SEARCH · Search NASA

Results for “Freestream conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2017

Off-Design Performance of a Streamline-Traced, External-Compression Supersonic Inlet

A computational study was performed to explore the aerodynamic performance of a streamline-traced, external-compression inlet designed for Mach 1.664 at off-design conditions of freestream Mach number, angle-of-attack, and angle-of-sideslip. Serious degradation of the inlet performance occurred for negative angles-of-attack and angles-of-sideslip greater than 3 degrees. At low subsonic speeds, the swept leading edges of the inlet created a pair of vortices that propagated to the engine face. Increasing the bluntness of the cowl lip showed no real improvement in the inlet performance at the low speeds, but did improve the inlet performance at the design conditions. Reducing the inlet flow rate improved the inlet performance, but at the likely expense of reduced thrust of the propulsion system. Deforming the cowl lip for low-speed operation of the inlet increased the inlet capture area and improved the inlet performance.

distortion↗

NASA NTRS2022

Stability Analysis of Streaks Induced by Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗

NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗

NASA NTRS2018

Blunt-Body Paradox and Improved Application of Transient-Growth Framework

The “Reshotko-Tumin transition criterion" based on optimal transient growth successfully correlates laboratory measurements of roughness induced transition over blunt body configurations. Even though transient growth has not been conclusively linked to the measured onset of transition, the above correlation denotes the only available physics-based model for subcritical transition in blunt body flows, since the latter do not support any modal instabilities at typical experimental conditions. Unlike other established models based on empirical curve fits that are valid for a specific subclass of datasets, the optimal-growth-based transition criterion appears to provide a reasonable correlation with measurements in various wind tunnel and ballistic range facilities and for a broad range of surface temperature ratios. This paper is focused on optimal growth calculations that improve upon significant shortcomings of the computations underlying the Reshotko-Tumin correlation. The improved framework is applied to leeward transition over a spherical section forebody that was tested in the Mach 6 Adjustable Contour Expansion wind tunnel at Texas A&M University. The computed results highlight the significance of nonparallel basic state evolution, curvature terms, and an optimization procedure that varies both inflow and outflow locations of the transient growth interval. More important, the results indicate that the modified correlation is very close to its original form, and hence, that the accuracy of the transient-growth-based transition criterion is not compromised by using a more thorough theoretical framework. Yet the results also show that the optimal energy gain up to the predicted transition onset location can be rather small, highlighting the need to further investigate the optimal growth criterion for additional experimental configurations and to also uncover the in-depth physics underlying blunt body transition.

Freestream conditions↗

NASA NTRS2019

Effect of 3D Roughness Patch on Instability Amplification in a Supersonic Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of high-speed vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, sinusoidal shape roughness elements on a Mach 3.5 flat plate boundary layer for flow conditions corresponding to the planned conditions of an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at the NASA Langley Research Center. Analysis of convective instabilities in the wake of the roughness patch was reported in a previous paper and the current work extends that analysis to instability amplification across the length of the roughness patch. Quasi-parallel stability analysis of the modified boundary layer flow over the patch indicates two dominant families of unstable disturbances, namely, a group of high frequency modes that amplify in localized regions along the roughness patch and another group of low frequency modes that have smaller peak amplification rates but amplify steadily both above the roughness patch and in the wake region behind it. The results suggest that the amplification factors associated with the high-frequency modes are sufficiently low, at least for the roughness patches considered in this paper, so that these modes are unlikely to have a major influence on the transition process. The amplification of the low-frequency modes within the region of the roughness patch is further quantified via direct numerical simulations. Results confirm the strongly destabilizing influence of the roughness patch on the first mode instabilities, yielding an N-factor increment of ΔN ≈ 3.6 for a roughness patch length of eight wavelengths.

Laminar turbulent transition↗

NASA NTRS1973

Penetration of retrorocket exhausts into subsonic counterflows.

