Search NASA⌕ Search

SEARCH · Search NASA

Results for “MYLAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Optical measurement of the velocity of dielectric surface arcs

Surface flashover arc discharge velocities on electron-beam-charged polymer sheets have been measured directly by detecting the light emitted at two points along a straight arc and measuring the time interval between light pulses. For Mylar, the average velocity is 1.2 x 10 to the 6th m/s, and for Teflon the average velocity is approximately 7.3 x 10 to the 5th m/s independent of sheet thickness. These velocities are about two to four times higher than previous measurements. The techniques employed to produce single, straight surface arcs are described.

Balmain, K. G.↗
NASA NTRS1982

Barriers to flashover discharge arcs on Teflon

The effect of various barriers (empty gap, copper, Mylar, and nickel mesh) on the probability of simultaneous arc discharging of two physically separated pieces of electron-beam-charged Teflon was studied. For the empty gap barrier, it was found that simultaneous discharges rarely occur when the separation between the samples is greater than approximately 0.4 times the length of their common edge when this length is of the order of 1 cm. Evidence suggests that electromagnetic fields play a larger role than electrons in influencing the occurrence of simultaneous arc discharges.

Gossland, M.↗
NASA NTRS1982

Charging and discharging characteristics of dielectric materials exposed to low- and mid-energy electrons

Charging and discharging characteristics of dielectric samples exposed to 1-25 keV and 25-100 keV electrons in a laboratory environment are reported. The materials examined comprised OSR, Mylar, Kapton, perforated Kapton, and Alphaquartz, serving as models for materials employed on spacecraft in geosynchronous orbit. The tests were performed in a vacuum chamber with electron guns whose beams were rastered over the entire surface of the planar samples. The specimens were examined in low-impedance-grounded, high-impedance-grounded, and isolated configurations. The worst-case and average peak discharge currents were observed to be independent of the incident electron energy, the time-dependent changes in the worst case discharge peak current were independent of the energy, and predischarge surface potentials are negligibly dependent on incident monoenergetic electrons.

Coakley, P.↗
NASA NTRS1983

Tensile stress-strain behavior of hybrid composite laminates

A study was made of the stress-strain response of several hybrid laminates, and the damage was correlated with nonlinear stress-strain response and ultimate strength. The fibers used in the laminates were graphite, S-glass, and Kevlar. Some laminates with graphite fibers had perforated Mylar film between plies, which lowered the interlaminar bond strength. The laminate configurations were chosen to be like those of buffer strips in large panels and fracture coupons. Longitudinal and transverse specimens were loaded in tension to failure. Some specimens were radiographed to reveal damage due to edge effects. Stress-strain response is discussed in terms of damage shown by the radiographs. Ultimate strengths are compared with simple failure criteria, one of which account for damage.

Kennedy, J. M.↗
NASA NTRS1983

Fracture behavior of hybrid composite laminates

The tensile fracture behavior of 15 center-notched hybrid laminates was studied. Three basic laminate groups were tested: (1) a baseline group with graphite/epoxy plies, (2) a group with the same stacking sequence but where the zero-deg plies were one or two plies of S-glass or Kevlar, and (3) a group with graphite plies but where the zero-deg plies were sandwiched between layers of perforated Mylar. Specimens were loaded linearly with time; load, far field strain, and crack opening displacement (COD) were monitored. The loading was stopped periodically and the notched region was radiographed to reveal the extent and type of damage (failure progression). Results of the tests showed that the hybrid laminates had higher fracture toughnesses than comparable all-graphite laminates. The higher fracture toughness was due primarily to the larger damage region at the ends of the slit; delamination and splitting lowered the stress concentration in the primary load-carrying plies. A linear elastic fracture analysis, which ignored delamination and splitting, underestimated the fracture toughness. For almost all of the laminates, the tests showed that the fracture toughness increased with crack length. The size of the damage region at the ends of the slit and COD measurements also increased with crack length.

Kennedy, J. M.↗
NASA NTRS1982

Progress report on the infrared astronomical satellite cryogenic system

The main cryogen tank is sized to hold 70 kg of superfluid helium with 12 percent ullage at a temperature of 1.8 K. The insulation system surrounds the main cryogen tank with four blankets of multilayer insulation spaced by means of three vapor-cooled shields. It is noted that the multilayer insulation is 6.4 micron double-aluminized Mylar separated by polyester net. The main shell provides the primary structural integrity of the system. In orbit the main shell is cooled to 170 K using insulation blankets on one side and second surface paint on the opposite side. The aperture cover subassembly is the vacuum seal for the main shell during operation on the ground. It is also a gas condensation trap before and during cooldown of the main cryogen tank during launch hold. It contains 6 kg of supercritical helium, which permits 14 days on orbit with a 48-hour launch pad hold.

