Search NASA⌕ Search

SEARCH · Search NASA

Results for “Impurity diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Simulation of the SPARC plasma boundary with the UEDGE code

Here in this work, the UEDGE edge transport code is used to examine conditions in the SPARC divertor and edge plasma for various levels of carbon impurity and power from the core (P SOL ). A double-null magnetic configuration is simulated assuming up-down symmetry in geometry and physics. The anomalous heat and particle transport coefficients are tuned to match empirical predictions for SPARC's midplane density profiles, target plate heat flux profiles, and inner/outer divertor power sharing. Convective transport is included on the low-field side, while on the high-field side the transport is modeled as purely diffusive. Hydrogen neutrals are modeled as a fluid with inertial effects, and a carbon impurity is included using the fixed-fraction model. We find that detachment induced by impurity seeding could significantly reduce the heat flux to the divertor surfaces in the SPARC tokamak. At P SOL = 28 MW (the value predicted for SPARC's full-power H-mode scenario) cases with both divertor legs detached were obtained with a carbon impurity fraction between 0.3%–1.4%, far below Z eff limits for SPARC. When the plasma in the outer leg is detached, the peak heat flux density perpendicular to the target plate is below 1 MW m -2 , electron and ion temperatures are less than 1.5 eV, and momentum detachment is observed. However, the detachment state is found to be sensitive to the side-wall boundary conditions, the level of neutral pumping, and the target plate tilt. Finally, a broadly similar SOLPS simulation of SPARC is used to assess the appropriateness of the simpler impurity and neutral models used in UEDGE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1981

EBIC/TEM investigations of process-induced defects in EFG silicon ribbon

Electron bombardment induced conductivity and scanning transmission electron microscopy observations on unprocessed and processed edge-defined film-fed growth ribbon show that the phosphorus diffused junction depth is not uniform, and that a variety of chemical impurities precipitate out during processing. Two kinds of precipitates are found (1) 10 nm or less in size, located at the dislocation nodes in sub-boundary like dislocation arrangements formed during processing and (2) large precipitates, the chemical composition of which has been partially identified. These large precipitates emit dense dislocations tangles into the adjacent crystal volume.

Cunningham, B.↗
NASA NTRS1993

A method of making a single layer multi-color luminescent display

The invention is a method of forming a multi-color luminescent display including the steps of depositing on an insulator substrate a smooth single layer of host material which itself may be a phosphor with the properties to host varying quantities of different impurities and introducing one or more of said different impurities into selected areas of the single layer of host material via an appropriately positioned mask as by thermal diffusion or ion-implantation to form a pattern of phosphors of different colors in the single layer of host material such that the top surface of the host layer remains smooth. Red phosphors are formed by adding impurities selected from the group consisting of Sm, SmF3, Eu, EuF3, and ZnS:MnTbF3 to a ZnS host; green phosphors by adding impurities selected from the group consisting of Tb and TbF3 to a ZnS host; and blue phosphors by adding impurities selected from the group consisting of Tm, Al, Ag, and Mg to a ZnS host.

Robertson, James B.↗
DOE OSTI2020

Reducing dielectric loss and enhancing electrical insulation for multilayer polymer films by nanoconfined ion transport under high poling electric fields

High temperature polar polymers have demonstrated potential for good thermal stability and high dielectric constant at the same time. However, polarization of contaminated impurity ions in polar polymers, even at the ppm level, can significantly increase the dielectric loss at high temperature and low frequencies. One effective strategy to mitigate this problem is to multilayer them with a high temperature nonpolar dielectric polymer to confine impurity ion transport at the nanometer scale. In this study, confined ion transport in high temperature polycarbonate (HTPC)/poly(vinylidene fluoride) (PVDF) multilayer films under high AC electric fields was studied using a direct analytical simulation method. Different from the ion transport under low fields, the ion diffusion model failed to describe the ion transport under high electric fields. An exponential ion distribution profile, which was observed for the DC poling situation, was employed to implement the direct analytical simulation. Confined impurity ion transport under high AC fields was quantitatively understood. As the AC field increased, the mobile ion concentration decreased whereas the diffusion coefficient increased. The decrease of mobile ion concentration was explained by the blockage of impurity ions by the HTPC layers. This knowledge helped in the determination of optimal conditions to polarize impurity ions from the PVDF layers into the HTPC layers. After cooling below the glass transition temperature of HTPC, polarized impurity ions were locked inside the HTPC layers. As a result, increased discharge efficiency and enhanced electrical insulation (i.e., increased dielectric breakdown strength) were achieved for the polarized multilayer films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation of plasma transport in MPS-LD linear plasma device by using BOUT++

