SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A membrane assembly is provided. The membrane assembly includes a non-metallic, porous substrate. A graphene oxide membrane is formed over the non-metallic, porous substrate. A chemical linker interface covalently binds the graphene oxide membrane to the non-metallic, porous substrate.
A first process and sorbent for removing ammonia from a gaseous environment, the sorbent comprised of graphene oxide having supported thereon at least one compound selected from metal salts, metal oxides and acids, each of which is capable of adsorbing ammonia. A second process and sorbent system for removing ammonia and a volatile organic compound from a gaseous environment; the sorbent system comprised of two graphene-based materials: (a) the aforementioned graphene oxide, and (b) a nitrogen and oxygen-functionalized graphene. The sorbents are regenerable under a pressure gradient with little or no application of heat. The processes are operable through multiple adsorption-desorption cycles and are applicable to purifying and revitalizing air contaminated with ammonia and organic compounds as may be found in spacesuits, aerospace cabins, underwater vehicles, and other confined-entry environments.
Development of solid lubricant materials that render reliable performance in ambient conditions, are amenable to industrial size and design complexities, and work on engineered surfaces is reported. These coatings are composed of Ti 3 C 2 T x -Graphene Oxide blends, spray-coated onto bearing steel surfaces. The tribological assessment was carried out in ambient environmental conditions and high contact pressures in a ball-on-disc experimental set-up. The evaluation yielded that the use of Ti 3 C 2 T x -Graphene-Oxide coatings led to substantial reduction in friction down to 0.065 (at 1 GPa contact pressure and 100 mm/s) in comparison to the uncoated of single-component-coated surfaces, surpassing the state-of-the-art. The coatings also provided excellent protection against wear loss of the substrate and counter-face. The results were explained based on the observations from Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, and nanoindentation measurements. In operando formation of a dense, hard and stiff, dangling-bond-saturated tribolayer was observed to be the reason for the sustained lubricity even at high test loads and sliding speeds. This report presents the holistic exploration and correlation of structure-property-processing pertaining to the advancement of solid lubrication science.
In this work, ordered porous thin films of reduced graphene oxide and tin oxide (rGO/SnO 2 ) were synthesized by a polystyrene sphere monolayer colloidal crystal template method, and their gas-sensing properties were systematically studied. The formed amorphous SnO 2 and partially reduced graphene oxide were analyzed using several complementary material characterization techniques. Further, the results show that the incorporation of rGO significantly improved the humidity sensitivity and the electrical conductivity of the sensor relative to the pristine SnO 2 thin film. Fast response time and excellent selectivity towards humidity were also achieved for the rGO/SnO 2 composite film. The long-term stability of the rGO/SnO 2 sensor was confirmed by comparing its performance to a commercial humidity sensor. The enhanced sensor performance is attributed to the synergistic effects of the incorporation of rGO and the ordered porous structure of the composite film.
This study reports the design and development of a novel chemiresistor (CR) sensor using ion imprinted polymer (IIP)-functionalized reduced graphene oxide (rGO) [IIP/rGO-CR] for cadmium ions (Cd(II)) determination in water. The sensor consisted of a CR transducer made of rGO channel bridging source and drain electrodes prepared by self-assembly and thermal reduction of graphene oxide (GO) on Au interdigitated electrodes chip fabricated on Si/SiO 2 substrate. The IIP was then grafted on rGO using surface-initiated reversible addition-fragmentation chain transfer (RAFT) polymerization with polyethylenimine (PEI) and methylacrylic acid (MAA) as dual functional monomers and Cd(II) ions as template through UV light-initiated copolymerization. The IIP functionalized on rGO acted as an effective recognition element that modulated the resistance of rGO-CR upon binding of Cd(II), enabling Cd(II) detection at ppb level in aqueous solutions. The prepared IIP/rGO-CR sensor worked effectively in the linear range of 2~200ppb and achieved a limit of detection (LOD) of 0.83 ppb, which is lower than the World Health Organization guidelines of 3ppb for drinking water quality. The developed sensor of IIP/rGO-CR showed a high selectivity against a variety of trace and heavy metal ions found in water and good stability for up to 60 days when stored at room temperature for Cd(II) determination in water. Further, the sensor was successfully applied to analyzing Cd(II) spiked in tap, lake and river waters with a 94.5%–113.5% recovery, demonstrating a high degree of accuracy even in complex water samples. Finally, our results illustrated that the CR sensor of IIP functionalized rGO provides a potential platform for sensitive, robust and low-cost environmental analysis of Cd(II) in water.
