Search NASA⌕ Search

SEARCH · Search NASA

Results for “IT energy efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Energy efficient engine: Flight propulsion system preliminary analysis and design

The characteristics of an advanced flight propulsion system (FPS), suitable for introduction in the late 1980's to early 1990's, was more fully defined. It was determined that all goals for efficiency, environmental considerations, and economics could be met or exceeded with the possible exception of NOx emission. In evaluating the FPS, all aspects were considered including component design, performance, weight, initial cost, maintenance cost, engine system integration (including nacelle), and aircraft integration considerations. The current FPS installed specific fuel consumption was reduced 14.2% from that of the CF6-50C reference engine. When integrated into an advanced, subsonic, study transport, the FPS produced a fuel burn savings of 15 to 23% and a direct operating cost reduction of 5 to 12% depending on the mission and study aircraft characteristics relative to the reference engine.

Johnston, R. P.↗
NASA NTRS1981

Energy efficient engine, low-pressure turbine boundary layer program

A study was conducted to investigate development of boundary layers under the influence of velocity distributions simulating the suction side of two state-of-the-art turbine airfoils: a forward loaded airfoil (squared-off design) and an aft loaded airfoil (aft-loaded design). These velocity distributions were simulated in a boundary layer wind tunnel. Detailed measurements of boundary layer mean velocity and turbulence intensity profiles were obtained for an inlet turbulence level of 2.4 percent and an exit Reynolds number of 800,000. Flush-mounted hot film probes identified the boundary layer transition regimes in the adverse pressure gradient regions for both velocity distributions. Wall intermittency data showed good agreement with the correlations of Dhawan and Narasimha for the intermittency factor distribution in transitional flow regimes.

Gardner, W. B.↗
NASA NTRS1981

Energy efficient engine, high-pressure turbine cooling model technology report

Two dimensional flow visualization model tests were used to substantiate the flow stability benefits derived from the use of turning vanes in the root and tip turn flow areas. Results indicate the need for corner fillets and flow injection into the acute corner formed by the intersection of the rib and simulated airfoil suction surface in order to minimize recirculation (stagnation) of flow in that region. Three dimensional flow visualization model tests verified the actual blade coolant passage design.

Gardner, W. B.↗
NASA NTRS1981

Aircraft energy efficiency. Overview

Six advanced technology development projects that could cut fuel consumption of future civil air transports by as much as 50 percent are highlighted. These include improved engine components; better engine design; thin short blades for turboprop aircaft; using composite primary structures for weight reduction; the use of supercritical wings, higher aspect ratio, and winglets for improved aerodynamics; active controls; and laminar flow control. The time span of each of the six efforts and NASA's expected expenditures are also discussed.

Source record↗
NASA NTRS1981

Design and development of the combustor inlet diffuser for the NASA/GE energy efficient engine

Results of an experimental investigation of the aerodynamic performance of a split duct annular combustor inlet diffuser system are presented. Several diffuser configurations were investigated in 3X-scale water table tests and the preferred design was evaluated in full-scale annular airflow model tests. Pressure recovery and flow losses were determined as a function of prediffuser inlet velocity profile, flow extraction at the prediffuser exit, and distribution of flow in the combustor. Inlet velocity profile and turbulence levels were found to have a pronounced effect on system performance. Flow extraction at the prediffuser exit was found to have little influence on system performance. Generally, the annular split duct diffuser system was found to satisfy the performance objectives for the engine.

