SEARCH · Search NASA

Results for “LIFT CURVES - SLOPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Tornadoes in Southeast South America: Mesoscale to Planetary-Scale Environments

Abstract A multiscale analysis of the environment supporting tornadoes in southeast South America (SESA) was conducted based on a self-constructed database of 74 reports. Composites of environmental and convective parameters from ERA5 were generated relative to tornado events. The distribution of the reported tornadoes maximizes over the Argentine plains, while events are rare close to the Andes and south of Sierras de Córdoba. Events are relatively common in all seasons except in winter. Proximity environment evolution shows enhanced instability, deep-layer vertical wind shear, storm-relative helicity, reduced convective inhibition, and a lowered lifting condensation level before or during the development of tornadic storms in SESA. No consistent signal in low-level wind shear is seen during tornado occurrence. However, a curved hodograph with counterclockwise rotation is present. The Significant Tornado Parameter (STP) is also maximized prior to tornadogenesis, most strongly associated with enhanced CAPE. Differences in the convective environment between tornadoes in SESA and the U.S. Great Plains are discussed. On the synoptic scale, tornado events are associated with a strong anomalous trough crossing the southern Andes that triggers lee cyclogenesis, subsequently enhancing the South American low-level jet (SALLJ) that increases moisture advection to support deep convection. This synoptic trough also enhances vertical shear that, along with enhanced instability, sustains organized convection capable of producing tornadic storms. At planetary scales, the tornadic environment is modulated by Rossby wave trains that appear to be forced by convection near northern Australia. Madden–Julian oscillation phase 3 preferentially occurs 1–2 weeks ahead of tornado occurrence. Significance Statement The main goal of this study is to describe what atmospheric conditions (from local to global scales) are present prior to and during tornadic storms impacting southeast South America (SESA). Increasing potential for deep convection, wind shear, and potential for rotating updrafts, as well as reducing convective inhibition and cloud-base height, are predominant a few hours before and during the events in connection to low-level northerly winds enhancing moisture transport to the region. Remote convective activity near northern Australia appears to influence large-scale atmospheric circulation that subsequently triggers convective storms supporting tornadogenesis 1–2 weeks later in SESA. Our findings highlight the importance of accounting for atmospheric processes occurring at different scales to understand and predict tornado occurrences.

Meteorology & Atmospheric Sciences↗

NASA NTRS1933

Lift and Drag Characteristics and Gliding Performance of an Autogiro as Determined in Flight

This report presents the results of flight test of the Pitcairn "PCA-2" autogiro. Lift and drag coefficients with the propeller stopped have been determined over approximately a 90 degree range of angles of attack. Based on the sum of fixed-wing and swept-disk areas, the maximum lift coefficient is 0.895, the minimum drag coefficient with propeller stopped is 0.015, and the maximum l/d with propeller stopped is 4.8. Lift coefficients were found also with the propeller delivering positive thrust and did not differ consistently from those found with propeller stopped. Curves of gliding performance included in this report show a minimum vertical velocity of 15 feet per second at an air speed of 36 miles per hour and a flight-path angle of -17 degrees. In vertical descent the vertical velocity is 35 feet per second.

Wheatley, John B↗

NASA NTRS1982

A model for unsteady transonic indicial responses

A method of characterizing the indicial curve for the response frequencies of flutter in the transonic regime by means of a time scale parameter is illustrated. Time linearization of the unsteady potential equation is assumed adequate and the perturbed potential about a steady flow is defined with appropriate boundary conditions. An indicial motion can then be obtained for a given mode, with the lift and drag coefficients which result from a step change in incidence or control surface deflection available to describe any kind of motion. The lift and drag coefficients are shown to result analytically by addition of the multiplicand involving the time scale parameter. If the coefficients are maximized, then at reduced frequencies only two parameters are necessary to form the indicial response curve.