In any electrochemical device, the separator or membrane allows specific ions to transport but blocks electrons and other chemical species, enabling the electrochemical energy to be harvested. However, small amounts of undesired species are known to permeate through the membrane, reducing overall system efficiency and lifetime. An emerging concept called the “Selective Transport Layer” preferentially allows only protons to pass through but reduces the permeance of other species by a meaningful degree. Here, in this study, we demonstrate that a 60 nm thick graphene oxide composite layer can be very effective in reducing gas and ion permeation, even for a gas as small as H 2 , while not noticeably increasing proton transport resistance. In electrode and membrane accelerated stability tests, we show that both electrode and membrane durability are improved by a factor of two. Microscopy and mathematic simulations confirm that the graphene oxide composite is effective in blocking transport of dissolved Pt 2+ . The improved durability and reduced H 2 fuel crossover are expected to substantially reduce initial and operating costs of the fuel cell system. How this technology may affect other membrane-based electrochemical devices is also discussed.
In the presence of contaminants, moisture probes can give false moisture readings and have shorter lifetimes. Absolute humidity probes are composed of porous, hygroscopic metallic oxide thin films (Al 2 O 3 ) coupled to electrodes (e.g. Au and Al). While these materials provide absolute humidity readings at low water levels at a relatively low cost, they are sensitive to the presence of contaminants, especially ammonia, due to its high hygroscopicity and ability to bind to the probe. Without frequent recalibration, especially in the presence of contaminants, the humidity levels are inaccurately reported due to measurement drift that occurs when the pores close, changing the impedance of the probe. The goal of this project was to improve the stability and reliability of these moisture probes by incorporating a molecular sieve into the probe to allow only the water to reach the sensor. Molecular sieves contain pores that allow molecule specific permeation. Two dimensional inorganic nanosheets (e.g. BN, MoO 2 , MoS 2 ) have recently been shown to behave as molecular sieves for water. Compared to zeolites, nanoporous materials have higher flux rates through the pores, leading to faster water permeation. Graphene oxide sheets have also been successfully employed for unimpeded water permeation; however, at lower humidity levels, the structure is unstable and the pores shrink, preventing the sieving of molecules. Compared to graphene oxide, sheets based off of inorganic materials, such as molybdenum, have been found to be more stable at lower humidity levels and have faster permeation rates. By creating a barrier in before the Al 2 O 3 sensor chip to prevent the permeation of contaminants into the probe, the lifetime of the probe will be extended. While the molybdenum sheets are a promising material for this application, their performance against ammonia and tritiated compounds have not yet been evaluated. This technology can be applied to other applications, including gas and liquid purification for environmental remediation, single molecule sensors, field effect transistors, and catalysts.
Sodium ion batteries are an emerging candidate to replace lithium ion batteries in large-scale electrical energy storage systems due to the abundance and widespread distribution of sodium. Despite the growing interest, the development of high-performance sodium cathode materials remains a challenge. In particular, polyanionic compounds are considered as a strong cathode candidate owing to their better cycling stability, a flatter voltage profile, and stronger thermal stability compared to other cathode materials. Here, we report the rational design of a biomimetic bone-inspired polyanionic Na3V2(PO4)3-reduced graphene oxide composite (BI-NVP) cathode that achieves ultrahigh rate charging and ultralong cycling life in a sodium ion battery. At a charging rate of 1 C, BI-NVP delivers 97% of its theoretical capacity and is able to retain a voltage plateau even at the ultra-high rate of 200 C. It also shows long cycling life with capacity retention of 91% after 10 000 cycles at 50 C. The sodium ion battery cells with a BI-NVP cathode and Na metal anode were able to deliver a maximum specific energy of 350 W h kg−1 and maximum specific power of 154 kW kg−1. In situ and postmortem analyses of cycled BI-NVP (including by Raman and XRD spectra) HRTEM, and STEM-EELS, indicate highly reversible dilation–contraction, negligible electrode pulverization, and a stable NVP-reduced graphene oxide layer interface. The results presented here provide a rational and biomimetic material design for the electrode architecture for ultrahigh power and ultralong cyclability of the sodium ion battery full cells when paired with a sodium metal anode.
