Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Time-resolved spectroscopy of CI and CII line emissions from an ultrafast laser induced solid graphite plasma

We present an experimental characterization of the evolution dynamics of CI and CII lines in an ultrafast laser produced graphite plasma under various ambient conditions. Fast and slow components are observed in the temporal evolution of CI transition at 658.7 nm (3p{sup 1}P - 4d{sup 1}P{sup 0}) and CII transition at 426.7 nm (3d {sup 2}D - 4f {sup 2}F{sup 0}). Fast peak is due to the recombination of fast ions species with electrons, found to have an increase in velocity upon increasing the ambient pressure. Whereas the slow peaks in both cases can be the results of slow ions or slow neutrals in the plume.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermal oxidation of nuclear graphite and pyrolytic carbon coatings

The oxidation of pyrolytic carbon (PyC) deposited via fluidized bed chemical vapor deposition was characterized and compared with that of standard nuclear-grade graphite. The materials were heated at 700 to 1000 °C in a thermogravimetric analysis system under 20% v/v O 2 flow, allowing for direct comparison of dynamic oxidative mass change in each material. Further, three different PyC samples fabricated under different conditions exhibited variation in total mass loss and mass loss rate, varying by as much as 709 mg/cm 2 in total mass loss and 14.2 (mg/cm 2 )/min in mass loss rate at a single temperature. These variations highlight the correlation between PyC microstructure/defect density and oxidation susceptibility. Additionally, changes in the microstructure and composition between PyC and graphite were characterized via scanning electron microscopy and correlated to the mass loss results. The results of this work have implications toward the safety of tristructural isotropic (TRISO) and other coated particle fuels, especially under off-normal conditions, given the limited information that exists about the oxidation behavior of PyC.

36 MATERIALS SCIENCE↗

Progress Report on Graphite-Salt Interaction Studies (FY21)

This report summarizes the activities performed in FY21 to investigate the interactions between nuclear graphite and molten salts, such as FLiNaK. First, building on last year’s achievements, the team improved the procedure for measurements on pressurized salt intrusion in nuclear graphite and performed new experiments at variable pressures with specimens of different sizes and shapes. Additionally, the team actively provided suggestions and comments for ASTM D8091, Standard Guide for Impregnation of Graphite with Molten Salts , which came up for periodic revision in 2021. Second, the team expanded its capabilities to further characterize salt-impregnated graphite by procuring and installing a laser-induced breakdown spectroscopy (LIBS) instrument capable of producing a 3D chemical composition of a surface and subsurface region of specimens. A methodology for accurately analyzing information was developed, and a manuscript was submitted for publication. The LIBS instrument sample cell is sealed in controlled inert atmosphere, which is an advantage for using humidity-sensitive samples and Be-contaminated samples. This aligns with the team’s effort to expand the capabilities of handling FLiBe and Becontaining materials in two newly installed glovebox units. Third, the team performed preliminary tribology tests for pebble graphite wear in contact with stainless steel in dry state and in molten salt at high temperature. These tests are needed to establish the baseline for the wear of pebble graphite by friction against metallic walls. The friction and wear of pebbles in the fluoride salt-cooled hightemperature reactor are expected to generate dust, which is a concern for other components’ properties and safe reactor operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