Fung, K.-Y.↗

NASA NTRS1959

Static Stability Characteristics of Three Thick Wing Models with Parabolic Plan Forms at a Mach Number of 3.11

An experimental investigation has been made to determine the static stability characteristics of three thick wing models with parabolic plan forms at a Mach number of 3.11 for angles of attack from about -6 to 16 deg. The primary variable was aspect ratio, with the plan-form area and the ratio of base height to span kept the same for all three models. All models had stable, linear pitching-moment curves about the quarter chord of the wing mean aerodynamic chord. The model with the lowest aspect ratio attained a maximum untrimmed lift-drag ratio of about 5.0 at an angle of attack of about 8 deg. Increasing the aspect ratio (which was accompanied by an increase in base area because the ratio of the base height to span was kept constant) caused a decrease in maximum lift-drag ratio. All models were directionally stable for the range of angle of attack of the tests. Addition of a vertical tail to the models caused an increase in the directional stability over the angle-of-attack range. In general, the lateral aerodynamic characteristics of the models were not linear functions of angle of attack over any appreciable angle-of-attack range.

Queijo, M. J.↗

NASA NTRS2019

Performance Optimization of Plate Airfoils for Martian Rotor Applications Using a Genetic Algorithm

The Mars Helicopter Technology Demonstrator will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. The goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Research is performed at the Jet Propulsion Laboratory and NASA Ames Research Center to extend these capabilities and develop the Mars Science Helicopter as the next possible step for Martian rotorcraft. The Mars Science Helicopter mass is scaled up to the 5 to 20 kg range, allowing a greater payload (approximately 0.5 to 2.0 kg), and greater range (approximately 3 km). Key to achieving these targets is careful aerodynamic rotor design. The Martian atmosphere’s low density and the small helicopter rotors result in very low chord-based Reynolds number flows, which reduces rotor performance. A continuous genetic algorithm is developed to optimize airfoil shapes at representative conditions for the Martian atmosphere. Previous research indicates that sharp leading edges and plate-like airfoils can out-perform conventional airfoil shapes. The present optimization allows for camber and thickness variation of curved and polygonal thin airfoils with sharp leading edges. The airfoil performance is evaluated at the highest attainable liftto- drag ratio near a moderate lift coefficient at compressible Mach numbers, as expected for Martian rotor application. Increases between 16% and 29% in airfoil lift-to-drag ratio at fixed lift coefficients are observed when compared with the Mars Helicopter Technology Demonstrator airfoils. Improvements in hover figure of merit are estimated to be between 4% and 10%, when applied to the Mars Helicopter Technology Demonstrator.

Koning, Witold J. F.↗

NASA NTRS1944

Intercooler cooling-air weight flow and pressure drop for minimum drag loss

An analysis has been made of the drag losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give a minimum drag loss for any given cooling effectiveness and, thus, a maximum power-plant net gain due to charge-air cooling. The drag losses considered in this analysis are those due to (1) the extra drag imposed on the airplane by the weight of the intercooler, its duct, and its supports and (2) the drag sustained by the cooling air in flowing through the intercooler and its duct. The investigation covers a range of conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and supercharger adiabatic efficiency. The optimum values of cooling air pressure drop and weight flow ratio are tabulated. Curves are presented to illustrate the results of the analysis.

Reuter, J George↗

NASA NTRS1929

An Investigation of the Aerodynamic Characteristics of an Airplane Equipped with Several Different Sets of Wings

This investigation was conducted by the National Advisory Committee for Aeronautics at Langley Field, Va., at the request of the Army Air Corps, for the purpose of comparing the full scale lift and drag characteristics of an airplane equipped with several sets of wings of commonly used airfoil sections. A Sperry Messenger Airplane with wings of R.A.F.-15, U.S.A.-5, U.S.A.-27, and Gottingen 387 airfoil sections was flown and the lift and drag characteristics of the airplane with each set of wings were determined by means of glide tests. The results are presented in tabular and curve form. (author)

Crowley, J W , Jr↗

DOE OSTI2025

Long-term hydro-economic analysis tool for evaluating global groundwater cost and supply: Superwell v1.1

