Search NASA⌕ Search

SEARCH · Search NASA

Results for “FORCE DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

An Aerodynamic Assessment of Micro-Drag Generators (MDGs)

Commercial transports as well as fighter aircraft of the future are being designed with very low drag (friction and pressure). Concurrently, commuter airports are being built or envisioned to be built in the centers of metropolitan areas where shorter runways and/or reduced noise footprints on takeoff and landing are required. These requirements and the fact that drag is lower on new vehicles than on older aircraft have resulted in vehicles that require a large amount of braking force (from landing-gear brakes, spoilers, high-lift flaps, thrust reversers, etc.). Micro-drag generators (MDGs) were envisioned to create a uniformly distributed drag force along a vehicle by forcing the flow to separate on the aft-facing surface of a series of deployable devices, thus, generating drag. The devices are intended to work at any speed and for any type of vehicle (aircraft, ground vehicles, sea-faring vehicles). MDGs were applied to a general aviation wing and a representative fuselage shape and tested in two subsonic wind tunnels. The results showed increases in drag of 2 to 6 times that of a "clean" configuration.

Bauer, Steven X. S.↗
NASA NTRS1956

A method for calculation of free-space sound pressures near a propeller in flight including considerations of the chordwise blade loading

This report presents tabulated values of certain definite integral that are involved in the calculation of near-field propeller noise when the chordwise forces are assumed to be either uniform or of a Dirac delta type. The tabulations are over a wide range of operating conditions and are useful for estimating propeller noise when either the concept of an effective radius or radial distributions of forces are considered. Use of the tabulations is illustrated by several examples of calculated results for some specific propellers.

NOISE↗
NASA NTRS1996

Numerical Comparison of Active Acoustic and Structural Noise Control in a Stiffened Double Wall Cylinder

The active acoustic and structural noise control characteristics of a double wall cylinder with and without ring stiffeners were numerically evaluated. An exterior monopole was assumed to acoustically excite the outside of the double wall cylinder at an acoustic cavity resonance frequency. Structural modal vibration properties of the inner and outer shells were analyzed by post-processing the results from a finite element analysis. A boundary element approach was used to calculate the acoustic cavity response and the coupled structural-acoustic interaction. In the frequency region of interest, below 500 Hz, all structural resonant modes were found to be acoustically slow and the nonresonant modal response to be dominant. Active sound transmission control was achieved by control forces applied to the inner or outer shell, or acoustic control monopoles placed just outside the inner or outer shell. A least mean square technique was used to minimize the interior sound pressures at the nodes of a data recovery mesh. Results showed that single acoustic control monopoles placed just outside the inner or outer shells resulted in better sound transmission control than six distributed point forces applied to either one of the shells. Adding stiffeners to the double wall structure constrained the modal vibrations of the shells, making the double wall stiffer with associated higher modal frequencies. Active noise control obtained for the stiffened double wall configurations was less than for the unstiffened cylinder. In all cases, the acoustic control monopoles controlled the sound transmission into the interior better than the structural control forces.

Grosveld, Ferdinand W.↗
NASA NTRS1973

Stress wave calculations in composite plates using the fast Fourier transform.

The protection of composite turbine fan blades against impact forces has prompted the study of dynamic stresses in composites due to transient loads. The mathematical model treats the laminated plate as an equivalent anisotropic material. The use of Mindlin's approximate theory of crystal plates results in five two-dimensional stress waves. Three of the waves are flexural and two involve in-plane extensional strains. The initial value problem due to a transient distributed transverse force on the plate is solved using Laplace and Fourier transforms. A fast computer program for inverting the two-dimensional Fourier transform is used. Stress contours for various stresses and times after application of load are obtained for a graphite fiber-epoxy matrix composite plate. Results indicate that the points of maximum stress travel along the fiber directions.

Moon, F. C.↗
NASA NTRS2008

Miniature Latching Valve

A miniature latching valve has been invented to satisfy a need for an electrically controllable on/off pneumatic valve that is lightweight and compact and remains in the most recently commanded open or closed state when power is not supplied. The valve includes a poppet that is moved into or out of contact with a seat to effect closure or opening, respectively, of the flow path. Motion of the poppet is initiated by electrical heating of one of two opposing pairs of nickel/titanium shape-memory alloy (SMA) wires above their transition temperature: heated wires contract to their remembered length, applying tension to pull the poppet toward or away from the seat. A latch consisting mainly of a bistable Belleville washer (a conical spring) made of a hardened stainless steel operates between two stable positions corresponding to the fully closed or fully open state, holding the poppet in one of these positions when power is not applied to either pair of SMA wires. To obtain maximum actuation force and displacement, the SMA wires must be kept in tension. The mounting fixtures at the ends of the wires must support large tensile stresses without creating stress concentrations that would limit the fatigue lives of the wires. An earlier design provided for each wire to be crimped in a conical opening with a conical steel ferrule that was swaged into the opening to produce a large, uniformly distributed holding force. In a subsequent design, the conical ferrule was replaced with a larger crimped cylindrical ferrule depicted in the figure. A major problem in designing the valve was to protect the SMA wires from a bake-out temperature of 300 C. The problem was solved by incorporating the SMA wires into an actuator module that is inserted into a barrel of the valve body and is held in place by miniature clip rings.

Johnson, A. David↗
NASA NTRS1954

Aerodynamic Characteristics of a Circular Cylinder at Mach Number of 6.86 and Angles of Attack up to 90 Degrees

Pressure-distribution and force tests of a circular cylinder have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.86, a Reynolds number of 129,000 based on diameter, and angles of attack up to 90 degrees. The results are compared with the hypersonic approximation of Grimminger, Williams, and Young and with a simple modification of the Newtonian flow theory. The comparison of experimental results shows that either theory gives adequate general aerodynamic characteristics but that the modified Newtonian theory gives a more accurate prediction of the pressure distribution. The calculated crossflow drag coefficients plotted as a function of crossflow Mach number were found to be in reasonable agreement with similar results obtained from other investigations at lower supersonic Mach numbers. Comparison of the results of this investigation with data obtained at a lower Mach number indicates that the drag coefficient of a cylinder normal to the flow is relatively constant for Mach numbers above about 4.

Penland, Jim A↗
NASA NTRSDate not supplied

Comparison of Convective Heat Transfer Correlations and Their Application to Nuclear Thermal Propulsion Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Experiment↗
NASA NTRS1962

Combined Radiation and Forced Convection for Flow of a Transparent Gas in a Tube with Sinusoidal Axial Wall Heat Flux Distribution

An analysis is made of the influence that radiation exchanges between elements on the inside surface of a tube have on the wall and gas temperature distributions for forced-convection flow. The wall heat generation has a chopped sine distribution with length along the tube, which is a distribution often encountered in nuclear-reactor channels. The flowing gas is assumed transparent to thermal radiation and hence does not participate directly in the radiative exchange process. Axial heat conduction is neglected in the gas and tube wall, and the convective-heat-transfer coefficient and fluid properties are assumed constant. Several numerical examples are given to illustrate the effects of eight independent parameters such as wall emissivity, Stanton number, and length-diameter ratio. In some instances the radiation exchanges reduced the peak wall temperature or caused a reduction in the exit gas temperature because of radiation losses from the tube end openings.

TUBE↗