Here a linear plasma device (LPD) module based on the 2D transport module under the BOUT++ framework is developed in this paper to simulate plasma transport in the LPD. The LPD module includes three parts, i.e. magnetic field calculation, simulation mesh generation and plasma transport setup. The magnetic field is calculated with the circular current loop using the location and current information of each coil. The mesh generation code can produce a simulation mesh for LPD by employing the magnetic field. The plasma transport model is based on the reduced Braginskii equations, which consist of the continuity equation, momentum equation, and energy equation. The fluid neutral model is applied for neutral particle simulation. Deuterium (D) and helium (He) ions and atoms can be simulated by the model. The first attempt to simulate plasma transport in the new LPD, called multiple plasma simulation linear plasma device (MPS-LD), is presented using the developed model. The D plasma transport in the MPS-LD is simulated and benchmarked against the two-point model, showing the validation of the BOUT++ simulation. The effects of radial transport on the heat load to the target are studied, which illustrates the significant impact of the radial diffusivities $D_⟂$ and $\mathcal{X}_{⟂i,e}$ on the plasma. Moreover, the He impurity injection process during the discharge is studied with emphasis on plasma–impurity interactions. The simulation results show that He injection can reduce the plasma energy load to the target significantly, and the efficiency depends on the He source density and injection velocity. The present work provides an alternative and flexible simulation tool for plasma transport in LPDs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1986

Process-induced defects in solar cell silicon

The microstructure of as-grown and processed, edge-defined film-fed grown, silicon ribbons was studied in order to identify the basic mechanisms responsible for the change of the as-grown defect structure during processing at elevated temperatures. The short heat treatment required to diffuse the p-n junction was sufficient to cause heterogeneous precipitation of impurity atoms, particularly transition metals. In addition, an elastic recovery of the ribbon occurred by dislocation glide, resulting in the formation of a polygonizationlike structure of subboundaries in the base. Mechanisms are suggested by which twin boundaries, acting as dislocation obstacles, can concentrate the relatively low average dislocation densities typical of edge-defined film-fed grown ribbons (10 to the 4th to 10 to the 8th/sq cm) to values which are sufficient to induce the formation of subgrainlike boundary structures.

Gleichmann, R.↗
NASA NTRS2003

Protein crystals and their growth

Recent results on the associations between protein molecules in crystal lattices, crystal-solution surface energy, elastic properties, strength, and spontaneous crystal cracking are reviewed and discussed. In addition, some basic approaches to understanding the solubility of proteins are followed by an overview of crystal nucleation and growth. It is argued that variability of mixing in batch crystallization may be a source of the variation in the number of crystals ultimately appearing in the sample. The frequency at which new molecules join a crystal lattice is measured by the kinetic coefficient and is related to the observed crystal growth rate. Numerical criteria used to discriminate diffusion- and kinetic-limited growth are discussed on this basis. Finally, the creation of defects is discussed with an emphasis on the role of impurities and convection on macromolecular crystal perfection.

Review↗
NASA NTRS2000

Direct Visualization of an Impurity Depletion Zone

When a crystal incorporates more impurity per unit of its volume than the impurity concentration in solution, the solution in vicinity of the growing crystal is depleted with respect to the impurity I,2. With a stagnant solution, e. g. in microgravity or gels, an impurity depletion zone expands as the crystal grows and results in greater purity in most of the outer portion of the crystal than in the core. Crystallization in gel provides an opportunity to mimic microgravity conditions and visualize the impurity depletion zone. Colorless, transparent apoferritin (M congruent to 450 KDa) crystals were grown in the presence of red holoferritin dimer as a microheterogeneous impurity (M congruent to 900 KDa) within agarose gel by counterdiffusion with Cd(2+) precipitant. Preferential trapping of dimers, (distribution coefficient K = 4 (exp 1,2)) results in weaker red color around the crystals grown in the left tube in the figure as compared to the control middle tube without crystals. The left and the middle tubes contain colored ferritin dimers, the right tube contains colored trimers. The meniscus in the left tube separate gel (below) and liquid solution containing Cd(2+) (above). Similar solutions, though without precipitants, were present on top of the middle and right tube allowing diffusion of dimers and trimers. The area of weaker color intensity around crystals directly demonstrates overlapped impurity depletion zones.

