosphere (FAC) on the printability, microstructure, mechanical and thermal properties of 3D printed samples. The results showed that the hybrid approach could produce a mixture with a density as low as 470 kg/m 3 while ensuring good flowability and buildability owing to the lubricating effect of foaming and supporting skeleton formed by FAC. In addition, a three-step homogenization procedure was also developed to predict the effective elastic modulus and thermal conductivity of 3D printable cementitious composites and cementitious foam. The findings of the study highlighted the effectiveness of the hybrid approach in formulating 3D printable ultra-lightweight cementitious composites in thermal insulation and acoustic applications.

36 MATERIALS SCIENCE↗

Enabling thermal energy storage in structural cementitious composites with a novel phase change material microcapsule featuring an inorganic shell and a bio-inspired silica coating

Phase change material (PCM) microcapsules offer a promising approach for integrating PCM into building materials for efficient thermal energy storage. Here, this study presents the development of a novel PCM microcapsule specifically designed for incorporation into cementitious materials. The microcapsule consists of a low-cost PCM core derived from vegetable oil by-products and a durable inorganic shell made from cenosphere, a hollow fly ash generated from coal burning power plants. A novel process is developed to apply a silica coating to these cenosphere-based PCM microcapsules (CPCM), resulting in bioinspired-silica-coated CPCM microcapsules (BCPCM). This coating process draws inspiration from marine microorganism-based silica production and utilizes low-cost sodium silicate as a precursor, enabling eco-friendly and cost-effective manufacturing at ambient temperature and mild pH conditions. The morphology, chemical stability, and thermal properties of the BCPCM along with its thermo-mechanical performance in cementitious composites were comprehensively analyzed. Experimental results demonstrate successful silica deposition on BCPCM, leading to enhanced latent heat properties of the produced BCPCM. With the silica coating, BCPCM exhibits a 50 °C delay in thermal decomposition compared to CPCM, enhancing fire resistance and preventing premature PCM leakage of the microcapsule. The bioinspired silica coating effectively restores over 10% of the strength loss for each percent increase in CPCM incorporated into the mortar. The thermal performance experiments reveal that increasing the BCPCM content reduces temperature peaks and rates of temperature increase, indicating an improved capacity for thermal energy storage. This new PCM microcapsule provides a cost-effective solution to integrate thermal energy storage to cementitious material, as evidenced that over 30% of aggregates (in volume) can be replaced by the microcapsule without a drastic loss of strength.

25 ENERGY STORAGE↗

Thermal shock resistance of lightweight cements developed for geothermal conditions

Cements are a critical component in well construction, as they act to prevent well fluid and gas escape, prevent corrosion of the casing, and strengthen the wellbore to prevent deformation. Under the high temperature/pressure conditions common in geothermal systems, the injection of cold water for energy production is expected to induce cyclic damage to the borehole cement through the rapid temperature fluctuations. These “thermal shocks” are expected to cause casing shrinkage, annulus formation, and cement tensile stresses. To understand the effect of cold water injection on the wellbore environment, a set of rock-cement-steel samples were created to simulate the structure of a geothermal well. Lightweight thermally-insulating cement blends were tested under thermal shock conditions in this study. In each test, the samples were pressurized to an effective pressure of ~3.5 MPa and placed at high temperatures. Thermal shocks were performed by injecting cold water (~10-15 °C) through the samples at a constant rate while keeping the samples at high temperatures until the sample temperature stopped decreasing and deformation ceased. Eight thermal shock tests were conducted with each sample – two at 100 °C and six at 200 °C. Post-tests analysis was then conducted by cutting open each sample to examine the damage in each component of the simulated wellbore. Experimental results suggest that all samples experienced similar degrees of axial and lateral contraction during cold water injection, but for the most part this contraction is recoverable when injection halts. Post-test analysis revealed that fly ash cenosphere pre-treatment had the best effect on improving thermal shock resistance in the cement blends. Thermomechanical modeling of likely stress paths experienced by the cements during heating/cooling cycles shows that elasto-plastic cement constitutive behavior results in most plastic strain occurring during the initial heating steps, with mostly elastic strain occurring during the thermal shock cycles. In conclusion, this agrees with experimental evidence, suggesting that cement damage from shocking occurs via other mechanisms such as chemical alteration, corrosion, and fatigue.

