Search NASA⌕ Search

SEARCH · Search NASA

Results for “JET TRANSPORT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Takeoff certification considerations for large subsonic and supersonic transport airplanes using the Ames flight simulator for advanced aircraft

Data for use in development of takeoff airworthiness standards for new aircraft designs such as the supersonic transport (SST) and the large wide-body subsonic jet transport are provided. An advanced motion simulator was used to compare the performance and handling characteristics of three representative large jet transports during specific flight certification tasks. Existing regulatory constraints and methods for determining rotation speed were reviewed, and the effects on takeoff performance of variations in rotation speed, pitch attitude, and pitch attitude rate during the rotation maneuver were analyzed. A limited quantity of refused takeoff information was obtained. The aerodynamics, wing loading, and thrust-to-weight ratio of the subject SST resulted in takeoff speeds limited by climb (rather than lift-off) considerations. Take-off speeds based on U.S. subsonic transport requirements were found unacceptable because of the criticality of rotation-abuse effects on one-engine-inoperative climb performance. Adequate safety margin was provided by takeoff speeds based on proposed Anglo-French supersonic transport (TSS) criteria, with the limiting criterion being that takeoff safety speed be at least 1.15 times the one-engine-inoperative zero-rate-of-climb speed. Various observations related to SST certification are presented.

Snyder, C. T.↗
DOE OSTI2020

Comparing particle transport in JET and DIII-D plasmas: gyrokinetic and gyrofluid modelling

The paper models the impact of fueling versus particle transport in the DIII-D and JET tokamaks. Experimentally, it was found that in JET an increase in the density peaking at lower collisionality could be attributed to an increase in core fueling, however on DIII-D, the opposite was observed. In DIII-D, the increase in density peaking was the result of an increase in inward transport, not an increase in core fueling. The paper shows that the difference in temperature gradients and thus turbulence dynamics between the two experiments can explain the experimentally observed discrepancy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Absolute atomic hydrogen density measurements in an atmospheric pressure plasma jet: generation, transport and recombination from the active discharge region to the effluent

Atomic hydrogen (H) generated by atmospheric pressure radio frequency (RF) plasma jet is investigated by two-photon absorption laser induced fluorescence in a He-H 2 mixture. The reported time and spatially resolved H density profiles enable a detailed analysis of the species generation, transport and decay along the axis of symmetry of the jet. Here, the H density distribution for a continuous RF plasma jet corresponds well with the outcome of a Pseudo-1D plug flow model. In addition, RF power modulation has a strong effect on the H density in the active discharge region but has a negligible effect on the H density in the far effluent.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2011

Development of the Transport Class Model (TCM) Aircraft Simulation From a Sub-Scale Generic Transport Model (GTM) Simulation

A six degree-of-freedom, flat-earth dynamics, non-linear, and non-proprietary aircraft simulation was developed that is representative of a generic mid-sized twin-jet transport aircraft. The simulation was developed from a non-proprietary, publicly available, subscale twin-jet transport aircraft simulation using scaling relationships and a modified aerodynamic database. The simulation has an extended aerodynamics database with aero data outside the normal transport-operating envelope (large angle-of-attack and sideslip values). The simulation has representative transport aircraft surface actuator models with variable rate-limits and generally fixed position limits. The simulation contains a generic 40,000 lb sea level thrust engine model. The engine model is a first order dynamic model with a variable time constant that changes according to simulation conditions. The simulation provides a means for interfacing a flight control system to use the simulation sensor variables and to command the surface actuators and throttle position of the engine model.