Sabla, P. E.↗
NASA NTRS1981

Mixer nozzle aeroacoustic characteristics for the energy efficient engine

Aeroacoustic tests are conducted on scale model mixer nozzle configurations, a separate flow nozzle, and a baseline conical nozzle in an anechoic chamber free-jet facility to investigate exhaust system designs. Far-field acoustic data and exhaust jet plume aerodynamic data are obtained for various combinations of exhaust jet velocity and simulated flight speed, with corrected microphone data at a constant 12.2 m arc distance, and scaled acoustic data at a sideline distance of 457 m. It is found that jet plume aerodynamic and acoustic characteristics of lobed mixer exhaust systems are similar to those of a conical nozzle operating at the same specific thrust, although differences occur at high frequencies, where the sound pressure level of the mixer nozzle is 1-5 dB higher than that of a conical nozzle. In addition, no direct correlation is found between exit plane turbulence levels and plume development or acoustic characteristics for mixer exhaust configurations.

Gliebe, P. R.↗
NASA NTRS1982

Capacity limit of the noiseless, energy-efficient optical PPM channel

It is shown that even though the capacity per photon can be made to increase without bound, the capacity per channel use (for best power efficiency) is always less than 2 nats per symbol. Furthermore, it approaches 2 nats per symbol as the bandwidth expansion factor goes to infinity.

Lesh, J. R.↗
NASA NTRS1979

Development of a low risk augmentation system for an energy efficient transport having relaxed static stability

An augmentation system for a 230 passenger, twin engine aircraft designed with a relaxation of conventional longitudinal static stability was developed. The design criteria are established and candidate augmentation system control laws and hardware architectures are formulated and evaluated with respect to reliability, flying qualities, and flight path tracking performance. The selected systems are shown to satisfy the interpreted regulatory safety and reliability requirements while maintaining the present DC 10 (study baseline) level of maintainability and reliability for the total flight control system. The impact of certification of the relaxed static stability augmentation concept is also estimated with regard to affected federal regulations, system validation plan, and typical development/installation costs.

Sizlo, T. R.↗
NASA NTRS1979

Energy efficient engine. Flight propulsion system preliminary analysis and design

The characteristics of an advanced Flight Propulsion System (FPS) suitable for introduction in the late 1980's to early 1990's, were defined. It was determined that NASA goals for efficiency, environmental considerations, and economics could be met or exceeded with the possible exception of NOx emission. In evaluating the FPS, all aspects were considered including component design, performance, weight, initial cost, maintenance cost, engine-system integration (including nacelle), and aircraft integration considerations. In terms of the NASA goals, the current FPS installed specific fuel consumption was reduced 14.2% from that of the CF6-50C reference engine. When integrated into an advanced, subsonic, study transport, the FPS produced a fuel-burn savings of 15 to 23% and a direct operating cost reduction of 5 to 12% depending on the mission and study-aircraft characteristics relative to the reference engine.

Johnston, R. P.↗
NASA NTRS1982

Energy efficient face seal

Torque, face temperature, leakage, and wear of a flat face seal were compared with three coned face seals at pressures up to 2758 kPa and speeds up to 8000 rpm. Axial movement of the mating seal parts was recorded by a digital data acquisition system. The coning of the tungsten carbide primary ring ranged from .51 micro-m to 5.6 micro-m. The torque of the coned face seal balanced to 76.3% was an average 42% lower, the leakage eleven times higher, than that of the standard flat face seal. The reduction of the balance of the coned face seal to 51.3% resulted by decreasing the torque by an additional 44% and increasing leakage 12 to 230 times, depending on the seal shaft speed. No measurable wear was observed on the face of the coned seals.

Sehnal, J.↗
NASA NTRS1983

Capacity limit of the noiseless, energy-efficient optical PPM channel

It is shown that even though the capacity per photon can be made to increase without bound, the capacity per channel use (for best power efficiency) is always less than 2 nats per symbol. Furthermore, it approaches 2 nats per symbol as the bandwidth expansion factor goes to infinity. Previously announced in STAR as N82-20121

Lesh, J. R.↗
NASA NTRS1983

High energy efficient solid state laser sources

Slab glass performance studies demonstate 18 J of output at 2 Hz with 2.3% wall plug efficiency. The goal is to achieve 10 J per pulse at 10 Hz and 3% wall plug efficiency during the next annual period. The slab concept was extended to Nd:YAG and to Nd:GGG. To date over 80 W of CW output power at 2% efficiency was generated in slab Nd:YAG. A multiplexed slab Nd:YAG pre-amplifier was invented and a Nd:YAG oscillator was demonstrated with 100kHz linewidth for eventual use in wind velocity measurements.