Urbach, A. R.↗
NASA NTRS1984

The Effect of Point-spread Function Interaction with Radiance from Heterogeneous Scenes on Multitemporal Signature Analysis

The point-spread function is an important factor in determining the nature of feature types on the basis of multispectral recorded radiance, particularly from heterogeneous scenes and particularly from scenes which are imaged repetitively, in order to provide thematic characterization by means of multitemporal signature. To demonstrate the effect of the interaction of scene heterogeneity with the point spread function (PSF)1, a template was constructed from the line spread function (LSF) data for the thematic mapper photoflight model. The template was in 0.25 (nominal) pixel increments in the scan line direction across three scenes of different heterogeneity. The sensor output was calculated by considering the calculated scene radiance from each scene element occurring between the contours of the PSF template, plotted on a movable mylar sheet while it was located at a given position.

Duggin, M. J.↗
NASA NTRS1984

A nonlinear structural concept for drag-reducing compliant walls

Two mechanisms of drag reduction for flow over flat plates were investigated. The first mechanism employs Bushnell's hypothesis that compliant walls produce drag reduction by interfering with the formation of the turbulent spots in a turbulent boundary layer. It is shown that the amplitudes and frequencies of compliant wall motions for drag reduction might be achieved by using slightly curved walls and the resulting large amplitude motions of snap buckling. A simple structural model of an arch is used in the analysis, and an asymptotic method is developed. The required wall motions can be obtained by using materials like mylar. In addition, the delay of transition from laminar to turbulent flow by driven walls was studied for Poiseuille channel flow. The walls are driven by a periodic traveling wave. A significant increase in the transitional Reynolds number is obtained by appropriately prescribing the wavelength and phase velocity of the wall motion. Previously developed asymptotic methods are used in the analysis. Previously announced in STAR as N83-11061

Reiss, E. L.↗
NASA NTRS1983

Clinostat effects on shoot and root of Arabidopsis

In the clinostat environment, Arabidopsis thaliana (L.) Heynh. plants grown in cultures having limited gas exchange with the external atmosphere developed 'above' the agar media a large mass of roots which eventually covered the stem. Cultural conditions were 0.5 rpm, 350 ft.c. from cool white fluorescent lamps, and 25 C. Limited gas exchange culture tubes were covered with Saran Wrap or mylar film, while free gas exchange cultures were plugged with cotton or polyurethane foam. Average shoot-root dry weight ratio of clinostatted, limited gas exchange plants was 3.39 (p less than 0.001) as compared to 10.1 for upright stationary and 10.3 for vertically rotated controls. Average dry weight (48.3 mg) of all clinostatted shoots was greater than those reported by other investigators (15.1 mg). Finally, shoots of the clinostatted plants reported here were almost 2x heavier (p less than 0.01) than the controls (28.7 mg, 26.7 mg), a result contrary to findings of previous investigators, where the clinostatted plants are the lightest (clinostat 15.1 mg, controls 16.5 mg and 17.2 mg).

Hoshizaki, T.↗
NASA NTRS1984

Electron capture by U(91+) and U(92+) and ionization of U(90+) and U(91+)

U(92+)/U(91+) and U(91+)/U(90+) electron-capture and ionization cross sections and equilibrium charge-state distributions are measured experimentally in mylar, Cu and Ta of varying thickness. Relativistic U(68+) ions at 437 or 962 MeV/nucleon are produced by a heavy-ion linear accelerator and synchrotron in tandem and passed through the target material into a magnetic specrometer and position-sensitive proportional counter for evaluation of charge states. The results are presented graphically and discussed. At 962 MeV/nucleon, beams containing 85 percent bare U(92+) nuclei are obtained using 150-mg/sq cm Cu or 85-mg/sq cm Ta; at 437 MeV/nucleon, 50 percent bare U(92+) nuclei are obtained with 90-mg/sq cm Cu. The techniques decribed can be applied to produce beams of bare U nuclei for acceleration to ultrarelativistic speeds or beams of few-electron U for atomic-physics experiments on quantum electrodynamics.

Gould, H.↗
NASA NTRS1985

Local heat-transfer measurements on a large, scale-model turbine blade airfoil using a composite of a heater element and liquid crystals

Local heat transfer coefficients were experimentally mapped along the midchord of a five-time-size turbine blade airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a mylar sheet with a layer of cholesteric liquid crystals, that change color with temperature, and a heater sheet made of a carbon-impregnated paper, that produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. The local heat transfer coefficients are presented for Reynolds numbers from 2.8 x 10 to the 5th power to 7.6 x 10 to the 5th power. Comparisons are made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code. Also, a leading edge separation bubble was revealed by thermal and flow visualization.

Hippensteele, S. A.↗
NASA NTRS1985

A consideration of atomic oxygen interactions with space station

A computer model is developed in order to calculate fluence for a generalized spacecraft in orbital flight based on mass spectrometer and incoherent scatter (MSIS) measurements of ambient density. The calculations are used to identify criteria for the selection of materials for the construction of an LEO Space Station. The model is generalized such that the surfaces for study can be oriented in any direction with respect to: a body coordinate system fixed to the spacecraft (E surfaces); and a solar inertial coordinate system. A parametric study was performed in order to evaluate the effects of altitude, inclination, and solar activity on atomic oxygen fluence. Values are obtained for samples of Mylar, Kevlar, Kapton, Tedlar, Teflon and sulfone, as well as for some ethylene polymers. The range of values for material reactivities is from 360 microns for ram-facing surfaces to 200 microns for solar power surfaces during each cycle of solar activity. The possibility of improving reactivity by employing certain chemical coatings is also discussed.