36 MATERIALS SCIENCE↗

Role of carbon treating in piperazine oxidation

Bench-scale experiments were performed to test the effects of carbon treating (8 × 30 mesh, lignite-based granular activated carbon from Nowata Filtration) on the oxidation of aqueous piperazine (PZ) at conditions of CO 2 capture. The combined mitigation with carbon treating and N 2 sparging was also tested. When carbon treating is applied, the UV–Vis absorbance at 320 nm, the NH 3 production rate, and the accumulation rate of dissolved Fe concentration and total formate concentration decrease. The effects of carbon treating last even when the carbon is bypassed, which is possibly due to the removal of catalytic degradation products. Therefore, it is better to apply carbon treating in the early stages of oxidation. Combining carbon treating and nitrogen sparging is more effective in oxidation mitigation than applying the methods separately. The amount of Fe removed by the carbon bed is greater than the result calculated from the solvent inventory and concentration difference of Fe in solvent, indicating that Fe colloids or other “soluble” Fe will dissolve into the solvent and replace the dissolved Fe that is adsorbed and removed. Furthermore, the carbon removes the degradation products that can complex with Fe 3+ , even if they are not complexed. Since the source of Fe includes fly ash and corrosion, removing the complexing agents instead of all the available Fe is a more feasible target.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Adsorption of rare earth elements in carboxylated mesoporous carbon

The separation of Rare Earth Elements (REEs) from various non-conventional sources is critically important to maintain the supply–demand balance of REEs in the western world. Here, in this research, we have investigated coal Fly Ash (CFA) as the non-conventional source of REEs. In order to recover REEs, we have synthesized carboxylate-functionalized mesoporous carbon (CMC) to harness the chelation-induced adsorption of REEs. These adsorbents were characterized with pore textural properties, FTIR spectroscopy, and SEM-EDX mapping. In the initial study with single-component La(III) Dy(III) and Lu(III), it was revealed that CMC can adsorb those REEs 2–4 times more than that of pristine mesoporous carbon confirming the effective role of the carboxylate group in the REE separation. Furthermore, the affiliation of the carboxylate group towards heavier REEs (Lu>Dy>La, when present is equal amounts) provides an added benefit of this adsorbent owing to the high demand for heavier REEs in the technology sectors. The leachate solution produced from CFA contained sixteen REEs in the range of 50–200 ppb for most of the REEs. It was revealed that CMC can extract 80–90% of all the REEs thereby further confirming the success of the CMC as an effective REE sorbent. Three successive cycles of adsorption and desorption of REEs with the same CMC revealed the consistent adsorption capacity of REEs. In-situ X-ray Absorption Near Edge Spectroscopy (XANES) analysis confirmed the +3 oxidation states of La, Dy, and Lu within CMC. In-situ Extended X-ray Absorption Fine Structure (EXAFS) analysis revealed the shortening of mean La-O, Dy-O, and Lu-O bond distance by 0.03–0.05 Å thereby confirming the coordination of these REEs with carboxylate groups present on CMC.

36 MATERIALS SCIENCE↗

Incorporation of Oxygen Carrier Recycle into Large-Scale Production of Cu-Based Oxygen Carriers

One of the greatest challenges in the chemical looping combustion (CLC) of solid fuels is developing an oxygen carrier material that is reactive and attrition resistant and can be prepared at a reasonable cost. Recent efforts in oxygen carrier development have followed two primary approaches: (1) using natural ores, such as ilmenite, or (2) developing highly attrition-resistant and reactive synthetic materials. Both approaches have shortcomings, namely, the low reactivity and incompatibility of ores with solid fuel CLC and the high cost and low durability of synthetic materials. Here, a different approach is taken where attrition is assumed inevitable and the recycling of spent oxygen carrier materials is incorporated into oxygen carrier manufacture. For solid fuel CLC, Cu-based oxygen carriers are attrited and are collected with fly ash. Copper oxides are more reactive with nitric acid than most ash materials, meaning that a copper-nitrate-rich leachate can be generated. This copper nitrate stream could then be reused in oxygen carrier synthesis by impregnation. For proof of concept, leaching experiments were conducted to verify that copper oxides are selectively leached from ash-containing spent oxygen carriers. Several cases for process design are proposed based on the composition of spent materials, as the degree of copper oxidation and type of solid fuel dictate leaching residence times and general processing intensity. The four stages proposed here include impurity removal, copper leaching and recovery, solid–liquid separation, and evaporation/concentrating. The resulting process should be able to recover up to 95% of copper while minimizing inclusion of undesirable ash-based impurities.

anions↗

Effects of Cement Changes and Aggregate System on Mechanical Properties of Concrete

In this paper, mechanical properties of concrete mixtures containing different cementitious combinations and two aggregate systems were investigated under plastic and drying conditions. Emphasis was laid on durability and shrinkage of concrete. Life Cycle Analysis was also conducted by using Green Concrete LCA Webtool. Results indicated that the presence of larger aggregate sizes tend to enhance durability of concrete. The presence of nanosilica also imparted superior mechanical properties to concrete. A cementitious combination containing Portland Limestone Cement and fly ash with larger aggregate sizes emerged as a better performing mixture in terms of mechanical properties and with minimum environmental impact.