Simulation experiments were performed in the NASA Langley Full Scale Tunnel to investigate the retroplume heating rates encountered by a lander vehicle during a terminal descent to a planetary surface. A 10% scale model of the Viking Lander with freestream velocity conditions from 37 to 75 ft/sec was used for simulation. The simulation test data were close to the theoretical predictions of Hill et al. (1971).

Jarvinen, P. O.↗

NASA NTRS1976

Engineering flowfields and heating rates for highly swept wing leading edges

An engineering flow model is developed (and verified experimentally) which describes the flowfield that arises when a supersonic stream encounters a wedge/cylinder configuration whose angles are such that the flow includes only weak shock waves. A numerical code using the perfect gas relations is used to describe the flow in the plane of symmetry inboard of the shock interaction region. Theoretical surface-pressure and heat-transfer distributions are computed for freestream velocities ranging from 1167 to 7610 m/sec. Nondimensionalization of the heat-transfer rates in terms of local flow parameters produced a correlation of Stanton number as a function of the local Reynolds number, which is independent of the freestream flow conditions and of the surface temperature.

Bertin, J. J.↗

NASA NTRS1979

A numerical study of jet entrainment effects on the subsonic flow over nozzle afterbodies

A viscous-inviscid interaction model has been developed which accounts for jet entrainment effects in the prediction of the subsonic flow over nozzle afterbodies. The jet entrainment model is based on the concept of a weakly interacting shear layer in which the local streamline deflections due to entrainment are accounted for by a displacement-thickness type correction to the inviscid plume boundary. The entire flowfield is solved in an iterative manner to account for the effects on the inviscid external flow of the turbulent boundary layer, turbulent mixing and chemical reactions in the shear layer, and the inviscid jet exhaust flow. The individual components of the computational model are described and numerical results are presented which illustrate the interactive effects of entrainment on the overall flow structure. The validity of the interactive model is assessed by comparisons with data obtained from flowfield measurements on cold-air jet exhausts. Numerical results and experimental data are also given which show the entrainment effects on nozzle boattail drag under various jet exhaust and freestream flow conditions.

Wilmoth, R. G.↗

NASA NTRS1981

Direct simulation Monte Carlo technique for modeling of the environment in the vicinity of the Space Shuttle Orbiter

A program for analyzing the flowfield parameters in the neighborhood of the Space Shuttle Orbiter has been developed. The program uses the direct simulation Monte Carlo method, which is a completely probabilistic Monte Carlo technique capable of analyzing 3-dimensional steady or unsteady flow with prescribed internal and external boundary conditions. The freestream flux densities incident on the external flowfield boundaries are calculated from the drifting Maxwellian gas properties of the freestream. The flux entering the flowfield from the internal boundary is calculated from the outgassing flux density distribution over the Shuttle external surface and the prescribed discrete source fluxes. This technique produces a numerical flowfield solution which is the probabilistic equivalent of a complete solution of the time-dependent, 3-dimensional Boltzmann equation. Flowfield results are presented for the following configurations: (1) Shuttle angles of attack of 0 and 90 deg, (2) freestream density 10 to the 9th - 10 to the 11th per cu cm, (3) Shuttle outgassing flux density, and (4) operation of the aft downfiring vernier Reaction Control System (RCS) engine. Results are presented for column density distribution of outgassed and engine species and for the flux density of outgassed and engine species incident on the Shuttle bay and the windshield.

Melfi, L. T., Jr.↗

NASA NTRS1987

Prediction and control of transition in hypersonic boundary layers

In this paper, the role of compressible linear stability theory in prediction of boundary layer transition at supersonic and hypersonic speeds is investigated. Computations for sharp cones, using the e exp N method with N = 10, show that the first oblique Tollmien-Schlichting mode is responsible for transition at adiabatic wall conditions for freestream Mach numbers up to 7. For cold walls, the two-dimensional second mode dominates the transition process at lower hypersonic Mach numbers due to the well-known destabilizing effect of cooling on the second mode. It is shown that pressure gradient and suction may be used to stabilize this mode. Some results on the real gas effects on hypersonic boundary-layer stability are presented.