Leger, L. J.↗
NASA NTRS1985

Studies of molecular properties of polymeric materials: Aerospace environmental effects on three linear polymers

The development of crystal handling techniques for reflection infrared spectroscopy and methods for the fabrication and testing of tensile specimens are discussed. Data from mechanical, ac and dc electrical, and electron paramagnetic resonance studies conducted to determine the effects of 0.1-MeV and 1.0-MeV electron radiation on Mylar, Kapton, Ultem, and metal-doped Ultem are presented. Total doses ranging from 1 X 10 to the 8 rads to 1 X 10 to the 10 rads and dose rates from 5 X 10 to the 7 rads/hr to 1 X 10 to the 9 rads/hr were employed. The results of a study on the effects of aircraft service-environment fluids on Ultem are also reported. The weights and mechanical properties of Ultem were evaluated before and after exposure to water, JP4, Skydrol, an antifreeze, and a paint stripper.

Harries, W. L.↗
NASA NTRS1986

Effects of partial interlaminar bonding on impact resistance and loaded-hole behavior of graphite/epoxy quasi-isotropic laminates

A partial-bonding interlaminar toughening concept was evaluated for resistance to impact and for behavior of a loaded hole. Perforated Mylar sheets were interleaved between all 24 plies of a graphite/epoxy quasi-isotropic lay-up. Specimens were impacted by aluminum spheres while under tensile or compressive loads. Impact-failure thresholds and residual strengths were obtained. Loaded-hole specimens were tested in three configurations that were critical in bearing, shear, or tension. Partial bonding reduced the tensile and compressive strengths of undamaged specimens by about one-third. For impact, partial bonding did not change the threshold for impact failure under tensile preload. However, under compressive preload, partial bonding caused serious degradation of impact resistance. Partial bonding reduced the maximum load-carrying capacity of all three types of loaded-hole specimens. Overall, partial bonding degraded both impact resistance and bearing strength of holes.

Illg, W.↗
NASA NTRS1985

Local heat-transfer measurements on a large scale-model turbine blade airfoil using a composite of a heater element and liquid crystals

Local heat transfer coefficients were experimentally mapped along the midchord of a five-time-size turbine blade airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a mylar sheet with a layer of cholesteric liquid crystals, that change color with temperature, and a heater sheet made of a carbon-impregnated paper, that produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. The local heat transfer coefficients are presented for Reynolds numbers from 2.8 x 10 to the 5th power to 7.6 x 10 to the 5th power. Comparisons are made with analytical values of heat transfer coefficients obtained from the STANS boundary layer code. Also, a leading edge separation bubble was revealed by thermal and flow visualization.

Hippensteele, S. A.↗
NASA NTRS1986

A new method for fabrication of diamond-dust blocking filters

Thermal embedding of diamond dust onto a polyethylene-coated Al plate has been used to make a blocking filter for FIR applications. The Al plate is sandwiched between two Mylar 'blankets' and the air between the layers is removed by means of a small vacuum pump. After the polyethylene is heated and softened, the diamond dust is applied to the polyethylene coating using a brush. The optimum diamond dust grain sizes corresponding to polyethylene layer thicknesses of 9-12 microns are given in a table, and the application of the blocking filter to spectrometric measurements in the FIR is described. An exploded view diagram of the layered structure of the blocking filter is provided.

Collard, H. R.↗
NASA NTRS1985

Measurements of the elemental and isotopic composition of interplanetary dust collected on LDEF

A passive interplanetary dust collection experiment, currently in orbit aboard the Long Duration Exposure Facility, is described. The collectors, germanium target plates covered by metallized Mylar foils, are designed for secondary ion mass spectrometry measurements of the elemental and isotopic compositions of residues resulting from micrometeoroid (greater than 10 to the -10th grams) impacts. Impact simulation experiments have demonstrated the validity of the collection concept. Quantitative elemental analyses are complicated by the nonuniform distribution of projectile-derived elements.

Fechtig, H.↗
NASA NTRS1986

Mass spectrometric studies of the electrical breakdown of thin polymer films

The composition of the neutral particles released during the electrical breakdown of 50-micron and 75-micron insulating films of the type used on spacecraft exteriors investigated experimentally using a time-of-flight mass spectrometer triggered by the breakdown event. The experimental apparatus is described in detail, and the results are presented in photographs. It is found that the particle flux from Teflon FEP and PFA films comprise mainly fluorocarbon fragments, some with mass 350 amu or greater, but the flux from Kapton oxygen-ion-beam treated Kapton, Tefzel, and Mylar comprises mainly molecules of mass 44 amu or less.

Kendall, B. R. F.↗