36 MATERIALS SCIENCE↗

Electrochemistry of Praseodymium in Aqueous Solution Using a Liquid Gallium Cathode

We report the electrochemistry of liquid Ga electrodes in aqueous media was examined in the presence of praseodymium acetate (PrOAc) as an alternate path for low temperature reduction of rare earth elements (REE). This study investigated the aqueous electrochemistry of Ga with and without REEs (Pr). Cyclic voltammetry experiments showed that in the presence of PrOAc, an order of magnitude increase in cathodic current was observed for the Ga electrode, compared to that in the absence of Pr. Decrease in the reduction current with the increase of scan rate, with and without Pr, suggests catalytic reactions following electron transfer, which was attributed to the Ga 2 O disproportionation reaction. Chronoamperometric experiments performed in Pr containing solutions formed a precipitate. Over 50% of the Pr ions from the aqueous electrolyte were immobilized in the precipitate; a solid Ga-rich phase. Formation of this precipitate was only possible when Ga oxidation was induced. This condition was achieved by circulation of liquid Ga from the pool via external pump and returned dropwise to the liquid Ga pool. When the collected precipitate was leached in dilute HCl, Pr was released with H 2 evolved as a byproduct, and Ga returned to its initial liquid metallic state. These preliminary results show encouraging new routes that could be applied for the recovery of diluted REE leachates, such as those obtained from magnets, coal fly ash, and ores.

25 ENERGY STORAGE↗

Methane generation rates from Tank 50 simulant with methylmercury containing saltstone grout solids

This report documents the tests performed to address the requirements listed in the Technical Assistance Request, which resulted in a Test Plan to obtain the required information. To that end the results are documented herein to determine the capacity, and reaction time, for methylmercury (MeHg) contained within Tank 50 salt solution simulant (T50SS) to produce methane when mixed with saltstone dry feed ingredients, as individual components (cement, slag cement, and fly ash) or a combination of those components.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Comprehensive Study of the Potential of Extracting and Processing Critical Minerals from Coal-Based Resources - Phase I

The Phase I report prepared for the Department of Energy addresses U.S. Executive Order 13817 titled A Federal Strategy to Ensure Secure and Reliable Supplies of Critical Minerals, issued on December 20, 2017, that lists 35 critical minerals that are vulnerable to supply disruption. A comprehensive review of each of the minerals was conducted to determine the criticality based primarily on extractability from coal-based resources. Several other factors were also considered such as gaps in supply and demand, use in current technology, and the existence of viable substitutes. It was determined that the critical minerals that show highest potential for extraction from coal-based resources are lithium, rare earth elements (REEs), cobalt, and manganese. All four of the critical minerals listed serve an important role in the technology industry, have few substitutes, and have a heavy import reliance. Most notably are lithium, which is widely used in the electric vehicle industry, and the REEs which can be found in virtually all electronic devices. The research of critical mineral extraction from coal-based resources was completed using a combination of literature review from public sources as well as cooperation from coal mines and power plants across the United States. Samples collected from six different geographical locations across the U.S. were subjected to sample preparation (i.e., pH measurement, moisture content, particle size analysis) and characterization studies using Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) and Scanning Electron Microscopy, Energy Dispersive X-Ray Spectroscopy (SEM-EDX) instruments. 27 samples of coal waste materials such as refuse, sludge, and fly ash were tested to characterize the rare earth element concentration by total rare earth elements (TREEs), heavy rare earth elements (HREEs), and light rare earth elements (LREEs). Of the 27 samples tested, 22 contained a TREE concentration higher than the threshold of 300 ppm, which is considered a viable feedstock material. 3 samples contained less than 300 ppm of TREEs; however, they were within 20 ppm of the threshold, and could potentially be considered viable sources in the future pending the advancement of more efficient extraction technologies. 2 of the 27 samples had significantly low TREE concentrations, which does not imply any potential for being a source for REEs. For the minerals identified as most critical in the literature review, a conceptual process flow diagram (PFD) was developed for their extraction from different coal-based feedstocks. The process targets selective recovery of one commodity (i.e., rare earths, lithium, cobalt, and manganese) via several hydrometallurgical separation methods. By identifying potentially extractable coal-based critical mineral resources, a study of the current and future market environments for each critical mineral, and a review of current processing methodologies for critical mineral extraction from coal-based resources, the foundation has been laid to further characterize and explore new resources and extraction techniques. As reliance on technologies in industries such as the production of electronic devices, batteries, and alloys containing critical minerals utilizing critical minerals continues to increase, a sound understanding of our nation’s dependence on and even the global criticality of certain critical minerals, will serve as a catalyst for innovation in virtually all fields of science.

