Evaluation of Vegetation Bias in InSAR Time Series for Agricultural Areas Within the San Joaquin Valley, CA
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Abstract not provided
Abstract not provided.
Abstract not provided.
Abstract not provided.
Seismic signals from 1993 show a series of magnitude (Mw) 3.7 or less seismic events in Rock Valley on the Nevada National Security Site (NNSS). Historic synthetic aperture radar images of that location were found that could provide interferometric synthetic aperture radar (InSAR) measures of the ground height during 1993. Given this historic SAR imagery, we explore answering the question if ground movement from the 1993 Rock Valley earthquake activity could be sensed by remote sensing means. Finding earthquake surface movement would assist in locating the Rock Valley fault and the 1993 earthquake hypocenter where the Source Physics Experiment Phase III series of experiments will be conducted. In this report, we show that InSAR can sense very small height differences, and for the European Radar Satellite-1 InSAR collections during 1992 and 1993 over Rock Valley earth surface movements were measured with 8 mm uplift and 12.5 mm subsidence over isolated areas. One of these earth movement areas coincides with an InSAR image pair coherence drop between March 5, 1993 and June 18, 1993. The coherence drop is over an approximately 13 square km area south southeast of Skull Mountain centered at 36° 43' 30" N latitude and 116° 05' 00" W longitude. Measured small surface movement and a loss of InSAR coherence may be caused by the series of earthquakes. The location of these InSAR detections may also coincide with water drainage or erosion displacement. There are no records to disambiguate the earthquake and erosion earth surface motion possibilities. Therefore, the InSAR findings of earth surface movement by InSAR are inconclusive.
Drawing from recently submitted work, this paper first gives a heuristic description of the sensitivity of interferometric synthetic aperture radar (INSAR) to vertical vegetation distribution and under laying surface topography. A parameter estimation scenario is then described in which the INSAR cross correlation amplitude and phase are the observations from which vegetation and surface topographic parameters are estimated. It is shown that, even in the homogeneous layer model of the vegetation, the number of parameters needed to describe the vegetation and underlying topography exceeds the number of INSAR observations for single baseline, single frequency, single incidence-angle, single polarization INSAR. Using ancillary ground truth data to compensate for the under determination of the parameters, forest depths are estimated from the INSAR data. A recently analyzed multi-baseline data set is also discussed and the potential for stand alone INSAR parameter estimation is assessed. The potential of combining the information content of INSAR with that of infrared/optical remote sensing data is briefly discussed.
The possibility of global, three-dimensional remote sensing of forest structure with interferometric synthetic aperture radar (InSAR) bears on important forest ecological processes, particularly the carbon cycle. InSAR supplements two-dimensional remote sensing with information in the vertical dimension. Its strengths in potential for global coverage complement those of lidar (light detecting and ranging), which has the potential for high-accuracy vertical profiles over small areas. InSAR derives its sensitivity to forest vertical structure from the differences in signals received by two, spatially separate radar receivers. Estimation of parameters describing vertical structure requires multiple-polarization, multiple-frequency, or multiple-baseline InSAR. Combining InSAR with complementary remote sensing techniques, such as hyperspectral optical imaging and lidar, can enhance vertical-structure estimates and consequent biophysical quantities of importance to ecologists, such as biomass. Future InSAR experiments will supplement recent airborne and spaceborne demonstrations, and together with inputs from ecologists regarding structure, they will suggest designs for future spaceborne strategies for measuring global vegetation structure.
