SEARCH · Search NASA

Results for “Lift”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Estimation of unsteady lift on a pitching airfoil from wake velocity surveys

The results of a joint experimental and computational study on the flowfield over a periodically pitched NACA0012 airfoil, and the resultant lift variation, are reported in this paper. The lift variation over a cycle of oscillation, and hence the lift hysteresis loop, is estimated from the velocity distribution in the wake measured or computed for successive phases of the cycle. Experimentally, the estimated lift hysteresis loops are compared with available data from the literature as well as with limited force balance measurements. Computationally, the estimated lift variations are compared with the corresponding variation obtained from the surface pressure distribution. Four analytical formulations for the lift estimation from wake surveys are considered and relative successes of the four are discussed.

Zaman, K. B. M. Q.↗

NASA NTRS1939

The Unsteady Lift of a Finite Wing

Unsteady lift function for wings of finite aspect ratio have been calculated by approximate methods involving corrections of the aerodynamic inertia and of the angle of the infinite wing. The starting lift of the finite wing is found to be only slightly less than that of the infinite wing; whereas the final lift may be considerably less. The calculations indicate that the distribution of lift near the start is similar to the final distribution. Both the indicia and the oscillating lift functions are given. Approximate operational equivalents of the functions have been devised to facilitate the calculation of lift under various conditions of motion.

Jones, Robert T↗

NASA NTRS1946

Theoretical lift and drag of thin triangular wings at supersonic speeds

A method is derived for calculating the lift and the drag due to lift of point-forward triangular wings and a restricted series of sweptback wings at supersonic speeds. The elementary or "supersonic sources" solution of the linearized equation of motion is used to find the potential function of a line of doublets. The flow about the triangular flat plate is then obtained by a surface distribution of these doublet lines. The lift-curve slope of triangular wings is found to be a function of the ratio of the tangent of the apex angle to the tangent of the Mach angle. As the apex angle approaches and becomes greater than the Mach angle, the lift coefficient of the triangular wing becomes equal to that of a two-dimensional supersonic airfoil at the same Mach number. The drag coefficient due to lift of triangular wings with leading edges well behind the Mach cone is shown to be close to that of elliptically loaded wings of the same aspect ratio in subsonic flight. The resultant force on wings with leading edges outside the Mach cone, however, is shown to act normal to the surfaces and thus an induced drag equal to the lift times the angle of attack is obtained.

Brown, Clinton E↗

NASA NTRS1993

Dust-dynamic feedbacks in the Martian atmosphere: Surface dust lifting

Numerical models have been developed to study surface dust lifting in the Martian atmosphere. The present model is comprised of interactively coupled 3-D dynamical and aerosol transport/microphysical models. The nature of possible feedbacks between surface dust lifting and the amplification/damping of near-surface wind and thermal fields and their implications for additional lifting is investigated. These studies have examined large scale Martian topography for its impact upon the ability of the atmospheric circulation to lift dust from the surface, and the particular component(s) responsible for the lifting (e.g. overturning circulation, thermal tides, baroclinic waves). Analogous experiments in which the lifted dust is radiatively inactive (passive tracer) have been conducted to act as a control against which feedbacks are defined.

Murphy, James R.↗

NASA NTRS1993

High Reynolds Number Configuration Development of a High-Lift Airfoil

An experimental program has been conducted to assess performance of a transport multielement airfoil at flight Reynolds numbers. The studies were performed at chord Reynolds numbers as high as 16 million in the NASA Langley Low Turbulence Pressure Tunnel. Sidewall boundary-layer control to enforce flow two dimensionality was provided via an endplate suction system. The basic airfoil was an 11.55 percent thick supercritical airfoil representative of the stall critical station of a new-generation transport aircraft wing. The multielement airfoil was configured as a three-element airfoil with slat and flap chord ratios of 14.48 percent and 30 percent respectively. Testing focused on the development of landing configurations with high maximum lift capability and the assessment of Reynolds and Mach number effects. Also assessed were high-lift performance effects due to devices such as drooped spoilers and trailing-edge wedges. The present experimental studies revealed significant effects on high-lift airfoil performance due to Reynolds and Mach number variations and favorable lift increments at approach angles of attack due to the use of drooped spoilers or trailing-edge wedges. However, no substantial improvements in maximum lift capability were identified. A recently developed high performance single-segment flap was also tested and results indicated considerable improvements in lift and drag performance over existing airfoils. Additionally, it was found that this new flap shape at its optimum rigging was less sensitive to Reynolds number variations than previous designs.

