SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Aerodynamic performance characteristics of three entry vehicles designed for maximum L/D ratio of three and two at Mach 19 and Reynolds number 3,200,000 tested in 22-inch Langley helium tunnel
Apollo command module, biconic and cone hyperbolic reentry vehicles engineering, discussing L/D ratio, heat protection and weight
Lifting entry vehicles night landing flight simulation by night approaches and landings of piloted fighter aircraft with low L/D ratio
All-flexible parawing as primary descent system for large spacecraft landing, discussing configuration, structural arrangement, multistage reefing and L/D performance tests
This paper discusses the results of the IFR flight studies and briefly presents two terminal area guidance schemes specifically designed for terminal area energy management and guidance of unpowered, low L/D vehicles.
A summary of the aerodynamic characteristics of the delta orbiter space shuttle vehicle is presented. Selected guidance and control system parameters, flight path geometry, landing performance obtained with winds and turbulence, and the influence of vehicle L/D on that performance are included.
Tests were conducted with plain bearings running with three types of three-lobe journals. The bearings, with a nominal 3.8-centimeter (1.5-in.) diameter and L/D of 1, were tested at 300 K (80 F) under stable conditions to 5400 rpm. The lobed configurations tested, in order of diminishing stability, were a tilted-lobe journal with grooves, a tilted-lobe journal without grooves, and a centrally lobed journal without grooves. A previously tested three-tilted-lobe bearing with grooves, running with a plain journal, was somewhat more stable than the tilted-lobe or centrally lobed journals.
A progress report is given on the first phase of a research project to develop a system of Integrated Programs for Aerospace-Vehicle Design (IPAD) which is intended to automate to the largest extent possible the preliminary and detailed design of advanced aircraft. The approach used is to build a pilot system and simultaneously to carry out two major contractual studies to define a practical IPAD system preparatory to programing. The paper summarizes the specifications and goals of the IPAD system, the progress to date, and any conclusion reached regarding its feasibility and scope. Sample calculations obtained with the pilot system are given for aircraft preliminary designs optimized with respect to discipline parameters, such as weight or L/D, and these results are compared with designs optimized with respect to overall performance parameters, such as range or payload.
An approach to calculating optimal, gliding flight paths of the type associated with the space shuttle's transition from entry to cruising flight is presented. Kinetic energy and total energy (per unit weight) replace velocity and time in the dynamic equations, reducing the dimension and complexity of the problem. The capability for treating integral and terminal penalties (as well as Mach number effects) is retained in the numerical optimization; hence, stability and control boundaries can be observed as trajectories to the desired final energy, flight path angle, and range are determined. Numerical results show that the 'jump' to the 'front-side of the L/D curve' need not be made until the end of the transition and that the dynamic model provides a conservative range estimate. Alternatives for real-time trajectory control are discussed.
An approach to calculating optimal, gliding flight paths of the type associated with the space shuttle's transition from entry to cruising flight is presented. Kinetic energy and total energy (per unit weight) replace velocity and time in the dynamic equations, reducing the dimension and complexity of the problem. The capability for treating integral and terminal penalties (as well as Mach number effects) is retained in the numerical optimization; hence, stability and control boundaries can be observed as trajectories to the desired final energy, flight path angle, and range are determined. Numerical results show that the jump to the front-side of the L/D curve need not be made until the end of the transition and that the dynamic model provides a conservative range estimate. Alternatives for real time trajectory control are discussed.
This paper summarizes the preliminary design studies of unmanned electric propulsion spacecraft, with primary emphasis on the in-core thermionic reactor power subsystem. A 70-kWe power subsystem, with an external-fuel thermionic reactor, is shown integrated into a large L/D (about 20) electric propulsion spacecraft. The 70-kWe spacecraft is designed for launch to earth escape with a Titan-Centaur. Two 300-kWe reactor designs (external-fuel and flashlight designs from Atomic Energy Commission contracted studies) are integrated into 270-kWe electric propulsion spacecraft. The 270-kWe spacecraft are designed for launch to a 700-nmi earth orbit with a Titan III-C/7 booster. The 70-kWe thermionic reactor power subsystem is also conceptually shown as a space base power plant.