Byer, R. L.↗
NASA NTRS1984

Effects of aircraft and flight parameters on energy-efficient profile descents in time-based metered traffic

Concepts to save fuel while preserving airport capacity by combining time based metering with profile descent procedures were developed. A computer algorithm is developed to provide the flight crew with the information needed to fly from an entry fix to a metering fix and arrive there at a predetermined time, altitude, and airspeed. The flight from the metering fix to an aim point near the airport was calculated. The flight path is divided into several descent and deceleration segments. Descents are performed at constant Mach numbers or calibrated airspeed, whereas decelerations occur at constant altitude. The time and distance associated with each segment are calculated from point mass equations of motion for a clean configuration with idle thrust. Wind and nonstandard atmospheric properties have a large effect on the flight path. It is found that uncertainty in the descent Mach number has a large effect on the predicted flight time. Of the possible combinations of Mach number and calibrated airspeed for a descent, only small changes were observed in the fuel consumed.

Dejarnette, F. R.↗
NASA NTRS1982

Configuration design studies and wind tunnel tests of an energy efficient transport with a high-aspect-ratio supercritical wing

The results of design studies and wind tunnel tests of high aspect ratio supercritical wings suitable for a medium range, narrow body transport aircraft flying near M=0.80 were presented. The basic characteristics of the wing design were derived from system studies of advanced transport aircraft where detailed structural and aerodynamic tradeoffs were used to determine the most optimum design from the standpoint of fuel usage and direct operating cost. These basic characteristics included wing area, aspect ratio, average thickness, and sweep. The detailed wing design was accomplished through application of previous test results and advanced computational transonic flow procedures. In addition to the basic wing/body development, considerable attention was directed to nacelle/plyon location effects, horizontal tail effects, and boundary layer transition effects. Results of these tests showed that the basic cruise performance objectives were met or exceeded.

Henne, P. A.↗
NASA NTRS1980

Results of design studies and wind tunnel tests of high-aspect-ratio supercritical wings for an energy efficient transport

These basic characteristics of critical wings included wing area, aspect ratio, average thickness, and sweep as well as practical constraints on the planform and thickness near the wing root to allow for the landing gear. Within these constraints, a large matrix of wing designs was studied with spanwise variations in the types of airfoils and distribution of lift as well as some small planform changes. The criteria by which the five candidate wings were chosen for testing were the cruise and buffet characteristics in the transonic regime and the compatibility of the design with low speed (high-lift) requirements. Five wing-wide-body configurations were tested in the NASA Ames 11-foot transonic wind tunnel. Nacelles and pylons, flap support fairings, tail surfaces, and an outboard aileron were also tested on selected configurations.

Steckel, D. K.↗
NASA NTRS1984

Comparison of measured and calculated airloads on an energy efficient transport wing model equipped with oscillating control surfaces

Wind-tunnel measurements of steady and unsteady pressures for a high-aspect-ratio supercritical wing model are compared with calculations by the linear unsteady aerodynamic lifting-surface theory, known as the Doublet Lattice method, at Mach numbers of 0.650 (subsonic) and 0.78 (transonic). The steady-pressure data comparisons are made for incremental changes in angle of attack and control-surface deflection. The unsteady-pressure data comparisons are made for oscillating control-surface deflections. Some differences between the measured and calculated aerodynamics are attributed to viscous and transonic effects that are not accounted for in the Doublet Lattice analysis. Comparisons of the transonic unsteady-pressure data for the oscillating control surfaces are improved by applying empirical corrections based on the steady-pressure measurements to the unsteady Doublet Lattice calculations.

Mccain, W. E.↗