Malik, Mujeeb R.↗

NASA NTRS1989

Vortex-dominated conical-flow computations using unstructured adaptively-refined meshes

A conical Euler/Navier-Stokes algorithm is presented for the computation of vortex-dominated flows. The flow solver involves a multistage Runge-Kutta time stepping scheme which uses a finite-volume spatial discretization on an unstructured grid made up of triangles. The algorithm also employs an adaptive mesh refinement procedure which enriches the mesh locally to more accurately resolve the vortical flow features. Results are presented for several highly-swept delta wing and circular cone cases at high angles of attack and at supersonic freestream flow conditions. Accurate solutions were obtained more efficiently when adaptive mesh refinement was used in contrast with refining the grid globally. The paper presents descriptions of the conical Euler/Navier-Stokes flow solver and adaptive mesh refinement procedures along with results which demonstrate the capability.

Batina, John T.↗

NASA NTRS1990

Application of a patched-grid algorithm to the F/A-18 forebody-leading-edge extension configuration

A patched-grid algorithm for the analysis of complex configurations with an implicit, upwind-biased Navier-Stokes solver is presented. Results from both a spatial-flux and a time-flux conservation approach to patching across zonal boundaries are presented. A generalized coordinate transformation with a biquadratic geometric element is used at the zonal interface in order to treat highly stretched viscous grids and arbitrarily shaped zonal boundaries. Applications are made to the F/A-18 forebody-Ieading-edge extension configuration at subsonic, high-alpha conditions. Computed surface flow patterns compare well with ground-based and flight-test results; the large effect of Reynolds number on the forebody flowfield is shown.

Leading edge extension↗

NASA NTRS1994

Navier-Stokes Flowfield Simulation of Boeing 747-200 as Platform for SOFIA

Steady and unsteady viscous, three-dimensional flowfields are calculated using a thin layer approximation of Navier-Stokes equations in conjunction with Chimera overset grids. The finite-difference numerical scheme uses structured grids and a pentadiagonal flow solver called "OVERFLOW". The configuration of Boeing 747-200 has been chosen as one of configurations to be used as a platform for the SOFIA (Stratospheric Observatory For Infrared Astronomy). Initially, the steady flowfield of the full aircraft is calculated for the clean configuration (without a cavity to house telescope). This solution is then used to start the unsteady flowfield of a configuration containing cavity housing the observation telescope and its peripheral units. Analysis of unsteady flowfield in the cavity and its influence on the tail empennage, as well as the noise due to turbulence and optical quality of the flow are the main focus of this study. For the configuration considered here, the telescope housing cavity is located slightly downstream of the portwing. The entire flow-field is carefully constructed using 45 overset grids and consists of nearly 4 million grid points. All the computations axe done at one freestream flow condition of M(sub infinity) = 0.85, alpha = 2.5deg, and a Reynolds of Re = 1.85x10deg

Srinivasan, G.R.↗

NASA NTRS1996

Comparison of Experimental and Computational Aerothermodynamics of a 70-deg Sphere-Cone

Numerical solutions for hypersonic flows of carbon-dioxide and air around a 70-deg sphere-cone have been computed using an axisymmetric non-equilibrium Navier-Stokes solver. Freestream flow conditions for these computations were equivalent to those obtained in an experimental blunt-body heat-transfer study conducted in a high-enthalpy, hypervelocity expansion tube. Comparisons have been made between the computed and measured surface heat-transfer rates on the forebody and afterbody of the sphere-cone and on the sting which supported the test model. Computed forebody heating rates were within the estimated experimental uncertainties of 10% on the forebody and 15% in the wake except for within the recirculating flow region of the wake.