Abstract. Groundwater plays a key role in meeting water demands, supplying over 40 % of irrigation water globally, with this role likely to grow as water demands and surface water variability increase. A better understanding of the future role of groundwater in meeting sectoral demands requires an integrated hydro-economic evaluation of its cost and availability. Yet substantial gaps remain in our knowledge and modeling capabilities related to groundwater availability, recharge, feasible locations for extraction, extractable volumes, and associated extraction costs, which are essential for large-scale analyses of integrated human–water system scenarios, particularly at the global scale. To address these needs, we developed Superwell, a physics-based groundwater extraction and cost accounting model that operates at sub-annual temporal and at the coarsest 0.5° (≈50 km × 50 km) gridded spatial resolution with global coverage. The model produces location-specific groundwater supply–cost curves that provide the levelized cost to access different quantities of available groundwater. The inputs to Superwell include recent high-resolution hydrogeologic datasets of permeability, porosity, aquifer thickness, depth to water table, recharge, and hydrogeological complexity zones. It also accounts for well capital and maintenance costs, as well as the energy costs required to lift water to the surface. The model employs a Theis-based scheme coupled with an amortization-based cost accounting formulation to simulate groundwater extraction and quantify the cost of groundwater pumping. The result is a spatiotemporally flexible, physically realistic, economics-based model that produces groundwater supply–cost curves. We show examples of these supply–cost curves and the insights that can be derived from them across a set of scenarios designed to explore model outcomes. The supply–cost curves produced by the model show that most (90 %) nonrenewable groundwater in storage globally is extractable at costs lower than USD 0.57 m−3, while half of the volume remains extractable at under USD 0.108 m−3. The global unit cost is estimated to range from a minimum of USD 0.004 m−3 to a maximum of USD 3.971 m−3. We also demonstrate and discuss examples of how these cost curves could be used by linking Superwell's outputs with other models to explore coupled human–environmental system challenges, such as water resources planning and management, or broader analyses of multisectoral feedbacks.

Global Change Analysis Model (GCAM)↗

NASA NTRS2009

Preliminary Test Results of a Non-Contacting Finger Seal on a Herringbone-Grooved Rotor

The baseline non-contacting finger seal is a NASA patented design. The primary difference between it and Gul Aroras design patented by AlliedSignal is that there are no lift pads on the high pressure fingers. The baseline non-contacting finger seal is comprised of a back plate, aft spacer, aft (or low pressure) finger element, forward (or high pressure) finger element, forward spacer, and front plate. The components are held together with 20 flat head screws. A typical seal would have a back plate of approximately the same thickness as the front plate and would be riveted together. The thicker back plate allows use of threaded fasteners so that different finger elements can be tested without having to replace all the individual seal components. The finger elements are essentially washers made of thin sheet stock with multiple curved slots machined around the inner diameter to form the fingers. They are clocked so that the fingers of one cover the slots of the other. The aft finger element fingers have axial extensions or "lift pads" at the seal id that are concentric to the rotor. The fingers act as cantilever beams and flex in response to rotor dynamic motion and radial growth of the rotor due to centrifugal or thermal forces.

Proctor, Margaret P.↗

NASA NTRS1937

Static Thrust Analysis of the Lifting Airscrew

This report presents the results of a combined theoretical and experimental investigation conducted at the Georgia School of Technology on the static thrust of the lifting air screw of the type used in modern autogiros and helicopters. The theoretical part of this study is based on Glauert's analysis but certain modifications are made that further clarify and simplify the problem. Of these changes the elimination of the solidity as an independent parameter is the most important. The experimental data were obtained from tests on four rotor models of two, four, and five blades and, in general, agree quite well with the theoretical calculations. The theory indicates a method of evaluating scale effects on lifting air screws, and these corrections have been applied to the model results to derive general full-scale static thrust, torque, and figure-of-merit curves for constant-chord, constant-incidence rotors. Convenient charts are included that enable hovering flight performance to be calculated rapidly.

Knight, Montgomery↗

NASA NTRS1994

Dynamic ground effects flight test of an F-15 aircraft

Flight tests to determine the changes in the aerodynamic characteristics of an F-15 aircraft caused by dynamic ground effects are described. Data were obtained for low and high sink rates between 0.7 and 6.5 ft/sec and at two landing approach speeds and flap settings: 150 kn with the flaps down and 170 kn with the flaps up. Simple correlation curves are given for the change in aerodynamic coefficients because of ground effects as a function of sink rate. Ground effects generally caused an increase in the lift, drag, and nose-down pitching movement coefficients. The change in the lift coefficient increased from approximately 0.05 at the high-sink rate to approximately 0.10 at the low-sink rate. The change in the drag coefficient increased from approximately 0 to 0.03 over this decreasing sink rate range. No significant difference because of the approach configuration was evident for lift and drag; however, a significant difference in pitching movement was observed for the two approach speeds and flap settings. For the 170 kn with the flaps up configuration, the change in the nose-down pitching movement increased from approximately -0.008 to -0.016. For the 150 kn with the flaps down configuration, the change was approximately -0.008 to -0.038.

