Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

Wind-Tunnel Investigation of the Lift Characteristics of an NACA 27-212 Airfoil Equipped with Two Types of Flap, Special Report

An investigation has been made in the NACA 7- by 10-foot wind tunnel of a large chord NACA 27-212 airfoil with a 20% chord split flap and with two arrangements of a 25.66% chord slotted flap to determine the section lift characteristics as affected by flap deflection for the split flap and as affected by flap deflection, flap position, and slot shape for the slotted flap. For the two arrangements of the slotted flap, the flap positions for maximum section lift are given. Comparable data on the NACA 23012 airfoil equipped with similar flaps are also given. On the basis of maximum section lift coefficient, the slotted flap with an easy slot entry was slightly better than either the split flap or the slotted flap with a sharp slot entry. With both types of flap the decrease in the angle of attack, for maximum section lift coefficient, with flap deflection is large for the NACA 27-212 airfoil as compared with the NACA 23012 airfoil. Also with both flaps, the maximum section lift coefficient obtained with flaps is much lower for the NACA 27-212 airfoil than for the NACA 23012 airfoil.

Swanson, Robert S.↗
NASA NTRS1972

Analysis of the effect of engine characteristics on the external aerodynamics of STOL wing propulsion systems

The effects of engine presssure ratio, engine size, and engine location on the pressure distribution, lift coefficient, and flow field of a STOL wing propulsion system are presented. The flow variables of the engines are included in the two-dimensional potential flow analysis by considering the effects of mass flow coefficient at the engine inlet and thrust coefficient at the engine exit. A functional relation between these coefficients and engine pressure ratio is given. The results of this study indicate that the effect of engine pressure ratio on the external aerodynamics is a function of engine location. For engines located on the bottom of the wing, the highest pressure ratio engine resulted in the highest lift coefficient. For engines located on the top of the wing, the lowest pressure ratio engine resulted in the highest lift coefficient.

Albers, J. A.↗
NASA NTRS1993

Turbulence model evaluation for the prediction of flows over a supercritical airfoil with deflected aileron at high Reynolds number

Navier-Stokes solutions about a supercritical airfoil with aileron deflection have been computed using the CFL3D code coupled with the Baldwin-Lomax, Johnson-King, Baldwin-Barth, and Spalart-Allmaras turbulence models. Computations were made at a Mach number of 0.716 and chord Reynolds numbers of 5, 15, and 25 million. The airfoil was analyzed with both 0 deg and 2 deg (TED) aileron deflections. Comparisons over a range of angles-of-attack showed that solutions obtained using the Baldwin-Barth turbulence model presented the best agreement with experimental pressures and sectional lift coefficients. However, Reynolds number trends in sectional lift coefficient and in aileron effectiveness were not predicted consistently.

Londenberg, W. K.↗
NASA NTRS1939

Tests of an N.A.C.A. 23012 Airfoil with a slotted deflector flap

Section aerodynamic characteristics of a large-chord N.A.C.A. 23012 airfoil with a slotted deflector flap were obtained in the N.A.C.A. 7- by 10-foot wind tunnel. The characteristics of an N.A.C.A. slotted flap and of a simple split flap are included for comparison. The slotted deflector flap was found to have a somewhat lower maximum lift coefficient and somewhat higher drag at high lift coefficients than the N.A.C.A. slotted flap. The high drag of the open slot with the deflector flap neutral indicates that the slot should be closed for this condition.

House, R O↗
NASA NTRS1999

A Reynolds Number Study of Wing Leading-Edge Effects on a Supersonic Transport Model at Mach 0.3

A representative supersonic transport design was tested in the National Transonic Facility (NTF) in its original configuration with small-radius leading-edge flaps and also with modified large-radius inboard leading-edge flaps. Aerodynamic data were obtained over a range of Reynolds numbers at a Mach number of 0.3 and angles of attack up to 16 deg. Increasing the radius of the inboard leading-edge flap delayed nose-up pitching moment to a higher lift coefficient. Deflecting the large-radius leading-edge flap produced an overall decrease in lift coefficient and delayed nose-up pitching moment to even higher angles of attack as compared with the undeflected large- radius leading-edge flap. At angles of attack corresponding to the maximum untrimmed lift-to-drag ratio, lift and drag coefficients decreased while lift-to-drag ratio increased with increasing Reynolds number. At an angle of attack of 13.5 deg., the pitching-moment coefficient was nearly constant with increasing Reynolds number for both the small-radius leading-edge flap and the deflected large-radius leading-edge flap. However, the pitching moment coefficient increased with increasing Reynolds number for the undeflected large-radius leading-edge flap above a chord Reynolds number of about 35 x 10 (exp 6).