Many clandestine development and production activities can be conducted underground to evade surveillance. The purpose of the study reported here was to develop a technique to detect underground facilities by broad-area search and then to characterize the facilities by inversion of the collected data. This would enable constraints to be placed on the types of activities that would be feasible at each underground site, providing a basis the design of targeted surveillance and analysis for more complete characterization. Excavation of underground cavities causes deformation in the host material and overburden that produces displacements at the ground surface. Such displacements are often measurable by a variety of surveying or geodetic techniques. One measurement technique, Interferometric Synthetic Aperture Radar (InSAR), uses data from satellite-borne (or airborne) synthetic aperture radars (SARs) and so is ideal for detecting and measuring surface displacements in denied access regions. Depending on the radar frequency and the acquisition mode and the surface conditions, displacement maps derived from SAR interferograms can provide millimeter- to centimeter-level measurement accuracy on regional and local scales at spatial resolution of {approx}1-10 m. Relatively low-resolution ({approx}20 m, say) maps covering large regions can be used for broad-area detection, while finer resolutions ({approx}1 m) can be used to image details of displacement fields over targeted small areas. Surface displacements are generally expected to be largest during or a relatively short time after active excavation, but, depending on the material properties, measurable displacement may continue at a decreasing rate for a considerable time after completion. For a given excavated volume in a given geological setting, the amplitude of the surface displacements decreases as the depth of excavation increases, while the area of the discernable displacement pattern increases. Therefore, the ability to detect evidence for an underground facility using InSAR depends on the displacement sensitivity and spatial resolution of the interferogram, as well as on the size and depth of the facility and the time since its completion. The methodology development described in this report focuses on the exploitation of synthetic aperture radar data that are available commercially from a number of satellite missions. Development of the method involves three components: (1) Evaluation of the capability of InSAR to detect and characterize underground facilities ; (2) inversion of InSAR data to infer the location, depth, shape and volume of a subsurface facility; and (3) evaluation and selection of suitable geomechanical forward models to use in the inversion. We adapted LLNL's general-purpose Bayesian Markov Chain-Monte Carlo procedure, the 'Stochastic Engine' (SE), to carry out inversions to characterize subsurface void geometries. The SE performs forward simulations for a large number of trial source models to identify the set of models that are consistent with the observations and prior constraints. The inverse solution produced by this kind of stochastic method is a posterior probability density function (pdf) over alternative models, which forms an appropriate input to risk-based decision analyses to evaluate subsequent response strategies. One major advantage of a stochastic inversion approach is its ability to deal with complex, non-linear forward models employing empirical, analytical or numerical methods. However, while a geomechanical model must incorporate adequate physics to enable sufficiently accurate prediction of surface displacements, it must also be computationally fast enough to render the large number of forward realizations needed in stochastic inversion feasible. This latter requirement prompted us first to investigate computationally efficient empirical relations and closed-form analytical solutions. However, our evaluation revealed severe limitations in the ability of existing empirical and analytical forms to predict deformations from underground cavities with an accuracy consistent with the potential resolution and precision of InSAR data. We followed two approaches to overcoming these limitations. The first was to develop a new analytical solution for a 3D cavity excavated in an elastic half-space. The second was to adapt a fast parallelized finite element method to the SE and evaluate the feasibility of using in the stochastic inversion. To date we have demonstrated the ability of InSAR to detect underground facilities and measure the associated surface displacements by mapping surface deformations that track the excavation of the Los Angeles Metro system. The Stochastic Engine implementation has been completed and undergone functional testing.
A report discusses Ka-band (35-GHz) radar for mapping the surface topography of glaciers and ice sheets at high spatial resolution and high vertical accuracy, independent of cloud cover, with a swath-width of 70 km. The system is a single- pass, single-platform interferometric synthetic aperture radar (InSAR) with an 8-mm wavelength, which minimizes snow penetration while remaining relatively impervious to atmospheric attenuation. As exhibited by the lower frequency SRTM (Shuttle Radar Topography Mission) AirSAR and GeoSAR systems, an InSAR measures topography using two antennas separated by a baseline in the cross-track direction, to view the same region on the ground. The interferometric combination of data received allows the system to resolve the pathlength difference from the illuminated area to the antennas to a fraction of a wavelength. From the interferometric phase, the height of the target area can be estimated. This means an InSAR system is capable of providing not only the position of each image point in along-track and slant range as with a traditional SAR but also the height of that point through interferometry. Although the evolution of InSAR to a millimeter-wave center frequency maximizes the interferometric accuracy from a given baseline length, the high frequency also creates a fundamental problem of swath coverage versus signal-to-noise ratio. While the length of SAR antennas is typically fixed by mass and stowage or deployment constraints, the width is constrained by the desired illuminated swath width. As the across-track beam width which sets the swath size is proportional to the wavelength, a fixed swath size equates to a smaller antenna as the frequency is increased. This loss of antenna size reduces the two-way antenna gain to the second power, drastically reducing the signal-to-noise ratio of the SAR system. This fundamental constraint of high-frequency SAR systems is addressed by applying digital beam-forming (DBF) techniques to synthesize multiple simultaneous receive beams in elevation while maintaining a broad transmit illumination. Through this technique, a high antenna gain on receive is preserved, thereby reducing the required transmit power and thus enabling high-frequency SARs and high-precision InSAR from a single spacecraft.