Corda, Stephen↗

NASA NTRSDate not supplied

Overlap Preservation Using Loosely-Coupled Boundary Conditions for Body-Fitted Structured Overset Grids

Several improvements are made to overlap preservation in the automated approach to generating overset structured meshes. A loosely-coupled boundary condition (LCBC) is introduced to maintain optimal overlap for surface meshes generated from overlapping initial curves. Extension of the LCBC scheme to three-dimensional volume meshing is also presented. Test cases include various rotary wing vehicles from NASA’s Revolutionary Vertical Lift Technology (RVLT) project, and the wing-body geometry from the NASA Juncture Flow Experiment. Results demonstrate improvements in donor stencil quality from the enhanced overlap between neighboring surface and volume meshes.

TTT↗

NASA NTRS1952

Effect of High-lift Devices on the Low-speed Static Lateral and Yawing Stability Characteristics of an Untapered 45 Degrees Sweptback Wing

Results of a low-speed wind-tunnel investigation to determine the effect of high-lift devices on the static lateral stability derivatives and the yawing derivatives of an untapered 45 degrees sweptback wing are presented. The tests were made in the curved-flow test section of the Langley stability tunnel at a Reynolds number of 1.1 X 10 to the sixth power.

FLAPS, LEADING EDGE - COMPLETE WINGS↗

NASA NTRS1958

Effect of Nose Length, Fuselage Length, and Nose Fineness Ratio on the Longitudinal Aerodynamic Characteristics of Two Complete Models at High Subsonic Speeds

An investigation has been made of the effects of nose length, fuselage length, and nose fineness ratio on the static longitudinal aerodynamic characteristics of an airplane model with a swept wing and low tail and of a second model with a highly tapered wing of moderate sweep and a T-tail. The tests were conducted in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92. The nose and body cross sections were circular. For either the model with the swept wing and low tail or the model with the highly tapered wing of moderate sweep and the T-tail, the effects of forebody changes amounted primarily to rotations of the pitching-moment curves (changes in static margin) over the test ranges of angle of attack and Mach number. For the range of body shapes investigated the longitudinal stability at low lift is decreased by an increase in nose length or in fuselage length or by a reduction in nose fineness ratio when the fuselage length is held constant. In general, the stability for all model configurations showed substantially the same variation with changes in forebody area moment. The forebody changes did not alter the angle of attack at which an unstable break occurred in the moment contribution of the T-tail but did alter somewhat the magnitude of the instability.

Goodson, Kenneth W.↗

NASA NTRS1946

Critical Mach Numbers of Thin Airfoil Sections with Plain Flaps

Critical Mach number as function of lift coefficient is determined for certain moderately thick NACA low-drag airfoils. Results, given graphically, included calculations on same airfoil sections with plain flaps for small flap deflections. Curves indicate optimum critical conditions for airfoils with flaps in such form that they can be compared with corresponding results for zero flap deflections. Plain flaps increase life-coefficient range for which critical Mach number is in region of high values characteristic of low-drag airfoils.