AGC-4 Graphite Preirradiation Data Analysis Report

The Advanced Reactor Technology (ART) Graphite R&D program is conducting an extensive graphite irradiation program to provide data for licensing of a high temperature reactor (HTR) design. In past applications, graphite has been used effectively as a structural and moderator material in both research and commercial high temperature gas cooled reactor (HTGR) designs. Nuclear graphite H 451, used previously in the United States for nuclear reactor graphite components, is no longer available. New nuclear graphite grades have been developed and are considered suitable candidates for new HTR reactor designs. To support the design and licensing of new HTR core components within a commercial reactor, a complete properties database must be developed for these current grades of graphite. Quantitative data on in service material performance is required for the physical, mechanical, and thermal properties of each major graphite grade with a specific emphasis on data accounting for the life limiting effects of irradiation creep on key physical properties of the HTR candidate graphite grades. Further details on the research and development activities and associated rationale required to qualify nuclear grade graphite for use within the HTR are documented in the graphite technology research and development plan. Based on experience with previous graphite core components, the phenomenon of irradiation induced creep within the graphite has been shown to be critical to the total useful lifetime of graphite components. Irradiation induced creep occurs under the simultaneous application of high temperatures, neutron irradiation, and applied stresses within the graphite components. Significant internal stresses within the graphite components can result from a second phenomenon—irradiation induced dimensional change—where the graphite physically changes (i.e., first shrinking and then expanding with increasing neutron dose). This disparity in material volume change can produce significant internal stresses within graphite components. Irradiation induced creep relaxes these large internal stresses, thus reducing the risk of crack formation and component failure. Obviously, higher irradiation creep levels tend to relieve more internal stress, thus allowing the components longer useful lifetimes within the core. Determining the irradiation creep rates of nuclear grade graphite is critical for determining the useful lifetime of graphite components and is a major component of the Advanced Graphite Creep (AGC) experiment. The AGC experiment is currently underway to determine the in service behavior of these new graphite grades for HTR and molten salt reactor designs. This experiment will examine properties and behavior of nuclear grade graphite over a large spectrum of temperatures, irradiation fluencies and applied stress levels that are expected to cause irradiation creep strains within a HTR graphite component. Irradiation data are provided through the AGC test series, which is comprised of six planned capsules irradiated in the Advanced Test Reactor (ATR) in a large flux trap located at Idaho National Laboratory (INL). Each irradiation capsule consists of over 400 graphite specimens that are characterized before and after irradiation to determine the irradiation induced material properties changes and life-limiting irradiation creep rate for each graphite grade.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Laser-induced dehydration of graphite oxide coatings on polymer substrates

Nanosized graphite has been oxidized by the Hummers method to give high quality graphite oxide. This reaction is characterized by a very fast kinetic behavior and a high yield. The produced graphite oxide has been conveniently used to pattern graphene by using a standard photolithographic method, and the resulting systems have been characterized by optical microscopy (OM), scanning electron microscopy (SEM) and by Fourier transform infrared spectroscopy (FT-IR) and Visible-Near Infrared spectroscopy (Vis-NIR)

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Historic and modern nuclear graphite impurities: Pathways to improved waste strategies

Graphite has been used in large volumes as a structural material and neutron moderator since the earliest days of nuclear fission. However, no international consensus exists on the disposal of irradiated graphite, leaving much of the historic radioactive graphite inventory in interim vault or silo storage. With several new graphite-moderated reactors planned or under construction, the issue of graphite waste management is becoming increasingly urgent. This paper reviews and quantifies impurities in both historic and modern nuclear graphite, with emphasis on nitrogen—responsible for much of the 14 C inventory—and chlorine, which plays a critical role in repository performance and design. Modern graphites, benefitting from stringent quality-control measures developed for non-nuclear industries, meet or exceed the ASTM Ultra-High Purity nuclear standards, even without halide purification. Both chlorine and nitrogen concentrations have declined over time. For chlorine, identified as a key impurity influencing U.S. waste repository design, we propose a target of 0.1 appm in as-fabricated billets as a reasonable benchmark. Nitrogen sources are traced throughout the graphite production process, with surface and bulk concentrations characterized for all materials studied. Modern graphites commonly exhibit nitrogen levels below 5 appm, with values approaching 1 appm achievable. Using such reduced-nitrogen grades is critical to keeping graphite-induced radioactivity below the greater-than-Class-C waste threshold, thereby avoiding disposal cost penalties of nearly an order of magnitude.

Chlorine↗

Carbon nanomaterial produced by microwave exfoliation of graphite oxide: new insights.

We present detailed characterization of graphene-like material obtained through microwave stimulated exfoliation of graphite oxide (GO). Properties of this material were studied by multiple techniques including, among others, X-ray photoelectron spectroscopy, mass-spectroscopy, infrared and Raman spectroscopy, scanning electron microscopy and broadband dielectric spectroscopy. Specific surface area and volume of microwave exfoliated graphite oxide reached 600 m2 g1 and 6 cm3 g1, respectively. It is shown that during such an explosive reduction process the sample emits CO2, CO and H2O and, in some cases, SO2 gases. The resulting reduced material exhibits IR spectra similar to that of graphite and a dc-conductivity of 0.12 S cm1.

