Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULLS - IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1930

Calculation of Pressure Distribution on Airship Hulls

These calculations were based on the shape of the ZR III, with the following simplifications: cars, fins, and rudders removed; all cross sections replaced by equivalent circular cross sections. Under these assumptions the pressure distribution was calculated for the following cases: symmetrical case, or flow parallel to the axis; unsymmetrical case, or flow at an angle to the axis. In both cases the simple potential flow first forms the basis for the determination of the pressure distribution.

Von Karman, Theodor↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-Boat Hull - N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M.↗
NASA NTRS1979

The Inertia Coefficients of an Airship in a Frictionless Fluid

The apparent inertia of an airship hull is examined. The exact solution of the aerodynamical problem is studied for hulls of various shapes with special attention given to the case of an ellipsoidal hull. So that the results for the ellipsoidal hull may be readily adapted to other cases, they are expressed in terms of the area and perimeter of the largest cross section perpendicular to the direction of motion by means of a formula involving a coefficient kappa which varies only slowly when the shape of the hull is changed, being 0.637 for a circular or elliptic disk, 0.5 for a sphere, and about 0.25 for a spheroid of fineness ratio. The case of rotation of an airship hull is investigated and a coefficient is defined with the same advantages as the corresponding coefficient for rectilinear motion.

Bateman, H.↗
NASA NTRS1924

The Inertial Coefficients of an Airship in a Frictionless Fluid

This report deals with the investigation of the apparent inertia of an airship hull. The exact solution of the aerodynamical problem has been studied for hulls of various shapes and special attention has been given to the case of an ellipsoidal hull. In order that the results for this last case may be readily adapted to other cases, they are expressed in terms of the area and perimeter of the largest cross section perpendicular to the direction motion by means of a formula involving a coefficient K which varies only slowly when the shape of the hull is changed, being 0.637 for a circular or elliptic disk, 0.5 for a sphere, and about 0.25 for a spheroid of fineness ratio 7. For rough purposes it is sufficient to employ the coefficients, originally found for ellipsoids, for hulls otherwise shaped. When more exact values of the inertia are needed, estimates may be based on a study of the way in which K varies with different characteristics and for such a study the new coefficient possesses some advantage over one which is defined with reference to the volume of fluid displaced. The case of rotation of an airship hull has been investigated also and a coefficient has been defined with the same advantages as the corresponding coefficient for rectilinear motion.

Bateman, H↗
DOE OSTI2024

Smart Adaptive Structures for an Ocean Wave Energy Converter

Ocean wave energy converters face significant challenges including cost-effectiveness, minimizing maintenance requirements, and withstanding extreme conditions. However, by utilizing smart materials, these converters could overcome these challenges. Such energy harvesters could use dielectric elastomer generators to convert ocean wave energy into electricity through their dynamic straining. Conversely, by applying electricity to these generators, they become actuators - dielectric elastomer actuators - thereby enabling them to alter their stiffness and adapt to the ever-changing ocean energy environments. Such active adaptation could enhance the converter's ability to: reach resonance with ocean waves and protect itself from dangerous waves. This study utilizes numerical analyses through the COMSOL software framework to evaluate the potential energy that could be harvested by a conceptual ocean wave energy converter based upon dielectric elastomer generators/actuators. The converter is composed of an external hull (that is a hollow cylinder), an inertial mass (that is a hollow cylinder and concentric with the hull), and 'spokes' - made of dielectric elastomer generators/actuators - that connect the hull to the inertial mass. Results of the numerical analyses include those outcomes arising from the conceptual converter being simulated via a sinusoidal motion analogous to ocean waves. That motion, therefore, causes relative motion between the converter's hull and inertial mass thereby dynamically stretching the corresponding connecting elastomers. The stretching of the elastomers enables them to 'gain elastic strain energy' and is, therefore, considered to be the theoretical limit of possible electrical energy conversion for the dielectric elastomer generator/actuator spokes. Additionally, the elastomer material properties of the spokes were altered to simulate the actuation of those same elastomers; with overall strain energy being subsequently investigated. Ultimately this is a preliminary study exploring the ability of such smart materials - electricity-generating and self-actuating elastomers - to actively adapt an ocean wave energy converter's structure to address and overcome the aforementioned challenges.