The derivatives of the spectra are commonly used for quantification in Auger Electron Spectroscopy (AES) spectra, while the derivative of the KLL C Auger line has proven to be valuable in obtaining a measure of the relative proportions of sp 2 ‐ and sp 3 ‐hybridization using the D‐parameter in both AES and X‐ray Photoelectron Spectroscopy (XPS). Differentiation of X‐ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES) spectra by numerical means is presented and illustrated for polymeric, such as PEEK and Nylon, as well as for graphitic materials including highly ordered pyrolytic graphite and graphene oxide. The most commonly available Savitzky–Golay method is explained mathematically and developed through the case of constructing a 5‐point quadratic polynomial convolution kernel suitable for differentiating spectra of adequate signal to noise. The concept of differentiation of spectra where signal to noise is less than adequate is also developed. Two alternative strategies to Savitzky–Golay differentiation are presented, which fit curves to data that allow derivatives to be obtained where Savitzky–Golay would otherwise fail. These alternative methods involve constructing a parametric curve that fits data over the entire energy interval of interest. Derivatives of spectra are then obtained by differentiating these parametric curves directly. A comparison of results for different materials for which specific sp 2 ‐ vs sp 3 ‐hybridized carbon proportions are of interest is used to emphasize the importance of characterizing methods used to differentiate spectra and understanding the characteristics of instrumentation used to measure spectra. The case for using Principal Component Analysis noise reduction with C KLL spectra is made for spectra collected from a heterogeneous graphene oxide sample.
Not Available
Graphene oxide (GO) emulsions have been widely adopted to fabricate lightweight graphene aerogels (GAs). However, preparing high-performance GAs from conventional GO emulsions under ambient conditions seems rather challenging because of the structural collapse caused by strong capillary forces during drying. Here, we report a new, low-cost route to prepare high-performance, multifunctional GAs by the ambient drying of GO/camphene emulsions. Benefiting from the liquid-solid and solid-gas phase transitions of camphene, highly porous GO aerogels were obtained under ambient conditions. Moreover, the thermally annealed GO aerogels exhibited excellent mechanical properties, fire resistance, thermal insulation performance, and oil adsorption capability.
The balance of bacterial populations in the human body is critical for human health. Researchers have aimed to control bacterial populations using antibiotic substrates. However, antibiotic materials that non-selectively kill bacteria can compromise health by eliminating beneficial bacteria, which leaves the body vulnerable to colonization by harmful pathogens. Due to their chemical tunablity and unique surface properties, graphene oxide (GO)-based materials – termed “functional graphenic materials” (FGMs) – have been previously designed to be antibacterial but have the capacity to actively adhere and instruct probiotics to maintain human health. Numerous studies have demonstrated that negatively and positively charged surfaces influence bacterial adhesion through electrostatic interactions with the negatively charged bacterial surface. We found that tuning the surface charge of FGMs provides an avenue to control bacterial attachment without compromising vitality. Using E. coli as a model organism for gram-negative bacteria, we demonstrate that negatively charged Claisen graphene (CG), a reduced and carboxylated FGM, is bacterio-repellent through electrostatic repulsion with the bacterial surface. Though positively charged poly-L-lysine (PLL) is antibacterial when free in solution by inserting into the bacterial cell wall, here, we found that covalent conjugation of PLL to CG (giving PLLn-G) masks the antimicrobial activity of PLL by restricting polypeptide mobility. This allows the immobilized positive charge of the PLLn-Gs to be leveraged for E. coli adhesion through electrostatic attraction. We identified the magnitude of positive charge of the PLLn-G conjugates, which is modulated by the length of the PLL peptide, as an important parameter to tune the balance between the opposing forces of bacterial adhesion and proliferation. We also tested adhesion of gram-positive B. subtilis to these FGMs and found that the effect of FGM charge is less pronounced. B. subtilis adheres nondiscriminatory to all FGMs, regardless of charge, but adhesion is scarce and localized. Overall, this work demonstrates that FGMs can be tuned to selectively control bacterial response, paving the way for future development of FGM-based biomaterials as bacterio-instructive scaffolds through careful design of FGM surface chemistry.
A low friction, wear-resistant surface operable at high temperatures and high loads with a low coefficient of friction including boron nitride and graphene-oxide on steel or nanodiamonds and graphene on aluminum. The low friction, wear-resistant surface remains with a coefficient of friction in the superlubric regime at temperatures in between about 200° C. and 970° C.
Here, this study examines a facile technology to manufacture food packaging alternatives with superior mechanical, ultra-flexible, gas barrier and self-cleaning properties, based on green and benign starting materials. A novel galactomannan (GM) was isolated from the Sesbania cannabina seeds, which was used as a matrix for the fabrication of GM-based films. Inspired by the brick-and-mortar structure of natural nacre, a facile method was adopted to fabricate an artificial nacre based on the self-assembly of GM and borate crosslinked graphene oxide (GO). These GM/GO composites are ultra-flexible, which can be folded into various shapes. The tensile strength reached 135.54 MPa which is 2.40 times that of the pure GM film. In addition, after coating with the poly(dimethylsiloxane) (PDMS), these films became hydrophobic (WCA around 120°) with self-cleaning properties. Our study further revealed that the oxygen and water vapor permeabilities were improved with the introduction of GO and PDMS coating.