Hueschen, Richard M.↗
DOE OSTI2025

Bayesian inference analysis of jet quenching using inclusive jet and hadron suppression measurements

The JETSCAPE Collaboration reports a new determination of the jet transport parameter $\hat{q}$ in the quark-gluon plasma (QGP) using Bayesian inference, incorporating all available inclusive hadron and jet yield suppression data measured in heavy-ion collisions at the BNL Relativistic Heavy Ion Collider (RHIC) and the CERN Large Hadron Collider (LHC). This multi-observable analysis extends the previously published JETSCAPE Bayesian inference determination of $\hat{q}$, which was based solely on a selection of inclusive hadron suppression data. jetscape is a modular framework incorporating detailed dynamical models of QGP formation and evolution, and jet propagation and interaction in the QGP. Virtuality-dependent partonic energy loss in the QGP is modeled as a thermalized weakly coupled plasma, with parameters determined from Bayesian calibration using soft-sector observables. This Bayesian calibration of $\hat{q}$ utilizes active learning, a machine-learning approach, for efficient exploitation of computing resources. The experimental data included in this analysis span a broad range in collision energy and centrality, and in transverse momentum. In order to explore the systematic dependence of the extracted parameter posterior distributions, several different calibrations are reported, based on combined jet and hadron data; on jet or hadron data separately; and on restricted kinematic or centrality ranges of the jet and hadron data. Tension is observed in comparison of these variations, providing new insights into the physics of jet transport in the QGP and its theoretical formulation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Dijet Acoplanarity in CUJET3 as a Probe of the Nonperturbative Color Structure of QCD Perfect Fluids

Using the CUJET3=DGLV+VISHNU jet-medium interaction framework, we show that dijet azimuthal acoplanarity in high energy A + A collisions is sensitive to possible non-perturbative enhancement of the jet transport coefficient, $\hat{q}$(T,E), in the QCD crossover temperature T ~ 150–300 MeV range. With jet-medium couplings constrained by global RHIC& LHC χ 2 fits to nuclear modification data on R AA (p T > 20) GeV, we compare predictions of the medium induced dijet transverse momentum squared, $Q_s^2~\langle \hat{q}L\rangle~ΔΦ^2E^2$, in two models of the temperature, T, and jet energy E dependence of the jet medium transport coefficient, $\hat{q}$(T,E)). In one model, wQGP, the chromo degrees of freedom (dof) are approximated by a perturbative dielectric gas of quark and gluons dof. In the second model, sQGMP, we consider a nonperturbative partially confined semi-Quark-Gluon-Monopole-Plasma with emergent color magnetic dof constrained by lattice QCD data. Unlike the slow variation of the scaled jet transport coefficient, $\hat{q}_{wQGP}/T^3$, the sQGMP model $\hat{q}_{sQGMP}/T^3$ features a sharp maximum in the QCD confinement crossover T range. We show that the dijet path averaged medium induced azimuthal acoplanarity, Δφ 2 , in sQGMP is robustly ~ 2 times larger than in perturbative wQGP. even though the radiative energy loss in both models is very similar as needed to fit the same R AA data. Future A+A dijet acoplanarity measurements constrained together with single jet R AA and ν n measurements therefore appears to be a promising strategy to search for possible signatures of critical opalescence like phenomena in the QCD confinement temperature range.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1982

Pilot selection and training

Personality and situational factors relevant to individual and group performance in highly demanding environments, such as those faced by astronauts or by jet transport crew, are discussed. It is emphasized that although technical competence and proficiency in pilot selection are prerequisites for safety, operating a modern jet transport is a group endeavor that requires the effective coordination of the entire crew. A self-report test battery for measuring positive and negative personality traits of pilot candidates, termed the Personal Characteristics Inventory, is described.

Helmreich, Robert L.↗
NASA NTRS1985

Aerodynamic performance investigation of advanced mechanical suppressor and ejector nozzle concepts for jet noise reduction

Advanced Supersonic Transport jet noise may be reduced to Federal Air Regulation limits if recommended refinements to a recently developed ejector shroud exhaust system are successfully carried out. A two-part program consisting of a design study and a subscale model wind tunnel test effort conducted to define an acoustically treated ejector shroud exhaust system for supersonic transport application is described. Coannular, 20-chute, and ejector shroud exhaust systems were evaluated. Program results were used in a mission analysis study to determine aircraft takeoff gross weight to perform a nominal design mission, under Federal Aviation Regulation (1969), Part 36, Stage 3 noise constraints. Mission trade study results confirmed that the ejector shroud was the best of the three exhaust systems studied with a significant takeoff gross weight advantage over the 20-chute suppressor nozzle which was the second best.