active materials↗
DOE OSTI2024

Optimized Floating Offshore Wind Turbine Substructure Design Trends for 10–30 MW Turbines in Low-, Medium-, and High-Severity Wave Environments

Floating offshore wind is a promising renewable energy source, as 60% of the wind resources globally are found at depths requiring floating technologies, it minimizes construction at sea, and provides opportunities for industrialization given a lower site dependency. While floating offshore wind has numerous advantages, a current obstacle is its cost in comparison to more established energy sources. One cost-reduction approach for floating wind is increasing turbine capacities, which minimizes the amount of foundations, moorings, cables, and O&M equipment. This work presents trends in mass-optimized VolturnUS hull designs as turbine capacity increases for various wave environments. To do this, a novel rapid hull optimization framework is presented that employs frequency domain modeling, estimations of statistical extreme responses, industry constructability requirements, and genetic algorithm optimization to generate preliminary mass-optimal VolturnUS hull designs for a given turbine design and set of site conditions. Using this framework, mass-optimized VolturnUS hull designs were generated for 10–30 MW turbines for wave environments of varying severities. These design studies show that scaling up turbine capacities increases the mass efficiency of substructure designs, with decreasing returns, throughout the examined turbine capacity range. Additionally, increased wave environment severity is shown to increase the required mass of a given substructure design.

VolturnUS↗
NASA NTRS1987

Automatic continuum analysis of reflectance spectra

A continuum algorithm based on a Segmented Upper Hull method (SUH) is described. An upper hull is performed on segments of a spectrum defined by local minima and maxima. The segments making a complete spectrum are then combined. The definition of the upper hull allows the continuum to be both concave and/or convex, adapting to the shape of the spectrum. The method performs multiple passes on a spectrum by segmenting each local maximum to minimum and performing an upper hull. The algorithm naturally adapts to the widths of absorption features, so that all features are found, including the nature of doublets, triplets, etc. The algorithm is also reasonably fast on common minicomputers so that it might be applied to the large data sets from imaging spectrometers.

Clark, Roger N.↗
DOE OSTI2024

Utilizing biochars to stabilize mercury in contaminated floodplain sediment: Implications on mercury remediation

Major weather events contribute to the mobility and remobilization of legacy mercury (Hg) contamination and sequestration within sediments. Remediation using biochar as a soil amendment is a useful technique to immobilize and decrease Hg toxicity. This study explored whether biochar application is effective at stabilizing labile mercury (LaHg) from floodplain sediment. Controlled mesocosms simulating contamination events and flooding conditions were conducted. Floodplain sediment, which experiences annual periodic flooding, was collected. Sediment was spiked with inorganic Hg, applied with different types of biochar, and experienced simulated flooding events. Four types of biochar, pure rice husk (RH), pure peanut hull (PH), sulfur-modified rice husk (SMRH), and sulfur-modified peanut hull (SMPH), were applied at 10 and 40 g/kg rates (i.e., RH 10, RH 40; PH 10, PH 40, SMRH 10, SMRH 40, SMPH 10, SMPH 40). Total Hg, methylmercury, and LaHg concentrations were analyzed by coupling with redox potential measurements. Results indicate that SMRH 10, PH 10, PH 40, SMPH 10, and SMPH 40 successfully remediate Hg by stabilizing and reducing LaHg species from floodplain sediment. However, a high Hg methylation potential was observed with unsulfated and sulfated peanut hulls (PH 10, PH 40, SMPH 10, and SMPH 40), as they tend to create a reducing microenvironment that favors sulfate reduction reactions. Additionally, sulfur-modified biochar tends to promote Hg methylation potential at high application rates (i.e., 40 g/kg). We thus recommend using SMRH at a relatively low application rate (SMRH 10) for the remediation of Hg from floodplain sediment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Machine learning guided search for energetically favorable metal borocarbide ternary compounds

