Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow fields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Three dimensional flow field inside the passage of a low speed axial flow compressor rotor

Measurements of the subsonic flow in the rotor passage of a single stage axial flow compressor were made to study the nature of the flow field and to verify the existing numerical codes. The velocity and pressure fields were measured across the entire rotor passage at six axial locations and at five radial locations. A five-hole probe, rotating with the rotor, was used to measure the three components of velocity, the static and the total pressure. The experimental results are compared with the predictions from Katsanis and McNally's computer program. The agreement between the two is good for most of the cases.

Pouagare, M.↗

Calculation of inlet flow fields by an implicit technique

Two-dimensional inlet flow fields in a supersonic free stream are calculated by an implicit, shock-capturing, finite-difference method. The Euler equations are subjected to a general curvilinear transformation and a body-fitted coordinate system is employed. The method is used to solve supercritical, critical, and subcritical flow fields which are simulated by prescribing appropriate conditions at the inlet outflow boundary. Results are presented for a drooped-cowl inlet.

Biringen, S.↗

Investigation of a delta-wing fighter model flow field at transonic speeds

The paper reports a flow-field investigation on a 7.52-percent scale model of an advanced fighter aircraft design conducted in the NASA-Langley 16-ft Transonic Tunnel. The effects of free-stream Mach number, angle-of-attack, angle of sideslip, and various vortex control devices on the local flow values were studied. The model was tested at Mach numbers of 0.6, 0.9, and 1.2 and the angles of sideslip of 0 and +/- 5 deg; the model angle-of-attack was varied from -4 to 30 deg. Results are presented in terms of contour plots of local total pressure recovery. The dominant influence on the over-wing flow field was found to be the wing leading-edge vortex which first appears in the survey region at an angle-of-attack of 8 deg and increases in strength and influence with increasing angle-of-attack, finally dominating the entire survey region at very high angles-of-attack.

Bare, E. Ann↗

Flow field and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An experimental study of the flow field and acoustic properties of a low Reynolds number M = 0.9 jet has been performed in a low pressure anechoic test chamber. The mean flow field was surveyed with a conventional pitot pressure probe and flow fluctuations were detected with a normal hot wire probe. Also, condenser microphone measurements were made in the acoustic field. The flow fluctuations within the jet were found to be dominated initially by a relatively discrete, large-scale, wave-like instability centered around a Strouhal number of 0.44. The axial wavelength of this instability was determined to be 1.45 jet diameters and its azimuthal character includes the n = 0 and n = plus or minus 1 modes. The growth of this instability coupled with its nonlinear breakdown are major contributors to the termination of the potential core region of the jet. The acoustic field of the jet, in contrast to the flow field, has a broad frequency spectrum with a peak amplitude near a Strouhal number of St = 0.2. The results indicate that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from this jet.

Stromberg, J. L.↗

Pitot pressure measurements in flow fields behind circular-arc nozzles with exhaust jets at subsonic free-stream Mach numbers

The flow field behind a circular arc nozzle with exhaust jet was studied at subsonic free stream Mach numbers. A conical probe was used to measure the pitot pressure in the jet and free stream regions. Pressure data were recorded for two nozzle configurations at nozzle pressure ratios of 2.0, 2.9, and 5.0. At each set of test conditions, the probe was traversed from the jet center line into the free stream region at seven data acquisition stations. The survey began at the nozzle exit and extended downstream at intervals. The pitot pressure data may be applied to the evaluation of computational flow field models, as illustrated by a comparison of the flow field data with results of inviscid jet plume theory.

Mason, M. L.↗

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. A comparison of the data taken at the two different operating conditions indicated that the mean, time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The data also indicate that the relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗

Computational study of wind-tunnel wall effects on flow field around delta wings

This paper addresses wind-tunnel wall effects on delta-wing flow fields using the Free Vortex Sheet (FVS) theory in support of planned subsonic wind-tunnel tests. The configurations include several sizes of a 65-deg delta wing in the NASA Langley Research Center Low-Turbulence Pressure Tunnel (LTPT), and an aspect ratio 1 delta wing in the Delft University low-speed tunnel. Standard upflow correction methodology is extended to account for angle-of-attack and nonplanar effects. Blockage and streamline curvature corrections are not applied in the present investigation. Resulting corrections to the 65-deg delta flow field were good for model-to-tunnel span ratios up to 0.5 and angles of attack up to 30-deg, both for linear attached flow and nonlinear vortex flow. For the aspect ratio 1 delta wing, corrections to the vortex flow field for the effect of the averaged upflow angle were satisfactory but streamline curvature effects were larger.