Chernov, Alex A.↗
NASA NTRS1971

Lithium - An impurity of interest in radiation effects of silicon.

Study of the introduction and annealing of defects produced in lithium-diffused float-zone n-type silicon by 30-MeV electrons and fission neutrons. The introduction rate of recombination centers produced by electron irradiation is dependent on lithium concentration and for neutron irradiation is independent of lithium concentration. The introduction rate of Si-B1 centers also depends on the lithium concentration. The annealing of electron- and neutron-produced recombination centers, Si-B1 centers, and Si-G7 centers in lithium-diffused silicon occurs at much lower temperatures than in nondiffused material.

Naber, J. A.↗
NASA NTRS1984

Remarks on a vibronic origin for the diffuse band spectrum

It has been demonstrated that the diffuse band spectrum could not originate as a series of vibronic transitions from atomic impurities in interstellar MgO grains as has recently been proposed since laboratory spectra of such materials show no evidence for such complex structure. Furthermore, recent observational evidence indicates that the extinction feature at 160 nm in the standard interstellar extinction curve upon which the identification of interstellar MgO was founded is actually the result of a calibration error in the original observational data.

Nuth, J. A.↗
NASA NTRS1992

Single layer multi-color luminescent display and method of making

The invention is a multi-color luminescent display comprising an insulator substrate and a single layer of host material, which may be a phosphor deposited thereon that hosts one or more different impurities, therein forming a pattern of selected and distinctly colored phosphors such as blue, green, and red phosphors in a single layer of host material. Transparent electrical conductor means may be provided for subjecting selected portions of the pattern of colored phosphors to an electric field, thereby forming a multi-color, single layer electroluminescent display. A method of forming a multi-color luminescent display includes the steps of depositing on an insulator substrate a single layer of host material, which itself may be a phosphor, with the properties to host varying quantities of different impurities and introducing one or more of said different impurities into selected areas of the said single layer of host material by thermal diffusion or ion implantation to form a pattern of phosphors of different colors in the said single layer of host material.

Robertson, James B.↗
DOE OSTI2024

First-Principles Studies of Tritium Species Diffusivity Across the Interface of Nickel-Plated Zircaloy-4

In this study, we will calculate the 3H2 and 3H2O diffusion mechanism in the Ni coated layer and the dominant 3H species dissolution into the Zircaloy-4 getter. We will optimize the Ni/Zr interface and introduce Sn and O impurities. To achieve the objectives, we will perform the investigation by using spin-polarized density functional theory (DFT) methods to capture the effects of Ni magnetic properties on 3H diffusion. We will introduce NiO/Ni(OH) on the Ni side closer to the interface. Then, the 3H diffusion pathways and barriers from Ni side to the zircalory-4 will be explored. We will investigate how NiO/Ni(OH) affects the 3H diffusion across the interface.

Paudel, Hari P.↗
NASA NTRS1993

Ultraviolet stability and contamination analysis of Spectralon diffuse reflectance material

A detailed chemical analysis was carried out on Spectralon, a highly Lambertian, diffuse reflectance material. Results of this investigation unambiguously identified the presence of an organic (hydrocarbon) impurity intrinsic to the commercial material. This impurity could be removed by a vacuum bake-out procedure and was identified as the cause of optical changes (degradation) that occur in the material when exposed to UV light. It was found that when this impurity was removed, the Spectralon material was photochemically stable and maintained its reflectance properties even after extensive solar UV exposure.

Stiegman, Albert E.↗
DOE OSTI2020

Analysis of the Impurity MgOHCl in Molten Chloride Salts Toward its Electrochemical Removal from CSP Plants During Operation

The work presented here is a study of the impurity MgOHCl in molten chloride salts, toward the eventual goal of electrochemically removing it from operational molten-chloride-based concentrating solar power (CSP) plants.1,2 Implementation of molten chloride salts as a heat transfer fluid is among the most promising pathways for decreasing the levelized cost of energy (LCOE) of CSP systems because its high thermal stability allows higher operating temperatures, and thus, greater efficiency. However, this impurity - formed when MgCl2 salts are exposed to air and moisture - cause significant corrosion of containment alloys.1 Therefore, we have developed and validated in a laboratory setting: 1) a method for the formation of MgOHCl for controlled impurity spike in molten salt for its further sensing, evaluation, and reduction; 2) evaluated its diffusion in the molten salt, and 3) began assessing its electrochemical properties. Our findings allow us to propose solutions for efficiently and instantly removing MgOHCl from an operational CSP plant.