In this work, we employ machine-learning (ML) combined with first principles calculations to efficiently search for the energetically favorable metal borocarbide (M-B-C) ternary compounds with M being the group 1–3 metal elements. Using a crystal graph convolutional neural network (CGCNN) ML approach followed by first-principles calculations, we predicted 47 energetically favorable stable and metastable ternary Na-B-C, Ca-B-C, and La-B-C ternary compounds with their decomposition energy (E d ) below or within 100 meV/atom from the currently known convex hulls. Phonon spectra and electronic structures of the 14 energetically favorable stable structures are also investigated by first-principles calculations. By substituting the metal atoms in the 29 energetically favorable non-equivalent template structures of Na (Ca, La)-B-C with other group 1–3 elements in the periodic table, we further obtain 22 stable structures and 52 metastable structures (E d ≤100 meV/atom with respect to the known convex hulls) for Li-B-C, K-B-C, Rb-B-C, Mg-B-C, Sr-B-C, Ba-B-C, Sc-B-C and Y-B-C ternary compounds. New convex hulls including our newly predicted stable ternary structures and the known stable structures are constructed for the M-B-C systems. The results obtained by our ML guided first-principles calculations enrich our knowledge in the structure and energy landscape of metal borocarbide ternary compounds and provide useful guidance for further experimental synthesis and discovery.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Simulation of Heavy Lift Airship dynamics over large ranges of incidence and speed

A nonlinear, multibody, six-degrees-of-freedom digital simulation has been developed to study generic Heavy Lift Airship (HLA) dynamics and control. The basic aerodynamic functions developed to model the hull, tail, and rotor loads continuously over all incidence ranges are reviewed and applied to a Quadrotor HLA with a low fineness ratio hull and a small vee-tail. Trim calculations for a test vehicle suggest control power deficiencies in crosswind stationkeeping for the unloaded vehicle. Gust responses show the importance of correctly calculating loads due to accelerated relative motion of air and hull. Numerically linearized dynamics for the test vehicle show the existence of a divergent yaw mode, and an oscillatory pitch mode whose stability characteristics are sensitive to flight speed. A considerable improvement in the vehicle's stability and response results from a simple multi-axis closed-loop control system operating on the rotors and propeller blades.

Tischler, M. B.↗
NASA NTRS1985

Theory and application of calibration techniques for an NDBC directional wave measurements buoy

The National Data Buoy Center (NDBC) of the National Oceanic and Atmospheric Administration (NOAA) deployed a 10-m-diameter discus-type hull in the Pacific Ocean some 185 km southwest of Los Angeles, CA, in April 1984. Aboard this hull was an electronic system capable of acquiring, processing, and transmitting to shore directional wave measurements. For this system to produce accurate data, a number of factors had to be taken into account. These factors included noise, amplitude and phase alterations due to mechanical and electrical components, and magnetic fields arising from the hull. Comprehensive calibration and verification techniques were developed and applied to ensure data quality. The system configuration is described with emphasis on the methods used in the data processing to correct for the various factors. Examples of the resulting corrected data are given.

Steele, K. E.↗
NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part II : Stress and Strength Determination

The tests described in this report furnished data on the actual aerodynamic forces, and the resulting stresses and bending moments in the hull of the U. S. S. "Los Angeles" during as severe still-air maneuvers as the airship would normally be subjected to, and in straight flight during as rough air as is likely to occur in service, short of squall or storm conditions. The maximum stresses were found to be within the limits provided for in accepted practice in airship design. Normal flight in rough air was shown to produce forces and stresses about twice as great as the most severe still-air maneuvers. No light was thrown upon the forces which might occur in extreme or exceptional conditions, such as the storm which destroyed the "Shenandoah". The transverse aerodynamic forces on the hull proper were found to be small and irregular. Owing to the necessity of conserving helium, it was impossible to fly the airship in a condition of large excess of buoyancy or weight in order to determine the air pressure distribution at a fixed angle of pitch. However, there is every reason to believe that in that condition the forces on the actual airship are as close to the wind-tunnel results as can be determined by present type of pressure measuring apparatus. It is considered that most important data obtained are the coefficients of tail-surface forces and hull-bending moments. These are tabulated in this report.