Here we present a study on geophysical inverse modelling for subsurface structural properties of an unconventional hydrocarbon site that was monitored previously by Interferometric Synthetic Aperture Radar (InSAR) technology for surface deformation. A static three-dimensional geomodel along with extracted property maps replicates the depth of each underlying stratigraphic unit and structural feature with the density of each geological layer. We examine the hypothesis that integration of elastic properties of each formation layer with InSAR observations in a stratified elastic medium will lead to a viscoelastic geophysical inverse problem that can be solved to estimate fractional volume change at the reservoir level. Moreover, we examine synthetic scenarios in which the elastic properties of the formations are perturbed before determining the resulting impact on the rate of surface deformation. The results show that although the slope of underlying formations, their density and depth can define the extent and pattern of a deformation signal, their properties have a marginal impact on volumetric change compared to the dense network of shallow depth Coal Seam Gas (CSG) mining wells. Besides, it is also demonstrated that the inversion of InSAR deformation maps can resolve the uncertainties associated with low-resolution seismic interpretation as well as filling the data gaps within seismic acquisitions. A significant contribution of this investigation to the geological basin modelling involves a) introducing a remote and non-invasive technology such as InSAR to improve geophysical mapping of subsurface structures such as faults in areas with sparse or no reflective seismic information, and b) applying a multi-layer viscoelastic geophysical source model for an unconventional hydrocarbon reservoir such as CSG.
TanDEM-X (TDX) enables to generate an interferometric coherence without temporal decorrelation effect that is the most critical factor for a successful Pol-InSAR inversion, as have recently been used for forest parameter retrieval. This paper presents mangrove forest height estimation only using single-pass/single-baseline/dual-polarization TDX data by means of new dual-Pol-InSAR inversion technique. To overcome a lack of one polarization in a conventional Pol- InSAR inversion (i.e. an underdetermined problem), the ground phase in the Pol-InSAR model is directly estimated from TDX interferograms assuming flat underlying topography in mangrove forest. The inversion result is validated against lidar measurement data (NASA's G-LiHT data).
Space-based and airplane-based synthetic aperture RADAR (SAR) can monitor ground height using interferometric SAR (InSAR) collections. However, fielding the airplane-based SAR is expensive and coordinating the frequency and timing of ground experiments with space-based SAR is challenging. This research explored the possibility of using a small, mobile unmanned aerial vehicle- base (UAV) SAR to see if it could provide a quick and inexpensive InSAR option for the Source Physics Experiment (SPE) Phase III project. Firstly, a local feasibility collection using a UAV-based SAR showed that InSAR products and height measurements were possible, but that in-scene fiducials were needed to assist in digital elevation model (DEM) construction. Secondly, an InSAR collection was planned and executed over the SPE Phase III site using the same platform configuration. We found that the image formation by the SAR manufacturer creates discontinuities, and that noise impacted the generation and accuracy of height maps. These processing artifacts need to be overcome to generate an accurate height map.
The use of lidars and radars to measure forest structure attributes such as height and biomass are being considered for future Earth Observation missions. Large footprint lidar makes a direct measurement of the heights of scatterers in the illuminated footprint and can yield information about the vertical profile of the canopy. Synthetic Aperture Radar (SAR) is known to sense the canopy volume, especially at longer wavelengths and is useful for estimating biomass. Interferometric SAR (InSAR) has been shown to yield forest canopy height information. For example, the height of scattering phase retrieved from InSAR data is considered to be correlated with the three height and the spatial structure of the forest stand. There is much interest in exploiting these technologies separately and together to get important information for carbon cycle and ecosystem science. More detailed information of the electromagnetic radiation interactions within forest canopies is needed. And backscattering models can be of much utility here. As part of a NASA funded project to explore data fusion, a three-dimensional (3D) coherent radar backscattering model and a 3D lidar backscatter models were used to investigate the use of large footprint lidar, SAR and InSAR for characterizing realistic forest scenes. For this paper, we use stem maps and other forest measurements to develop a realistic spatial structure of a spruce-hemlock forest canopy found in Maine, USA. The radar and lidar models used measurements of the 3D forest scene as input and simulated the coherent radar backscattering signature and 1064nm energy backscatter, respectively. The relationships of backscatter derived forest structure were compared with field measurements. In addition, we also had detailed airborne lidar (Laser Imaging Vegetation Sensor, LVIS) data available over the stem map sites that was used to study the accuracies of tree height derived from modeled SAR backscatter and the scattering phase center retrieved from the simulated InSAR data will be compared with the height indices, or other structure parameters derived from the lidar data. These results will address the possible synergies between lidar and radar in data in terms of forest structural information.