concentrated solar power↗
DOE OSTI2026

Electrochemical behavior of SnCl 2 and influence of Cu and Ni ions in molten LiCl−KCl−CaCl 2 eutectic

Reliable transport and thermodynamic data for multivalent ions in complex molten salts are scarce, limiting model fidelity for electrorefining and impurity control. Here, we report a comprehensive electrochemical characterization of SnCl₂ in LiCl–KCl–CaCl₂ (50.5–44.2–5.3 mol%) at 685 K, including the effects of Ni 2+ and Cu + impurities. Using cyclic voltammetry (CV), chronoamperometry (CA), and chronopotentiometry (CP), we quantified Sn 2+ and Ni 2+ diffusion with exceptional agreement across methods: Sn 2+ averaged (1.03 ± 0.10) × 10 −5 cm 2 s −1 , and Ni 2+ averaged (0.75 ± 0.19) × 10 −5 cm 2 s −1 . The tight confidence-interval overlap across CV, CA, and CP strengthens confidence in these values and is uncommon in molten chloride studies. Open-circuit-potential measurements provided standard apparent reduction potentials that closely match LiCl–KCl literature, indicating minimal shift with CaCl₂ present. The Sn 2+ /Sn couple behaves as a reversible two-electron soluble–insoluble process at 685 K; the Sn 4+ /Sn 2+ couple transitions to soluble–soluble behavior near 788 K, which may correlate with the decomposition of surface bound chlorostannates, though direct characterization remains to be established. In mixed systems, Cu+/Cu overlaps Sn 2+ /Sn, limiting Cusingle bondSn electroseparation, whereas the larger potential gap between Ni 2+ /Ni and Sn 2+ /Sn supports selective Ni removal. These internally consistent transport and thermodynamic data establish a validated basis for process modeling and optimization of Sn electrorefining and impurity management in LiCl–KCl–CaCl₂.

Berzins-Delahay↗
DOE OSTI2024

First-Principles Studies of Tritium Species Diffusivity Across the Interface of Nickel-Plated Zircaloy-4

α-Zr and its alloys are known as best 3 H getters due to their excellent corrosion resistance under chemically corrosive environment, low thermal neutron absorption cross-section and robust mechanical strength at high temperature. In this work, we conducted a systematic study on constructing and optimizing Ni and Zr surfaces, interfacing the stable Ni and Zr surfaces to create an optimal Ni-Zr interface, and an understanding the diffusion mechanisms for 3 H across Ni(111)-Zr(0001) interface with and without vacancies and impurities such as Sn and O.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2002

Surface Processes of Faceted Growth

Atomic force microscopy and high precision optical interferometry allow to analyze the processes that are in the core of our present understanding of faceted crystal growth. Some of these processes will be reviewed. Recent experiments suggest that the Gibbs-Thomson Law (GTL) may not be applicable to the weakly fluctuating strongly polygonized steps, with low kink density. Propagation rate of a straight short step segment changes with the segment length much steeper than predicted by GTL. If the step fluctuations are still well developed, the typical transition length may be determined just by the radius of rounded comers of the polygonized step. If fluctuations do not have enough time to develop, the kinetic effects may be essential. Indeed, 'communications' between comers of a short straight step segment may occur and, thus, the GTL may be implemented only via kink exchange. E.g., dissolutions of this short segment at macroscopic equilibrium occurs as follows: The kinks are split from one comer as a result of fluctuations, and annihilate with kinks of the opposite sign generated by another comer. Similarly, an exchange via chain of kinks on a rough step is the mechanism to implement the GT Law. If there is a supersaturation with respect to a large crystal, the kinks not only diffuse along the step, but move back the generating comers. This 'wind' prevents communication between the comers and places upper limit supersaturation only below which GTL is applicable. Steps replace kinks in the 3D case, though, of course, another dimensionality brings about another physics. Another specific problem to think about is if fluctuations are always fast enough to provide enough kinks for linear dependence of step rate on supersaturation. Increasing azimuthal polygonization of growth hillocks is a sign of insufficient fluctuation rate. Morphological stability of vicinal faces is usually considered on the basis of mutually parallel steps. Azimuthal anisotropy and interlacing of step bunches inducing the well known bunch splitting is another challenge. Among other challenging problems are: existence of surface diffusion on the crystal/so1ution interface, step interaction in solutions, achievement of step flow modes from liquids, impurity effects. New phenomena essential in biomacromolecular crystallization is another interesting area.

Chernov, A.↗