Williams, M. Susan↗
NASA NTRS2018

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗
NASA NTRS1946

Langley Full-Scale Tunnel Investigation of a 1/3-Scale Model of the Chance Vought XF5U-1 Airplane

The results of an investigation of a 1/3-scale model of the Chance Vought XF5U-1 airplane in the Langley full-scale tunnel are presented in this report. The maximum lift and stalling characteristics of several model configurations, the longitudinal stability characteristics of the model, and the effectiveness of the control surfaces were determined with the propellers removed. The propulsive characteristics, the effect of propeller operation on the lift, and the static thrust of the model propellers were determined at several propeller-blade angles. The results with the propellers removed showed that the maximum lift coefficient of the complete model configuration was only 0.97 was compared with the value of 1.31 for the model configuration in which the engine-air ducts and canopy are removed. The model with the propellers removed (normal center-of-gravity position) has a positive static margin, stick fixed, varying from 5 to 13 percent of the mean aerodynamic chord throughout the unstalled range of lift coefficients. The unit horizontal tail is sufficiently powerful to trim the airplane with the propellers removed throughout the unstalled range of lift coefficients. The peak propulsive efficiencies for beta = 20 degrees and beta = 30 degrees were increased 7 percent at C(sub L) congruent to 0.67 and 20 percent at C(sub L) congruent to 0.74, respectively, with the propellers rotating upward in the center than with the propellers rotating downward in the center. Indications are that the minimum forward-flight speed of the airplane for full-power operation at sea level will be about 90 miles per hour. Decreasing the weight and increasing the power reduced this value of minimum speed and there were no indications from the results of a lower limit to the minimum speed.

Lange, Roy H.↗
NASA NTRS1982

An experimental and theoretical investigation of thick wings at various sweep angles in and out of ground effect

The effects of sweep and aspect ratio on the longitudinal aerodynamics of a wing in and out of ground effect are analyzed. Experimental data were obtained in the Langley 4 by 7 Meter Tunnel for a wing with various sweep angles, aspect ratios, and flap deflections both in and out of ground effect. Theoretical predictions of the out of ground effect lift coefficients and flap effectiveness and the in ground effect lift coefficients are compared with the experimental results. As expected, the lift curve slope and flap effectiveness are reduced when the aspect ratio is reduced or the sweep angle is increased both in and out of ground effect. In ground effect, the lift and flap effectiveness are increased above a wing height to span ratio of 0.15. However, with flap deflections less than or equal to 10 deg and an angle of attack near 0 deg lift is markedly decreased at very low heights above the ground plane. This trend is not predicted by planar theoretical models but is predicted by a surface panel method where thickness effects are included.

Paulson, J. W., Jr.↗
NASA NTRS1942

Preliminary Investigation in the NACA Low-Turbulence Tunnel of Low-drag Airfoil Sections Suitable for Admitting Air at the Leading Edge

An investigation was carried out in the NACA low-turbulence tunnel to develop low-drag airfoil sections suitable for admitting air at the leading edge. A thickness distribution having the desired type of pressure distribution was found from tests of a flexible model. Other airfoil shapes were derived from this original shape by varying the thickness, the camper, the leading-edge radius, and the size of the leading-edge opening. Data are presented giving the characteristics of the airfoil shapes in the range of lift coefficients for high-speed and cruising flight. Shapes have been developed which show no substantial increases in drag over that of the same position along the chord. Many of these shapes appear to have higher critical compressibility speeds than plain airfoils of the same thickness. Low-drag airfoil sections have been developed with openings in the leading edge as large as 41.5 percent of the maximum thickness. The range of lift coefficients for low drag in several cases is nearly as large as that of the corresponding plain airfoil sections. Preliminary measurements of maximum lift characteristics indicate that nose-opening sections of the type herein considered may not produce any marked effects on the maximum lift coefficient.