Walter O Valarezo↗

NASA NTRS1993

Survey of lift-fan aerodynamic technology

Representatives of NASA Ames Research Center asked that a summary of technology appropriate for lift-fan powered short takeoff/vertical landing (STOVL) aircraft be prepared so that new programs could more easily benefit from past research efforts. This paper represents one of six prepared for that purpose. The authors have conducted or supervised the conduct of research on lift-fan powered STOVL designs and some of their important components for decades. This paper will first address aerodynamic modeling requirements for experimental programs to assure realistic, trustworthy results. It will next summarize the results or efforts to develop satisfactory specialized STOVL components such as inlets and flow deflectors. It will also discuss problems with operation near the ground, aerodynamics while under lift-fan power, and aerodynamic prediction techniques. Finally, results of studies to reduce lift-fan noise will be presented. The paper will emphasize results from large scale experiments, where available, for reasons that will be brought out in the discussion. Some work with lift-engine powered STOVL aircraft is also applicable to lift-fan technology and will be presented herein. Small-scale data will be used where necessary to fill gaps.

Hickey, David H.↗

NASA NTRS1992

Lift augmentation on a delta wing via leading edge fences and the Gurney flap

Wind tunnel tests were conducted on two devices for the purpose of lift augmentation on a 60 deg delta wing at low speed. Lift, drag, pitching moment, and surface pressures were measured. Detailed flow visualization was also obtained. Both the leading edge fence and the Gurney flap are shown to increase lift. The fences and flap shift the lift curve as much as 5 deg and 10 deg, respectively. The fences aid in trapping vortices on the upper surface, thereby increasing suction. The Gurney flap improves circulation at the trailing edge. The individual influences of both devices are roughly additive, creating high lift gain. However, the lower lift to drag ratio and the precipitation of vortex burst caused by the fences, and the nose down pitching moment created by the flap are also significant factors.

Buchholz, Mark D.↗

NASA NTRS1994

Experiments on the flow field physics of confluent boundary layers for high-lift systems

The use of sub-scale wind tunnel test data to predict the behavior of commercial transport high lift systems at in-flight Reynolds number is limited by the so-called 'inverse Reynolds number effect'. This involves an actual deterioration in the performance of a high lift device with increasing Reynolds number. A lack of understanding of the relevant flow field physics associated with numerous complicated viscous flow interactions that characterize flow over high-lift devices prohibits computational fluid dynamics from addressing Reynolds number effects. Clearly there is a need for research that has as its objective the clarification of the fundamental flow field physics associated with viscous effects in high lift systems. In this investigation, a detailed experimental investigation is being performed to study the interaction between the slat wake and the boundary layer on the primary airfoil which is known as a confluent boundary layer. This little-studied aspect of the multi-element airfoil problem deserves special attention due to its importance in the lift augmentation process. The goal of this research is is to provide an improved understanding of the flow physics associated with high lift generation. This process report will discuss the status of the research being conducted at the Hessert Center for Aerospace Research at the University of Notre Dame. The research is sponsored by NASA Ames Research Center under NASA grant NAG2-905. The report will include a discussion of the models that have been built or that are under construction, a description of the planned experiments, a description of a flow visualization apparatus that has been developed for generating colored smoke for confluent boundary layer studies and some preliminary measurements made using our new 3-component fiber optic LDV system.

Nelson, Robert C.↗

NASA NTRS1993

Lift Augmentation on a Delta Wing via Leading Edge Fences and the Gurney Flap

Wind tunnel tests have been conducted on two devices for the purpose of lift augmentation on a 60 deg delta wing at low speed. Lift, drag, pitching moment, and surface pressures were measured. Detailed flow visualization was also obtained. Both the leading edge fence and the Gurney flap are shown to increase lift. The fences and flap shift the lift curve by as much as 5 deg and 10 deg, respectively. The fences aid in trapping vortices on the upper surface, thereby increasing suction. The Gurney flap improves circulation at the trailing edge. The individual influences of both devices are roughly additive, creating high lift gain. However, the lower lift to drag ratio and the precipitation of vortex burst caused by the fences, and the nose down pitching moment created by the flap are also significant factors.