Graphene oxide (GO)-based energy storage faces dual bottlenecks: unsustainable reduction methods and sluggish proton transfer kinetics. Here, we introduce a groundbreaking green strategy using lignin-derived vanillyl alcohol (VA) as a dual-function monomer to simultaneously address these challenges. By thermally annealing GO/VA films at mild temperatures (<100 °C), VA triggers an interface-confined reduction of GO while self-polymerizing into redox-active oligomers (P-VA) that intercalate between graphene layers. This dual role-reducing agent and proton highway enables a 3D conductive network with minimized graphene restacking, abundant redox sites, and rapid H + transport pathways. Density Functional Theory (DFT) reveals how P-VA optimizes proton dynamics, while the resulting rGO-P-VA4-T90 electrode achieves a record volumetric capacitance of 311.1F/cm 3 (777.8F/cm 2 ) and retains 87.8 % capacity after 10,000 cycles. Flexible solid-state supercapacitors deliver 94.2 μWh/cm 2 energy density at 63.8 μW/cm 2 , rivaling state-of-the-art devices. Furthermore, this work redefines sustainable graphene engineering, merging biomass valorization with high-performance energy storage in a scalable, eco-friendly paradigm.
According to the increasing demands for shortening the battery charging time, high current rate (C-rate) performances become more significant in practical applications. With a higher theoretical capacity, lithium-sulfur batteries are treated as promising candidates for the next-generation batteries. In this work, the utilization of graphene nanoribbons (GNRs) exhibits the benefits in conductivity and other electrochemical performances, especially for high-rate applications. With air-controlled electrospray as the method, carbon encapsulated sulfur particles, poly(acrylic acid), reduced graphene oxide (rGO) sheets, and GNRs are mixed and directly deposited onto the carbon coated aluminum collector, to employ as the cathode. The scanning electron microscopy (SEM) imaging exhibits that the two-dimensional structure of GNRs helps construct inter-connected networks. This improved structure of cathode can increase the electroconductivity, confirmed by the electrochemical impedance spectroscopy (EIS), and modify the porosity, indicated through pore size distribution profiles. In this way, the polysulfides can be more efficiently trapped and utilized, realizing the promising behavior with faster charge transfer. In terms of the cycling performance at 0.2 C, the batteries with GNRs can perform 18% higher in capacity than those without GNRs, without decreasing the charge retention. According to the rate-capability tests, systems with GNRs can achieve enhanced performance compared to batteries with precursor carbon nanotubes (CNTs), especially at high C-rates. At 2 C, with 80 wt % of graphene-based materials as GNRs, batteries can achieve an increase in capacity by 78% and 41% compared with systems without GNRs and those with CNTs, respectively. Accordingly, the results testify the synergy of GNRs and rGO sheets in Li-S batteries.
Capacitive deionization (CDI) offers a cost-effective and low-energy method for selective removal of Pb 2+ from drinking water. Modifying CDI electrode surfaces with functional groups presents a versatile approach to enhancing selective ion adsorption capacity. However, a comprehensive understanding of the selectivity and removal efficiency of Pb 2+ among diverse functional groups remains unexplored. Here, we investigated the effects of different functional groups (-SH, -COOH, and -NH 2 ) attached to the graphene oxide (GO) electrode surfaces on Pb 2+ selectivity and removal efficiency. Surprisingly, GO-COOH demonstrated single-atom adsorption of Pb 2+ , displaying superior removal efficiency and selectivity compared with -SH and -NH 2 , although -SH possesses significant chelation capability for Pb 2+ . Both density functional theory (DFT) calculations and X-ray pair distribution function (PDF) analyses confirmed that Pb 2+ exhibits a theoretically higher affinity to -COOH. Further, this research deepens our understanding of the interactions between functional groups and heavy metal ions, enabling selective and rapid separation of target cations for water purification.
Abstract Metal amides are attractive candidates for hydrogen storage due to their high volumetric and gravimetric hydrogen densities. However, the sluggish kinetics and competing side reactions during hydrogen uptake and release limit their practical use. Here, a novel nanoconfined Li 2 Mg(NH) 2 @reduced graphene oxide (rGO) composite is presented, which is fabricated using a melt‐infiltration method with a minimum weight penalty of only 2 wt.%. The presence of rGO ensures close contact between the active phases, effectively preventing aggregation during cycling process. As a result, the reversible capacity of Li 2 Mg(NH) 2 @rGO reaches 4.42 wt.%, with no capacity degradation observed after multiple cycling. Theoretical calculations show that rGO catalyzes the hydrogen bond cleavage at the Mg‐amide/Li hydride interface, leading to local dehydrogenation hotspots and significantly improves kinetics of dehydrogenation compared to the bulk counterpart. This study provides a promising strategy for designing metal imide‐based composites to overcome the kinetic limitations and improve their reversible hydrogen storage performance.