01 COAL, LIGNITE, AND PEAT↗

Review of Mercury Sequestration in Cementitious Waste Forms

Decontaminated salt solution from Tank 50 at the Savannah River Site (SRS) is known to contain dissolved mercury species which are present as hydroxides and oxides. These species are reported in analytical measurements as the organic cation [CH 3 Hg] + and the inorganic cation Hg 2+ . The salt solution is mixed with cementitious reagents, blast-furnace slag (BFS) and thermally beneficiated Class F fly ash in the Saltstone Processing Facility and pumped into engineered Saltstone Disposal Units, (SDUs), to produce a solidified waste form. The solidified waste form, saltstone, encapsulates and chemically stabilizes the mercury and other contaminants, sequestering them from release into the environment. With the discovery of methylmercury in the salt solution, testing was performed to determine the extent to which saltstone prepared with methylmercury (MeHg) retains mercury in the Toxicity Characteristic Leaching Procedure (TCLP). Results from this testing indicated that the amount of mercury extracted remained below the regulatory limit, and that the saltstone formulation with a greater proportion of BFS performed slightly better at retaining Hg in the solid.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimization of Conditions for Photoluminescence-Based Sensing of Critical Minerals: Strategies and Outlook

Economically critical minerals and metals are vital to America’s security, with application areas in energy, advanced technologies, and defense systems. The growing implementation of renewable energy sources such as electric vehicles is expected to significantly increase demand for these minerals, while the global supply is monopolistic, with most of the production occurring in a few countries outside of the US. To mitigate potential supply chain vulnerabilities, the domestic production of economically critical metals has become a bipartisan priority of the US government, and unconventional sources such as coal and its utilization byproducts such as fly ash and acid mine drainage are being actively explored as an alternative method for meeting domestic demand. Slow and expensive characterization methods for critical metals present a significant pain point for domestic production, which has led to the exploration of alternative low-cost, portable platforms capable of detecting target metals during resource prospecting and downstream process monitoring. The National Energy Technology Laboratory has developed a portable fiber optic-based luminescence spectrometer that utilizes a metal-organic framework (MOF) material to detect and distinguish parts-per-billion levels of the visible-emitting rare earth elements terbium, dysprosium, samarium, and europium, which are all economically critical metals. Although preliminary results with this system are promising, a crucial barrier to practical deployment is the ability to operate in low pH, high ionic strength environments, as acidic conditions and the presence of other metal ions can significantly reduce luminescence signal. Here, current strategies related to sample treatment, material design, and sensor configuration are discussed in the context of improving sensor performance in application-relevant conditions. Additionally, future opportunities, such as the optimization of the sensing binding environment through computational methods and specific metals to be removed for treatment will be discussed, presenting a forward-looking view for innovation in luminescent sensing of critical metals.

36 MATERIALS SCIENCE↗

April 2024 Semiannual Composite Salt Waste Processing Facility (SWPF) Decontaminated Salt Solution (DSS) Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from the Salt Waste Processing Facility (SWPF) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Saltstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00027, Revision 0, one SDF waste form (saltstone) sample was prepared in the Savannah River National Laboratory (SRNL) from the SWPF Decontaminated Salt Solution (DSS) Waste Acceptance Criteria (WAC) sample and Z-area premix material for the April 2024 semiannual Toxicity Characteristic Leaching Procedure (TCLP) sample. The sample contained 60:40 (by weight) of slag and fly ash (referred to as the “Cement-Free grout sample”). Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). After at least 28 days cured, a sample of the SDF waste form was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure (TCLP). The April 2024 semiannual Cement-Free grout sample met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and met the SPF WAC that was in effect at the time of the tank sampling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