Shulga, Y. M.↗

Slides for MS&T2022: Carbon-Carbon Composites from 3D Printed Preforms Graphitized by Electric Field Assisted Sintering

Formation of Carbon-Carbon (C-C) composite materials requires putting a carbon fiber preform through a cycle of densification, carbonization, and graphitization. This cycle is then repeated until the desired properties are achieved. The graphitization phase is particularly energy demanding as it involves heating the components to in excess of 2000°C. In traditional furnaces this is also quite time consuming as typical heating rates are low, and the actual heat treatment may be limited by component dimensions, as heat is conducted throughout the part primarily by thermal diffusion. Joule heating by means of Electric Field Assisted Sintering (EFAS) systems enables high heating rates and causes the part to be heated from the inside, which eliminates the thermal diffusion time constraint. In our process, C-C composites are formed by pyrolyzation of 3D-printed carbon fiber preforms, vacuum infiltration of naphthalene based mesophase pitch, and carbonization. The part is then graphitized in the EFAS system. By this method graphitization of the composite matrix was achieved in less than an hour. A part density of greater than 1.6g/cc (up to 1.9g/cc demonstrated) was achieved after only two rounds of infiltration and a single graphitization. Overall the process took less than a week which is significantly faster than traditional methods. Optical microscopy and XRD results are discussed to elucidate the internal porosity and characterize the degree of graphitization. Testing was performed showing the impact on fiber direction to electrical and thermal properties of the final part.

36 MATERIALS SCIENCE↗

FY-2010 AGC-1 Disassembly Preparation

The Next Generation Nuclear Plant Project Graphite Research and Development program is currently establishing the safe operating envelope of graphite core components for a very high temperature reactor design. The program is generating quantitative data necessary for predicting the behavior and operating performance of the new nuclear graphite grades. To determine the in-service behavior of the graphite for pebble bed and prismatic designs, the Advanced Graphite Creep (AGC) experiment is underway. This experiment is examining the properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluencies, and compressive loads. Each experiment consists of over 400 graphite specimens that are characterized prior to irradiation and following irradiation. Six experiments are planned with the first, AGC-1, currently being irradiated in the Advanced Test Reactor and preirradiation characterization of the second, AGC-2, completed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Characterization of Al 4 C 3 in Aluminum-Graphite Composite Prepared by Electron-Beam Melting

We prepared graphite infused aluminum composites by electron-beam vacuum melting and electromagnetic stirring with 0% and 4wt% graphite addition. Bulk density of 2.69 g/cm 3 was measured for samples with 0% graphite addition (AlCv0) and 2.66 g/cm 3 for samples with 4 wt% graphite addition (AlCv4). Both are >99% of their theoretical values. X-ray diffraction indicated that AlCv0 is phase pure, while the AlCv4 sample is a composite consisting of aluminum, Al 4 C 3 , and graphite. Electron microscopy and energy dispersive X-ray spectroscopy revealed pockets of carbon rich phase of 10 to 50 μm in sizes dispersed in the Al matrix in AlCv4. Scanning transmission electron microscopy (STEM) showed that Al 4 C 3 crystallites of 1-2 μm sizes that are mostly located near the outer shell of the pockets of carbon rich phase and with undissolved graphite at the center. Thermal conductivity of 107.8 W/m·K was measured for the AlCv4 and 226.7 W/m·K for the AlCv0. Our work demonstrated the feasibility of producing pore-free high density graphite infused aluminum composite materials by electron-beam melting and electromagnetic stirring in vacuum.

36 MATERIALS SCIENCE↗

XRD and SANS evaluation of HOPG and Polycrystalline Graphite

As the primary construction material used in gas-cooled reactor cores, either of high-temperature (HTR) or very high-temperature (VHTR) design, nuclear graphite must be well characterized and variations in its properties upon high-energy neutron irradiation must be known, understood, and predict ed as accurately as possible before a reactor is built and operational. However, even after more than 70 years of operation of graphite-moderated reactors and intense research on graphite’s behavior in an extreme environment created by high temperatures, irradiation, mechanical stress, and chemically reactive (oxidizing) gaseous environment, questions still remain.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multi-modal characterization methods of solid-electrolyte interphase in silicon-graphite composite electrodes