WING DUCTS↗
NASA NTRS1939

Tests of Airfoils Designed to Delay the Compressibility Burble

Development of airfoil sections suitable for high-speed applications has generally been difficult because little was known of the flow phenomenon that occurs at high speeds. A definite critical speed has been found at which serious detrimental flow changes occur that lead to serious losses in lift and large increases in drag. This flow phenomenon, called the compressibility burble, was originally a propeller problem, but with the development of higher speed aircraft serious consideration must be given to other parts of the airplane. Fundamental investigations of high-speed airflow phenomenon have provided new information. An important conclusion of this work has been the determination of the critical speed, that is, the speed at which the compressibility burble occurs. The critical speed was shown to be the translational velocity at which the sum of the translational velocity and the maximum local induced velocity at the surface of the airfoil or other body equals the local speed of sound. Obviously then higher critical speeds can be attained through the development of airfoils that have minimum induced velocity for any given value of the lift coefficient. Presumably, the highest critical speed will be attained by an airfoil that has uniform chordwise distribution of induced velocity or, in other words, a flat pressure distribution curve. The ideal airfoil for any given high-speed application is, then, that form which at its operating lift coefficient has uniform chordwise distribution of induced velocity. Accordingly, an analytical search for such airfoil forms has been conducted and these forms are now being investigated experimentally in the 23-inch high-speed wind tunnel. The first airfoils investigated showed marked improvement over those forms already available, not only as to critical speed buy also the drag at low speeds is decreased considerably. Because of the immediate marked improvement, it was considered desirable to extend the thickness and lift coefficient ranges for which the original forms had been designed before further extending the investigation.

Stack, John↗
NASA NTRS1933

Wind-tunnel tests on model wing with Fowler flap and specially developed leading-edge slot

An investigation was made in the NACA 7 by 10 foot wind tunnel to find the increase in maximum lift coefficient which could be obtained by providing a model wing with both a Fowler trailing-edge extension flap and a Handley Page type leading-edge slot. A conventional Handley page slot proportioned to operate on the plain wing without a flap gave but a slight increase with the flap; so a special form of slot was developed to work more effectively with the flap. With the best combined arrangement the maximum lift coefficient based on the original area was increased from 3.17, for the Fowler wing, to 3.62. The minimum drag coefficient with both devices retracted was increased in approximately the same proportion. Tests were also made with the special-type slot on the plain wing without the flap. The special slot, used either with or without the Fowler flap, gave definitely higher values of the maximum lift coefficient than the slots of conventional form, with an increase of the same order in the minimum drag coefficient.

WING SLOTS & FLAPS, FOWLER↗
NASA NTRS1996

Experimental and computational investigation of lift-enhancing tabs on a multi-element airfoil

An experimental and computational investigation of the effect of lift enhancing tabs on a two-element airfoil was conducted. The objective of the study was to develop an understanding of the flow physics associated with lift enhancing tabs on a multi-element airfoil. A NACA 63(sub 2)-215 ModB airfoil with a 30 percent chord Fowler flap was tested in the NASA Ames 7 by 10 foot wind tunnel. Lift enhancing tabs of various heights were tested on both the main element and the flap for a variety of flap riggings. Computations of the flow over the two-element airfoil were performed using the two-dimensional incompressible Navier-Stokes code INS2D-UP. The computer results predict all of the trends in the experimental data quite well. When the flow over the flap upper surface is attached, tabs mounted at the main element trailing edge (cove tabs) produce very little change in lift. At high flap deflections. however, the flow over the flap is separated and cove tabs produce large increases in lift and corresponding reductions in drag by eliminating the separated flow. Cove tabs permit high flap deflection angles to be achieved and reduce the sensitivity of the airfoil lift to the size of the flap gap. Tabs attached to the flap training edge (flap tabs) are effective at increasing lift without significantly increasing drag. A combination of a cove tab and a flap tab increased the airfoil lift coefficient by 11 percent relative to the highest lift tab coefficient achieved by any baseline configuration at an angle of attack of zero percent and the maximum lift coefficient was increased by more than 3 percent. A simple analytic model based on potential flow was developed to provide a more detailed understanding of how lift enhancing tabs work. The tabs were modeled by a point vortex at the training edge. Sensitivity relationships were derived which provide a mathematical basis for explaining the effects of lift enhancing tabs on a multi-element airfoil. Results of the modeling effort indicate that the dominant effects of the tabs on the pressure distribution of each element of the airfoil can be captured with a potential flow model for cases with no flow separation.

Ashby, Dale↗
NASA NTRS1995

Airfoil modification effects on subsonic and transonic pressure distributions and performance for the EA-6B airplane

Longitudinal characteristics and wing-section pressure distributions are compared for the EA-6B airplane with and without airfoil modifications. The airfoil modifications were designed to increase low-speed maximum lift for maneuvering, while having a minimal effect on transonic performance. Section contour changes were confined to the leading-edge slat and trailing-edge flap regions of the wing. Experimental data are analyzed from tests in the Langley 16-Foot Transonic Tunnel on the baseline and two modified wing-fuselage configurations with the slats and flaps in their retracted positions. Wing modification effects on subsonic and transonic performance are seen in wing-section pressure distributions of the various configurations at similar lift coefficients. The modified-wing configurations produced maximum lift coefficients which exceeded those of the baseline configuration at low-speed Mach numbers (0.300 and 0.400). This benefit was related to the behavior of the wing upper surface leading-edge suction peak and the behavior of the trailing-edge pressure. At transonic Mach numbers (0.725 to 0.900), the wing modifications produced a somewhat stronger nose-down pitching moment, a slightly higher drag at low-lift levels, and a lower drag at higher lift levels.