Wagenknecht, C. D.↗
NASA NTRS1992

Building vibrations induced by noise from rotorcraft and propeller aircraft flyovers

Noise and building vibrations were measured for a series of helicopter and propeller-driven aircraft flyovers at WFF during May 1978. The building response data are compared with similar data acquired earlier at sites near Dulles and Kennedy Airports for operation of commercial jet transports, including the Concorde supersonic transport. Results show that noise-induced vibration levels in windows and walls are directly proportional to sound pressure level and that for a given noise level, the acceleration levels induced by a helicopter or a propeller-driven aircraft flyover cannot be distinguished from the acceleration levels induced by a commercial jet transport flyover. Noise-induced building acceleration levels were found to be lower than those levels which might be expected to cause structural damage and were also lower than some acceleration levels induced by such common domestic events as closing windows and doors.

Shepherd, Kevin P.↗
NASA NTRS1984

Investigation, development and application of optimal output feedback theory. Volume 2: Development of an optimal, limited state feedback outer-loop digital flight control system for 3-D terminal area operation

This report contains the development of a digital outer-loop three dimensional radio navigation (3-D RNAV) flight control system for a small commercial jet transport. The outer-loop control system is designed using optimal stochastic limited state feedback techniques. Options investigated using the optimal limited state feedback approach include integrated versus hierarchical control loop designs, 20 samples per second versus 5 samples per second outer-loop operation and alternative Type 1 integration command errors. Command generator tracking techniques used in the digital control design enable the jet transport to automatically track arbitrary curved flight paths generated by waypoints. The performance of the design is demonstrated using detailed nonlinear aircraft simulations in the terminal area, frequency domain multi-input sigma plots, frequency domain single-input Bode plots and closed-loop poles. The response of the system to a severe wind shear during a landing approach is also presented.

Broussard, J. R.↗
NASA NTRS1979

Aircraft energy efficiency laminar flow control glove flight conceptual design study

A laminar flow control glove applied to the wing of a short to medium range jet transport with aft mounted engines was designed. A slotted aluminum glove concept and a woven stainless steel mesh porous glove concept suction surfaces were studied. The laminar flow control glove and a dummy glove with a modified supercritical airfoil, ducting, modified wing leading and trailing edges, modified flaps, and an LFC trim tab were applied to the wing after slot spacing suction parameters, and compression power were determined. The results show that a laminar flow control glove can be applied to the wing of a jet transport with an appropriate suction system installed.

Wright, A. S.↗
NASA NTRS2004

Design and Testing of a Low Noise Flight Guidance Concept

A flight guidance concept was developed to assist in flying continuous descent approach (CDA) procedures designed to lower the noise under the flight path of jet transport aircraft during arrival operations at an airport. The guidance consists of a trajectory prediction algorithm that was tuned to produce a high-efficiency, low noise flight profile with accompanying autopilot and flight display elements needed by the flight control system and pilot to fly the approach. A key component of the flight guidance was a real-time display of energy error relative to the predicted flight path. The guidance was integrated with the conventional Flight Management System (FMS) guidance of a modern jet transport airplane and tested in a high fidelity flight simulation. A charted arrival procedure, which allowed flying conventional arrivals, CDA arrivals with standard guidance, and CDA arrivals with the new low noise guidance, was developed to assist in the testing and evaluation of the low noise guidance concept. Results of the simulation testing showed the low noise guidance was easy to use by airline pilot test subjects and effective in achieving the desired noise reduction. Noise under the flight path was reduced by at least 2 decibels in Sound Exposure Level (SEL) at distances from about 3 nautical miles out to about 17.5 nautical miles from the runway, with a peak reduction of 8.5 decibels at about 10.5 nautical miles. Fuel consumption was also reduced by about 17% for the LNG conditions compared to baseline runs for the same flight distance. Pilot acceptance and understanding of the guidance was quite high with favorable comments and ratings received from all test subjects.