Composite silicon-graphite (Si-Gr) anodes can improve battery energy density, due to Si's high gravimetric capacity, while mitigating mechanical degradation of the anode and solid-electrolyte interphase (SEI) caused by Si volumetric expansion. Optimizing these anodes is challenging, in part due to difficulty characterizing the SEI structure and composition. In this work, we present multi-modal characterization of the SEI on composite Si-Gr anodes to relate SEI chemical composition and structure to functional properties. Discrepancies in elemental concentrations from X-ray photoelectron spectroscopy, Auger electron spectroscopy, and energy-dispersive X-ray spectroscopy (EDS) are attributed to varying information depth and lateral resolution of the individual probes. However, by combining quantitative composition information with spatially resolved element mapping from scanning transmission electron microscopy, EDS, and electron energy loss spectroscopy, a holistic picture of the SEI emerges. We observe the bilayer SEI structure and a direct correlation between elemental Li and F, suggesting that most Li in the SEI exists as lithium fluoride (LiF). Further, LiF concentration is directly proportional to the maximum SEI resistivity, as determined by scanning spreading resistance microscopy. Lastly, there is an inverse relationship between lithium carbonate and LiF concentration in the SEI, providing insight into the detailed chemistry of SEI formation and evolution.

25 ENERGY STORAGE↗

Understanding Interfaces in Metal-Graphitic Hybrid Nanostructures”

Metal–graphitic interfaces formed between metal nanoparticles (MNPs) and carbon nanotubes (CNTs) or graphene play an important role in the properties of such hybrid nanostructures. This Perspective summarizes different types of interfaces that exist within the metal–carbon nanoassemblies and discusses current efforts on understanding and modeling the interfacial conditions and interactions. Characterization of the metal–graphitic interfaces is described here, including microscopy, spectroscopy, electrochemical techniques, and electrical measurements. Recent studies on these nanohybrids have shown that the metal–graphitic interfaces play critical roles in both controlled assembly of nanoparticles and practical applications of nanohybrids in chemical sensors and fuel cells. Better understanding, design, and manipulation of metal–graphitic interfaces could therefore become the new frontier in the research of MNP/CNT or MNP/graphene hybrid systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

AGC-2 Graphite Pre-irradiation Data Package

The NGNP Graphite R&D program is currently establishing the safe operating envelope of graphite core components for a Very High Temperature Reactor (VHTR) design. The program is generating quantitative data necessary for predicting the behavior and operating performance of the new nuclear graphite grades. To determine the in-service behavior of the graphite for pebble bed and prismatic designs, the Advanced Graphite Creep (AGC) experiment is underway. This experiment is examining the properties and behavior of nuclear grade graphite over a large spectrum of temperatures, neutron fluences and compressive loads. Each experiment consists of over 400 graphite specimens that are characterized prior to irradiation and following irradiation. Six experiments are planned with the first, AGC-1, currently being irradiated in the Advanced Test Reactor (ATR) and pre-irradiation characterization of the second, AGC-2, completed. This data package establishes the readiness of 512 specimens for assembly into the AGC-2 capsule.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Highly Active and Stable Graphene Tubes Decorated with FeCoNi Alloy Nanoparticles via a Template-Free Graphitization for Bifunctional Oxygen Reduction and Evolution

Development of highly active and stable bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts from earth–abundant elements remains a grand challenge for highly demanded reversible fuel cells and metal–air batteries. Carbon catalysts have many advantages over others due to their low cost, excellent electrical conductivity, high surface area, and easy functionalization. However, they typically cannot withstand the highly oxidative OER environment. Here, a new class of bifunctional electrocatalyst is reported, consisting of ultralarge sized nitrogen doped graphene tubes (N–GTs) (>500 nm) decorated with FeCoNi alloy particles. These tubes are prepared from an inexpensive precursor, dicyandiamide, via a template–free graphitization process. The ORR/OER activity and the stability of these graphene tube catalysts depend strongly on the transition metal precursors. The best performing FeCoNi–derived N–GT catalyst exhibits excellent ORR and OER activity along with adequate electrochemical durability over a wide potential window (0–1.9 V) in alkaline media. Here, the measured OER current is solely due to desirable O 2 evolution, rather than carbon oxidation. Extensive electrochemical and physical characterization indicated that high graphitization degree, thicker tube walls, proper nitrogen doping, and presence of FeCoNi alloy particles are vital for high bifunctional activity and electrochemical durability of tubular carbon catalysts.

36 MATERIALS SCIENCE↗