Frink, Neal T.↗

Numerical study of a ramjet dump combustor flow field

Increased interest in ramjet propulsion systems with higher performance requirements and tighter constraints on system size and weight has lead to the need for improved techniques for analyzing and designing such systems. A computer program has been developed to analyze the turbulent reacting flow field in a ramjet dump combustor configuration. The program solves the axisymmetric Navier-Stokes and species equations throughout the engine diffuser and combustor providing a unified analysis of the complete engine flow field, including flow separation, fuel-air mixing, and preliminary results with chemical reaction. Details of the program development are given, along with a comparison of program results with data from a dump combustor simulation experiment, to allow assessment of the flow field modeling that is employed.

Drummond, J. P.↗

A Study of Coaxial Rotor Performance and Flow Field Characteristics

As a precursor to studying the acoustics of a coaxial rotor system, the aerodynamics and flow field of a coaxial rotor were simulated to better understand the interaction between the two rotors. RotUNS, an unsteady Navier-Stokes solver that uses a simplified blade aerodynamics model, was used to predict coaxial rotor performance in hover and forward flight. RotUNS steady hover calculations showed improved performance compared to blade element momentum theory. Prior to examining the complex 3D flow field of a coaxial rotor in detail, two airfoils traveling in opposite directions with a vertical separation distance equivalent to the separation between the upper and lower rotor of the coaxial system were simulated. The pressure field generated by the two airfoils aided our interpretation of the more complex coaxial rotor system flow field. The pressure fields above, between, and below the coaxial rotor system were then examined for different azimuth positions of the upper and lower rotor blades.

Barbely, Natasha L.↗

Lava flow-field morphology: A case study from Mount Etna, Sicily

The morphology of lava flows is often taken as an indicator of the broad chemical composition of the lava, especially when interpreting extraterrestrial volcanoes using spacecraft images. The historical lavas of the active volcano Mount Etna in Sicily provide an excellent opportunity to examine the controls on flow field morphology. In this study only flow produced by flank eruptions after the middle of the 18th century are examined. The final form of a flow-field may be more indicative of the internal plumbing of the volcano, which may control such factors as the effusion, rate, duration of eruption, volume of available magma, rate of de-gassing, and lava rheology. Different flow morphologies on Etna appear to be a good indicator of differing conditions within the volcanic pile. Thus the spatial distribution of different flow types on an extraterrestrial volcano may provide useful information about the plumbing conditions of that volcano, rather than necessarily providing information on the composition of materials erupted.

Guest, J. E.↗

Planar measurement of flow field parameters in a nonreacting supersonic combustor using laser-induced iodine fluorescence

A nonintrusive optical technique, laser-induced iodine fluorescence, has been used to obtain planar measurements of flow field parameters in the supersonic mixing flow field of a nonreacting supersonic combustor. The combustor design used in this work was configured with staged transverse sonic injection behind a rearward-facing step into a Mach 2.07 free stream. A set of spatially resolved measurements of temperature and injectant mole fraction has been generated. These measurements provide an extensive and accurate experimental data set required for the validation of computational fluid dynamic codes developed for the calculation of highly three-dimensional combustor flow fields.

Hartfield, Roy J., Jr.↗

General design method for three-dimensional potential flow fields. 1: Theory

A general design method was developed for steady, three dimensional, potential, incompressible or subsonic-compressible flow. In this design method, the flow field, including the shape of its boundary, was determined for arbitrarily specified, continuous distributions of velocity as a function of arc length along the boundary streamlines. The method applied to the design of both internal and external flow fields, including, in both cases, fields with planar symmetry. The analytic problems associated with stagnation points, closure of bodies in external flow fields, and prediction of turning angles in three dimensional ducts were reviewed.

Stanitz, J. D.↗

A numerical solution of the flow field over a transonic airfoil including strong-shock-induced flow separation

An approximate numerical method has been developed for computing the entire transonic flow field over an airfoil, including the boundary layer, the shock-wave/boundary-layer interaction, and the shock-induced-separation. The inviscid flow, the turbulent boundary layer in the weak interaction zone, and the strong interaction elliptic region are solved separately. The inviscid flow is represented by the solution of the transonic small-disturbance equation, while the boundary layer is solved by the generalized Galerkin method, and the strong interaction region (including the wake) is computed from the time-averaged Navier-Stokes equations. A second-order interaction is computed iteratively using the inviscid pressure distribution as a boundary condition for the boundary layer and Navier-Stokes codes, and the viscous displacement thickness to modify the airfoil geometry for the inviscid computation. The computed pressure distributions and shock-wave profiles are compared with experimental data. Agreement is very good except that the pressure recovery on the trailing edge is greater than the experimental data.