Williams, David H.↗
NASA NTRS1973

A study to determine the applicability of noise abatement approach procedures to McDonnell Douglas Aircraft

Analyses of McDonnell Douglas DC-8, DC-9, and DC-10 jet transports were conducted to investigate the applicability of two segment approach noise abatement procedures to these airplanes. All models had the required glide slope capability at the certified landing flap settings. The DC-8 models would probably be limited to an upper segment glide slope of 5.5 degrees and would probably not be suitable for the two segment procedure in icing conditions. The DC-8 would not be compatible with this procedure at a reduced landing flap setting. The feasibility of installing a two segment approach system in the Douglas-built fleet of commercial jet transports from a hardware viewpoint is discussed. The candidate system consists of a two segment computer plus the necessary peripheral equipment interfaced with the existing autopilot and associated avionics. The required modifications and additions to existing equipment are described and the attendant costs estimated. Potential problems which may be encountered are also discussed.

Painter, J. A.↗
NASA NTRS1986

A high resolution spatial and temporal multiple Doppler analysis of a microburst and its application to aircraft flight simulation

Multiple Doppler radar data collected during the Joint Airport Weather Studies (JAWS) Project is used to synthesize the three-dimensional wind in the region of a microburst. The particular microburst used in this study is the strongest one to date for which three-dimensional winds have been recovered. As a diagnostic tool, a six-DOF numerical aircraft model having characteristics similar to 727 series aircraft is used to investigate jet transport aircraft response to observed microburst winds during simulated approaches and departures. Simple pilot control laws are used to adjust thrust, pitch, roll, and yaw so as to maintain given approach or departure parameters. Generally, when horizontal wind shear along the approach or departure path is 0.01/s or greater, the model is unable to maintain the desired approach path and suffers a significant reduction in climb performance during a go-around or departure. Although the mean wind shear along a path gives a good qualitative measure of the wind shear threat to a jet transport, different paths with similar mean shears can yield markedly different results, as do the same paths through the microburst at different times. These findings are a direct consequence of the fine temporal and spatial scale of microburst winds. During any given modeled aircraft traverse through the region of highest horizontal shear, time variations in the microburst wind field are shown to have an insignificant effect on the modeled flight path. This is because the traverse period is short (30 s) compared to the lifetime of a microburst (300-600 s).

Elmore, K. L.↗
NASA NTRS1991

Optimal aircraft performance during microburst encounter

The effects of microburst characteristics on the optimal penetration performance of jet transport and general aviation aircraft are presented. The purpose is to determine the best possible performance that can be achieved in a broad range of microbursts. A secondary goal is to illustrate good strategies for dealing with a range of microbursts during takeoff and landing. Over 1100 optimal trajectories were computed for two aircraft types flying through idealized microbursts using a Successive Quadratic Programs trajectory optimization algorithm. Contours of safety metrics are plotted as functions of the length scales, magnitudes, and locations of horizontal wind shears and vertical downdrafts. These performance contours show three length-scale regimes for optimal microburst penetration. At short length scales, hazards usually associated with gustiness predominate (e.g., high normal load factor, rotational upset). At intermediate length scales, a degraded ability to maintain flight path and/or vertical velocity poses the most serious threat. At very long microburst length scales, excessive touchdown velocities may result. The ability to transit a microburst successfully also varies strongly with microburst location. The results show that both aircraft types could penetrate some very severe microbursts if optimal control histories were followed. Nevertheless, these control strategies assume perfect prior knowledge of the wind, and practical limits to successful encounter with real-time control capabilities would be lower. The optimally controlled jet transport can successfully penetrate higher intensity microbursts than can the general aviation aircraft.

Psiaki, Mark L.↗
NASA NTRS1975

Flutter suppression and gust alleviation using active controls

Application of the aerodynamic energy approach to some problems of flutter suppression and gust alleviation were considered. A simple modification of the control-law is suggested for achieving the required pitch control in the use of a leading edge - trailing edge activated strip. The possible replacement of the leading edge - trailing edge activated strip by a trailing edge - tab strip is also considered as an alternate solution. Parameters affecting the performance of the activated leading edge - trailing edge strip were tested on the Arava STOL Transport and the Westwind Executive Jet Transport and include strip location, control-law gains and a variation in the control-law itself.

Nissim, E.↗