Buchholz, Mark D.↗

NASA NTRS1959

Approach and Landing Investigation at Lift-Drag Ratios of 2 to 4 Utilizing a Straight-Wing Fighter Airplane

A series of landings was performed with a straight-wing airplane to evaluate the effect of low lift-drag ratios on approach and landing characteristics. Landings with a peak lift-drag ratio as low as 3 were performed by altering the airplane configuration (extending speed brakes, flaps, and gear and reducing throttle setting). As lift-drag ratio was reduced, it was necessary either to make the landing pattern tighter or to increase initial altitude, or both. At the lowest lift-drag ratio the pilots believed a 270 deg overhead pattern was advisable because of the greater ease afforded in visually positioning the airplane. The values of the pertinent flare parameters increased with the reduction of lift-drag ratio. These parameters included time required for final flare; speed change during final flare; and altitude, glide slope, indicated airspeed, and vertical velocity at initiation of final flare. The pilots believed that the tolerable limit was reached with this airplane in the present configuration, and that if, because of a further reduction in lift-drag ratio, more severe approaches than those experienced in this program were attempted, additional aids would be required to determine the flare-initiation point.

Matranga, Gene J.↗

NASA NTRS1999

Piloted Simulation Study of the Effects of High-Lift Aerodynamics on the Takeoff Noise of a Representative High-Speed Civil Transport

As part of an effort between NASA and private industry to reduce airport-community noise for high-speed civil transport (HSCT) concepts, a piloted simulation study was initiated for the purpose of predicting the noise reduction benefits that could result from improved low-speed high-lift aerodynamic performance for a typical HSCT configuration during takeoff and initial climb. Flight profile and engine information from the piloted simulation were coupled with the NASA Langley Aircraft Noise Prediction Program (ANOPP) to estimate jet engine noise and to propagate the resulting source noise to ground observer stations. A baseline aircraft configuration, which also incorporated different levels of projected improvements in low-speed high-lift aerodynamic performance, was simulated to investigate effects of increased lift and lift-to-drag ratio on takeoff noise levels. Simulated takeoff flights were performed with the pilots following a specified procedure in which either a single thrust cutback was performed at selected altitudes ranging from 400 to 2000 ft, or a multiple-cutback procedure was performed where thrust was reduced by a two-step process. Results show that improved low-speed high-lift aerodynamic performance provides at least a 4 to 6 dB reduction in effective perceived noise level at the FAA downrange flyover measurement station for either cutback procedure. However, improved low-speed high-lift aerodynamic performance reduced maximum sideline noise levels only when using the multiple-cutback procedures.

Glaab, Louis J.↗

NASA NTRS1961

Effect of Ratio of Jet Area to Total Area and of Pressure Ratio on Lift Augmentation of Annular Jets in Ground Effect Under Static Conditions

The present investigation was undertaken to determine the effects of the ratio of jet area to total area and of the pressure ratio on the lift-augmentation characteristics of annular jets in ground effect. The investigation was made over an area-ratio range of 1.00 to 0.02 and a pressure-ratio range of about 1.04 to 1.95. Several configurations with center jets were tested through an angle-of-attack range to determine the pitching-moment characteristics. The tests were conducted in a static test room with the use of the compressed-air facilities. The results show that lift augmentation increases somewhat as the area ratio is reduced to about 0.10, below which it deteriorates due to thin jet mixing. The effect of pressure ratio on lift was negligible for the area-ratio range investigated. Calculations of the lift per air horsepower for a given base loading indicate that the greatest lift per air horsepower occurs at area ratios above 0.10, where the greatest lift augmentation occurs. The data show that annular-Jet vehicles are unstable at ratios of height above ground to nozzle diameter above about 0.10. The stability of the annular-jet vehicle can be improved by the use of large center jets. Base compartments also reduces the unstable moment.

Goodson, Kenneth W.↗

NASA NTRS1953

High-Speed Wind-Tunnel Tests of a 1/16-Scale Model of the D-558 Research Airplane Lift and Drag Characteristics of the D-558-1 and Various Wing and Tail Configurations

Tests were made in the Langley 8-foot high-speed tunnel to investigate the aerodynamic characteristics of the D-558-1 airplane and various wing and tail configurations on the D-558-1 fuselage. The various wing and tail configurations were tested to determine the aerodynamic effects of aspect ratio and sweep for suitable use on the second phase of the D-558 project (D-558-2). The tests were conducted through a speed range from a Mach number of 0.40 to approximately 0.94.This part of the investigation includes the lift and drag results available for the configurations tested at this rate. The D-558-1 results indicated that the lift force break would occur at a Mach number of 0.85 with some reduction in lift at speeds above this Mach number. Tests indicated that the airplane will have satisfactory lift and drag characteristics up to and including its design Mach number of 0.85. The 35deg sweptback, 35deg swept-forward, and low-aspect-ratio (2.0) wing configurations all showed pronounced improvements in maintaining lift throughout the Mach number range tested and in increasing the critical speeds above the D-558-1 value &itical to critical Mach numbers on the order of 0.9. Insofar as lift and drag characteristics are concerned level flight at speeds approaching the velocity of sound appears practical if swept or low-aspect-ratio configurations similar to those tested are used.