Different flavors of GPS time series analysis at JPL - Use same GPS Precise Point Positioning Analysis raw time series - Variations in time series analysis/post-processing driven by different users. center dot JPL Global Time Series/Velocities - researchers studying reference frame, combining with VLBI/SLR/DORIS center dot JPL/SOPAC Combined Time Series/Velocities - crustal deformation for tectonic, volcanic, ground water studies center dot ARIA Time Series/Coseismic Data Products - Hazard monitoring and response focused center dot ARIA data system designed to integrate GPS and InSAR - GPS tropospheric delay used for correcting InSAR - Caltech's GIANT time series analysis uses GPS to correct orbital errors in InSAR - Zhen Liu's talking tomorrow on InSAR Time Series analysis
We generated a large-scale mangrove forest height map using multiple TanDEM-X (TDX) interferometric synthetic aperture radar (InSAR) acquisitions with various spatial baselines in order to improve the height estimation accuracy across a wide range of forest heights. The forest height inversion using InSAR data is strongly dependent upon the vertical wavenumber (i.e., perpendicular baseline). First, we investigated the role of the vertical wavenumber in forest height inversion from InSAR data using the sensitivity of the interferometric (volume) coherence to forest height. We used corrected but lower resolution and accuracy Shuttle Radar Topography Mission (SRTM) mangrove height maps as a priori information over Akanda and Pongara National Parks in Gabon to estimate lower and upper boundaries of the vertical wavenumber over test sites from the measured coherence-to-height sensitivity. Only TDX acquisitions within the boundaries of the vertical wavenumber were selected and combined for multibaseline mangrove height inversion. Mangrove forest height was obtained with multibaseline TDX acquisitions and was validated against the reference height derived from field measurement data providing improvements in multibaseline inversion over existing height estimates (i.e., SRTM height) and single-baseline inversions (multibaseline inversion: r(exp 2) = 0.98, root mean square error (RMSE) of 2.73 m; SRTM height: r(exp 2) = 0.86, RMSE = 7.21 m; single-baseline inversions: r(exp 2) = 0.08-0.97, RMSE = 3.86-11.10 m). As a result, to accurately estimate forest heights over a wide range (3-60 m), multibaseline InSAR acquisitions (at least three different baselines) are needed to exclude biases associated with the vertical wavenumber in forest height inversion.
Spaceborne SAR interferometry (InSAR) has the potential of mapping the forest height on a global scale and a monthly/weekly basis under all weather conditions, which can improve our understanding of the global carbon dynamics. In previous work, repeatpass SAR interferometry from spaceborne sensors is utilized to create large-scale forest height maps (that are particularly interested for large-scale ecological research) based on a newly developed approach. This paper thus serves as a summary paper and also sheds light on the future directions with improved results. In particular, it will be shown that repeat-pass SAR interferometry is able to create a large-scale forest height mosaic product with RMSE 4 m for forest stands on the order of 20 hectares through using the past spaceborne repeat-pass InSAR observations (i.e. JAXA’s ALOS-1 and ALOS-2) combined with sparse airborne lidar training samples over the forested areas in New England, US. Moreover, the results and performance of this approach can be remarkably improved with several enhancement techniques that can be easily satisfied with use of future spaceborne repeat-pass InSAR and lidar missions (e.g. NASA-ISRO’s NISAR and NASA’s GEDI). The methodology described in this paper can be considered as a complimentary tool to the existing PolInSAR technique and also serves as an observing prototype for the future spaceborne missions of repeatpass InSAR in fusion with lidar (e.g. NISAR and GEDI).