Burgess, C P↗
NASA NTRS1993

Multiphase complete exchange: A theoretical analysis

Complete Exchange requires each of N processors to send a unique message to each of the remaining N-1 processors. For a circuit switched hypercube with N = 2(sub d) processors, the Direct and Standard algorithms for Complete Exchange are optimal for very large and very small message sizes, respectively. For intermediate sizes, a hybrid Multiphase algorithm is better. This carries out Direct exchanges on a set of subcubes whose dimensions are a partition of the integer d. The best such algorithm for a given message size m could hitherto only be found by enumerating all partitions of d. The Multiphase algorithm is analyzed assuming a high performance communication network. It is proved that only algorithms corresponding to equipartitions of d (partitions in which the maximum and minimum elements differ by at most 1) can possibly be optimal. The run times of these algorithms plotted against m form a hull of optimality. It is proved that, although there is an exponential number of partitions, (1) the number of faces on this hull is Theta(square root of d), (2) the hull can be found in theta(square root of d) time, and (3) once it has been found, the optimal algorithm for any given m can be found in Theta(log d) time. These results provide a very fast technique for minimizing communication overhead in many important applications, such as matrix transpose, Fast Fourier transform, and ADI.

Bokhari, Shahid H.↗
NASA NTRS1976

Safer Pleasure Boats

'Flamarest' coating developed by Avco Corporation for NASA to protect fuel lines and tanks is sprayed on the interior of polyester boat hull in commercial application. About 30 mils of the coating prevented structural damage to hull during test in which a 13 minute interior gasoline fire was started. An unprotected hull would begin to burn in 30 seconds. Same material applied as tape to wrap fuel lines effectively insulates hose when charred while also reducing spread of flame.

Source record↗
NASA NTRS1948

Tank Tests of a Powered Model of a Compression Plane, NACA Model 171A-2

The compression plane is intended for operation on or close to the surface of the water, and has a hull with a concave bottom which forms the upper surface of a tunnel into which air is forced under pressure to support part of the load. The results of the tests made in Langley tank no. 1 include values of the horizontal forces, trimming moment, and static pressure in the tunnel for a wide range of loads and speeds and two power conditions, and are presented in the form of curves against speed with load as a parameter. The results are scaled up to 10 times the model size for three conditions at which the model is self-propelled at a steady speed. Lift is obtained from the static pressure of air in the tunnel. In general, the ratio of the gross load to the total resistance increases with increase in load and decrease in speed. This ratio varies between l-7 and 5.7 at high speeds and has a maximum value of 7. The total resistance is nearly the same for both power conditions except at low speeds and heavy loads. No abrupt change in forces on the hull or flow around the hull occurs in. the region of zero draft. The centers of pressure are generally far aft. At the most efficient trim (1.2'), considerable bow-up moment would be required for practicable operation. There is no abrupt transition from the air-borne to the water- borne condition.

Mottard, Elmo J.↗
NASA NTRS1978

Smooth Passage For The Jetfoil

The Flying Princess is a Boeing Jetfoil, one of a family of commercial waterjets built by Boeing Marine Systems, a division of The Boeing Company, Seattle, Washington. The new Jetfoil offers a number of advantages over earlier hydrofoils, a major one being a smooth ride in rough waters. NASA technology contributed to jolt-free passenger comfort. Hydrofoils skim the surface at speeds considerably greater than those of conventional ships because there is little friction between hull and water. Hulls are raised above the water by the lift of the foils, which resemble and function like an airplane wing. The foils are attached to the hull by rigid struts, which ordinarily cause a vessel operating in coastal seas to follow the contour of the waves. In wind-whipped waters, this makes for a rough ride. Seeking to increase passenger acceptance, Boeing Marine System engineers looked for ways to improve rough-water ride quality. Langley Research Center conducts continuing ride quality research. Initially, it was aimed at improving aircraft ride; it was later expanded to include all modes of transportation. Research includes studies of vibration, acceleration, temperature, humidity, passenger seats and posture, and the psychological aspects of passenger reaction to vehicle ride. As part of the program, Langley developed instrumentation, ride quality models and methods of data analysis.

Source record↗