Groove parameters were determined to maximize the stability of herringbone grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed using a small eccentricity, infinite groove analysis in conjunction with: (1) a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers, and (2) a newly-developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves enable one to choose the optimum bearing for a wide range of operating conditions. These include: (1) compressibility numbers from 0 (incompressible) to 80, (2) length to diameter ratios from 1/4 to 2, and (3) smooth or grooved member rotating. Compared to bearings optimized to maximize load capacity, bearings optimized for stability: (1) allow a thousandfold increase in bearing-supported mass in some cases before onset of instability (the most dramatic increase are for bearings with small L/D operating at high compressibility numbers), and (2) lose no more than 77-percent of their load capacity in any case studied. Stability is much greater when the grooved member rotates.
An experimental program comprising model nozzle and full-scale engine tests was undertaken to acquire parametric data for acoustically lined ejectors applied to primary jet noise suppression. Ejector lining design technology and acoustical scaling of lined ejector configurations were the major objectives. Ground static tests were run with a J-75 turbojet engine fitted with a 37-tube, area ratio 3.3 suppressor nozzle and two lengths of ejector shroud (L/D = 1 and 2). Seven ejector lining configurations were tested over the engine pressure ratio range of 1.40 to 2.40 with corresponding jet velocities between 305 and 610 M/sec. One-fourth scale model nozzles were tested over a pressure ratio range of 1.40 to 4.0 with jet total temperatures between ambient and 1088 K. Scaling of multielement nozzle ejector configurations was also studied using a single element of the nozzle array with identical ejector lengths and lining materials. Acoustic far field and near field data together with nozzle thrust performance and jet aerodynamic flow profiles are presented.
The results of a thermal-structural test program to verify the performance of a metallic/radiative Thermal Protection System (TPS) under reentry conditions are presented. This TPS panel is suitable for multiple reentry, high L/D space vehicles, such as the NASA space shuttle, having surface temperatures up to 1200 C (2200 F). The TPS panel tested consists of a corrugation-stiffened, beaded-skin TD Ni-20Cr metallic heat shield backed by a flexible fibrous quartz and radiative shield insulative system. Test conditions simulated the critical heating and aerodynamic pressure environments expected during 100 repeated missions of a reentry vehicle. Temperatures were measured during each reentry cycle; heat-shield flatness surveys to measure permanent set of the metallic components were made every 10 cycles. The TPS panel, in spite of localized surface failures, performed its designated function.
Male and female Sprague-Dawley rats derived from a single mating were raised for three generations under constant centrifugation at 1.03 G (Rotation Controls) and at 2 G. When the third generation rats were 3 months old, they were sacrificed, and their femurs removed. After fixation and cleaning, the femurs were then measured for length and diameter. Then right femurs were sectioned longitudinally, left femurs transversely. After staining with Hematoxylin and Eosin, right femurs were examined for ossification patterns and left femurs were measured for cortical thickness. All rotation control rats showed marked stimulation of ossification in the femoral head, and males showed significant cortical thinning when compared to non-rotated earth gravity controls. All 2 G femurs showed decreased length and aspect (L/D) ratios, and increased cortical thickness/diameter ratios when compared to earth controls or rotation controls. Ossification of the femoral head was slightly advanced, while the distal epiphyseal plate was thinned.
Optimization of L/D through minimizing induced drag through a detailed flow study together with force, pressure and vorticity measurements is considered. Flow visualization with neutral helium bubbles provides an excellent means of observing the effects of configuration changes.
A brief examination of the performance figures achieved by modern soaring machines and a little reflection on the often huge disparity in L/D values between sailplanes and GA aircraft indicates that careful attention to lessons learned in sailplane design and manufacture hold realistic promise for substantial gains in the aerodynamic efficiency of several GA types.
A semi-empirical entrainment theory was employed to correlate the measured temperature depression, Delta T, in a developed cavity for a venturi. This theory correlates Delta t in terms of the dimensionless numbers of Nusselt, Reynolds, Froude, Weber and Peclet, and dimensionless cavity length, L/D. These correlations are then compared with similar correlations for zero and quarter caliber ogives. In addition, cavitation number data for both limited and developed cavitation in venturis are presented.