Wright, John D.↗

NASA NTRS1947

Lift and Drag of Wings with Small Span

The lift coefficient of!a wing of small span at first shows a linear increase for the increasing angle of attack, but to a lesser degree then was to be expected according to the theory of the lifting line; thereafter the lift coefficient increases more rapidly than linearity, as contrasted with the the theory of the lifting line. The induced drag coefficient for a given lift coefficient, on the other hand, is obviously much smaller than it would be according to the theory. A mall change in the theory of the lifting line will cover these deviations.

Weinig, F.↗

NASA NTRS2008

Influence of Lift Offset on Rotorcraft Performance

The influence of lift offset on the performance of several rotorcraft configurations is explored. A lift-offset rotor, or advancing blade concept, is a hingeless rotor that can attain good efficiency at high speed, by operating with more lift on the advancing side than on the retreating side of the rotor disk. The calculated performance capability of modern-technology coaxial rotors utilizing a lift offset is examined, including rotor performance optimized for hover and high-speed cruise. The ideal induced power loss of coaxial rotors in hover and twin rotors in forward flight is presented. The aerodynamic modeling requirements for performance calculations are evaluated, including wake and drag models for the high speed flight condition. The influence of configuration on the performance of rotorcraft with lift-offset rotors is explored, considering tandem and side-by-side rotorcraft as well as wing-rotor lift share.

Johnson, Wayne↗

NASA NTRS1954

Effect of a Leading-edge Flap upon the Lift, Drag, and Pitching Moment of an Airplane Employing a Thin, Unswept Wing

The effects of deflecting full-span, constant-chord, leading-edge flaps, having either round or sharp leading edges, upon the lift, drag,. and pitching moment characteristics of a model of an interceptor-type aircraft have been determined experimentally at subsonic and supersonic speeds. Results indicate that the variations of lift with angle of attack and of pitching moment with lift were unaffected by either the shape of the flap leading edge or flap deflection. Deflection of the flaps having either a round or sharp leading edge increased the drag at zero lift at both subsonic and supersonic speeds. In spite of the increase in the drag at zero lift, however, deflection of the flaps increased the maximum lift-drag ratio at subsonic speeds and had no deleterious effect at supersonic speeds.

Heitmeyer, John C.↗

NASA NTRS2009

Influence of Lift Offset on Rotorcraft Performance

The influence of lift offset on the performance of several rotorcraft configurations is explored. A lift-offset rotor, or advancing blade concept, is a hingeless rotor that can attain good efficiency at high speed by operating with more lift on the advancing side than on the retreating side of the rotor disk. The calculated performance capability of modern-technology coaxial rotors utilizing a lift offset is examined, including rotor performance optimized for hover and high-speed cruise. The ideal induced power loss of coaxial rotors in hover and twin rotors in forward flight is presented. The aerodynamic modeling requirements for performance calculations are evaluated, including wake and drag models for the high-speed flight condition. The influence of configuration on the performance of rotorcraft with lift-offset rotors is explored, considering tandem and side-by-side rotorcraft as well as wing-rotor lift share.

Johnson, Wayne↗

NASA NTRS2015

Use of a Viscous Flow Simulation Code for Static Aeroelastic Analysis of a Wing at High-Lift Conditions

In this paper, we present a static aeroelastic analysis of a wind tunnel test model of a wing in high-lift configuration using a viscous flow simulation code. The model wing was tailored to deform during the tests by amounts similar to a composite airliner wing in highlift conditions. This required use of a viscous flow analysis to predict the lift coefficient of the deformed wing accurately. We thus utilized an existing static aeroelastic analysis framework that involves an inviscid flow code (Cart3d) to predict the deformed shape of the wing, then utilized a viscous flow code (Overflow) to compute the aerodynamic loads on the deformed wing. This way, we reduced the cost of flow simulations needed for this analysis while still being able to predict the aerodynamic forces with reasonable accuracy. Our results suggest that the lift of the deformed wing may be higher or lower than that of the non-deformed wing, and the washout deformation of the wing is the key factor that changes the lift of the deformed wing in two distinct ways: while it decreases the lift at low to moderate angles of attack simply by lowering local angles of attack along the span, it increases the lift at high angles of attack by alleviating separation.

Aeroelastic↗