Seginer, A.↗

Calculation of hypersonic forebody/inlet flow fields

The National Aero-Space Plane (NASP) is unique in its integration of the airframe and propulsion system. The performance of the NASP propulsion system (scramjet) is dependent upon the quality of the flow into the scramjet inlet. Hence, the calculation of the inlet flow field must be coupled to the forebody flow field for accurate performance predictions. The Compressible Navier-Stokes code has been extended to perform both external and internal hypersonic flow fields. Computations are presented that validate these changes and demonstrate the capability to perform coupled forebody/inlet computations for hypersonic flows.

Bennett, Bradford C.↗

Test Data of Flow Field of Shuttle SRM Nozzle Joint with Bond Defects, Using Unheated Air

The nozzle-to-case joint on the Shuttle SRM (as redesigned after the Challenger accident) features an adhesive sealant filling and bonding the joint, with a wiper O-ring to prevent the adhesive from reaching and disabling the closure O-ring. Flawless implementation of that joint design would ensure that hot, corrosive propellant combustion gases never reach the closure O-ring. However, understanding the flow field related to bonding defects is prudent. A comprehensive test program was conducted to quantify such flow fields and associated heating environments. A two-dimensional, full-scale model represented 65 inches of the nozzle joint, using unheated air as the test medium, in a blowdown mode. Geometry variations modeled RSRM assembly tolerances, and two types of bonding defects: pullaways and blowholes. A range of the magnitude of each type defect was tested. Also a range of operational parameters was tested, representative of the RSRM flow environment, including duplication of RSRM Mach and Reynolds numbers. Extensive instrumentation was provided to quantify pressures, heat rates, and velocities. The resulting data established that larger geometric defects cause larger pressure and larger heating, at the closure O-ring region. Velocity trends were not so straight-forward. Variations in assembly tolerances did not generally affect flow fields or heating. Operational parameters affected flow fields and heating as might be expected, increasing density or velocity increased heating. Complete details of this test effort are presented.

Hair, Leroy M.↗

Penn State axial flow turbine facility: Performance and nozzle flow field

The objective is to gain a thorough understanding of the flow field in a turbine stage including three-dimensional inviscid and viscid effects, unsteady flow field, rotor-stator interaction effects, unsteady blade pressures, shear stress, and velocity field in rotor passages. The performance of the turbine facility at the design condition is measured and compared with the design distribution. The data on the nozzle vane static pressure and wake characteristics are presented and interpreted. The wakes are found to be highly three-dimensional, with substantial radial inward velocity at most spanwise locations.

Lakshminarayana, B.↗

Investigation of wing upper surface flow-field disturbance due to NASA DC-8-72 in-flight inboard thrust-reverser deployment

An investigation of the wing upper surface flow-field disturbance due to in-flight inboard thrust reverser deployment on the NASA DC-8-72, which was conducted cooperatively by NASA Ames, the Federal Aviation Administration (FAA), McDonnell Douglas, and the Aerospace Industry Association (AIA), is outlined and discussed in detail. The purpose of this flight test was to obtain tufted flow visualization data which demonstrates the effect of thrust reverser deployment on the wing upper surface flow field to determine if the disturbed flow regions could be modeled by computational methods. A total of six symmetric thrust reversals of the two inboard engines were performed to monitor tuft and flow cone patterns as well as the character of their movement at the nominal Mach numbers of 0.55, 0.70, and 0.85. The tufts and flow cones were photographed and video-taped to determine the type of flow field that occurs with and without the thrust reversers deployed. In addition, the normal NASA DC-8 onboard Data Acquisition Distribution System (DADS) was used to synchronize the cameras. Results of this flight test will be presented in two parts. First, three distinct flow patterns associated with the above Mach numbers were sketched from the motion videos and discussed in detail. Second, other relevant aircraft parameters, such as aircraft's angular orientation, altitude, Mach number, and vertical descent, are discussed. The flight test participants' comments were recorded on the videos and the interested reader is referred to the video supplement section of this report for that information.

Hamid, Hedayat U.↗

Numerical flow field visualization

The application of computer-generated imagery to analyze numerical solutions of fluid flow is presented. High-performance graphics workstations, their current capabilities, and their use in flow field analysis are discussed. Interactive flow field computations about complex three-dimensional bodies applying computer-generated imagery are projected for the future.

Smith, Robert E.↗