Hollis, Brian R.↗

NASA NTRS1996

Hypervelocity Heat-Transfer Measurements in an Expansion Tube

A series of experiments has been conducted in the NASA HYPULSE Expansion Tube, in both CO2 and air test gases, in order to obtain data for comparison with computational results and to assess the capability for performing hypervelocity heat-transfer studies in this facility. Heat-transfer measurements were made in both test gases on 70 deg sphere-cone models and on hemisphere models of various radii. HYPULSE freestream flow conditions in these test gases were found to be repeatable to within 3-10%, and aerothermodynamic test times of 150 microsec in CO2 and 125 microsec in air were identified. Heat-transfer measurement uncertainty was estimated to be 10-15%. Comparisons were made with computational results from the non-equilibrium Navier-Stokes solver NEQ2D. Measured and computed heat-transfer rates agreed to within 10% on the hemispheres and on the sphere-cone forebodies, and to within 10% in CO2 and 25% in air on the afterbodies and stings of the sphere-cone models.

Hollis, Brian R.↗

NASA NTRS1990

Comparisons of a Three-Dimensional, Full Navier Stokes Computer Model with High Mach Number Combuster Test Data

Comparisons between scramjet combustor data and a three-dimensional full Navier-Stokes calculation have been made to verify and substantiate computational fluid dynamics (CFD) codes and application procedures. High Mach number scramjet combustor development will rely heavily on CFD applications to provide wind tunnel-equivalent data of quality sufficient to design, build and fly hypersonic aircraft. Therefore. detailed comparisons between CFD results and test data are imperative. An experimental case is presented, for which combustor wall static pressures were measured and flow-fieid interferograms were obtained. A computer model was done of the experiment, and counterpart parameters are compared with experiment. The experiment involved a subscale combustor designed and fabricated for the National Aero-Space Plane Program, and tested in the Calspan Corporation 96" hypersonic shock tunnel. The combustor inlet ramp was inclined at a 20 angle to the shock tunnel nozzle axis, and resulting combustor entrance flow conditions simulated freestream M=10. The combustor body and cowl walls were instrumented with static pressure transducers, and the combustor lateral walls contained windows through which flowfield holographic interferograms were obtained. The CFD calculation involved a three-dimensional time-averaged full Navier-Stokes code applied to the axial flow segment containing fuel injection and combustion. The full Navier-Stokes approach allowed for mixed supersonic and subsonic flow, downstream-upstream communication in subsonic flow regions, and effects of adverse pressure gradients. The code included hydrogen-air chemistry in the combustor segment which begins near fuel injection and continues through combustor exhaust. Combustor ramp and inlet segments on the combustor lateral centerline were modelled as two dimensional. Comparisons to be shown include calculated versus measured wall static pressures as functions of axial flow coordinate, and calculated path-averaged density contours versus an holographic Interferogram.

Watkins, William B.↗

NASA NTRS2022

Combined Bluntness and Roughness Effects on Cones at Hypersonic Speeds

This computational study investigates the effects of discrete roughness elements on a blunt cone at zero degrees angle of attack in a Mach 6 flow. Motivation was provided by experiments conducted in the Air Force Research Laboratory Mach 6 High Reynolds Number facility on a 7-degree half-angle cone with a roughness array located at 45 degrees from the apex on two nose tips of different blutness but equivalent roughness Reynolds number. Transition was only affected on the blunter cone, indicating that the transition onset is associated with the combined effects of bluntness and roughness. The present study investigates the 15.24 mm nose radius, 420 azimuthal wavenumber case via Navier-Stokes computations of the laminar base flow and instability analysis. Plane-marching parabolized stability equations (PSE) and inflow-resolvent analysis based on the three-dimensional, harmonic linearized Navier-Stokes equations (HLNSE) are used to calculate the amplification of disturbances along the roughness wake as well as over the roughness nearfield. Results show that the roughness shape can have a great impact on the characteristics of the most amplified wake instabilities. For the experimental configuration with cubic roughness elements of 15 μ m height, the flow is marginally unstable. For prismatic elements of 20 μ m height, the PSE predicts a logarithmic disturbance amplification ratio of N = 5.6 along its wake, but this ratio increases to N = 9.6 when the amplification over the roughness and separation regions is included in the inflow-resolvent analysis.

Boundary-layer transition↗

NASA NTRS2022

Stability Analysis of Streaks Induced By Optimized Vortex Generators

Boundary layer transition↗