Allison, Dennis O.↗
NASA NTRSDate not supplied

Multi-point Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a multi-point jig twist optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic small disturbance /integral boundary layer correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. The VSPAERO model has been validated against wind tunnel test data and FUN3D CFD simulation data. Three different flight conditions corresponding to Mach 0.745 at 40,000 ft are selected for the TTBW aircraft jig twist optimization to reduce the drag coefficients at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized jig twist achieves a drag reduction of about 9 counts, 7 counts, and8 counts corresponding to the lift coefficients 0.68, 0.73, and 0.78, respectively. A high-fidelity CFD solver FUN3D is used to validate the jig twist optimization.

Multi-point↗
NASA NTRS1986

Aero-assisted orbital plane change using an elliptic drag polar

A three-impulse, aero-assisted maneuver is used to change the plane of a circular orbit. The guidance law used during the atmospheric phase is based on the repetitive use of an approximate optimal control law. The approximations include Loh's term being constant, an exponential atmosphere, and a constant-coefficient drag polar. Whereas the true optimal trajectory is flown at maximum lift-to-drag ratio, simulation results for a parabolic drag polar show the angle of attack becoming large near the end of the trajectory. Here, the approximate optimal control rule is developed for an elliptic polar which has maximum lift coefficient and higher values of the drag coefficient at high values of the lift coefficient than the parabolic polar. Simulation results show that the angle of attack still increases to high values near the end of the trajectory and that, overall, the parabolic drag polar produces better results. Finally, it is shown that Loh's term is not constant over the ascent portion of the atmospheric turn and is the probable cause of high angles of attack. However, the guidance laws developed by assuming Loh's term to be constant work well.

Hull, D. G.↗
NASA NTRS1995

Lift-Enhancing Tabs on Multielement Airfoils

The use of flat-plate tabs (similar to Gurney flaps) to enhance the lift of multielement airfoils is extended here by placing them on the pressure side and near the trailing edge of the main element rather than just on the furthest downstream wing element. The tabs studied range in height from 0.125 to 1.25% of the airfoil reference chord. In practice, such tabs would be retracted when the high-lift system is stowed. The effectiveness of the concept was demonstrated experimentally and computationally on a two-dimensional NACA 63(sub 2)-215 Mod B airfoil with a single-slotted, 30%-chord flap. Both the experiments and computations showed that the tabs significantly increase the lift at a given angle of attack and the maximum lift coefficient of the airfoil. The computational results showed that the increased lift was a result of additional turning of the flow by the tab that reduced or eliminated now separation on the flap. The best configuration tested, a 0.5%-chord tab placed 0.5% chord upstream of the trailing edge of the main element, increased the maximum lift coefficient of the airfoil by 12% and the maximum lift-to-drag ratio by 40%.

Ross, James C.↗
NASA NTRS1973

Low speed aerodynamic characteristics of a 17 percent thick airfoil section designed for general aviation applications

Wind-tunnel tests have been conducted to determine the low-speed two-dimensional aerodynamic characteristics of a 17-percent-thick airfoil designed for general aviation applications (GA(W)-1). The results were compared with predictions based on a theoretical method for calculating the viscous flow about the airfoil. The tests were conducted over a Mach number range from 0.10 to 0.28. Reynolds numbers based on airfoil chord varied from 2.0 million to 20.0 million. Maximum section lift coefficients greater than 2.0 were obtained and section lift-drag ratio at a lift coefficient of 1.0 (climb condition) varied from about 65 to 85 as the Reynolds number increased from about 2.0 million to 6.0 million.

Mcghee, R. J.↗
NASA NTRS1932

The aerodynamic characteristics of a model wing having a split flap deflected downward and moved to the rear

Tests were made on a model wing with three different sized split trailing-edged flaps, in the NACA 7 by 10 foot wind tunnel. The flaps were formed of the lower rear portion of the wing and were rotated downward about axes at their front edges. The lift, drag, and center of pressure were measured with the axis in its original position and also with it moved back in even steps to the trailing edge of the main wing, giving in effect an increase in area. The split flaps when deflected about their original axis locations gave slightly higher maximum lift coefficients than conventional trailing-edge flaps, and the lift coefficients were increased still further by moving the axes toward the rear. The highest value of C(sub L max), which was obtained with the largest flap hinged at 90 per cent of the chord from the leading edge, was 2.52 as compared with 1.27 for the basic wing.

Weick, Fred E↗