AIRFOILS - NACA 651-208 - CHARACTERISTICS LOW-DRAG↗

NASA NTRS2013

Elevated Temperature, Notched Compression Performance of Out of Autoclave Processed Composites

Curved honeycomb sandwich panels composed of carbon fiber reinforced toughened-epoxy polymer facesheets are being evaluated for potential use as payload fairing components on the NASA heavy-lift space launch system (HL-SLS). These proposed composite sandwich panels provide the most efficient aerospace launch structures, and offer mass and thermal advantages when compared with existing metallic payload fairing structures. NASA and industry are investigating recently developed carbon fiber epoxy prepreg systems which can be fabricated using out-of autoclave (OOA) processes. Specifically, OOA processes using vacuum pressure in an oven and thereby significantly reducing the cost associated with manufacturing large (up to 10 m diameter) composite structures when compared with autoclave. One of these OOA composite material systems, CYCOM(R) 5320-1, was selected for manufacture of a 1/16th scale barrel portion of the payload fairing; such that, the system could be compared with the well-characterized prepreg system, CYCOM(R) 977-3, typically processed in an autoclave. Notched compression coupons for each material were obtained from the minimum-gauge flat laminate [60/-60/0]S witness panels produced in this manufacturing study. The coupons were also conditioned to an effective moisture equilibrium point and tested according to ASTM D6484M-09 at temperatures ranging from 25 C up to 177 C. The results of this elevated temperature mechanical characterization study demonstrate that, for thin coupons, the OHC strength of the OOA laminate was equivalent to the flight certified autoclave processed composite laminates; the limitations on the elevated temperature range are hot-wet conditions up to 163 C and are only within the margins of testing error. At 25 C, both the wet and dry OOA material coupons demonstrated greater OHC failure strengths than the autoclave processed material laminates. These results indicate a substantial improvement in OOA material development and processing since previous studies have consistently reported OOA material strengths on par or below those of autoclave processed composite laminates.

Grimsley, Brian W.↗

NASA NTRS2005

Experimental Investigation of a Morphing Nacelle Ducted Fan

The application of Circulation Control to the nacelle of a shrouded fan is proposed as a means to enhance off-design performance of the shrouded fan. Typically, a fixed geometry shroud is efficient at a single operating condition. Modifying circulation about the fixed geometry is proposed as a means to virtually morph the shroud without moving surfaces. This approach will enhance off-design-point performance with minimal complexity, weight, and cost. Termed the Morphing Nacelle, this concept provides an attractive propulsion option for Vertical Take-off and Landing (VTOL) aircraft, such conceptual Personal Air Vehicle (PAV) configurations proposed by NASA. An experimental proof of concept investigation of the Morphing Nacelle is detailed in this paper. A powered model shrouded fan model was constructed with Circulation Control (CC) devices integrated in the inlet and exit of the nacelle. Both CC devices consisted of an annular jet slot directing a jet sheet tangent to a curved surface, generally described as a Coanda surface. The model shroud was tailored for axial flight, with a diffusing inlet, but was operated off-design condition as a static lifting fan. Thrust stand experiments were conducted to determine if the CC devices could effectively improve off-design performance of the shrouded fan. Additional tests were conducted to explore the effectiveness of the CC devices a means to reduce peak static pressure on the ground below a lifting fan. Experimental results showed that off-design static thrust performance of the model was improved when the CC devices were employed under certain conditions. The exhaust CC device alone, while effective in diffusing the fan exhaust and improving weight flow into shroud inlet, tended to diminish performance of the fan with increased CC jet momentum. The inlet CC device was effective at reattaching a normally stalled inlet flow condition, proving an effective means of enhancing performance. A more dramatic improvement in static thrust was obtained when the inlet and exit CC devices were operated in unison, but only over a limited range of CC jet momentum. Operating the nacelle inlet and exit CC devices together proved very effective in reducing peak ground plane static pressure, while maintaining static thrust. The Morphing Nacelle concept proved effective at enhancing off-design performance of the model; however, additional investigation is necessary to generalize the results.

Kondor, Shayne A.↗

NASA NTRS1975

Crawler Transporter Steering and Jel Systems

The transporter weighing 2.8 million kilograms (6.3 million pounds) was used to lift a 5.7-million-kilogram (12.6-million-pound) combination of mobile launcher and space vehicle, transfer this load approximately 5.6 kilometers (3.5 miles) from its point of assembly, negotiate curves of 152-meter (500-foot) mean radius, climb a 5-percent grade while maintaining the 122-meter (400-foot) structure in a vertical position within 10 minutes of arc, and smoothly position this huge structure to within plus or minus 5.1 centimeters (plus or minus 2 inches) on support pedestals at the launch pad. The crawler-transporter is described in detail.

Davis, V. L.↗